Timex Expedition Adventure Tech Altimeter Guida utente

®

W-195 567-095006 NA

1

SELECTING PRESSURE AND TEMPERATURE UNITS 24

CALIBRATING THE BAROMETER 25

ALTI - ALTIMETER MODE 28

USING THE ALTIMETER 29

SELECTING ALTITUDE UNITS 30

ALTIMETER PERFORMANCE 31

CALIBRATING THE ALTIMETER AND CLEARING HIGH AND ACC 32

CHRO - CHRONOGRAPH MODE 34

TERMINOLOGY 34

USING THE CHRONOGRAPH 35

LAP/SPLIT TIMING 36

CHANGING THE DISPLAY FORMAT 37

If no laps have yet been taken: 37

If you have taken at least one lap: 38

REVIEWING STORED LAP/SPLIT TIMES 38

TIMER - COUNTDOWN TIMER MODE 40

SETTING THE COUNTDOWN TIMER 40

USING THE COUNTDOWN TIMER 41

ALARM - ALARM MODE 43

SETTING AN ALARM 43

SELECTING AND ARMING/DISARMING ALARMS 44

BACKUP ALERT 45

TRADEMARK AND WARRANTY INFORMATION 46

INTRODUCTION 4

WATCH FEATURES 5

WA

TCH MODES 8

BUTTON FUNCTIONS 9

NORMAL OPERATION 9

SETTING OPERATION 11

WATCH DISPLAY SYMBOLS 13

WEATHER FORECASTING 14

NOTES ON CALIBRATING THE ALTIMETER AND BAROMETER 15

WHAT IS CALIBRATION? 15

HOW OFTEN SHOULD I CALIBRATE? 15

DO I NEED TO CALIBRATE BOTH THE BAROMETER AND THE ALTIMETER? 16

TEMPERATURE ACCURACY 17

TIME - TIME OF DAY MODE 18

SETTING TIME OF DAY 19

USING THE DUAL TIME ZONE FEATURE 21

Viewing the secondary time zone 21

Switching time zones 22

VIEWING TEMPERATURE AND AIR PRESSURE DATA 22

BARO - BAROMETER MODE 23

VIEWING TEMPERATURE AND PRESSURE DATA 24

32

Watch Features

Time of Day

• Displays hours, minutes and seconds in 12- or 24-hour

format for two time zones.

• Displays month and date, as well as day of the week.

• Optional hourly chime.

Altimeter

• Reports altitude from -2296 to 29,520 feet (-700 to

9000 meters) with 10 ft or 5 m resolution.

• Displays current altitude as well as a graph of altitude

change over time.

• Displays accumulated total of all altitude gains, known

as “total ascent” or “climb”.

• Records highest altitude achieved.

• Selectable display units (meters or feet)

Introduction

Welcome!

Thank you for purchasing a TIMEX® EXPEDITION®

adventure tech altimeter watch. The watch is equipped

with a variety of features to enhance your outdoor

experience. So, if you are trekking the trails, skiing the

slopes or just hanging out, enjoy the journey.

Register your product at www.timex.com

54

Chronograph

• Time events up to 24 hours with 1/100-second

resolution.

• Store up to 30 lap/split times.

• View stored lap times as well as best (shortest) lap

time, average lap time and total event time.

Count Down Timer

• Time events up to 24 hours. An alert is generated

when the timer reaches zero.

• Timer can be set to count down to zero once or to

repeat the countdown indefinitely.

Alarm

• Five independent daily alarms, each with a five-minute

backup alert.

Barometer

• Reports air pressure from 8.85 to 32.45 inches of

Mercury (“inHg”) (300 to 1100 mbar) with 0.05 inHg

(1 mbar) resolution.

• Displays current air pressure as well as a graph of

change in air pressure over time.

• Both sea level and local (absolute) air pressure can be

displayed.

• Forecasts the weather for the next 4–6 hour period.

• Selectable display units (inHG or mbar)

Thermometer

• Selectable display units (°F or °C)

• Reports current air temperature from 14 to 140 °F

(-10 to 60 °C).

