Canon imageFORMULA CR-190i II Manuale del proprietario

Please read this manual before operating this scanner.

Instructions

2

Connecting the Scanner to a Computer

Connect the CR-135i II/CR-190i II to a computer as follows. Make sure

to install the software before connecting the scanner to a computer.

• If you connect the computer and turn ON the CR-135i II/CR-190i II

before installing the software, the following wizard screen appears. If

this happens, click [Cancel], turn OFF the CR-135i II/CR-190i II, and

then install the software.

The following wizard screen is an example in Windows 7. When a

similar wizard screen appears in Windows 8.1/10, click [Cancel].

A Install the software

Install the Scanning Utility for CR-135i/CR-190i in the setup disc

provided with the CR-135i II/CR-190i II. (See “Installing the

Software,” on p. 18.)

B Connect the scanner to a computer

Connect the CR-135i II/CR-190i II and the computer with a USB.

(See “Connecting the Scanner to a Computer,” on p. 19.)

C Turn ON the power

Turn ON the power of the CR-135i II/CR-190i II. (See “Turning ON

the Power,” on p. 20.)

D Automatically installing the device driver

The device driver is installed automatically when Windows

recognizes the CR-135i II/CR-190i II as new hardware. (See

p. 21.)

Wizard Screen (Windows 7)

3

FCC REGULATIONS (For 120V model)

Check Reader, Model M111071/M111021/M111072/M111022

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If

such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A. Inc.

One Canon Park, Melville, NY 11747, U.S.A.

Tel. No. (800)652-2666

RADIO INTERFERENCE REGULATIONS (For 120V models)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus

as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the

Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For

120V models)

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils

numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”,

NMB-003 édictée par l’Industrie Canada.

ENERGY STAR

®

Office Equipment Program

This program is for U.S.A and Canada.

As an ENERGY STAR

®

Partner, CANON ELECTRONICS INC. has determined that this

machine meets the ENERGY STAR

®

Program guidelines for energy efficiency.

The ENERGY STAR

®

Office Equipment Program is an international program that promotes

energy saving through the use of computers and other office equipment. The program

backs the development and dissemination of products with functions that effectively reduce energy

consumption. It is an open system in which business proprietors can participate voluntarily. The targeted

products are office equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners.

The standards and logos are uniform among participating nations.

This model doesn’t provide “setting options” for power management.

European Union (and EEA) only.

This symbol indicates that this product is not to be disposed of with your household waste,

according to the WEEE Directive (2002/96/EC) and your national law. This product should

be handed over to a designated collection point, e.g., on an authorized one-for-one basis

when you buy a new similar product or to an authorized collection site for recycling waste

electrical and electronic equipment (EEE). Improper handling of this type of waste could have

a possible negative impact on the environment and human health due to potentially hazardous substances

that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this

product will contribute to the effective usage of natural resources. For more information about where you

can drop off your waste equipment for recycling, please contact your local city office, waste authority,

approved WEEE scheme or your household waste disposal service. For more information regarding return

and recycling of WEEE products, please visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

Für EMVG

Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich sowie in

Kleinbetrieben vorgesehen.

Model Names

The following names may be provided for the safety regulations in each sales region of the Check Reader.

CR-135i II: Model M111071

CR-190i II: Model M111021

CR-135i II UV: Model M111072

CR-190i II UV: Model M111022

4

Trademarks

• Canon and the Canon logo are registered trademarks, of Canon Inc.

in the United States and may also be trademarks or registered

trademarks in other countries.

• imageFORMULA is a trademark of CANON ELECTRONICS INC.

• Microsoft, Windows, Windows 7, Windows 8.1 and Windows 10 are

registered trademarks or trademarks of Microsoft Corporation in the

United States and other countries.

• Microsoft product screen shot(s) reprinted with permission from

Microsoft Corporation.

• Adobe, Acrobat, and Adobe Reader are registered trademarks or

trademarks of Adobe Systems Incorporated in the United States and

other countries.

• Other product and company names herein are, or may be, the

trademarks of their respective owners.

• Ranger is a trademark of Silver Bullet technology, Inc.

Copyright

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying and recording, or by any information storage or retrieval system

without the prior written permission of CANON ELECTRONICS INC.

Reproduction Warning

This device is designed to be used in a legal manner, in accordance with all applicable laws, including, but

not limited to, counterfeit and copyright laws, as well as laws pertaining to national security.

