E-flite EFL01150 Manuale del proprietario

Marca: E-flite

Modello: EFL01150

Categoria: Giocattoli telecomandati

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

A-10 Thunderbolt II

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

64mm Twin EDF

SAFE

Select Technology, Optional Flight Envelope Protection

A-10 64mm Twin EDF

Safety Precautions and Warnings

AGE RECOMMENDATION: Not for children under 14 years. This is not a toy.

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of

others.

• Always keep a safe distance in all directions around your model

to avoid collisions or injury. This model is controlled by a radio

signal subject to interference from many sources outside your

control. Interference can cause momentary loss of control.

• Always operate your model in open spaces away

from full-size vehicles, traf c and people.

• Always carefully follow the directions and warnings for this and any

optional support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything

electrical out of the reach of children.

• Always avoid water exposure to all equipment not speci cally designed

and protected for this purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as

it could cause serious injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set before  ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature,

visit www.horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high

probability of super cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product

correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this

Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children

without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon

Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the

manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

14+

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase

from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all

support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or

Spektrum technology.

Table of ContentsSpeci cations

If you own this product, you may be required to register with the FAA. For up-

to-date information on how to register with the FAA, please visit

https://registermyuas.faa.gov/. For additional assistance on regulations and

guidance on UAS usage, visit knowbeforeyou y.org/.

Transmitter Setup (BNF) ......................................................................4

Model Assembly .................................................................................4

PNP Receiver Selection and Installation ..............................................7

Battery Installation and ESC Arming ....................................................8

Center of Gravity (CG) .........................................................................8

Transmitter and Receiver Binding / Switchin ON and

OFF SAFE

Select ...............................................................................9

SAFE

Select Switch Designation ......................................................10

Using SAFE

Select With the DX6 and DX6e Transmitters

With a 6 Channel Aircraft ..................................................................10

Control Horn and Servo Arm Settings ................................................11

Control Surface Centering .................................................................11

Control Direction Test ........................................................................12

AS3X Control Direction Test ...............................................................13

In Flight Trimming .............................................................................13

Flying Tips and Repairs .....................................................................14

SAFE Select Flying Tips .....................................................................14

Post Flight ........................................................................................15

Power Components Service ..............................................................15

AS3X

System Trouble Shooting Guide .............................................16

Troubleshooting Guide .....................................................................16

Replacement Parts ............................................................................17

Recommended Parts .........................................................................17

Optional Parts ...................................................................................17

AMA National Model Aircraft Safety Code ..........................................18

Limited Warranty ..............................................................................19

Warranty and Service Contact Information ........................................19

FCC Information ................................................................................20

IC Information ...................................................................................20

Compliance Information for the European Union ................................21

Box Contents

Quick Start Information

Transmitter Setup

1. Blank (Acro) Model

2. Wing Type: 1 Aileron, 1 Flap

3. Servo Reversing: Gear Reversed, All Others

Normal

4. Travel Adjust (All Surfaces): 100%

Dual Rates*

High Rate Low Rate

Aileron

 = 11mm

 = 11mm

 = 8mm

 = 8mm

Elevator

 = 10mm

 = 8mm

 = 8mm

 = 8mm

Rudder

 = 12mm

 = 12mm

 = 8mm

 = 8mm

Flap Travel

Take-off  = 10mm Landing  = 23mm

EXPO

(Soft center)

High Rate Low Rate

Aileron 15% 10%

Elevator 10% 5%

Rudder 10% 5%

Center of Gravity (CG)

55-70mm back from the leading edge, measured at

the wing root

Flight Timer Setting 3.5 to 4 minutes

Motors: (2) 2840 - 2200Kv

Brushless motor

(EFL01192)

Included Included

Fan Unit: (2) 64mm

Ducted Fan Unit

(EFL9790)

Installed Installed

ESC: 40A Brushless ESC Twin motor set (EFL01190)

Stand alone BEC (EFL01191)

Installed Installed

Servos:

9g Servo Sub-Micro (SPMSA334) Installed Installed

Retracts: Nose Gear (EFLG347), Main Gear Left

(EFLG348) and Main Gear Right (EFLG348)

Installed Installed

Receiver: Spektrum

™

6-Channel Sport Receiver

(SPMAR636)

Installed

Required to

Complete

Recommended Battery: 3200-4000 mAh 22.2V 6S

IC5

™

30C Li-Po

Required to

Complete

Required to

Complete

Recommended Battery Charger:

6-cell Li-Po battery balancing charger

Required to

Complete

Required to

Complete

Recommended Transmitter:

Full-Range 2.4GHz with Spektrum

™

DSM2

/DSMX

technology with programmable mixing and adjustable

dual rates

Required to

Complete

Required to

Complete

80-85 oz

(2268-2410 g)

41.8 inches (1061mm)

45.2 inches (1149mm)

RECEIVER BIND INFORMATION

Channels

Frequency 2404 – 2476 MHz

Compatibility DSM2 and DSMX

340 sq/in

(21.9 sq/dm)

A-10 64mm Twin EDF

IMPORTANT: After you set up your model, always rebind the transmitter and

receiver to set the desired failsafe positions.

If your transmitter allows it, enable the throttle cut feature. Always engage

throttle cut before approaching the aircraft.

Dual Rates

Low rate is recommended for the initial  ights.

NOTICE: To ensure AS3X

technology functions properly, do not lower rate

values below 50%. If lower rates are desired, manually adjust the position of

the pushrods on the servo arm.

NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting

Guide for more information.

Expo

After  rst  ights, you may adjust expo in your transmitter.

Computerized Transmitter Setup

(DX6e

‡

, DX6

‡

, DX7, DX7S, DX8, DX8e, DX9, DX10t, DX18, DX20 and iX12)

Start all transmitter programming with a blank ACRO model (do a model

reset), then name the model.