76

TIMER - The Countdown Timer is useful for timing

fixed-time events

ALARM -Five daily alarms to keep you on time

TIP: Press and hold the MODE button for three seconds to

go directly to TIME mode from any other mode in the

watch.

Button Functions

The buttons on your watch are multi-functional, serving

two main purposes - enabling you to perform everyday

functions like checking the time and timing a workout,

and setting things like Time of Day or an Alarm.

Normal Operation

The buttons on your watch largely operate in the same

way from mode to mode and the primary functions for

them are printed on the case itself. This section describes

the typical functions of the buttons.

INDIGLO® Night-Light

Watch Modes

The features of this watch are grouped into modes that

are accessible by pressing and releasing the MODE button

– each depression of the MODE button takes you to the

next mode in the loop. The modes are arranged in the

following order:

TIME > BARO > ALTI > CHRO > TIMER > ALARM

TIME - Displays the time of day and date as well as

weather info

BARO - View air pressure, temperature & weather

information

ALTI - Presents altitude and temperature data

CHRO - Use the Chronograph for timing purposes

98

Setting Operation

When setting Time of Day, Alarms or the Countdown Timer

and so on, the button functions change from what is print-

ed on the case.

NOTE: These setting functions are the same in any mode

where you can set a value.

1. Press and hold the SET button. While you are holding

the button, “HOLD ADJUST” will appear on the display.

2. After a couple of seconds, the “HOLD” message will

disappear followed by a flashing value.

3. Change the flashing value by pressing either

START/SPLIT (to increase) or STOP/RESET

(to decrease). Press and hold the button to

increase/decrease the value quickly.

4. When the flashing value is set as intended, press

MODE to advance to the next value.

1110

SET

START / SPLIT

INDIGLO®

STOP / RESET

MODE

Watch Display Symbols

Alarm is armed (flashing if backup alarm is active)

Chronograph is running

Hourly Chime is enabled

Countdown Timer is running

Indicates weather forecast

5. Repeat steps 3 and 4 for each of the values you wish

to set.

TIP: If you accidentally skip past a setting, continue to

press and release the MODE button to move all the way

through the settings and back to the one that requires

adjustment.

6. When you are satisfied that everything is set as

intended, press the SET button to save your settings

and exit.

1312

PRESS TO EXIT SETTING

PRESS FOR NEXT VALUE

INCREASE FLASHING VALUE

LAMP

DECREASE FLASHING VALUE

Notes on calibrating the Altimeter and Barometer

The watch relies on a sensitive electronic sensor to

measure the air pressure and temperature. This sensor

must be calibrated periodically to maintain the high degree

of accuracy you expect from the watch.

What is calibration?

“Calibration” is simply a technique to improve the accura-

cy of the pressure/temperature sensor, primarily by com-

pensating for local temperature and weather effects. The

watch employs two related methods of calibration, using

either sea level pressure or the local altitude as a refer-

ence, depending on the watch mode used for calibration.

How often should I calibrate?

Timex recommends that you calibrate the sensor prior to

any activity where you will be using the altimeter feature

Weather Forecasting

The watch can predict the weather for the upcoming 4 - 6

hour period based on the air pressure trend information for

the previous twelve hours. The weather forecast is indicated

at the top of the watch display by a series of symbols.

Generally, if the air pressure is rising, the weather situation is

considered to be improving and is indicated by the presence

of the sun symbol. If the air pressure trend is falling, then the

weather situation is worsening and is indicated by showing

the clouds and/or precipitation symbols.

The weather forecast is always visible in TIME and BARO

modes and visible in ALTI mode when no altitude changes

are detected.

1514

CONDITIONS

reference source available.

For example, if you are standing at a trail head and know

the correct altitude, then the most accurate calibration will

be obtained by calibrating within ALTI mode (since it relies

on altitude as the reference). However, if you don’t know

your altitude, you can find out the current sea level pres-

sure (published online or in a newspaper) and calibrate the

sensor within BARO mode. For example, the U.S. weather

service publishes the sea-level pressure for all of its

stations at http://www.weather.gov

Temperature Accuracy

When worn on your wrist, the thermometer reading is

affected by body heat and may report a temperature

different from the actual air temperature by 10 degrees or

more. Long periods of exposure to direct sunlight may also

affect the accuracy. Try wearing the watch outside your

and then again whenever you experience significant

changes in altitude or temperature during your activity.