Any person(s) found to have reproduced any of the following materials (regardless of whether such

reproduction was intentional or not) for the purpose of misrepresenting such material as the original may

be prosecuted in accordance with the applicable laws and regulations.

• Paper money or bank notes (domestic and foreign)

• Postage stamps, revenue stamps, or other similar stamps

• Stock certificates, bond certificates, promissory notes, cheques, or

other valuable certificates

• Passports, licenses, or other certificates or documents issued by

government officials or agencies

This is not an exhaustive list.

Canon is not responsible for how this scanner is used by an individual.

Please note that certain intellectual property is protected by copyright law, and copyrighted items may not

be reproduced without the express permission of the copyright holder except for personal or household

use under limited circumstances.

Disclaimers

The information in this document is subject to change without notice.

CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL,

EITHER EXPRESS OR IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION,

THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OF USE OR NON-INFRINGEMENT. CANON ELECTRONICS INC. SHALL NOT BE LIABLE FOR

ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.

CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE AND HANDLING OF DOCUMENTS

SCANNED WITH THIS PRODUCT, OR THE STORAGE AND HANDLING OF THE RESULTING SCANNED

IMAGE DATA.

IF YOU INTEND TO DISCARD THE ORIGINALS OF THE SCANNED DOCUMENTS, YOU ARE

RESPONSIBLE FOR INSPECTING THE SCANNED IMAGES AND VERIFYING THAT THE DATA IS INTACT.

THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. UNDER THIS WARRANTY IS LIMITED TO THE

PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY.

5

INTRODUCTION

Thank you for purchasing the Canon Check Reader CR-135i II/CR-

190i II.

Please read this manual thoroughly before using the machine in order

to familiarize yourself with its capabilities, and to make the most of its

many functions. Unless otherwise noted, CR-190i II is used for both the

CR-190i II and the CR-190i II UV models, and CR-135i II is used for

both the CR-135i II and the CR-135i II UV models, throughout this

manual.

Manuals for the CR-135i II/CR-190i II

The following manuals are provided with the CR-135i II/CR-190i II. Be

sure to read these manuals thoroughly before using the scanner. (The

Installation Guide and the Operation & Maintenance Guide are

extracted from the Instructions.) Electronic manual is stored as a PDF

file on the supplied Setup Disc and requires Adobe Reader to open.

(You can download Adobe Reader from the Adobe Web site.)

Installation Guide (Supplied with the scanner/Electronic Manual)

Describes the procedure for setting up the CR-135i II/CR-190i II for

scanning. Set up the CR-135i II/CR-190i II in accordance with the

Installation Guide. For details on the CR-135i II/CR-190i II, refer to the

Instructions (electronic manual).

Operation & Maintenance Guide (Supplied with the scanner/

Electronic Manual)

Describes the basic operations for using the CR-135i II/CR-190i II,

troubleshooting, and maintenance. For details on the settings of the

CR-135i II/CR-190i II, refer to the Instructions (electronic manual).

Instructions (Electronic Manual): This Manual

Describes how to use the scanner, and includes instructions for

configuring the scanner settings, as well as handling, maintenance,

and troubleshooting information.

Symbols Used in This Manual

The following symbols are used in this manual to explain procedures,

restrictions, handling precautions, and instructions that should be

observed for safety.

WARNING

Indicates a warning concerning operations that may lead to death or

injury to persons if not performed correctly. To use the machine safely,

always pay attention to these warnings.

CAUTION

Indicates a caution concerning operations that may lead to injury to

persons, or damage to property if not performed correctly. To use the

machine safely, always pay attention to these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Be sure to read

these items carefully to operate the machine correctly, and avoid

damaging the machine.

NOTE

Indicates a clarification of an operation, or contains additional

explanations for a procedure. Reading these notes is highly

recommended.