Set Dual Rates to:

HIGH 100%

LOW 70%

Set Servo Travel to: 100%

DX7S

DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse Gear

6. Set FLAP SYSTEM: Choose Flap

NORM: -100% FLAP* 0% ELEV

Take-off: -10% FLAP* 10% ELEV

LAND: 70% FLAP* 12% ELEV

DX6e

‡

DX6

(Gen2)

‡

DX7

(Gen2)

DX8

(Gen2)

DX8e

DX9

DX10t

DX18

DX20

iX12

†

1. Go to the SYSTEM SETUP (Model Utilities)

†

2. Set MODEL TYPE: AIRPLANE

3. Set AIRCRAFT TYPE (Model Setup, Aircraft Type)

†

WING: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST (Model Adjust)

†

5. Set SERVO SETUP: Reverse Gear

6. Set FLAP SYSTEM:

SELECT SWITCH D:

POS 0: -100% FLAP* 0% ELEV

POS 1: -10% FLAP* 10% ELEV

POS 2: 70% FLAP* 12% ELEV

SPEED 2.0

†

Some of the terminology and function locations used in the iX12

programming may be slightly different than other Spektrum AirWare™

radios. The names given in parenthesis correspond to the iX12 programming

terminology. Consult your transmitter manual for speci c information about

programming your transmitter.

* Flap programming values may vary slightly. For your initial  ights use the

recommended  ap travel settings provided in the Flaps section and adjust the

 ap travel to your preference on subsequent  ights.

‡

The settings provided are for the DX6 and DX6e and do not allow for the use of a

SAFE Select switch. To use a SAFE Select switch on these systems see the section

for transmitter setup and operation information.

Horizontal Tail Installation

1. With the bottom of the fuselage facing up, connect the rudder and elevator

servo connectors and push the excess servo wire into the pocket.

2. Apply medium CA to all joining surfaces of the horizontal stabilizer, press

the horizontal stabilizer into place and allow to cure. Ensure the stabilizer is

perpendicular to the centerline of the fuselage.

Transmitter Setup (BNF)

Model Assembly

Vertical Fin Installation

1. Connect the rudder servo connector to the extension in the horizontal

stabilizer. Secure the connection with tape.

2. Apply the decal over the servo and servo wire as shown. Feed the excess servo

wire into the pocket at the end of the horizontal stabilizer.

3. Apply medium CA to all joining surfaces of the left vertical  n, press into

place and allow to cure. Ensure that the vertical  n is perpendicular to the

horizontal stabilizer.

4. Install the right vertical  n onto the opposite side of the horizontal tail

following the previous steps.

Model Assembly (Continued)

A-10 64mm Twin EDF

Wing Installation

1. Align and insert the main wing into the slot in the bottom of the fuselage.

2. Secure the wing into position using the included 4 screws (3x32mm) (A).

3. Disassemble in reverse order.

Pave Penny Pod Installation

1. Apply medium CA to joining surface of the Pave Penny pod.

2. Attach the Pave Penny pod to recess on the right side of the fuselage.

Model Assembly (Continued)

The recommended receiver for this aircraft is the Spektrum AR636. If you

choose to install a different receiver, ensure that it is at least a 6-channel full

range (sport) receiver. Refer to the manual of your chosen receiver for correct

installation and operation instructions.

AR636 Installation

1. Pull open the receiver hatch (A) to expose the receiver compartment. The

hatch is held in place magnetically.

2. Attach the appropriate control surfaces to the their respective ports on the

receiver using the table at the right.

3. Using double-sided servo tape, (not included) mount the receiver to the

 at area in the receiver compartment located on the bottom side of the

fuselage, as shown. The receiver should be mounted in the orientation

shown, parallel to the length of the fuselage, with the label facing up and

the servo ports facing the rear of the aircraft. The orientation of the receiver

is critical for all AS3X

and SAFE

technology setups.

NOTICE: You must set the orientation of the receiver using the Spektrum

programming software.

CAUTION: Incorrect installation of the receiver could cause a crash.

PNP Receiver Selection and Installation

1 = Throttle

2 = Aileron

3 = Elevator

4 = Rudder/Nose Wheel

5 = Retracts

6 = Flaps

Optional Scale Ordnance Installation

The included optional scale ordnance are easily installed and removed without

the use of tools.

A: The Mk. 84 Bombs are installed on the innermost wing mounting points.

B: The AGM-65 Maverick Missiles are installed on the  rst mounting points

outside the landing gear sponson.

C: The LAU-131 Rocket Pods are installed on the middle mounting points of

the outer wing panel.

D: The AIM-9 Sidewinder Missiles are installed on the outermost wing

mounting points.

To install the missiles:

1. Insert the tabs of the missiles in the enlarged end of the mounting

point slots.

2. Slide toward the back of the aircraft to lock the tabs in the slots.

TIP: There is a left and right to each pylon. The notation can be found on the

base of the pylon.

To remove the missiles, slide them forward and pull the tabs out of the

mounting slots.

A-10 64mm Twin EDF

Battery Installation and ESC Arming

Battery Selection

We recommend a 3200mAh 6S 22.2V Smart 30C (SPMX32006S30)

LiPo battery with EC5™ or IC5™ connector for standard operation. If using

a different battery, the battery should be of similar capacity, dimensions

and weight to  t in the fuselage. Always be sure the model balances at the

recommended CG with the battery chosen.

1. Lower the throttle to the lowest setting.

2. Power on the transmitter and wait 5 seconds.

3. Apply the loop side (soft side) of the hook and loop tape to the bottom of

your battery.

4. Slide the canopy latch back and lift the back of the canopy to remove.

5. Install the fully charged battery in the battery compartment as shown.

See the Adjusting the Center of Gravity instructions for more information.

6. Secure the  ight battery with the hook and loop strap.

7. Connect the ESC to the battery power lead EC5™ or IC5™ connector,

noting the correct polarity. The ESC will emit two sets of audible tones in

succession indicating the programming status.

• The  rst set of tones indicates the number of cells in the connected LiPo

battery pack.

6 rapid tones = 6

• The second set of tones indicates the brake status. One tone

indicates brake “ON” and two tones indicates brake “OFF”.

