Epson TM-S2000 Series Technical Reference

Describes how to control the scanner and necessary information

when you develop applications.

Describes setup and installation of the product.

Describes how to handle the product.

Describes features and general specifications for the product.

Technical Reference Guide

Describes the interface and character code tables.

M00046102

Rev. C

Product Overview

Setup

Application Development Information

Handling

Appendix

2

Cautions

• No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form

or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior

written permission of Seiko Epson Corporation.

• The contents of this document are subject to change without notice. Please contact us for the latest

information.

• While every precaution has been taken in the preparation of this document, Seiko Epson Corpora-

tion assumes no responsibility for errors or omissions.

• Neither is any liability assumed for damages resulting from the use of the information contained

herein.

• Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third

parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of:

accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this

product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating

and maintenance instructions.

• Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of

any options or any consumable products other than those designated as Original Epson Products or

Epson Approved Products by Seiko Epson Corporation.

Trademarks

EEPSON is a registered trademark of Seiko Epson Corporation.

Exceed Your Vision is a registered trademark or trademark of Seiko Epson Corporation.

3

For Safety

Key to Symbols

The symbols in this manual are identified by their level of importance, as defined below. Read

the following carefully before handling the product.

WARNING

You must follow warnings carefully to avoid serious bodily injury.

CAUTION

Provides information that must be observed to prevent damage to the equipment or loss of

data.

 Possibility of sustaining physical injuries.

 Possibility of causing physical damage.

 Possibility of causing information loss.

Provides information that must be observed to avoid damage to your equipment or a

malfunction.

Provides important information and useful tips.

4

Warnings

WARNING

 To avoid risk of electric shock, do not set up this product or handle cables during

a thunderstorm.

 Never insert or disconnect the power plug with wet hands.

Doing so may result in severe shock.

 Handle the power cable with care.

Improper handling may lead to fire or electric shock.

 Do not modify or attempt to repair the cable.

 Do not place any heavy object on top of the cable.

 Avoid excessive bending, twisting, and pulling.

 Do not place the cable near heating equipment.

 Check that the plug is clean before plugging it in.

 Be sure to push the plug all the way in.

 Be sure to use the specified AC adapter.

Connection to an improper power source may cause fire or shock.

 Do not place multiple loads on the power outlet.

Overloading the outlet may lead to fire.

 Shut down your equipment immediately if it produces smoke, a strange odor, or

unusual noise.

Continued use may lead to fire. Immediately unplug the equipment and contact your

dealer or a Seiko Epson service center for advice.

 Never attempt to repair this product yourself.

Improper repair work can be dangerous.

 Never disassemble or modify this product.

Tampering with this product may result in injury or fire.

 Do not allow foreign matter to fall into the equipment.

Penetration by foreign objects may lead to fire.

 If water or other liquid spills into this equipment, do not continue to use it.

Continued use may lead to fire. Unplug the power cord immediately and contact your

dealer or a Seiko Epson service center for advice.

 Do not use aerosol sprayers containing flammable gas inside or around this

product.

Doing so may cause fire.

5

Cautions

Restriction of Use

When this product is used for applications requiring high reliability/safety such as

transportation devices related to aviation, rail, marine, automotive, etc.; disaster prevention

devices; various safety devices etc; or functional/precision

devices, etc., you should use this

product only after giving consideration to including fail-safes and redundancies into your

design to maintain safety and total system reliability. Because this product was not intended for

use in applications requiring extremely high reliability/safety such as aerospace equipment,

main communication equipment, nuclear power control equipment, or medical equipment

related to direct medical care, etc., please make your own judgment on this product’s suitability

after a f

ull evaluation.

CAUTION

 Do not connect cables in ways other than those mentioned in this manual.

Different connections may cause equipment damage or fire.

 Be sure to set this equipment on a firm, stable, horizontal surface.

The product may break or cause injury if it falls.

 Do not use this product in locations subject to high humidity or dust levels.

Excessive humidity and dust may cause equipment damage or fire.

 Do not place heavy objects on top of this product. Never stand or lean on this

product.

Equipment may fall or collapse, causing breakage and possible injury.

 Take care not to injure your fingers on the manual cutter

 When you remove printed paper

 When you perform other operations, such as loading/replacing roll paper

 Before leaving the product unused for an extended period, make sure the ink

cartridge is installed, turn the product off using the power button, and unplug the

product to ensure safety.

6

About this Manual

Aim of the Manual

This manual was created to provide information on development and design of scanner

applications for developers.

