iON SnapCam Lite Guida Rapida





Quick Start Guide



EN-2

1. Introduction

iON SnapCam Lite is a mini wearable camera. It allows users to

take photos and video record life’s moments by simply pressing

one button.

2. Key Features

y Ultra slim and light-weight

y Take high quality photo and HD video

y Detachable clip to mount on clothes

y G-sensor to detect the orientation and rotate the view



EN-3

3. Functional Parts



EN-4

1 MicroSD Card

Slot

¾ MicroSD card storage location.

2 Status LED ¾ Show the camera status.

3 Wide Angle Lens ¾ Capture the live view.

4 Reset Button ¾ Reset the camera.

5 Silicon Cover ¾ Shield the camera from water

and dust.

6 Capture Button ¾ Take a single photograph.

¾ Start/Stop video recording.

7 Micro USB Port ¾ Connect to an external power

supply for charging.

¾ Connect to a computer for data

transfer.

8 Time Lapse

Switch

¾ Switch to turn the Time Lapse

function on or off.

4. First Time Use

4.1. Charging your SnapCam Lite



EN-5

Charge the built-in battery before starting to use your camera.

The camera will take approximately 2 hours to fully charge from

flat.

The LED will turn solid RED once the camera is fully charged.

Note:

y Ensure your camera is charged before each use.

y For charging your camera more efficiently, make sure the

Time Lapse switch is at the OFF position.

4.2. Inserting a MicroSD Memory Card



EN-6

You must insert a MicroSD card (not supplied) before using the

camera. The camera supports MicroSD card from 2GB to 32GB

(Class 6 or higher is recommended).

Notes:

y There is only one direction to insert the MicroSD memory

card into the slot. Do not force the MicroSD card into the

slot as this may damage both the camera and the

MicroSD memory card.

y The MicroSD memory card must be formatted before use.

4.3. Setting Date & Time

When the camera is used for the first time, or it has been restored

to default settings, you need to set the camera’s clock to ensure

that your video and photo files are saved with the correct date/



EN-7

time information.

To set up the camera clock:

1. Insert a MicroSD card to the camera.

2. Connect the camera to a PC to enter into USB mode

(Refer to section 5.5).

3. Open the MicroSD file folder, create a file in any format

(e.g. txt file) and name it with the format “set-YYYYMMDD-

HHMM”

YYYY, MM, DD, HH, MM represent the year, month and

day, hour, minute of existing time.

4. Disconnect the camera from your PC, press the Capture

button, the camera will scan the file and write it to the

system clock.



EN-8

5. Using the Camera

5.1. Wearing your SnapCam Lite

5.1.1. Mounting with Clip Holder

Note:

This method is suitable for wearing your camera on a

jacket or relatively thick clothes. Wear your camera

vertically, otherwise, the camera may slip and produce a

tilted view.



EN-9

1. Install the clip holder on your camera.

2. Clip your camera in a vertical position where you wish.

5.1.2 Mounting with Magnet Clip



EN-10

Note:

Magnet Clip not included – sold separately. This method is

suitable for wearing your camera on relatively thin clothes.

Wear your camera vertically, otherwise, the camera may

slip and produce a tilted view.



EN-11

1. Detach the magnet sheet from the magnet clip socket.

2. Install the magnet clip to your camera.

3. Attach the magnet clip with camera to an area outside your

clothing while putting the magnet sheet inside the

corresponding area of your clothing. The magnetic field will

help the two pieces lock into place.

5.2. Taking a Single Photo

Press the Capture button very briefly to take a photo. A short

beep and a flash of Blue LED indicates the action was successful.

Be aware to not block the camera lens with your finger, or it will



EN-12

shield the camera view.

Note:

When your camera battery is low, the status LED will flash

in red. You need to recharge your camera. (Refer to

section 4.1)

5.3. Taking Time Lapse photos

Time Lapse mode captures a series of photos at 30 second

intervals.

To Start Time Lapse:

Slide the Time Lapse switch to ON position to enter the Time

Lapse mode, the camera will initiate a countdown. The Blue LED

will flash each time a photo is taken.