NOTICE: Connecting the battery to the ESC with incorrect polarity will

damage the ESC and void the warranty.

8. The ESC is now ready for use.*

9. Reinstall the canopy hatch.

* While additional programming of the ESC is not necessary to operate your

aircraft, programming options are available. Visit www.horizonhobby.com for

complete instructions on programming the included ESC.

Center of Gravity (CG)

The center of gravity location is measured from the leading edge of the wing at

the root with the landing gear down. The CG location is adjusted by moving the

battery pack forward or backward in the battery compartment.

NOTICE: Install the battery in the aircraft, but do not connect the battery to

the ESC while checking the CG. Personal injury may result.

55-70mm

back from the leading edge

at the wing root with the

gear down.

Transmitter and Receiver Binding / Switchin ON and OFF SAFE

Select

Switching OFF SAFE Select Binding Sequence

Install Bind Plug

RX in Bind Mode

Bind TX to RX

Remove Bind Plug

This product requires an approved Spektrum

™

DSM2

/DSMX

compatible

transmitter. Visit www.bindn y.com for a complete list of approved

transmitters.

The aircraft has an optional SAFE Select feature, which can be switched ON or

OFF easily by binding in a speci c manner as described below.

IMPORTANT: Before binding a transmitter, read the Transmitter Setup section

of this manual to ensure that your transmitter is properly programmed for this

aircraft.

Bind Plug Installation

BIND PLUG

Binding Procedure / Switching OFF SAFE Select

IMPORTANT: The included AR636 receiver has been programmed for

operation speci cally for this aircraft. Refer to the receiver manual for correct

setup if the receiver is replaced or is used in another aircraft.

CAUTION: When using a Futaba

transmitter with a Spektrum DSM

module, you must reverse the throttle channel and rebind. Refer to your

Spektrum module manual for binding and failsafe instructions. Refer to your

Futaba transmitter manual for instructions on reversing the throttle channel.

1. Make sure the transmitter is powered off.

2. Move the transmitter controls to neutral ( ight controls: rudder, elevators

and ailerons) or to low positions (throttle, throttle trim). *

3. Install a bind plug in the receiver bind port.

4. Place the aircraft level on its wheels, then connect the  ight battery to

the ESC. The ESC will produce a series of sounds. Six  at tones followed

immediately by two ascending tones con rm that the LVC is set correctly for

the ESC.

The orange bind LED on the receiver will begin to  ash rapidly. DO

NOT remove the bind plug at this time.

5. Take three steps away from the aircraft /receiver and then power ON the

transmitter while holding the transmitter bind button or switch. Refer to

your transmitter’s manual for speci c binding instructions.

IMPORTANT: Do not to point the transmitter’s antenna directly at the

receiver while binding.

IMPORTANT: Keep away from large metal objects while binding.

6. The receiver is bound to the transmitter when the orange bind light on the

receiver stays orange. The ESC will produce a series of sounds. Six  at tones

followed immediately by two ascending tones. The tones indicate the ESC is

armed, provided the throttle stick and throttle trim are low enough to trigger

arming.

7. Remove the bind plug from the bind port.

IMPORTANT: Once bound, the receiver will retain its bind settings for that

transmitter until it has been intentionally changed, even when power is

cycled ON and OFF. Repeat the binding process as necessary.

SAFE Select OFF Indication

Every time the receiver is powered ON the surfaces will cycle back and forth

once to indicate that SAFE Select has been switched OFF.

The throttle will not arm if the transmitter’s throttle control is not put at the

lowest position. If problems are encountered, follow the binding instructions

and refer to the transmitter troubleshooting guide for other instructions. If

needed, contact the appropriate Horizon Product Support of ce.

Binding Procedure / Switching ON SAFE Select

IMPORTANT: The included AR636 receiver has been programmed for

operation speci cally for this aircraft. Refer to the receiver manual for

correct setup if the receiver is replaced or is used in another aircraft.

CAUTION: When using a Futaba

transmitter with a Spektrum DSM

module, you must reverse the throttle channel and rebind. Refer to your

Spektrum module manual for binding and failsafe instructions. Refer to your

Futaba transmitter manual for instructions on reversing the throttle channel.

1. Make sure the transmitter is powered off.

2. Move the transmitter controls to neutral ( ight controls: rudder, elevators

and ailerons) or to low positions (throttle, throttle trim).*

3. Install a bind plug in the receiver bind port.

4. Place the aircraft level on its wheels, then connect the  ight battery to the ESC. The

ESC will produce a series of sounds. Six  at tones followed immediately by two

ascending tones con rm that the LVC is set correctly for the ESC. The orange bind

LED on the receiver will begin to  ash rapidly.

5. Remove the bind plug from the bind port.

6. Take three steps away from the aircraft /receiver and then power ON the

transmitter while holding the transmitter bind button or switch. Refer to

your transmitter’s manual for speci c binding instructions.

IMPORTANT: Do not to point the transmitter’s antenna directly at the

receiver while binding.

IMPORTANT: Keep away from large metal objects while binding.

7. The receiver is bound to the transmitter when the orange bind light on the

receiver stays orange. The ESC will produce a series of sounds. Six  at

tones followed immediately by two ascending tones. The tones indicate

the ESC is armed, provided the throttle stick and throttle trim are low

enough to trigger arming.

IMPORTANT: Once bound, the receiver will retain its bind settings for that

transmitter until it has been intentionally changed, even when power is

cycled ON and OFF. Repeat the binding process as necessary.

SAFE Select ON Indication

Every time the receiver is powered ON the surfaces will cycle back and forth

twice with a slight pause at neutral position to indicate that SAFE Select is

switched ON.

The throttle will not arm if the transmitter’s throttle control is not put at the

lowest position. If problems are encountered, follow the binding instructions

and refer to the transmitter troubleshooting guide for other instructions. If

needed, contact the appropriate Horizon Product Support of ce.

* Failsafe

If the receiver loses transmitter communication, the failsafe will activate. When activated, failsafe moves the throttle channel to its preset

failsafe position (low throttle) that was set during binding. All other channels move collectively and actively to place the aircraft in a slow descending left turn.