6

Table of Contents

Connecting the Scanner to a Computer............................................... 2

INTRODUCTION ................................................................................. 5

Manuals for the CR-135i II/CR-190i II...................................... 5

Symbols Used in This Manual.................................................. 5

Important Safety Instructions ............................................................... 8

Handling................................................................................... 8

Installation Location ................................................................. 9

Power Supply......................................................................... 10

Moving the Scanner ............................................................... 10

Introduction to the CR-135i II/CR-190i II............................................ 11

Features of the CR-135i II/CR-190i II .......................................... 11

Features ................................................................................. 11

Packaging: What Is in the Box? ................................................... 12

Part Names .................................................................................. 13

Front View .............................................................................. 13

Rear View............................................................................... 15

Connector............................................................................... 15

Exterior Dimensions..................................................................... 15

Preparation Before Use ..................................................................... 16

Setting Up the Scanner................................................................ 16

Checking Your Operating Environment ....................................... 17

Installing the Software.................................................................. 18

Installing the Scanning Utility ................................................. 18

Connecting the Scanner to a Computer....................................... 19

USB Connections................................................................... 19

Connecting the Power Cord................................................... 20

Turning ON and OFF the Power.................................................. 20

Turning ON the Power ........................................................... 20

Turning OFF the Power.......................................................... 21

Preparing the Ink Cartridge.......................................................... 22

About the Ink Cartridge .......................................................... 22

Setting the Ink Cartridge and Adjusting the Print Position ..... 22

Software............................................................................................. 24

How to Use the Software ............................................................. 24

How to Use the Scanning Utility............................................. 24

How to Use the Ranger.......................................................... 26

Uninstalling the Software ............................................................. 27

Document Feeding and Scanning...................................................... 29

Documents................................................................................... 29

Document............................................................................... 29

Envelope ................................................................................ 30

Using Ultrasonic Double Feed Detection ............................... 31

Placing Documents ................................................................ 31

Document Feeding and Scanning................................................ 32

Scan Procedure ..................................................................... 33

Separation OFF Mode............................................................ 35

Auto Power OFF Settings ...................................................... 35

Troubleshooting ................................................................................. 37

When the Scanner Is Not Recognized......................................... 37

Clearing Paper Jams ................................................................... 37

Feeding Trouble........................................................................... 39

When the Scanned Image Is Not Normal .................................... 41

7

Maintenance ...................................................................................... 42

Daily Cleaning.............................................................................. 42

Cleaning the Main Unit........................................................... 42

Cleaning the Feed Path ......................................................... 42

Cleaning the Scanning Glass and Rollers.............................. 44

Cleaning the Magnetic Heads................................................ 47

Cleaning the Ink Jet Nozzles.................................................. 48

Cleaning with the Cleaning Cards (United States Only) ........ 49

Maintenance ................................................................................ 50

Replacing the Ink Cartridge.................................................... 50

Replacing the Ink Disposal Tank............................................ 51

Replacing the Rollers ............................................................. 53

Adjusting the Separation Roller Gap...................................... 56

Specifications............................................................................... 57

Scanner Specifications........................................................... 57

Index .................................................................................................. 58

8

Important Safety Instructions

Handling

WARNING

■ Never install and operate the scanner near flammable substances,

such as alcohol, paint thinner, benzene, or any other type of volatile

solution.

■ Never damage or modify the power cord, and never place heavy

objects on the power cord.

■ Always make sure that your hands are dry when you are handling

the power cord or power plug. Never grasp the power plug when

your hands are wet.

■ Never plug the scanner into a multiplug power strip.

■ Never bundle, wrap, or tie the power cord around itself or another

object. Connect the power plug securely into the power outlet.

■ Use only the power cord and power plug provided with the scanner.

■ Never attempt to disassemble or modify the scanner.

■ Never use flammable aerosol products near the scanner.

■ Before you clean the scanner, turn the power OFF and disconnect

the power cord from the power outlet.

■ To clean the scanner’s exterior, use a firmly wrung cloth, moistened

slightly with water or mild detergent. Never use any type of volatile

solution, such as alcohol, benzene or paint thinner.

■ If you hear strange sounds, detect smoke or abnormal heat, sense

vibration, or smell odd odors around the scanner, turn OFF the

power switch immediately and disconnect the power cord from the

power outlet. Contact your local authorized Canon dealer or service

representative to have the scanner serviced.

■ Handle the scanner with care. Avoid shock and vibration to the

scanner caused by reckless handling. If you suspect the scanner

has been accidentally damaged, turn OFF the power switch

immediately and disconnect the power cord from the power outlet.

Contact your local authorized Canon dealer or service

representative to have the scanner serviced.

■ Before you move the scanner, always turn OFF the power and

disconnect the power cord from the power outlet.

■ This product emits low level magnetic flux. If you use a cardiac

pacemaker and feel abnormalities, please be away from this

product and consult your doctor.

