IEI Technology S24M Manuale utente

S19M/S24M Marine Monitor

Page i

User Manual

S19M/S24M

MODEL:

19”/24” Marine Monitor with AC and DC Redundant Power,

Projected Capacitive Touchscreen, IP 66 Compliant

Front Panel and IP 22 Compliant Rear Cover

Rev. 1.00 – November 27, 2015

User Manual

S19M/S24M Marine Monitor

Page ii

Revision

Date Version Changes

November 27, 2015 1.00 Initial release

S19M/S24M Marine Monitor

Page iii

Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

S19M/S24M Marine Monitor

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the

equipment or result in personal injury. Warnings should be taken

seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of

losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical

information. These messages should be read carefully as any directions

or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without

taking care.

S19M/S24M Marine Monitor

Page v

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 OVERVIEW.................................................................................................................. 2

1.2 MODEL VARIATIONS ................................................................................................... 2

1.3 FEATURES................................................................................................................... 3

1.4 FRONT PANEL............................................................................................................. 3

1.4.1 Display Control Buttons..................................................................................... 4

1.5 BOTTOM PANEL.......................................................................................................... 4

1.6 REAR PANEL............................................................................................................... 5

1.7 SYSTEM SPECIFICATIONS............................................................................................ 6

1.8 DIMENSIONS............................................................................................................... 9

2 UNPACKING................................................................................................................11

2.1 ANTI-STATIC PRECAUTIONS...................................................................................... 12

2.2 UNPACKING PRECAUTIONS....................................................................................... 12

2.3 PACKING LIST........................................................................................................... 13

2.4 OPTIONAL ITEMS...................................................................................................... 14

3 INSTALLATION ......................................................................................................... 15

3.1 INSTALLATION PRECAUTIONS................................................................................... 16

3.2 MOUNTING THE MONITOR........................................................................................ 16

3.2.1 Panel Mounting................................................................................................ 17

3.2.2 Stand Mounting................................................................................................ 19

3.3 I/O INTERFACES ....................................................................................................... 20

3.3.1 BNC Video Input and Output ........................................................................... 20

3.3.2 Buzzer............................................................................................................... 20

3.3.3 DVI Inputs........................................................................................................ 21

3.3.4 Power Inputs.................................................................................................... 21

3.3.5 RJ-45 for Remote Control................................................................................ 22

3.3.6 RS-232 for Remote Control.............................................................................. 22

3.3.7 RS-422/485 for Remote Control....................................................................... 23

3.3.8 USB for Touchscreen........................................................................................ 23

 
 
S19M/S24M Marine Monitor
Page vi 
3.3.9 VGA Inputs....................................................................................................... 24 
3.3.10 VGA Output.................................................................................................... 24 
3.4 TURNING ON/OFF THE MARINE MONITOR ............................................................... 25 
4 ON-SCREEN DISPLAY (OSD) CONTROLS........................................................... 26 
4.1 OSD CONTROL BUTTONS......................................................................................... 27 
4.2 OSD MENU STRUCTURE AND OPTIONS.................................................................... 28 
5 IEI MONITOR REMOTE APPLICATION.............................................................. 31 
5.1 OVERVIEW................................................................................................................ 32 
5.2 LAUNCHING THE IEI MONITOR REMOTE APPLICATION ............................................ 32 
5.3 REMOTE CONTROL VIA RS-232................................................................................ 32 
5.4 REMOTE CONTROL VIA RS-422/485......................................................................... 34 
5.5 REMOTE CONTROL VIA LAN.................................................................................... 35 
A REGULATORY COMPLIANCE.............................................................................. 37 
B SAFETY PRECAUTIONS......................................................................................... 42 
B.1 SAFETY PRECAUTIONS............................................................................................. 43 
B.1.1 General Safety Precautions............................................................................. 43 
B.1.2 Anti-static Precautions.................................................................................... 44 
B.1.3 Product Disposal............................................................................................. 45 
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 45 
B.2.1 Maintenance and Cleaning.............................................................................. 45 
B.2.2 Cleaning Tools................................................................................................. 46 
C HAZARDOUS MATERIALS DISCLOSURE......................................................... 47 
C.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS 
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ....................................... 48 

S19M/S24M Marine Monitor

Page vii

List of Figures

Figure 1-1: S19M/S24M Marine Monitor........................................................................................2

Figure 1-2: Front Panel ..................................................................................................................3

Figure 1-3: Display Control Buttons.............................................................................................4

Figure 1-4: Bottom Panel...............................................................................................................5

Figure 1-5: S19M Rear Panel.........................................................................................................5