Manual Content

The manual is made up of the following sections:

Chapter 1

Product Overview

Chapter 2

Setup

Chapter 3

Application Development Information

Chapter 4

Handling

Appendix

Specifications of USB Interface

Character Code Tables

7

Contents

■ For Safety...............................................................................................................................3

Key to Symbols ....................................................................................................................................... 3

Warnings ................................................................................................................................................. 4

Cautions.................................................................................................................................................. 5

■ Restriction of Use...................................................................................................................5

■ About this Manual ................................................................................................................6

Aim of the Manual................................................................................................................................. 6

Manual Content .................................................................................................................................... 6

■ Contents ................................................................................................................................7

Product Overview ........................................................................10

■ Features ...............................................................................................................................10

■ Product Configuration........................................................................................................11

Color...................................................................................................................................................... 11

Attachments ........................................................................................................................................ 11

■ Part Names and Functions.................................................................................................12

Power Button ........................................................................................................................................ 13

Control Panel ....................................................................................................................................... 13

Connectors........................................................................................................................................... 15

■ Offline ..................................................................................................................................16

■ Processing Modes for Cut Sheet Paper ............................................................................17

High-Speed Mode ............................................................................................................................... 17

Confirmation Mode............................................................................................................................. 19

■ Selectable Functions for Processing Cut Sheet ...............................................................23

■ Error Status ...........................................................................................................................25

Automatically Recoverable Errors ..................................................................................................... 25

Recoverable Errors .............................................................................................................................. 26

Unrecoverable Errors ........................................................................................................................... 27

■ NV Memory (Non-Volatile Memory) ................................................................................28

NV Graphics Memory.......................................................................................................................... 28

User NV Memory .................................................................................................................................. 28

Memory Switches................................................................................................................................. 28

User-defined Page............................................................................................................................... 29

Maintenance Counter ........................................................................................................................ 29

■ Maintenance Counter........................................................................................................30

■ Product Specifications .......................................................................................................31

Printing Specifications ......................................................................................................................... 33

Character Specifications.................................................................................................................... 34

8

Scanner Specifications ........................................................................................................................35

MSR (Factory Option)...........................................................................................................................36

Paper Specifications ............................................................................................................................37

Printable Area.......................................................................................................................................38

Scannable Area ...................................................................................................................................39

MICR Readable Area ..........................................................................................................................41

Area for Electric Endorsement ............................................................................................................41

Environmental Conditions ...................................................................................................................42

Reliability................................................................................................................................................42

External Dimensions and Mass ............................................................................................................43

Setup .............................................................................................45

■ Flow of Setup ...................................................................................................................... 45

■ Installing the Product ......................................................................................................... 46

Important Notes on Installation ..........................................................................................................46

■ Connecting the Product to the Host Computer .............................................................. 47

■ Connecting the Power Supply Unit................................................................................... 48

■ Installing and Replacing the Ink Cartridge ..................................................................... 49

■ Setting the Memory Switches............................................................................................ 51

Functions ...............................................................................................................................................51

Application Development Information......................................53

■ Software .............................................................................................................................. 53

Operating Environment .......................................................................................................................53

Software for Windows ..........................................................................................................................54

Software for Linux .................................................................................................................................55

How to Get Drivers, Utilities, and Manuals .........................................................................................55

■ Setting/Checking Modes .................................................................................................. 56

Self-test Mode.......................................................................................................................................56

NV Graphics Print Mode......................................................................................................................57

Handling .......................................................................................58

■ Turning On/Off the Product ............................................................................................... 58

Turning On .............................................................................................................................................58

Turning Off .............................................................................................................................................58

■ Opening Covers ................................................................................................................. 59

Opening the Ink Cartridge Cover ......................................................................................................59

Opening the MICR Cover ...................................................................................................................59

9

Opening the Scanner Cover.............................................................................................................. 60

■ Processing Cut Sheet Paper ..............................................................................................61

Flow of Single Pass Processing............................................................................................................ 61

Important Notes on Processing Cut Sheet Paper ............................................................................ 61

Inserting Cut Sheet Paper ................................................................................................................... 62

Ejecting Cut Sheet Paper ................................................................................................................... 63

■ Scanning ID Cards..............................................................................................................64

■ Reading Magnetic Stripe Cards........................................................................................65

■ Cleaning..............................................................................................................................66

Cleaning the Ink-Jet Head ................................................................................................................. 66

Cleaning the MICR Head ................................................................................................................... 66

Cleaning the Scanner......................................................................................................................... 67

Cleaning the Product Case ............................................................................................................... 68

■ Troubleshooting ..................................................................................................................69

Error LED Is On or Flashing ................................................................................................................... 69

