Haier HAIPSJ64MC Manuale utente

HAIER

HAIPSJ64MC

ENGLISH

Instruction Manual For Induction Hob

ITALIANO

Manuale di istruzioni per piano di cottura ad induzione

POLSKI

Instrukcja obsługi płyty indukcyjnej

FRANÇAIS

Manuel d’utilisation de la table de cuisson à induction

ESPAÑOL

Manual de instrucciones de la encimera de inducción

DEUTSCH

Bedienungsanleitung für Induktionskochfeld

Návod na obsluhu indukčnej varnej dosky

SLOVENČINA

Návod k obsluze indukční varné desky

ČEŠTINA

Uputstvo za upotrebu indukcione ploče

SRPSKI

Manual de instruções para placa de indução

PORTUGUÊS





ENGLISH

Preci Probe: Important Safety Notes – Please read this carefully

before use :

- This product is exclusive for hob appliances. It should only be used

as described in this User Manual.

- This product is not intended for use by persons with ages 12 and

under.

- Probe can work in this range of temperature: 10 °C to an internal

maximum temperature of 100°C of the metal part. Ceramic part can

reach 350°C.

- There is a built-in Overheat alert in the Preci Probe APP to prevent

the overheating of Preci Probe. When the measured temperature is

higher than 80°C or 176°F, the Overheat alert will be triggered. Take

out Preci Probe from the heat source with gloves as soon as possible.

- Do not use Preci Probe in another appliance except for the induction

hob.

- Do not use Preci Probe in a microwave oven.

- Clean the Preci Probe before each use.

- Preci Probe can be cleaned and washed but do not immerse it long

in water . Do not put in dishwasher.

- DO NOT TOUCH Preci Probe WITH BARE HANDS JUST AFTER

COOKING. Always wear oven gloves to remove Preci Probe from the

food after cooking.

- It is required to insert Preci Probe properly into the food during

cooking. For the use of Preci Probe with liquid food, we recommend

the use of the ladle provided. Do not expose the metal part of Preci

Probe to the heat generated by the appliance.

- The supplier will not be liable for any damage of Preci Probe due to

misuse of the device.

• DO NOT use the Preci Probe inside frying oil.

• When you use the griddle, the metallic part of Preci Probe must not

touch it.

• DO NOT Insert the Preci Probe in an insulated material like foil.

• DO NOT use the Preci Probe over 110°C

• When you choose from the hOn APP the recipe with the Preci Probe

this need to be near the hob.

• Before each use please assure the Preci Probe is fully charged.

• Clean carefully the ceramic cap of the Preci Probe after using it.



Haier



ENGLISH

Haier



1. Max. 1500/2000 W zone

2. Max. 1500/2000 W zone

3. Max. 1500/2000 W zone

4. Max. 1500/2000 W zone

5. Glass plate

6. Control panel

1. Heating zone power controls

3. Timer control

5. ON/OFF control

4. Keylock control

2. " Cook with me" Function control

1

2

3

4

5

1

2

3

4

5



ENGLISH

4

6

 The controls respond to touch, so you don’t need to apply any pressure.

 Use the ball of your finger, not its tip.

 You will hear a beep each time a touch is registered.

 Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.

Even a thin film of water may make the controls difficult to operate.

• Only use cookware with a base suitable for induction cooking.

Look for the induction symbol on the packaging or on the bottom

of the pan.

• You can check whether your cookware is suitable by carrying out a magnet test.

Move a magnet towards the base of the pan. If it is attracted, the pan is suitable

for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2. If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper

without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone.

Use pans whose diameter is as large as the graphic of the zone selected. Using a pot a slightly wider energy will be

used at its maximum efficiency. If you use smaller pot efficiency could be less than expected. Pot less than 140 mm

could be undetected by the hob. Always centre your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

Touch Controls

Choosing the right Cookware



How to use

Touch the ON/OFF control for three seconds. After power on, the

buzzer beeps once, all displays show “–” or “– –”, indicating that the

induction hob has entered the state of standby mode.

Place a suitable pan on the cooking zone that you wish to use.

• Make sure the bottom of the pan and the surface of the cooking

zone are clean and dry.

Touching the heating zone slider control , and a indicator next to the

key will flash.

Select a heat setting by touching the slider control

• If you don’t choose a heat setting within 1 minute, the Induction

hob will automatically switch off. You will need to start again at step 1.