If you are not using the altimeter feature, then daily

calibration will maintain the accuracy of the barometer

and weather forecasting feature.

Whenever possible, the sensor should be calibrated soon

after you experience significant temperature changes.

Do I need to calibrate both the Barometer and the

Altimeter?

No. BARO mode calibrates the sensor based upon the sea

level air pressure, while ALTI allows you to calibrate the

sensor by telling the watch about your current altitude.

Calibration performed in either mode will calibrate the

sensor for all modes. For the best accuracy, we recom-

mend that you choose only one calibration method each

time you calibrate the sensor, based on the most accurate

1716

(in the lower display line) and the weather forecast

(at the top of the display).

Setting Time of Day

Refer to section entitled “Setting Operation” on page 11 to

understand how the buttons function during setting.

You may set the following values for Time of Day:

Hour, Minute, Seconds, Year, Month, Date, Date Format,

Time Format, Hourly Chime.

jacket (in cold weather) or clipping it to your belt or pack

(ideally in an area not constantly exposed to the sun) to

improve the accuracy of the temperature readings during

outdoor activities. For the most accurate readings, remove

the watch from your wrist and put in shade for at least

several minutes.

The watch can measure water temperature also, if

submerged. Be sure to select temperature display before

placing the watch in water, as buttons should not be

pressed with the watch underwater.

TIME - Time of Day Mode

In this mode you may view the current time and date in

either of two time zones and switch between them. The

time can be displayed in 12- or 24-hour format. In addition

to the time of day, the watch can display the current

barometer (air pressure) value or the current temperature

1918

Using the Dual Time Zone feature

The watch can keep track of the time for two zones

(T1 and T2). By default, T1 is the “primary” time zone (the

one that you can see) and T2 is the “secondary” time zone

(the one you can’t see). The indicator for the primary time

zone is shown in the lower left of the display.

Viewing the secondary time zone

You may temporarily view (or “peek” at) the secondary

time zone by briefly pressing and holding the STOP/RESET

button. While you are “peeking” at the secondary time

zone, its indicator (T1 or T2) will flash in the lower

left-hand side of the display. When you release the

STOP/RESET button, the watch will display the time for

the primary time zone once again.

NOTES:

• Be sure you have selected the intended time zone

(T1 or T2) before you begin setting; you cannot switch

zones while setting (see “Using the Dual Time Zone

feature” on pg 21).

• When setting the hour value, be sure to set to the

correct part of the day (AM or PM) (12-hour format only).

• The seconds’ value can only be set to “0” and cannot

be set individually for each time zone.

• The day of the week is automatically calculated based

on the date.

• The watch will automatically adjust for leap years up

to 2049.

• When the hourly chime is enabled, a confirmation

beep will also be generated whenever a key is

pressed.

2120

BARO - Barometer Mode

Want a better understanding of the forces that influence

the weather? This is the mode to do just that – here you

can view the current air pressure (local and sea level),

monitor the current temperature and study the changes in

air pressure over time, presented in a graphical format.

Finally, the weather forecast for the next 4 - 6 hours is

shown at the top of the display.

Switching time zones

If you wish to switch to the secondary time zone, simply

continue holding the STOP/RESET button until the time

zone indicator (T1 or T2) stops flashing (this takes about

three seconds). This will be your new primary time zone

until you switch it back.

Viewing Temperature and Air Pressure Data

While in TIME mode, press and release the START/SPLIT

button to view the following information on the lower line

of the watch display:

• The current air pressure

• The current temperature

• The month and date

2322

When viewing the Time of Day, Sea Level Pressure and

Temperature group, press STOP/RESET to toggle tempera-

ture display units (°F or °C).

NOTE: Unit selection made for temperature and barometric

pressure in BARO mode applies to all modes in the watch.

For example, if you select “°C” for the temperature display

in BARO mode, it will also appear in °C in Time of Day and

Altimeter modes.