Paper or ID Card Is Jammed.............................................................................................................. 69

Printout Is Faint ..................................................................................................................................... 69

Reading/Scanning Is not Normal....................................................................................................... 69

■ Preparing for Transport .......................................................................................................70

Install the transportation cartridge .................................................................................................... 70

Pack the scanner................................................................................................................................. 70

Appendix......................................................................................71

■ Specifications of USB Interface .........................................................................................71

USB Interface (Type B) ......................................................................................................................... 71

Optional USB Interface (Type A) ........................................................................................................ 71

■ Character Code Tables .....................................................................................................72

Common to All Pages ......................................................................................................................... 72

Page 0 [PC437: USA, Standard Europe]............................................................................................73

Page 1 (Katakana).............................................................................................................................. 74

Page 2 (PC850: Multilingual) .............................................................................................................. 75

Page 3 (PC860: Portuguese) .............................................................................................................. 76

Page 4 (PC863: Canadian-French)................................................................................................... 77

Page 5 (PC865: Nordic) ...................................................................................................................... 78

Page 16 (WPC1252)............................................................................................................................. 79

Page 17 (PC866: Cyrillic #2)................................................................................................................ 80

Page 18 (PC852: Latin2)...................................................................................................................... 81

Page 19 (PC858: Euro) ..........................................................................................................

.............. 82

Page 255 (User-Defined Page) .......................................................................................................... 83

International Character Sets .............................................................................................................. 84

10

Product Overview

This chapter describes features and specifications of the TM-S2000MJ.

Features

This compact, full-scale, up-grade hybrid product integrates functions of printing, check

computerization, personal ID image reading, and magnetic card stripe reading (optional)

required mainly for reception work at ban ks.

The main features are as follows.

•Small-footprint

•Check endorsement, cut sheet paper (cut sheet receip

ts, cashier’s check) printing

Ink-jet printing of multiple line and high resolution with 360 nozzle and 180 dpi

•Check magnetic ink character reader (E13B, CMC7) (supported by the driver.)

•Capturing image on the face and back of cut sheet paper and personal ID (such as driver’s

license)

Capability in obtaining binary (only cut sheet paper is supported.), grayscale, color, and infrared light

source images

•Auto sheet feeder

•Double feed detection for cut sheet paper

•Function to judge improper insertion of checks

•IQA (Image Quality Assurance) (supported by the driver)

•OCR (Optional Character Recognition) (OCR-A font, OCR-B font, barcodes) (supported by the

driver)

•High-speed USB (USB 2.0 compliant) port

•Maintenance counter tha

t is convenient for remote maintenance

•Buzzer

•Low ink detection, notifications to request replacing the ink cartridge

•Paper separation using two exit pockets (supported by the two-pocket models only.)

•Magnetic stripe reader (factory option)

•USB-HUB (fac

tory option)

Chapter 1 Product Overview

11

1

Product Configuration

The TM-S2000MJ differs in function and equipment depending on the combinations of the

following specifications.

•Document processing speed: 110 dpm or 200 dpm

•Number of document exit pockets: 1 pocket or 2 pockets

•Whether or not the product has an MSR (Magnetic Stripe Reader) and USB (Type A)

connectors

dpm: documents per m

inute

Color

EDG (Epson Dark Gray)

Attachments

•USB cable

•2 dedicated ink cartridges (Model: SJIC18(K))

•AC cable*

•AC adapter

•Setup Guide

• User’s Manual

* May not be included depending on the product model.

Processing speed

Number of

document pockets

MSR

USB (Type A)

connectors

110 dpm 1 pocket Installed Installed

Not installed Not installed

2 pockets Installed Installed

Not installed Not installed

200 dpm 1 pocket Installed Installed

Not installed Not installed

2 pockets Installed Installed

Not installed Not installed

12

Part Names and Functions

Control panel

Connectors

Sub pocket

Main pocket

Pocket guide

Scanner cover

ASF guide

Scanner cover open lever

Power button

Ink cartridge cover

MICR cover open lever

MSR

MICR cover

Two-pocket model

MSR (factory option)-equipped model

(See "Control Panel" on page 13.)

(See

"Connectors" on page 15.)

Chapter 1 Product Overview

13

1

Power Button

Turns the product on or off.

Control Panel

Power LED (Green)

•Lights when the power supply is on.

•Flashes rapidly while some operations such as turning power on, ink charging, or cleaning,

are executed.

• Flashes slowly while turning power off.

•Goes out when the power supply is tu rned off.

Error LED (Orange)

•Lights when the product is offline (except during self-test and during print head cleaning).