• You can modify the heat setting at any time during cooking.

If the display flashes alternately with the heat setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centered on the cooking zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically disappear after 1 minute if no suitable pan is placed on it.

Start cooking



ENGLISH

power up

power down

Touching the heating zone selection control that you wish to

switch off.

the display shows “0”.

Turn the whole cooktop off by touching the ON/OFF control.

Beware of hot surfaces

H will show which cooking zone is hot to touch. It will

disappear when the surface has cooled down to a safe

temperature. It can also be used as an energy saving function

if you want to heat further pans, use the hotplate that is still

hot.

Activate the boost function

Touching the heating zone slider control

Touching the slider to “B”. Make sure the display shows “b”.

Cancel the Boost function

Touching the heating zone slider control that you wish to cancel

the boost function.

the display shows “0”.

Finish cooking

Using the Boost function

Turn the cooking zone off by touching the slider to “0”. Make sure



 You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones

on).

 When the controls are locked, all the controls except the ON/OFF control are disabled.

When the hob is in the lock mode, all the controls are disable except the ON/OFF , you can always turn the induction

hob off with the ON/OFF control in an emergency, but you shall unlock the hob first in the next operation.

 You can pause the heating instead of shutting the hob off.

 When entering the Pause mode, all the controls except the ON/OFF control are disabled.

To enter pause mode

Short touch the Timer “ ” and Timer ”

” at the same

time.

All the indicator will show “ 11“

To exit pause mode

Short touch the Timer “ ” and Timer ”

” at the same time.

When the hob is in the pause mode, all the controls are disable except the ON/OFF

,

you can always turn the

induction hob off with the ON/OFF control in an emergency. The hob will shut down after 10min if you don’t exit the

pause mode.

 it is possible to set a maximum power absorption level for the induction hob, choosing up to different power

ranges.

 induction hobs are able to limit themselves automatically in order to work at lower power level, to avoid the risk of

overloading.

 The function can work in any cooking zone.

 The cooking zone returns to its original setting after 5 minutes.

 If the original heat setting equals 0, it will return to 9 after 5 minutes.

Locking the Controls

Pause Mode

Power Management Function

The timer indicator will show “ Lo ”

To lock the controls

To unlock the controls

Touch and hold the lock control for a

while.

Touch and hold the lock control for a while.



ENGLISH

.

The timer indicator will show “ P5“ which means power

To switch to another level

press +/- of the timer

or

There are 5 power levels, from “P1” to “p5”. The timer

indicator will show one of them.

“P1” : the maximum power is 2.5Kw.

“P2” : the maximum power is 3.5Kw.

“P3” : the maximum power is 4.5Kw.

“P4” : the maximum power is 5.5Kw.

Confirmation and Exit Power Management Function

”

for confirmation.

Then the hob will be turned off.

You can use the timer in two different ways:

 You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is

up.

 You can set it to turn one or more cooking zones off after the set time is up.

The timer of maximum is 99min.

Timer control

”

and Timer ”

“P5” : the maximum power is max power of the hob.

Turn on the hob, then Press at the same time the KEY

level 5。The default mode is on max power of the hob.

Lock and Time r ”

To enter Power Management Function

Press at the same time Key Lock



a) Using the Timer as a Minute Minder

If you are not selecting any cooking zone

Make sure the cooktop is turned on.

Note: you can use the minute minder even if you’re not selecting any

cooking zone.

Touch “+” the controls of the timer. The minder

indicator will start flashing and “10” will show

in the timer display.

Set the time by touching the “-” or “+” control

of the timer

Hint: Touch the “-” or “+” control of the timer

once to decrease or increase by 1 minute.

Touch and hold the “-” or “+” control of the timer to decrease or

increase by 10 minutes.

When the time is set, it will begin to count down

immediately. The display will show the remaining

time and the timer indicator will flash for 5 seconds.

Buzzer will beep for 30 seconds and the timer

indicator shows “- - “ when the setting time finished.

b) Setting the timer to turn one or more cooking zones off

Set one zone

Touching the heating zone slider control

Set the time by touching the or control of the timer

Hint: Touch the “-“ or “+” control of the timer

once will decrease or increase by 1 minute.

Touch and hold the ”-“ or “+”control of the timer

will decrease or increase by 10 minutes.

When the time is set, it will begin to count down immediately. The display

will show the remaining time and the timer indicator flash for 5 seconds.