Install Bind Plug

Remove Bind Plug

RX in Bind Mode

Bind TX to RX

Switching ON SAFE Select Binding Sequence

A-10 64mm Twin EDF

SAFE

Select technology can be easily assigned to any open switch (2 or 3

position) on your transmitter. With this feature, you have the  exibility to enable

or disable the technology while in  ight.

IMPORTANT: Before assigning your desired switch, ensure that the travel for

that channel is set at 100% in both directions and the aileron, elevator, rudder

and throttle are all on high rate with the travel at 100%. Turn throttle hold OFF

if it is programmed in the transmitter.

CAUTION: Keep all body parts well clear of the rotor, intakes and

exhaust tube and keep the aircraft securely restrained in case of

accidental throttle activation.

Assigning a switch

1. Bind the aircraft correctly to activate SAFE Select. This will allow the

system to be assigned to a switch.

2. Hold both transmitter sticks to the inside bottom corners and toggle the

desired switch 5 times (1 toggle = full up and down) to assign that switch.

The control surfaces of the aircraft will move, indicating the switch has

been selected.

Repeat the process to assign a different switch or to deactivate the current

switch if desired.

TIP: SAFE Select is assignable on any unused Channels 5–9.

The SAFE Select switch must be assigned to the Flap switch (switch D)

BEFORE proceeding to the Transmitter Setup and should start from a blank

(reset) model. Failure to assign the SAFE switch prior to programming the other

model functions may prevent the SAFE switch from assigning correctly. Users

of the DX6 and DX6e will have the SAFE Select functionality linked to the  aps.

The values given in the Transmitter Setup table turn SAFE ON when the  aps

are fully deployed. SAFE is OFF when the  aps are not fully deployed.

IMPORTANT: When programming the Flap System function in the transmitter

setup of the DX6 and DX6e, set the Speed value to Norm. Adding any delay to

the deployment of the  aps will also delay the activation of SAFE.

DX6 and DX6e Transmitter Setup for SAFE

Select Operation

Start all transmitter programming with a blank ACRO model (do a model

reset), then name the model.

Set Dual Rates to:

HIGH 100%

LOW 70%

Set Servo Travel to: 100%

DX6e

DX6

(Gen2)

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set AIRCRAFT TYPE:

WING: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse Gear

See the SAFE

Select Switch Designation section BEFORE setting

the  ap values.

6. Set FLAP SYSTEM:

SELECT SWITCH D:

POS 0: -100% FLAP 0% ELEV

POS 1: -10% FLAP 10% ELEV

POS 2: 70% FLAP 12% ELEV

SAFE

Select Switch Designation

Mode 1 and 2 transmitters

100%

X 5

Using SAFE

Select With the DX6 and DX6e Transmitters With a 6 Channel Aircraft

Control Surface Centering

Control Horn and Servo Arm Settings

After assembly and transmitter setup, con rm that the control surfaces are

centered.

NOTICE: The model must be powered up and bound to the transmitter in

AS3X mode, with the throttle left at zero. When enabled, SAFE mode is active

at power up. AS3X mode is activated when the throttle is raised above 25%

for the  rst time after being powered on.

It is normal for the control surfaces to respond to aircraft movement if the

aircraft is in AS3X or SAFE modes.

1. Verify the trims and subtrims on your transmitter are zero

2. Power up the model in AS3X mode and leave the throttle at zero

NOTICE: Be aware of the pushrod bottoming out in the ball linkage. Do not

thread the pushrod too far into the ball link or the pushrod will damage the ball

link and protrude into the area needed for the control ball.

3. Center the rudders in line with the vertical stabilizers. If adjustment is

required, turn the ball link on the linkage to change the length between the

servo arm and the control horn until the rudders are straight.

4. Center the ailerons by aligning the outboard end of the aileron with the

trailing edge of the wing tip. Adjust the linkage length as in step 3 as

necessary.

5. Center the elevators with the horizontal stabilizer. Ensuring that each

elevator is aligned with one another. Adjust the linkage length as in step 3 as

necessary.

The table to the right shows the factory settings for the control horns and servo

arms. Fly the aircraft at factory settings before making changes.

NOTICE: If control throws are changed from the factory settings, the AR636

gain values may need to be adjusted. Refer to the Spektrum AR636 manual

for adjustment of gain values.

After  ying, you may choose to adjust the linkage positions for the desired

control response. See the table to the right.

Control Horns Servo Arms

Elevator

Ailerons

Flaps

Rudder

Nose Wheel

More control throw Less control throw

1. 2.

A-10 64mm Twin EDF

Control Direction Test

Transmitter

command

Control Surface

Response

ElevatorAileronRudderFlaps

Switch on the transmitter and connect the battery. Use the transmitter to

operate the aileron, elevator and rudder controls. View the aircraft from the rear

when checking the control directions.

Elevators

1. Pull the elevator stick back. The elevators should move up, which will cause

the aircraft to pitch up.

2. Push the elevator stick forward. The elevators should move down, which

will cause the aircraft to pitch down.

Ailerons

1. Move the aileron stick to the left. The Left aileron should move up and the

Right aileron down, which will cause the aircraft to bank left.

2. Move the aileron stick to the right. The right aileron should move up and the

left aileron down, which will cause the aircraft to bank right.

Rudder

1. Move the rudder stick to the left. The rudders should move to the left, which

will cause the aircraft to yaw left.

2. Move the rudder stick to the right. The rudders should move to the right,

which will cause the aircraft to yaw right.

AS3X Control Direction Test

Aircraft

Movement

AS3X Reaction

ElevatorAileronRudder

This test ensures that the AS3X

control system is functioning properly.

Assemble the aircraft and bind your transmitter to the receiver before

performing this test.

1. Raise the throttle to any setting above 25%, then lower the throttle to

activate AS3X technology.

CAUTION: Keep all body parts, hair and loose clothing away from the

fan intake, as these items could become entangled.