•Flashes when an error occurs. (For details about the flash codes, see "Error Status" on page 25.)

•Goes out during regular operation (online).

Be sure not to turn off the product or open the covers while the Power LED is flashing.

(Power) LED

Error LED

Document LED

ID Card LED

Ink LED

Cleaning button

14

Document LED (Green)

•Lights when the product is ready to process cut sheet paper in the ASF or while the product is

processing cut sheet paper.

•Flashes when the product is waiting for cut sheet paper insertion.

•Goes out except for the cases above.

ID Card LED (Green)

•Lights when ID card is set and the product is ready to process it.

•Flashes when the product is waiting for ID card insertion or removal.

•Goes out except for the cases above.

Ink LED (Orange)

•Lights when no ink cartridge is installed or it is time to replace the ink cartridge.

•Flashes when ink is low.

•Goes out when the ink cartridge is installed and remaining ink is enough.

Cleaning button

Pressing this button for 3 seconds or more starts the ink-jet head cleaning. (See "Cleaning the Ink-

Jet Head" on page 66

.)

Chapter 1 Product Overview

15

1

Connectors

All cables are connected to the connector panel on the lower rear of the product.

•Power supply connector (

➀): Connects the power supply unit.

•USB connector (Type B) (➁): Connects the product with the host computer.

•USB connectors (Type A)* (

➂): Connects USB devices.

* Factory option

1

23

16

Offline

The TM-S2000MJ automatically goes offline under the following conditions:

•During initialization after:

Power on (including resetting with the interface)

Removal of error causes

•When any of the following covers are opened:

Ink cartridge cover

MICR cover

Scanner cover

•When no ink cartridge is installed

•When it is time to replace the ink cartridge

•During self-test

•During the ink-jet head cleaning

•When an error has occurred

•During macro command execution

For MSR equipped models, reading magnetic stripe card is possible, regardless of whether

the product is online or offline.

Chapter 1 Product Overview

17

1

Processing Modes for Cut Sheet Paper

The TM-S2000MJ has the following processing modes that are selectable with the driver in

accordance with how you want to use the product with cut sheet paper.

•High-speed mode

•Confirmation mode (with overlap/without overlap)

High-Speed Mode

This mode selects pockets and specifies whether to continue processing based on conditions

specified prior to scanning.

For detailed information about processing modes, see the TM-S2000MJ API Reference

Guide.

Fed from the ASF

Check for double feeding

MICR reading

Ink jet printing

Capturing image on both sides

Ejection of the document

Fed from the ASF

Check for double feeding

MICR reading

Fed from the ASF

Check for double feeding

MICR reading

Ink jet printing

Caputuring image on both sides

Ejection of the document

18

When ejecting into the sub pocket (only for two-pocket models)

When documents are sorted into the two ejection pockets, a document is fed backward to the

pocket switching position and then ejected into a pocket if the ejection pocket is required to be

switched and the document is long. In that case, the processing slows down.

Fed from the ASF

Check for double feeding

MICR reading

Ink jet printing

Capturing image on both sides

Backward paper feeding*

Switching of the pocket

Ejection of the document

Fed from the ASF

Check for double feeding

Ejection of the document

Fed from the ASF

Switching of the pockets

*: Occurs depending on some

conditions.

Chapter 1 Product Overview

19

1

Confirmation Mode

This mode selects pockets and specifies whether to continue processing according to commands

from the application for each scan.

Confirmation mode with overlap

The product starts feeding the next document while ejecting the current document into a pocket.

Fed from the ASF

Check for double feeding

MICR reading

Ink jet printing

Capturing image on both sides

Stop of paper feeding*

Ejection of the document

Fed from the ASF

Check for double feeding

Ejection of the document

Fed from the ASF

Stop of paper feeding*

* Waits for a command from the

application.

20

When ejecting into the sub pocket (only for two-pocket models)

When the two-pocket model receives a command to eject a document into a pocket, the

processing slows down because it feeds the document backward to the pocket switching

position and ejects it into a pocket.

Fed from the ASF

Check for double feeding

MICR reading

Ink jet printing

Capturing image on both sides

Stop of paper feeding*

Backward paper feeding*

Switching of the pockets

Ejection of the document

Fed from the ASF

Check for double feeding

Ejection of the document

Fed from the ASF

Switching of the pockets

1

2

*

1

Waits for a command from

the application.

*

2

Occurs depending on some

conditions.

La pagina sta caricando ...

Epson TM-S2000 Series Technical Reference

Epson TM-S2000 Series Technical Reference

in altre lingue

Documenti correlati

Altri documenti