NOTE: The red dot next to power level indicator will illuminate

indicating that zone is selected.



ENGLISH

When cooking timer expires, the corresponding cooking zone will be

switched off automatically.

Other cooking zone will keep operating if they are turned on previously.

set more zones:

The steps for setting more zones are similar to the steps of setting one zone;

When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on.

The minute display shows the min. timer. The dot of the corresponding zone flashes.

The shown as below:

(set to 15 minutes)

(set to 45 minutes)

Once the countdown timer expires, the corresponding zone will

switch off. Then it will show the new min. timer and the dot of

corresponding zone will flash.

The shown as right:

(set to 30 minutes)

Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.

c) Cancel the timer

Touching the heating zone slider control that you want to cancel

the timer

Touch and hold the timer control “ - ”, the timer decreases to “00”

and the timer is cancelled.

Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to

turn off your cooking. The default working times for various power levels are shown in the below table:

Power level

1 2 3 4 5 6 7 8 9

Default working timer (hour) 8 8 8 4 4 4 2 2 2

When the pot is removed, the induction hob can stop heating immediately and the hob automatically switch off after 2

minutes.

People with a heart pace maker should consult with their doctor before using this unit.

Default working times



To make the pairing between Hob and APP use the following process:

When wi-fi ON: one dot will appear on the right side of the LED

When WIFI OFF: No dot will appear.

a. WIRELESS PARAMETERS

Technology Wi-Fi BLE NFC

Standard

IEEE 802.11b/n/g

Bluetooth v4.2, BR/EDR, BLE /

Frequency Band(s) [MHz] 2402-2480 2402-2480 /

Maximum Power [mW] 1500 1500 /

When the hob receives the command from the app, the hob will beep for

2 times and blink for one second to indicate that the instructions have

been received.

Choose from the hOn App recipes menu or special programs menu.

Follow step by step the indications on the App and when you have

finished send the parameters to the hob that will cook for you.

Press 4 seconds the "Cook with me" button on the hob. Once the 4 seconds have passed, the digit of the TIMER starts

to blink with PA written on it and starts the pairing process. Now follow the instructions from the App.

First of all, you should download HOn and install to your portable device. Then enroll your induction hob following

the instructions directly from the App"

press 4 seconds

How to set " Cook with me" Function

" Cook with me" function

If you want to get out of "Cook with me" function change the power

level of the zone.



ENGLISH

Preci Probe model ET180

Preci Probe & Ladle

Intelligent Wireless Food Thermometer

Thank you for purchasing Haier Preci Probe. Please note it works only with Haier induction hob and before

using it please read the following instruction and safety notes included in the user manual.

Introduction

Preci Probe is a wireless food thermometer that gives home chefs real-time status inside the food to

avoid undercook or overcook disasters and ensuring the perfect result every time. It connects directly to

the product. Details and the real-time status of the food can be read from your phone, giving you the best

result at your fingertips. For further information on pairing and use tips, please refer to Induction user

manual

Getting Start

1. Ceramic Cap

2. Recommended immersion range

3. Sensor

4. Ladle with different position of

Preci Probe

Ladle

Use the ladle with the probe to stir food during your cooking.

- Clean the ladle before the first use.

- Do not use the ladle on an open flame.

- Do not cut the ladle.

- Do not put the ladle in direct contact with the hot accessible parts of the hob.

- Tolerated temperature range : -40 °C + 220°C

Charge the Preci Probe before using

• Put Preci Probe into the charger and close the cover.

• Connect the charger to a USB power source, such as USB adapter or USB

socket of PC/notebook with the USB cable. The charger may not be working

properly with power bank because of its auto switch-off function

• LED of the charger will turn on and is flashing during charging. It will turn

off when Preci Probe is fully charged.

1

2

3

4

By placing the CE mark on the appliance, we are conﬁrming compliance to all relevant European

safety, health ande environmental requirements which are applicable in legisla�on for this product.



Preci Probe model ET180

Pair the Preci Probe with the induction hob

x

Cooking Methods with the Preci Probe

Preci Probe as thermomether

Set in the hOn App the target temperature you want to reach, insert the Preci Probe inside the food or with

its accessory inside liquids and you will see the temperature raising from the app until reaching the target

temperature.

It will help you to accurately maintain the temperature for all kind of food.

You cannot use it when the Assisted Cooking function operates.