Figure 1-6: S24M Rear Panel.........................................................................................................6

Figure 1-7: S19M Dimensions (mm)..............................................................................................9

Figure 1-8: S24M Dimensions (mm)............................................................................................10

Figure 3-1: S19M Cutout Dimensions.........................................................................................17

Figure 3-2: S24M Cutout Dimensions.........................................................................................17

Figure 3-3: S24M Panel Mounting Hole Covers.........................................................................18

Figure 3-4: Tighten the Panel Mounting Clamp Screws...........................................................19

Figure 3-5: I/O Interfaces .............................................................................................................20

Figure 3-6: 18V ~ 36V DC Power Input Terminal Block Pinouts..............................................21

Figure 3-7: USB Type A Connector Pinouts..............................................................................23

Figure 4-1: OSD Button Locations..............................................................................................27

Figure 4-2: Main Menu..................................................................................................................28

Figure 5-1: IEI Monitor Remote Application Screen..................................................................32

Figure 5-2: IEI Monitor Remote AP – RS-232 .............................................................................33

Figure 5-3: IEI Monitor Remote AP – RS-422/485......................................................................35

Figure 5-4: IEI Monitor Remote AP – LAN..................................................................................36

S19M/S24M Marine Monitor

Page viii

List of Tables

Table 1-1: Model Variations...........................................................................................................2

Table 1-2: System Specifications..................................................................................................8

Table 3-1: Panel Mounting Clamps.............................................................................................18

Table 3-2: Buzzer Terminal Block Pinouts.................................................................................20

Table 3-3: DVI Input Connector Pinouts.....................................................................................21

Table 3-4: RJ-45 Connector Pinouts...........................................................................................22

Table 3-5: RS-232 Connector Pinouts ........................................................................................22

Table 3-6: RS-422/485 Terminal Block Pinouts .........................................................................23

Table 3-7: VGA Output Connector Pinouts................................................................................24

Table 3-8: VGA Output Connector Pinouts................................................................................24

Table 4-1: OSD Control Buttons..................................................................................................27

Table 4-2: OSD Menu Structure and Options ............................................................................30

S19M/S24M Marine Monitor

Page 1

1 Introduction

Chapter

1

S19M/S24M Marine Monitor

Page 2

1.1 Overview

Figure 1-1: S19M/S24M Marine Monitor

The S19M/S24M marine-grade monitor, equipped with IP 66 compliant front panel and IP

22 compliant rear cover, is the latest member of IEI’s line of sophisticated LCD designs.

With two VGA, two DVI and one BNC inputs, the S19M/S24M provides multiple ways to

connect with computers. In addition, one VGA and one BNC outputs allow simultaneous

display on other monitors.

1.2 Model Variations

The model numbers and model variations are listed below.

Model LCD Size Max. Resolution Contrast Ratio

S19M-AD/PC-R10

19” 1280 x 1024 (5:4) 2000:1

S24M-AD/PC-R10

24” 1920 x 1080 (16:9) 5000:1

Table 1-1: Model Variations

S19M/S24M Marine Monitor

Page 3

1.3 Features

Some of the S19M/S24M features are listed below:

 IP 66 compliant front panel and IP 22 compliant rear cover

 Flat-bezel projected capacitive touchscreen

 -15ºC ~ 55ºC wide range operating temperature

 Excellent visual performance

o Full OSD function configuration

o 0 to 100% full range dimming

o 178°/178° wide viewing angles

 Multiple video inputs, including two VGA, two DVI and one BNC

 Multiple video outputs, including one VGA and one BNC

 Isolated AC and DC inputs with redundant power protection

1.4 Front Panel

The front side of the S19M/S24M (Figure 1-2) is a flat panel LCD screen surrounded by

an aluminum frame. The bottom frame includes four OSD buttons and an ambient light

sensor.

Figure 1-2: Front Panel

S19M/S24M Marine Monitor

Page 4

1.4.1 Display Control Buttons

The display control buttons are located on the bottom right corner of the front panel. The

function of each button is described in the following diagram. These buttons can also be

used to control OSD (on-screen display). Please refer to Chapter 4 for more detail.

Figure 1-3: Display Control Buttons

1.5 Bottom Panel

The bottom panel of the S19M/S24M has the following I/O interfaces (Figure 1-4):

 1 x 100 V ~ 240 V AC power input jack

 1 x 18 V ~ 36 V DC power input terminal block

 1 x Buzzer terminal block

 1 x BNC composite video input connector

 1 x BNC composite video output connector

 2 x DVI input connectors

 1 x RJ-45 connector for remote control

 1 x RS-232 DB-9 connector for remote control

 1 x RS-422/485 terminal block for remote control

 1 x USB Type A connector for touchscreen

 2 x VGA input connectors

 1 x VGA output connector

S19M/S24M Marine Monitor

Page 5

Figure 1-4: Bottom Panel

1.6 Rear Panel

The rear panel provides access to retention screw holes that support VESA mounting.