2. Move the entire aircraft as shown and ensure the control surfaces move in

the direction indicated in the graphic. If the control surfaces do not respond

as shown, do not  y the aircraft. Refer to the receiver manual for more

information.

Once the AS3X system is active, control surfaces may move rapidly. This is

normal. AS3X remains active until the battery is disconnected.

During your  rst  ight, trim the aircraft for level  ight at 3/4 throttle with the

gear up. Make small trim adjustments with your transmitter’s trim switches to

straighten the aircraft’s  ight path.

After adjusting trim do not touch the control sticks for 3 seconds. This allows the

receiver to learn the correct settings to optimize AS3X performance.

Failure to do so could affect  ight performance.

After landing, adjust the linkages mechanically to account for trim changes and

then reset the trims to neutral. Ensure the aircraft will  y straight and level with

no trim or sub-trim.

In Flight Trimming

3 Seconds

A-10 64mm Twin EDF

Flying Tips and Repairs

Consult local laws and ordinances before choosing a  ying location.

Range Check your Radio System

Before you  y, range check the radio system. Refer to your speci c transmitter

instruction manual for range test information.

Takeoff

Place the aircraft in position for takeoff (facing into the wind). Select low rates

for  rst takeoff and gradually increase the throttle to full and steer with the

nose wheel. Allow the model to accelerate to  ying speed, then pull back gently

on the elevator and climb to a comfortable altitude.

Flying

Always choose a wide-open space for  ying. Due to the higher speeds of this

aircraft, it does require more room to  y than average foam models. It is ideal

for you to  y at a sanctioned  ying  eld. If you are not  ying at an approved

site, always avoid  ying near houses, trees, wires and buildings. You should

also be careful to avoid  ying in areas where there are many people, such as

busy parks, schoolyards, or soccer  elds.

Landing

For your  rst few  ights with the recommended battery pack (SPMX32006S30),

set your transmitter timer or a stopwatch to 3 minutes, 30 seconds (3:30), then

land. Adjust your timer for longer or shorter  ights once you have  own the

model.

If at any time the motor pulses, land the aircraft immediately and recharge

the  ight battery. See the Low Voltage Cutoff (LVC) section for more details on

maximizing battery health and run time.

Turn the aircraft into the wind, reduce the throttle and extend the landing

gear and Flaps. The  aps will allow the aircraft to slow to a more manageable

landing speed while still maintaining lift. Elevator trim may be necessary

to maintain level  ight with the addition of  aps. Use the throttle during the

landing approach to control the rate of descent. Keep the wings level and the

aircraft pointed into the wind. As you approach the threshold of the runway and

approximately 1 meter altitude, decrease the throttle and begin your  are by

easing back on the elevator. Continue back pressure on the elevator to bring

the aircraft down gently on the runway.

NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to

do so could result in extra damage to the airframe, as well as damage to the

ESC and motor.

NOTICE: After any impact, always ensure the receiver is secure in the

fuselage. If you replace the receiver, install the new receiver in the same

orientation as the original receiver or damage may result.

NOTICE: Crash damage is not covered under warranty.

NOTICE: When you are  nished  ying, never leave the aircraft in direct

sunlight or in a hot, enclosed area such as a car. Doing so can damage the

aircraft.

Low Voltage Cutoff (LVC)

When a Li-Po battery is discharged below 3V per cell, it will not hold a charge.

The ESC protects the  ight battery from over-discharge using Low Voltage

Cutoff (LVC). Before the battery charge decreases too much, LVC removes

power supplied to the motor. Power to the motor pulses, showing that some

battery power is reserved for  ight control and safe landing. If the motors pulse

in  ight, land immediately and recharge the battery.

Disconnect and remove the Li-Po battery from the aircraft after use to prevent

trickle discharge. Charge your Li-Po battery to about half capacity before

storage.

During storage, make sure the battery charge does not fall below 3V per cell.

LVC does not prevent the battery from over-discharge during storage.

NOTICE: Repeated  ying to LVC will damage the battery.

Tip: Monitor your aircraft battery’s voltage before and after  ying by using

a Li-Po cell voltage checker (XBC100 Smart Battery Checker & Servo Driver

(SPMXBC100), sold separately).

Oscillation

Once the AS3X system is active (after advancing the throttle for the  rst time),

the control surfaces will react to aircraft movement. In some  ight conditions

oscillation may occur (the aircraft rocks back and forth on one axis due to

overcontrol). If oscillation occurs, refer to the Troubleshooting Guide for more

information.

Repairs

Thanks to the EPO foam material in this aircraft, repairs to the foam can be

made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts

are not repairable, see the Replacement Parts List for ordering by item number.

NOTICE: Use of CA accelerator on your aircraft can damage paint. DO NOT

handle the aircraft until accelerator fully dries.

SAFE Select Flying Tips

When  ying in SAFE Select mode the aircraft will return to level  ight any time

the aileron and elevator controls are at neutral. Applying aileron or elevator

control will cause the airplane to bank, climb or dive, and the amount the stick

is moved will determine the attitude the airplane  ies. Holding full control will

push the aircraft to the pre-determined bank and roll limits but it will not go

past those angles.

When  ying with SAFE Select it is normal to hold the control stick de ected

with moderate aileron input when  ying through a turn. To  y smoothly with

SAFE Select avoid making frequent control changes and don’t attempt to

correct for minor deviations. With SAFE Select, holding deliberate control inputs

will command the aircraft to  y at a speci c angle and the model will make all

corrections to maintain that  ight attitude.

Return the elevator and aileron controls to neutral before switching from SAFE

Select mode to AS3X mode. If you do not neutralize controls when switching

into AS3X mode, the control inputs used for SAFE Select mode will be

excessive for AS3X mode and the aircraft will react immediately.

Differences between SAFE Select and AS3X modes

This section is generally accurate but does not take into account  ight speed,

battery charge status, and many other limiting factors.

• In SAFE Select mode the aircraft will self level when the control

stick is neutralized. In AS3X mode the aircraft will continue to  y

at its present attitude when the control stick is neutralized.