Assisted Cooking͗͞ŽŽŬǁŝƚŚŵĞ͟ĨƵŶĐƚŝŽŶ

Choose from the hOn App recipes or special programs, follow step by step the preparation and then the

hob will automatically set the parameters for the chosen cooking method.

Sous Vide

Type of cooking in which the food is placed in a vacuum bag and cooked in a low temperature water bath.

The

food prepared in this way will be more juicy and tender and will keep the nutritional properties intact,

making them healthier and tastier.

Go on the hOn App select the category of food, select this type of cooking, insert the bas with the food in

the pot with water and the induction hob will set the correct cooking temperature for a perfect result.

Grill

Select the category of food from the hOn App, select this type of cooking and the induction hob will

automatically brig the grill to the correct temperature in a predetermined time.

Simmering

The simmering function is ideal for cooking sauces, stews, braised dishes and all preparations with an

average long cooking time.

The automatic function you find on the hOn App will gently bring the food to a slightly boiling

temperature, keeping it for all the duration of cooking.

,ĞƌĞďǇ͕ĂŶĚǇ,ŽŽǀĞƌ'ƌŽƵƉ^ƌůĚĞĐůĂƌĞƐƚŚĂƚƚŚĞƌĂĚŝŽĞƋƵŝƉŵĞŶƚŝƐŝŶĐŽŵƉůŝĂŶĐĞǁŝƚŚŝƌĞĐƟǀĞ

ϮϬϭϰͬϱϯͬh͘dŚĞĨƵůůƚĞǆƚŽĨƚŚĞhĚĞĐůĂƌĂƟŽŶŽĨĐŽŶĨŽƌŵŝƚǇŝƐĂǀĂŝůĂďůĞĂƚƚŚĞĨŽůůŽǁŝŶŐŝŶƚĞƌŶĞƚ

ĂĚĚƌĞƐƐ͗ǁǁǁ͘ĐĂŶĚǇͲŐƌŽƵƉ͘ĐŽŵ

dĞĐŚŶŽůŽŐǇ

^ƚĂŶĚĂƌĚ

&ĞƌƋƵĞŶĐǇĂŶĚ;ƐͿ΀D,ǌ΁

DĂǆŝŵƵŵWŽǁĞƌ΀ŵt΁

>

dϰ͘Ϭ

ϮϰϬϬD,ǌͲϮϰϴϬD,ǌ

Ϯ͘ϱŵt;ϰĚŵͿ

EN-17

ENGLISH

Make sure that your hob is turned on and your Preci Probe is fully charged

Open the hOn APP on your portable device







The hob display will indicate the name of the Preci Probe (for example “1A”)



When using the app if the probe is under 20% of charge the Timer display will

indicate "CH"

•

Preci Probe model ET180

Steaming

With the steaming function you can steam food such as vegetables, meat or fish in pots equipped with a

steamer basket. Steam cooking is faster than boiling, as it is not immersed in a liquid it disperses less

nutrients contained in the food and preserves its vitamin content, improving its taste and structure which

will be more compact and pleasant.

Support

If necessary, contact the authorized service center





ENGLISH

Selection of cooking vessels

You may have a number of different cooking vessels

1. This induction hob can identify a variety of cooking vessels, which you can test by

one of the following methods:

Place the vessel on the cooking zone. If the corresponding cooking zone displays a

power level, then the vessel is suitable. If “U” flashes, then the vessel is not

suitable for use with the induction hob.

2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for

use with the induction hob.

NB: The base of the vessel must contain magnetic material.

It must have flat bottom with a diameter according to the table 1 below.

3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless

steel but compatible with induction

4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range

of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table 1, pots

may not be detected

According to the dimension of the zone you can use pots of different diameters as picture

below:

Iron oil frying

Stainless steel

Iron pan

Iron kettle

Enamel

stainless steel

kettle

Enamel cooking

utesil

Iron plate



5. If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a sufficient

temperature for cooking.

6. If the ferromagnetic area is not homogeneous, but presents others material such as

aluminum this may affect the heating up and the pan detection.

If the base of the pan is similar to the pictures below the pan could be not detected.

The base diameter of induction cookware

Cooking zone

1 & 2 140

140

180

1803 & 4

Minimum Maximum

The above may vary according to the size of the pan and the material it is made from.

La pagina sta caricando ...

Haier HAIPSJ64MC Manuale utente

Haier HAIPSJ64MC Manuale utente

in altre lingue

Documenti correlati

Altri documenti