See

Figure 1-5 and Figure 1-6.

Figure 1-5: S19M Rear Panel

S19M/S24M Marine Monitor

Page 6

Figure 1-6: S24M Rear Panel

1.7 System Specifications

The technical specifications for the S19M/S24M are listed in Table 1-2.

Specifications S19M S24M

LCD Size

19" 24”

Panel Type

PMVA AMVA

Max. Resolution

1280 x 1024 (5:4) 1920 x 1080 (16:9)

Contrast Ratio

2000:1 5000:1

Brightness (cd/m

2

)

300 300

LCD Color

16.7M 16.7M

Pixel Pitch (um)

294 x 294 276.75 x 276.75

Viewing Angle (H-V)

178° / 178° 178° / 178°

S19M/S24M Marine Monitor

Page 7

Specifications S19M S24M

Backlight MTBF (HRs)

50,000 50,000

Touch Controller

EXC3188 (10-point)

Touchscreen

Projected capacitive type

Scalar Chip

STDP8028

I/O Interfaces

DVI-D signal input: 2 x DVI (24-pin, female)

VGA signal input: 2 x D-sub (15-pin, female)

VGA signal output: 1 x D-sub (15-pin, female, clone of

VGA input)

Composite video input: 1 x BNC (female)

Composite video output: 1 x BNC (female)

Remote control: 1 x RS-232 DB-9 (non-isolated)

1 x RS-422/485 terminal block (5-pin,

non-isolated)

1 x RJ-45

Touchscreen: 1 x USB Type A (female)

Isolated AC power inlet: 100 V ~ 240 V AC

Isolated DC power input terminal block: 18 V ~ 36 V DC

Buzzer: 1 x Buzzer (5-pin, terminal block)

PIP

Yes

OSD Buttons

Four capacitive sensor buttons (menu, brightness down,

brightness up, LCD on/off)

Sensor

Ambient light sensor (0% ~ 100%)

Power Requirement

Dual power supply

AC power: 100V ~ 240V, 2-1A, 50-60Hz

DC power: 18V ~ 36V, 8-4A

Operating Temperature

-15ºC ~ 55ºC

Storage Temperature

-20ºC ~ 60ºC

S19M/S24M Marine Monitor

Page 8

Specifications S19M S24M

Operating Humidity

5% ~ 95% RH

Thermal Design

Fanless

Housing

Aluminum front, sheet metal rear (Black C)

Cut-out Dimensions

(L x W)

442 mm x 373 mm 576 mm x 356 mm

Dimensions (L x W x D)

463 mm x 394 mm x 76 mm 592 mm x 374 mm x 74 mm

Mounting

VESA 100 mm x 100 mm

VESA 100 mm x 100 mm or

100 mm x 200 mm

Weight (Net/Gross)

7.74 kg/11.54 kg 11.48 kg/15.97 kg

IP Rating

IP 66 compliant front panel

IP 22 compliant rear cover

EMC

CE, FCC

Safety

DNV, IEC 60945 4th, IACS-E10 compliant

Table 1-2: System Specifications

S19M/S24M Marine Monitor

Page 9

1.8 Dimensions

The 19M dimensions are shown below.

Figure 1-7: S19M Dimensions (mm)

S19M/S24M Marine Monitor

Page 10

The S24M dimensions are shown below.

Figure 1-8: S24M Dimensions (mm)

S19M/S24M Marine Monitor

Page 11

2 Unpacking

Chapter

2

S19M/S24M Marine Monitor

Page 12

2.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during installation may result in

permanent damage to the S19M/S24M and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the S19M/S24M. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the S19M/S24M or any other electrical component is handled, the

following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the S19M/S24M, place it on an

anti-static pad. This reduces the possibility of ESD damaging the

S19M/S24M.

2.2 Unpacking Precautions

When the S19M/S24M is unpacked, please do the following:

 Follow the anti-static precautions outlined in Section

2.1.

 Make sure the packing box is facing upwards so the S19M/S24M does not fall

out of the box.

 Make sure all the components shown in Section

2.3 are present.

La pagina sta caricando ...

IEI Technology S24M Manuale utente

Questo manuale è adatto anche per

IEI Technology S24M Manuale utente

in altre lingue

Altri documenti