Note

:

When your camera battery is low, the status LED will flash

in red. You need to recharge your camera. (Refer to

section 4.1)

To Stop Time Lapse:

Slide the Time Lapse switch to OFF position to exit the Time

Lapse mode.

Notes:

y You can also take single photos and record videos during

Time Lapse mode. After the single photo is captured or

the video is recorded, the camera will resume to Time



EN-13

Lapse mode.

y Turn off the Time Lapse mode when you want to exit the

mode, or the camera will continue taking photos until the

battery depletes or the Time Lapse button is switched to

OFF.

5.4. Recording Videos

Press and hold the Capture button to start recording, the camera

will beep twice indicating recording has started. The LED indicator

illuminates Blue throughout recording.

To stop Recording, press and hold the Capture button again, the

camera will beep for 1 second and the LED will turn off.

Notes:

y The Still Photo function is disabled during video recording.

y When the memory card is full, the camera will beep 3 times

twice and the LED will flash Blue and Red alternately for 5

seconds.

y When your camera battery is low, the status LED will flash

in red. You need to recharge your camera. (Refer to section

4.1)

Notes:

During operation, please do not release MicroSD card from the

card slot as this may damage saved files or cause camera

malfunction.



EN-14

5.5. Connecting your Camera to a

Computer

The camera can be connected to a computer as a mass storage

device and transfer your photo/video files fo r storage.

1. Connect your camera to a computer via the USB cable

included.

2. Press the Capture button to enter into mass storage mode.

When the camera is connected to the computer as a mass

storage device, you can:

1. Open the folder and browse the files saved on the memory

card.

2. Format the MicroSD card.

3. Set the camera clock. (Refer to section 4.3)



EN-15

6. Specifications



Lens Wide angle lens

Water Resistance Splash proof (IPX4)

Still Image resolution 5MP

Video Resolution 720P @ 30fps

Video Format MPEG4 (H.264) .AVI File

Photo Format JPG

Memory Slot MicroSD card

Support System Windows XP, Vista, 7 and 8;

Mac OS X 10.6 and later

Microphone Built-in

Battery Life Approximately 120 minutes

continuous recording

Dimension (L x H x W) 42 x 42 x 13.4 mm

Weight 25.6g

Operation Temperature

-10℃ ~ 40℃

Storage Temperature

-30℃ ~ 80℃



EN-16

7. Troubleshooting

Problem Cause Solution

Unable to

record videos

or photos

1. MicroSD

card is not

inserted

2. Memory full

3. Camera

malfunction

1. Insert a MicroSD card

2. Replace with a memory card with

space available for contents

3. Reset the camera

Cannot find

removable

disk after

connecting the

camera to the

computer

Connection

failure

1. Make sure all cable connections

are secured

2. Restart the computer if necessary

Blurry images

The lens of

camera is dirty

Clean the lens with soft and dry

cloth



EN-17

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for

help.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2)This device must accept any interference received, including

interference that may cause undesired operation.

Shielded cables must be used with this unit to ensure compliance with the

Class B FCC limits



EN-18



TRADEMARK INFORMATION

® The iON logo is a registered trademark of World Wide Licenses Limited

Questions?

Need Some Help?

This manual

should help you

understand your

new product.

If you still have

questions,

visit our website:

www.ioncamera.com

Like Us:

www.facebook.com/ioncamera

Tweet Us:

www.twitter.com/ioncamera



EN-19

Learn more.

Learn more about iON camera features at http://www.ioncamera.com

For instructions and safety information, see the iON User Guide. Download

the PDF at http://www.ioncamera.com/ion/User-Guides.html

.

Get support. (i.e. Warranty)

Visit http://www.ioncamera.com/ion/Support.html

for all iON camera

support. If you are located in the United States of America, please contact

Customer Service at 855-411-4466. If you are located in Canada, please

contact Customer Service at 905-513-7733.





Schnellstartanleitung

La pagina sta caricando ...

iON SnapCam Lite Guida Rapida

iON SnapCam Lite Guida Rapida

in altre lingue

Documenti correlati

Altri documenti