• In SAFE Select mode holding a small amount of control will result in

the model banking or pitching to a moderate angle and remaining at

that angle as long as the control stick doesn’t move. In AS3X mode

holding a small amount of control will result in the model continuing to

pitch or roll at a slow rate as long as the control stick doesn’t move.

• In SAFE Select mode holding full control will result in the airplane

banking or pitching to the predetermined limits and the aircraft

will keep  ying at that attitude as long as the control stick is fully

de ected. In AS3X mode holding full control will result in the aircraft

pitching or rolling as fast as possible, and it will continue to rapidly

change attitude as long as the control stick is fully de ected.

CAUTION: Always disconnect the  ight battery before performing

service on any of the power system components.

Disassembly

1. Remove the 4 screws (3 x 10mm) (A) from the bottom of the engine nacelle

and pull the top half of the nacelle (B) up to expose fan unit (C).

2. Remove the 2 screws (3 x 8mm) (D) from the fan unit tabs.

3. Pull the fan unit out of the nacelle and disconnect the motor leads from

the ESC.

4. Remove the spinner cone (E) from the fan by removing the screw (3 x

10mm) (F) from the motor shaft adapter.

5. Use a wrench to remove the rotor nut (G) and washer (H).

6. Slide the fan rotor (I) off of the motor shaft (J) and motor shaft

adapter (K).

7. Remove the 4 screws (2.5 x 6mm) (L) to remove the motor from the fan

shroud (M).

8. Disconnect the ESC from the throttle channel of the receiver. and

disconnect the BEC from BEC input.

9. The ESC is held in place by friction between the nacelle body and the

fuselage. Remove the ESC’s by removing the 6 screws (3 x 10mm) from the

nacelle body and carefully pulling the ESC by the motor connection wires,

through the fuselage and out of the nacelle body opening.

Assembly

• Assemble in reverse order.

• Correctly align and connect the motor wire colors with the ESC wires.

• Ensure the front of the rotor is installed facing the nose of the aircraft.

• A wrench is required to tighten the nut on the rotor and collet.

• Ensure the spinner is fully seated on the rotor and

the screw is tight for safe operation.

• Ensure no wiring is pinched by any of the power components.

Post Flight

Disconnect the  ight battery from the ESC (Required for Safety and

battery life).

2 Power OFF the transmitter.

3 Remove the  ight battery from the aircraft.

4 Recharge the  ight battery.

5 Repair or replace all damaged parts.

6 Store the  ight battery apart from the aircraft and monitor the battery charge.

Make note of the  ight conditions and  ight plan results, planning for

future  ights.

Power Components Service

A-10 64mm Twin EDF

Troubleshooting Guide

AS3X

System Trouble Shooting Guide

Problem Possible Cause Solution

Oscillation

Damaged rotor or nose cone Replace rotor or nose cone

Imbalanced rotor Balance the rotor

Motor vibration Replace parts or correctly align fan unit or other parts and tighten fasteners as needed

Loose receiver Align and secure receiver in fuselage

Loose aircraft controls Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface)

Worn parts Replace worn parts (especially rotor, nose cone, or servo)

Irregular servo movement Replace servo

Inconsistent  ight

performance

Trim is not at neutral If you adjust trim more than 8 clicks, adjust the ball link to remove trim

Sub-Trim is not at neutral No Sub-Trim is allowed. Adjust the servo linkage

Aircraft was not kept immobile for 5

seconds after battery connection

With the throttle stick in lowest position. Disconnect battery, then reconnect battery and keep

the aircraft still for 5 seconds

Incorrect response

to the AS3X Control

Direction Test

Incorrect direction settings in the

receiver, which can cause a crash

DO NOT  y. Correct the direction settings (refer to the receiver manual), then  y

Problem Possible Cause Solution

Aircraft will

not respond

to throttle but

responds to other

controls

Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting

Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater

Throttle channel is reversed Reverse throttle channel on transmitter

Motor disconnected from ESC Make sure motor is connected to the ESC

Excessive

rotor noise

or Excessive

vibration

Damaged rotor, nose cone, collet or motor Replace damaged parts

Rotor is out of balance Balance or replace rotor

Rotor cone screw is too loose Tighten the rotor cone screw

Reduced  ight

time or aircraft

underpowered

Flight battery charge is low Completely recharge  ight battery

Flight battery damaged Replace  ight battery and follow  ight battery instructions

Flight conditions may be too cold Make sure battery is not cold before use (Do not apply heat to the battery)

Battery capacity too low for flight conditions Replace battery or use a larger capacity battery

Aircraft will not

Bind (during

binding) to

transmitter

Transmitter too near aircraft during binding process

Move powered transmitter a few feet from aircraft, disconnect and reconnect

 ight battery to aircraft

Aircraft or transmitter is too close to large metal

object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt binding again

The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter

Flight battery/transmitter battery charge is too low Replace/recharge batteries

Bind switch or button not held long enough during

bind process

Power off transmitter and repeat bind process. Hold transmitter bind

button or switch until receiver is bound

Aircraft will not

connect (after

binding) to

transmitter

Transmitter too near aircraft during connecting process

Move powered transmitter a few feet from aircraft, disconnect and reconnect  ight battery to

aircraft

Aircraft or transmitter is too close to large metal

object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt connecting again

Bind plug left installed in bind port Rebind transmitter to the aircraft and remove the bind plug before cycling power

Aircraft bound to different model memory

(ModelMatch

radios only)

Select correct model memory on transmitter

Flight battery/Transmitter battery charge is too low Replace/recharge batteries

Transmitter may have been bound to a different

aircraft using different DSM protocol

Bind aircraft to transmitter

Control surface

does not move

Control surface, control horn, linkage or servo damage Replace or repair damaged parts and adjust controls

Wire damaged or connections loose Do a check of wires and connections, connect or replace as needed