Calibrating the Barometer

Calibration in BARO mode allows you to synchronize the

weather forecasting feature with the current weather

situation and also to calibrate the pressure sensor for

improved accuracy.

Refer to section entitled “Setting Operation” on page 11 to

understand how the buttons function during setting. Refer

Viewing Temperature and Pressure Data

Press and release MODE until you see “BARO” on the

display.

Press and release the START/SPLIT button to view each of

the following data combinations:

• Temperature, Sea Level Pressure and Local Pressure

• Time of Day, Sea Level Pressure and Temperature

• Time of Day, a graph of the sea level pressure for the

last 24 hours and Sea Level Pressure.

Temperature is updated every four minutes and baromet-

ric pressure every 2.5 minutes.

Selecting Pressure and Temperature Units

When viewing the Temperature, Sea Level Pressure and

Local Pressure group, press STOP/RESET to toggle baro-

metric pressure display units (inches of mercury [inHg] or

millibars [mbar]).

2524

What is “Sea Level Pressure”?

Sea Level Pressure is simply the air pressure for a specific

location adjusted to account for the air pressure difference

due to the altitude of the location. Because very few

places on the earth are actually at sea level, this adjust-

ment factor was devised to allow for easy comparison of

air pressure values from place to place. For example, with-

out this compensation, a pressure reading of 29.5 inHg in

Denver, CO would not mean the same as the same reading

in Miami, FL due to the large difference in altitude.

Meteorologists would have a very difficult time measuring

the change in the weather as fronts move across the land

masses if there was no way to compensate for the altitude

effects. So, whenever you see a barometer value published

online or in a newspaper, it is always the pressure adjust-

ed for the altitude of the measuring station.

to the section entitled “Notes on calibrating the Altimeter

and Barometer” on page 15 for general information regard-

ing calibration.

1. Press and hold SET until the word “SET” appears in the

lower line of the display.

2. Using START/SPLIT or STOP/RESET, adjust the

weather icons to the actual weather conditions.

3. Press MODE to move on to entering the sea level air

pressure.

4. Using START/SPLIT (to increase) and STOP/RESET

(to decrease), adjust flashing value.

5. Repeat steps 3 and 4 until for each flashing value until

the pressure is set as intended.

6. Press SET to complete calibration.

2726

Using the Altimeter

Press and release MODE until you see “ALTI” on the dis-

play. After a couple of seconds, the watch will display the

following data, in the order shown, for two seconds each:

• The highest recorded altitude (indicated by “HIGH” in

the lower display line).

• The total accumulated positive altitude changes

(indicated by “ACC” in the lower display line).

Typically, if you are above sea level, the “local” pressure

value that the watch also displays will be lower than the

sea level pressure (because air pressure decreases with

altitude) and if you are at a point below sea level the local

pressure will be slightly higher.

Incidentally, this difference between sea level air pressure

and the local air pressure is how the watch determines

the altitude.

ALTI - Altimeter Mode

This mode provides altitude and temperature information

to make outdoor activities like hiking, mountain biking and

trail running more enjoyable. The watch will keep track of

the highest altitude you achieved as well as accumulate all

of the positive altitude changes you experience. These

statistics are visible when you first enter ALTI mode.

2928

Altimeter Performance

When ALTI mode is first entered, the watch will update the

altitude information every two seconds and will continue

this fast data update rate for thirty minutes. After thirty

minutes elapses, if the watch determines that the altitude

is no longer changing significantly, it will reduce its data

update rate to that of the barometer function (every 2.5

minutes). At that point, two things will happen:

1. The weather icons will appear in the upper part of the

display indicating the forecast.

2. The watch will stop data accumulation for the ACC

and HIGH statistics.

The watch will continue to monitor the air pressure at this

slower rate and, if it determines that the altitude is chang-

ing significantly, it will go back to faster update rate. If this

change occurs, the weather icons will be removed from

After the accumulated data is displayed, the watch

will then display either of the following views of the

altitude data:

• Current time, altitude and temperature data.

• A graph of the altitude changes for the last five hours

(each column represents 10 minutes) shown in the

center of the display. The current time is displayed in

the upper line and the current altitude is displayed in

the lower line.

Press and release the START/SPLIT button to switch

between these two views.