CAUTION

■ To avoid damage to the scanner, never place the scanner on an

unstable or vibrating

surface. The scanner may tip or fall over,

causing injury.

■ To avoid overheating and causing a fire, never block the air vents on

the back of the scanner.

■ Keep all liquids, beverages, or any type of liquid, and clips, staples,

necklaces, or other metal objects away from the scanner. If you

accidentally spill liquid or drop a metal object into the scanner, turn

OFF the power immediately and disconnect the power cord from the

power outlet. Contact your local authorized Canon dealer or service

representative to have the scanner serviced.

■ Never install the scanner in humid or dusty locations. Doing so may

cause a fire or electrical shock.

■ Never place heavy objects on top of the scanner, as these objects

may tip or fall over, and cause injury.

9

■ When you remove the power cord, grip it by the power plug head.

Never attempt to disconnect the power cord from the power outlet

by pulling on the power cord. Doing so may damage or expose the

cord’s internal wiring, and cause a fire or electrical shock.

■ Keep the area around the power outlet clear of all obstacles so you

can disconnect the power cord easily at all times.

■ Never spill water or volatile solutions (alcohol, benzene, paint

thinner) into the scanner. Doing so may cause a fire or electrical

shock.

■ When the scanner is not being used for a long period of time,

disconnect the power cord from the power outlet.

■ Avoid wearing loose fitting clothing, dangling jewelry, long ties, or

long hair that could become entangled with moving parts, especially

the rollers that feed paper into the scanner. If such objects become

entangled, immediately disconnect the power plug from the power

outlet to stop the scanner.

■ Be careful when you are loading a document or clearing a paper

jam. It is possible that the paper edges may cut your fingers.

■ Do not open the Maintenance Cover while the scanner is operating.

Doing so may result in a malfunction or injury.

■ Do not touch the pins and contacts on the scanner’s connector with

your hands. Doing so may result in a malfunction.

■ Do not touch anything except the operation buttons when the jogger

is operating (CR-190i II/CR-190i II UV only) or documents are being

fed.

■ Do not turn the scanner upside down. The ink may leak from the ink

disposal tank.

Installation Location

For operation, maintenance, and ventilation, make sure that there is

enough space around the scanner, as shown in the illustration above.

Avoid placing the scanner in the following places. It may cause a

malfunction and adversely affect the scanner or your computer.

• Places exposed to direct sunlight

If installation in such places is unavoidable, provide a curtain or

similar object to shade the scanner.

• Places subject to dust and fumes

Dust and cigarette fumes adversely affect the components inside the

scanner.

• Near running water, a heat source, water vapor, or in an area, such

as a laboratory exposed to ammonia gas, paint thinner, or other

volatile chemicals

• Places subject to excessive vibration and shock

100 mm (3.9")

706 mm (27.8")

356 mm (14")

466 mm (18.3")

125 mm (5")

10

• Places subject to rapid changes in temperature or humidity

Condensation occurring inside the scanner may impair image

quality. Place the scanner in a room that is within the following range:

Room temperature: 10°C to 32.5°C (50°F to 90.5°F)

Relative humidity: 20% to 80% RH

Use the recommended operating environment for the ink cartridge

when using the imprinter.

• Near electronic equipment or heavy equipment that generates a

strong magnetic field, such as a speaker, TV, and radio

Power Supply

• Connect only to a power outlet of the rated voltage and power supply

frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz, depending on

your region).

• Make sure that the scanner is connected to an independent power

outlet. Do not plug the scanner into an outlet shared with another

device. If you use an extension cord, make sure that the extension

cord is rated for the current requirements of the scanner.

• If you are unsure of anything relating to the power supply, contact

your local authorized Canon dealer or service representative for

further information.

• Never place an object on top of the power cord or step on the power

cord.

• Never bundle the power cord or wrap the cord around an object,

such as a table leg.

• Do not tug on the power cord. When you remove the power cord, grip

it by the power plug head.

• Keep the area around the power outlet free of obstacles.

Moving the Scanner

When you move the CR-135i II/CR-190i II, hold it firmly with both hands

and carry it carefully. Do not hold the scanner by the Eject Stopper. The

scanner weighs approximately 8.0 kg (17.1 lb) or 8.4 kg (18.5 lb).