Transmitter is not bound correctly or the incorrect

airplanes was selected

Re-bind or select correct airplanes in transmitter

Flight battery charge is low Fully recharge  ight battery

BEC (Battery Elimination Circuit) of the ESC is damaged Replace BEC

Controls reversed Transmitter settings are reversed

Perform the Control Direction Test and adjust the controls on transmitter

appropriately

Motor power

pulses then

motor loses

power

ESC uses default soft Low Voltage Cutoff (LVC) Recharge  ight battery or replace battery that is no longer performing

Weather conditions might be too cold Postpone flight until weather is warmer

Battery is old, worn out, or damaged Replace battery

Battery C rating might be too small Use recommended battery

Replacement Parts

Recommended Parts

Part # Description

EFL01176 Wing: A-10 64mm EDF

EFL01177 Fuselage: A-10 64mm EDF

EFL01178 Horizontal Stab: A-10 64mm EDF

EFL01179 Fins/Rudders: A-10 64mm EDF

EFL01180 Canopy/Hatch: A-10 64mm EDF

EFL01181 Nacelle Assembly: A-10 64mm EDF

EFL01182 Linkage Set:A-10 64mm EDF

EFL01183 Wheel Set: A-10 64mm EDF

EFL01184 Screw Set: A-10 64mm EDF

EFL01185 Gear Door Set: A-10 64mm EDF

EFL01186 Decal Set: A-10 64mm EDF

EFL01187 Control Horn Set: A-10 64mm EDF

EFL01188 Armament Set: A-10 64mm EDF

EFL01189 LED Set: A-10 64mm EDF

EFL01190 ESC-40A Set: A-10 64mm EDF

EFL01191 BEC 5A: A-10 64mm EDF

EFL01192 Motor: 64mm EDF 2840-2200KV

EFL9790 Ducted Fan: 11-Blade 64mm EDF Unit

EFLG345 Nose Gear Strut: A-10 64mm EDF

EFLG346 Main Strut Set: A-10 64mm EDF

EFLG347 E-Retract Nose: A-10 64mm EDF

EFLG348 E-Retract Main: A-10 64mm EDF

EFLG349 Retract Pin Set: A-10 64mm EDF

SPMAR636 AR636 6-Ch AS3X Sport Receiver

SPMSA334 Servo: 9g Sub-Micro Plastic Dig

Part # Description

SPMX32006S30 3200mAh 6S 22.2V Smart 30C; IC5

SPMX40006S50 4000mAh 6S 22.2V 50C Smart LiPo IC5

EFLB40006S30 4000mAh 6S 22.2V 30C LiPo, 12AWG EC3

EFLB32006S30 3200mAh 6S 22.2V 30CLiPo, 12AWG EC3

EFLAEC509 EC3 to EC5 adapter

SPMR8100 DX8e 8CH Transmitter Only

DYNC3016 Passport P2 2Port AC/DC MultiCharger

SPMXC1000 Smart S1200 DC Charger, 1x200W

Optional Parts

Part # Description

EFLA111 LiPo Cell Voltage Checker

SPM6716 Spektrum DSMR Transmitter Case

SPM6722 Spektrum Single Aircraft TX Case

SPMR12000 iX12 12 Channel Transmitter Only

SPMR8000 DX8 Transmitter Only MD2

SPMR9910 DX9 Black Transmitter Only MD2

SPMXBC100 SMART Battery & Servo Tester

SPMXC1000 Smart S1200 DC Charger, 1x200W

SPMXC1010 Smart S2100 AC Charger, 2X100W

DYNC2050 Prophet Sport 4 X 100W AC/DC Charger

DYNC3017 Passport P4 AC/DC 4-Port Multicharger

SPMXC10201 30A 540W Power Supply

ONXP40006S30 Onyx 22.2V 4000mAh 6S 30C LiPo battery, EC5

SPMX32006S100

Spektrum 22.2V 3200mAh 6S 100C Smart LiPo

Battery, IC3

SPMXCA507

Adapter: IC3 Battery / IC5 Device, 4”/100mm Wire

10 AWG

A-10 64mm Twin EDF

AMA National Model Aircraft Safety Code

Effective January 1, 2014

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable of sustained  ight

in the atmosphere. It may not exceed limitations of this code and is intended

exclusively for sport, recreation, education and/or competition. All model  ights

must be conducted in accordance with this safety code and any additional

rules speci c to the  ying site.

1. Model aircraft will not be  own:

(a) In a careless or reckless manner.

(b) At a location where model aircraft activities are prohibited.

2. M odel aircraft pilots will:

(a) Yield the right of way to all man carrying aircraft.

(b) See and avoid all aircraft and a spotter must be used when appropriate.

(AMA Document #540-D.)

three (3) miles of an airport, without notifying the airport operator.

(d) Not interfere with operations and traf c patterns at any airport, heliport

or seaplane base except where there is a mixed use agreement.

(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless

in compliance with the AMA Large Model Aircraft program. (AMA

Document 520-A.)

(f) Ensure the aircraft is identi ed with the name and address or AMA

number of the owner on the inside or af xed to the outside of the model

aircraft. (This does not apply to model aircraft  own indoors).

(g) Not operate aircraft with metal-blade propellers or with gaseous boosts

except for helicopters operated under the provisions of AMA Document

#555.

(h) Not operate model aircraft while under the in uence of alcohol or while

using any drug which could adversely affect the pilot’s ability to safely

control the model.

(i) Not operate model aircraft carrying pyrotechnic devices which explode

or burn, or any device which propels a projectile or drops any object that

creates a hazard to persons or property.

Exceptions:

• Free Flight fuses or devices that burn producing smoke and are

securely attached to the model aircraft during  ight.

• Rocket motors (using solid propellant) up to a G-series size may be

used provided they remain attached to the model during  ight. Model

rockets may be  own in accordance with the National Model Rocketry

Safety Code but may not be launched from model aircraft.

• Of cially designated AMA Air Show Teams (AST) are authorized to use

devices and practices as de ned within the Team AMA Program Docu-

ment (AMA Document #718).

(j) Not operate a turbine-powered aircraft, unless in compliance with the

AMA turbine regulations. (AMA Document #510-A).