Selecting Altitude Units

While viewing the current time, altitude and temperature

data, press STOP/RESET to switch units between feet (FT)

and meters (M).

3130

1. Press and hold SET until the word “CAL” appears in

the upper line of the display and the sign of the

calibration value is flashing.

2. Press START/SPLIT to adjust the sign (positive for

altitudes above sea level, negative for altitudes below).

3. Press MODE to move on to adjusting the current

altitude value.

4. Using START/SPLIT (to increase) and STOP/RESET

(to decrease), adjust flashing value.

5. Repeat steps 3 and 4 for each value of the calibration

altitude.

6. Press MODE to move on to enable clearing of the

HIGH data value. “HIGH” will be flashing in the upper

line; the current value for the highest altitude will be

displayed.

7. Press and hold START/SPLIT to clear the value, if

desired.

the display and the watch will again update the statistical

data with altitude information as necessary.

Calibrating the Altimeter and Clearing

HIGH and ACC

Calibration in ALTI mode allows you to calibrate the

pressure sensor for improved accuracy as well as clear

the HIGH and ACC data values.

Calibration operates exactly like setting, so refer to the

section entitled “Setting Operation” on page 11 to under-

stand how the buttons function during setting. Also refer

to the section entitled “Notes on calibrating the Altimeter

and Barometer” on page 15 for general information regard-

ing calibration.

For proper calibration, adjust the “CAL” value to reflect

your actual altitude. The “CAL “ value can be set to a value

from -2296 ft (-700m) to +26520 ft (+9000m).

3332

track, the lap time would be the time for one lap around

the track, assuming that you push the START/SPLIT button

as you cross the start/finish line each time.

Split Time: The elapsed time from the start of the

workout, sometimes called the “total time”.

“Taking a Lap”: Marking the end of one segment (or lap)

and the beginning of another by pressing START/SPLIT

while the Chronograph is running. Also called “taking a

split”.

Using the Chronograph

Press and release MODE until you see “CHRO” on the

display.

Start the Chronograph by pressing START/SPLIT and stop

it by pressing STOP/RESET.

While the Chronograph is stopped, you may restart it by

pressing START/SPLIT, or you may reset it to zero by

8. Repeat steps 6 and 7 to clear the ACC data.

9. Press SET to complete calibration.

CHRO – Chronograph Mode

The Chronograph gives you the ability to time a hike, a ski

or a run – just about anything you’d like to time. You can

also track the time for specific segments of an activity

with the lap/split features; the Chronograph will store

lap/split times for thirty laps as well as the best (or short-

est) lap time and the average for all the stored lap times.

In the event you take more than thirty laps, the watch will

store timing information for the first thirty.

Terminology

Lap Time: The elapsed time for a segment of a course,

marked by pressing the START/SPLIT button on the watch.

For example, if you are running on a standard quarter-mile

3534

Changing the Display Format

You have the option of viewing either the lap or split time

in the large digits in the center of the watch display. The

display format can be changed at any time, though the

method changes based on whether or not laps have been

taken. The word “LAP” will appear on the display to inform

you where the lap time is displayed.

If no laps have yet been taken:

Press SET. “FORMAT” will appear on the display, followed

by the current configuration, which will be flashing. Press

START/SPLIT or STOP/RESET to select the desired format

and then press SET to save the setting and return to the

Chronograph display.

pressing and holding STOP/RESET.

You may leave CHRO mode while the Chronograph is run-

ning; it will continue to run in the background, indicated by

the icon on the display when in TIME mode.

Lap/Split Timing

Press START/SPLIT each time you pass a segment marker

(like trail head marker) to complete the timing of the

previous lap or segment and begin timing a new one. The

lap and split times for the segment just completed will be

displayed for ten seconds (it will still be timing the new

segment in the background, indicated by the flashing

symbol on the display). If you wish to return to the running

Chronograph immediately, press MODE to dismiss the

previous lap time data.

3736

La pagina sta caricando ...

Timex Expedition Adventure Tech Altimeter Guida utente

Timex Expedition Adventure Tech Altimeter Guida utente

in altre lingue

Documenti correlati

Altri documenti