WARNING

When moving the scanner, be sure to turn OFF the power and

remove any cables. If the cables are not removed before moving

the scanner, you may damage the plugs or connector by forcibly

pulling them out.

11

Introduction to the CR-135i II/CR-190i II

This chapter describes the features of the CR-135i II/CR-190i II

scanner, what comes packaged in the box, and the names and

functions of parts on the scanner.

The Canon Check Reader CR-135i II/CR-190i II is a scanner with

magnetic heads that can read checks and other documents that are

printed with MICR (Magnetic Ink Character Recognition) compatible

fonts, and is capable of OCR (Optical Character Recognition).

Features

High-Speed Scanning (200 dpi American checks)

CR-135i II: 135 cpm

CR-190i II: 190 cpm

CR-135i II UV: 120 cpm (UV Scan mode)

CR-190i II UV: 160 cpm (UV Scan mode)

Supports Large Documents

Documents up to 108 mm x 245 mm (4.3" x 9.6") can be scanned.

High Durability

The scanner has a high durability of 24 million scans.

Compact Size

Supports Black-and-White (Binary) and Grayscale Output

Reads MICR Characters

A magnetic head is used to scan MICR characters.

Supports OCR (Optical Character Recognition)

Character images, such as E13B, OCR-A, OCR-B, and check writer are

recognized as characters by the OCR function.

Supports UV scanning (UV models only)

The CR-135i II UV/CR-190i II UV can scan images that are printed with

UV fluorescent ink. This function only scans the front side of

documents.

Easy to Maintain

Large Maintenance Covers make handling paper jams and cleaning

easy.

Jogger Mechanism Is Standard (CR-190i II/CR-190i II UV

only)

A jogger mechanism, which uses vibration to align documents, comes

standard equipped with the CR-190i II/CR-190i II UV.

Separation OFF Mode

You can scan the following documents:

• Thick documents

• Documents that contain two or more pages together as one

document

• Documents that have a rough surface

• Duplicate forms that have sticky edges

Paper Thickness Adjustment Mechanism

Adjust the Separation Roller gap to the thickness of the paper being

fed.

Features of the CR-135i II/CR-190i II

12

Three Eject Pockets and Automatic Sorting Mechanism

The scanner has three Eject Pockets and the documents are

automatically ejected to each pocket according to sort methods. The

scanner fits various scan operations using this mechanism.

Ultrasonic Double Feed Detection and Double Feed Detect

OFF Button (Scanning Utility for CR-135i/CR-190i)

The scanner detects double-fed documents using ultrasonic, and can

turn OFF the function with the Function Button.

Drop-Out Color

This function enables drop-out scanning of a specific color in the

document.

Imprinter Is Standard Equipment

An imprinter mechanism, which prints text (4 lines) or a bitmap on

documents as they are scanned, comes standard equipped with the

scanner. The imprinter’s ink cartridge is not included, and must be

purchased separately. (See “About the Ink Cartridge,” on p. 22.)

Eject Pocket Full Detection (Scanning Utility for CR-135i/

CR-190i)

Detects when any one of the three Eject Pockets is full and stops

scanning. This function is available only on CR-135i II/CR-190i II/CR-

190i II UV. (See “Scan Procedure,” on p. 33.)

Placing Additional Documents

You can place additional documents while the machine is scanning.

Replaceable rollers and ink disposal tank

You can replace the rollers (Pickup Roller, Feed Roller, and Separation

Roller) and the ink disposal tank.

Make sure that you have everything shown below. Check every item

you have removed from the box. If any items are missing, contact your

local authorized Canon dealer.

Packaging: What Is in the Box?

CR-135i II/CR-190i II

Setup Disc Power Cord

*1

Warranty Card

*2

USB Cable

*1 The power cord varies, according to the country of purchase.

*2 For the United States and Canada only.

Installation Guide

Operation & Maintenance Guide

13

This section describes the names and functions of each part. Before you connect the CR-135i II/CR-190i II, familiarize yourself with its parts and their

functions.

Front View

Part Names

Power Switch

Front Maintenance Cover

Open this cover to clear paper jams or to clean

the scanner.

Roller Cover

Operation Buttons

Ink Cartridge

Ink cartridge is not included. Purchase the ink cartridge

separately. (See “About the Ink Cartridge,” on p. 22.)

JOG: Uses vibration to align the documents. (Jogger)

This button is available only on the CR-190i II/

CR-190i II UV.