3. Model aircraft will not be  own in AMA sanctioned events, air shows or

model demonstrations unless:

(a) The aircraft, control system and pilot skills have successfully

demonstrated all maneuvers intended or anticipated prior to the speci c

event.

(b) An inexperienced pilot is assisted by an experienced pilot.

4. When and where required by rule, helmets must be properly worn and

fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or

comply with comparable standards.

B. RADIO CONTROL

1. All pilots shall avoid  ying directly over unprotected people, vessels,

vehicles or structures and shall avoid endangerment of life and property of

others.

2. A successful radio equipment ground-range check in accordance with

manufacturer’s recommendations will be completed before the  rst  ight of

a new or repaired model aircraft.

3. At all  ying sites a safety line(s) must be established in front of which all

 ying takes place (AMA Document #706.)

(a) Only personnel associated with  ying the model aircraft are allowed at

or in front of the safety line.

(b) At air shows or demonstrations, a straight safety line must be

established.

(d) Intentional  ying behind the safety line is prohibited.

4. RC model aircraft must use the radio-control frequencies currently allowed

by the Federal Communications Commission (FCC). Only individuals

properly licensed by the FCC are authorized to operate equipment on

Amateur Band frequencies.

5. RC model aircraft will not operate within three (3) miles of any pre-existing

 ying site without a frequency-management agreement (AMA Documents

#922 and #923.)

6. With the exception of events  own under of cial AMA Competition

Regulations, excluding takeoff and landing, no powered model may be

 own outdoors closer than 25 feet to any individual, except for the pilot and

the pilot’s helper(s) located at the  ight line.

7. Under no circumstances may a pilot or other person touch a model aircraft

in  ight while it is still under power, except to divert it from striking an

individual.

8. RC night  ying requires a lighting system providing the pilot with a clear

view of the model’s attitude and orientation at all times. Hand-held

illumination systems are inadequate for night  ying operations.

9. The pilot of a RC model aircraft shall:

(a) Maintain control during the entire  ight, maintaining visual contact

without enhancement other than by corrective lenses prescribed for the

pilot.

(b) Fly using the assistance of a camera or First-Person View (FPV) only in

accordance with the procedures outlined in AMA Document #550.

accordance with the procedures outlined in AMA Document #560.

Please see your local or regional modeling association’s guidelines for

proper, safe operation of your model aircraft.

Limited Warranty

Warranty and Service Contact Information

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product

purchased (the “Product”) will be free from defects in materials and workmanship

at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii)

damage due to acts of God, accident, misuse, abuse, negligence, commercial use,

or due to improper use, installation, operation or maintenance, (iii) modi cation of

or to any part of the Product, (iv) attempted service by anyone other than a Horizon

Hobby authorized service center, (v) Product not purchased from an authorized

Horizon dealer, (vi) Product not compliant with applicable technical regulations, or

(vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY

ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE

REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that

Horizon will, at its option, either (i) service, or (ii) replace, any Product determined

by Horizon to be defective. Horizon reserves the right to inspect any and all

Product(s) involved in a warranty claim. Service or replacement decisions are

at the sole discretion of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS

THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS

BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR

ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of

Horizon exceed the individual price of the Product on which liability is asserted. As

Horizon has no control over use, setup,  nal assembly, modi cation or misuse, no

liability shall be assumed nor accepted for any resulting damage or injury. By the

act of use, setup or assembly, the user accepts all resulting liability. If you as the

purchaser or user are not prepared to accept the liability associated with the use

of the Product, purchaser is advised to return the Product immediately in new and

unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to con ict of law

principals). This warranty gives you speci c legal rights, and you may also have

other rights which vary from state to state. Horizon reserves the right to change

or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support

or service. Once assembly, setup or use of the Product has been started, you

must contact your local distributor or Horizon directly. This will enable Horizon

to better answer your questions and service you in the event that you may need

any assistance. For questions or assistance, please visit our website at www.

horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone

number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country

you live and use the Product in, please use the Horizon Online Service Request

submission process found on our website or call Horizon to obtain a Return

Merchandise Authorization (RMA) number. Pack the Product securely using a

shipping carton. Please note that original boxes may be included, but are not

designed to withstand the rigors of shipping without additional protection. Ship

via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at

our facility. An Online Service Request is available at http://www.horizonhobby.

com/content/service-center_render-service-center. If you do not have internet

access, please contact Horizon Product Support to obtain a RMA number along

with instructions for submitting your product for service. When calling Horizon, you

will be asked to provide your complete name, street address, email address and

phone number where you can be reached during business hours. When sending

product into Horizon, please include your RMA number, a list of the included items,

and a brief summary of the problem. A copy of your original sales receipt must

be included for warranty consideration. Be sure your name, address, and RMA

number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue

with a LiPo battery, please contact the appropriate Horizon Product

Support of ce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your

Product will be serviced or replaced free of charge. Service or replacement

decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without noti cation or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without noti cation. Service

estimates are available upon request. You must include this request with your item

submitted for service. Non-warranty service estimates will be billed a minimum

of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts

money orders and cashier’s checks, as well as Visa, MasterCard, American

Express, and Discover cards. By submitting any item to Horizon for service, you

are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the coun-

try of use and ownership. If received, a non-compliant Product will not

be serviced. Further, the sender will be responsible for arranging return

shipment of the un-serviced Product, through a carrier of the sender’s

choice and at the sender’s expense. Horizon will hold non-compliant

Product for a period of 60days from noti cation, after which it will be

discarded.

10/15

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd

Champaign, IL 61822

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

European Union

Horizon Technischer Service service@horizonhobby.eu

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

A-10 64mm Twin EDF

IC Information

FCC Information

CAN ICES-3 (B)/NMB-3(B)

IC: 6157A-AMRX21

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the

device.

FCC ID: BRWDASRX21

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received,including interference that may cause undesired operation.

CAUTION: Changes or modi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable

regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Supplier’s Declaration of Conformity

EFL A-10 BNF BASIC AND PNP (EFL01150 and EFL01175)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: changes or modi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd., Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

La pagina sta caricando ...