Function (F): You can assign this button to any function from

an application. When using the accompanying

Scanning Utility for CR-135i/CR-190i, switches the

double feed detection ON/OFF.

START: Starts scanning operations. Press and hold

this button during a paper jam to eject the

jammed document.

STOP: Stops scanning operations.

Scanner Unit

This unit scans the documents.

Magnetic Head for MICR

Reads MICR characters that have been printed with magnetic ink.

Built-in Nozzle Cleaning Pad

14

Back Maintenance Cover

Open this cover to clear paper jams or to clean the scanner.

Separation OFF Mode Button

Use this button when you want to scan the following documents (See

“Separation OFF Mode,” on p. 35.):

• Thick documents

• Documents that contain two or more pages together as one document

• Documents that have a rough surface

• Duplicate forms that have sticky edges

Adjustment Dial Cover

Top Cover

Adjustment Dial

Adjust the Separation Roller gap if feeding errors

occur too frequently. (See “Adjusting the

Separation Roller Gap,” on p. 56.)

Eject Stopper

Pull out the Eject Stopper to prevent

documents from falling off the output

tray.

Eject Pocket

Documents are separated with flappers

into three pockets. (See p. 34)

Scanner Unit

This unit scans the documents.

15

Rear View

CAUTION

To avoid overheating and causing a fire, never block the air vents on the

back of the scanner.

Connector

Units: millimeters (units in parenthesis are inches)

Ink Disposal Tank Pocket

Connector

Air Vent

Power Cord Connector

Connect the power cord provided with the

scanner to this connector.

USB Connector

Connect a Hi-Speed USB 2.0 compatible

cable. (See “USB Connections,” on p. 19.)

Exterior Dimensions

476 mm (18.7")

272 mm (10.7")

581 mm (22.9") (with the eject stopper open)

177 mm (7")

137 mm (5.4")

213.5 mm (8.4")

16

Preparation Before Use

This chapter describes how to prepare the scanner to scan

documents.

Perform the following steps to set up the CR-135i II/CR-190i II. Refer to

the section for each step for details about that step.

A Check your operating environment. (See “Checking Your

Operating Environment,” on p. 17.)

B Install the software. (See “Installing the Software,” on

p. 18.)

Install the Scanning Utility provided with the CR-135i II/CR-190i II.

C Connect the scanner to a computer. (See “Connecting

the Scanner to a Computer,” on p. 19.)

D Turn ON the power. (See “Turning ON the Power,” on

p. 20.)

E Automatically installing the device driver. (See p. 21.)

The device driver is installed automatically when Windows

recognizes the CR-135i II/CR-190i II.

IMPORTANT

• To have the device drivers installed automatically when the computer

recognizes the CR-135i II/CR-190i II, the software needs to be installed

before the CR-135i II/CR-190i II is connected to the computer.

• If you connect the computer and turn ON the CR-135i II/CR-190i II before

installing the software, the following wizard screen appears. If this

happens, click [Cancel], turn OFF the CR-135i II/CR-190i II, and then

install the software.

The following wizard screen is an example in Windows 7. When a similar

wizard screen appears in Windows 8.1/10, click [Cancel].

Setting Up the Scanner

Wizard Screen (Windows 7)

17

The following computer system requirements are recommended for

using the CR-135i II/CR-190i II.

Operating Systems:

• Microsoft Windows 7 (32/64bit) SP1 or later

• Microsoft Windows 8.1 (32/64bit)

• Microsoft Windows 10 (32/64bit)

• Microsoft Windows Server 2008 R2 Service Pack 1 or later

• Microsoft Windows Server 2012 R2

• Microsoft Windows Server 2016

• Microsoft Windows Server 2019

This is the environment as of December 2018.

For the latest software support information, go to the Products page on

the Canon website.

Specifications:

• CPU: Intel Core2 Duo 3.0 GHz or faster

• Memory: 1 GB or more

• USB 2.0 interface

Interface Cable

• Use the cable provided or a Hi-Speed USB 2.0 interface cable to

connect to the computer’s USB port.

IMPORTANT

• If you use the USB interface that was provided as standard with your

computer:

• Use the most recently available USB 2.0 driver provided by Microsoft.

Contact your local authorized Canon dealer for more detailed

information.

• Not all USB interfaces provided as standard with personal computers

are guaranteed. Contact your local authorized Canon dealer for more

detailed information.

• Scanning speeds are slower if your computer’s standard USB interface

is USB 1.1.

• You should use the USB cable originally bundled with the scanner or a

Hi-Speed USB 2.0 compatible cable.

• If the CPU, memory, interface card, and other specifications do not satisfy

the installation requirements, the scanning speed may be greatly reduced

and transmission may take longer.

• Even if the computer satisfies the system requirements, the scanning

speed may vary, depending on the specifications and operating

environment of the computer and the specified scan settings.

Checking Your Operating Environment

18

The following software applications are provided on the setup disc that

is packaged with the scanner. Make sure to open and read the

Readme.txt file on the setup disc before installing the software.

Scanning Utility

Canon Scanning Utility is an application that provides scanning, file

saving, image viewing, printing, and various other functions. A

dedicated scanner driver is installed after you install the utility

software.

Ranger

Ranger is an API software. For details, see “About the Ranger,” on

p. 26.

IMPORTANT

• The Scanning Utility includes a device driver so that Windows can

recognize the CR-135i II/CR-190i II. Be sure to install the Scanning Utility

before connecting the CR-135i II/CR-190i II to the computer.

• Some functions mentioned in this manual may not be operated in some

applications.

Installing the Scanning Utility

Follow the instructions below to install the Scanning Utility and the

dedicated driver.

NOTE

The dedicated scanner driver is installed after the Scanning Utility has been

installed.

A Turn ON your computer, and log on to Windows.

IMPORTANT

Be sure to log on as the Administrator.

B Insert the setup disc into the Disc drive.

This manual assumes that “D” is assigned to your Disc drive.

C Click [Start], and then click [All Programs].

The procedure in Windows 7/8.1/10 is different from the ones

described in this manual. Refer to the Windows 7/8.1/10 “Help

and Support Center” to select [Run].

Installing the Software

19

D Click [Accessories], and then click [Run].

E Enter “D:\SU190i\setup.exe” in the [Open] fields, and then

click [OK].

Installation starts.

F Follow the instructions on the screen to complete the

installation.

IMPORTANT

The computer may need to be restarted, after the installation, depending on

the operating system. If this is necessary, make sure to restart the computer.

The only way to connect the scanner to your computer is with a USB cable.

CAUTION

• Do not turn OFF the scanner or remove the interface cable when an

application is running.

• Turn OFF the computer and the scanner before changing the cable.

USB Connections

Connect the scanner and the computer with the USB cable provided

or a Hi-Speed USB 2.0 cable.

NOTE

Connect the type B plug (square) to the scanner and connect the type A plug

(flat) to the USB port on the computer.

Connecting the Scanner to a Computer

Type A Plug Type B Plug

USB Cable

USB Connector

20

Connecting the Power Cord

Connect the power cord.

Make sure to use only the power cord provided with the scanner.

WARNING

When connecting the power cord, follow these precautions. Failure to

do so may cause a fire or electrical shock.

• Never grasp the power plug when your hands are wet.

• Never plug the scanner into a multiplug power strip.

• Never bundle or tie the power cord around itself or another object.

Connect the power plug securely into the power outlet.

• Use only the power cord and power plug provided with the scanner.

•

Before you connect the power cord, make sure to turn OFF the power switch.

• Connect only to a power outlet of the rated voltage and power supply

frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz, depending on

your region).

• Do not plug the scanner into a power outlet shared with another

device. If you use an extension cord, make sure that the extension

cord is rated for the current requirements of the scanner.

Follow the procedures below to turn the scanner power ON and OFF.

Turning ON the Power

A To turn ON the scanner, press the Power Switch to the “ ”

position.

IMPORTANT

• When you turn ON the power, the power LED lights and remains lit.

• If the scanner does not work, or the power LED continues to flash, there is

a problem with the scanner. Turn OFF the power, and contact your local

authorized Canon dealer or service representative to have the scanner

serviced.

WARNING

If you hear strange sounds, detect smoke or abnormal heat, sense a

vibration, or smell odd odors around the scanner, turn OFF the power

immediately and disconnect the power cord from the power outlet.

Contact your local authorized Canon dealer or service representative to

have the scanner serviced.

Turning ON and OFF the Power

La pagina sta caricando ...

Canon imageFORMULA CR-190i II Manuale del proprietario

Questo manuale è adatto anche per

Canon imageFORMULA CR-190i II Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti