Viscount Unico 700 Manuale utente

Marca: Viscount

Modello: Unico 700

Categoria: Apparecchiature musicali supplementari

Tipo: Manuale utente

viscount

User Guide - EN

Gebruikersgids - NL

Guida Utente - IT

Ver. EU - 1.4

UNICO 700

WARNING: READ THIS FIRST!

WARNING

AVIS

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ÉLECTRIQUE

NE PAS OUVRIR

This symbol is intended to alert the user to the

presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK:

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE

AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,

SHOULD NOT BE PLACED ON THIS APPARATUS.

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

"INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS"

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves

or other apparatus (including amplifiers) that produces heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third

prong are provided for your safety. If the provided plug does not fit in to your outlet, consult an electrician for

replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold, with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

NOTE: The socket-outlet shall be installed near the equipment and shall be easily accessible.

Viscount UNICO 700User Guide

INDEX

1. Important notes .............................................................................................................................. 2

1.1 Looking after the product .............................................................................................................................. 2

1.2 Notes about the manual .................................................................................................................................. 2

2. Introduction.................................................................................................................................... 4

3. General description ........................................................................................................................ 5

4. Switching on and main video page ............................................................................................... 10

5. Setting the volumes (Volumes function) .......................................................................................11

6. Tuning the instrument (Tuning menu) ........................................................................................ 12

7. The organ styles (Styles menu) ..................................................................................................... 13

8. Selecting and regulating the voices (Voices menu) ...................................................................... 14

8.1 Regulating the volume (Volume Level function)....................................................................................... 14

8.2 Regulating the audio parameters (Edit Parameters function) ..................................................................15

8.3 Selecting the alternative voices (Alternative Voice function)................................................................... 16

9. Instrument general settings (Set-Up menu) ................................................................................. 18

9.1 Setting the routing of the voices on the rear audio outputs (Ext. Out Router function) ................... 18

9.2 Configuring the audio outputs on the rear (Ext. Out Config function) ................................................ 21

10. Utility and MIDI functions (Util. & MIDI menu) ......................................................................22

11. File management functions (File Manag. menu)........................................................................ 23

12. Playing and recording of musical sequences (Sequencer).........................................................24

12.1 Playing back a piece (Play mode) ............................................................................................................... 24

12.2 Recording a piece (Record mode) ............................................................................................................. 26

12.3 Sequencer playback options (Play Options menu).................................................................................. 28

12.4 Songlists (Songlist function)....................................................................................................................... 28

13. Appendix ......................................................................................................................................30

13.1 Stop Local Off ............................................................................................................................................. 30

13.2 Factory Settings............................................................................................................................................ 30

13.3 Upgrading the operating system ................................................................................................................ 31

Viscount UNICO 700 User Guide

1. IMPORTANT NOTES

1.1 LOOKING AFTER THE PRODUCT

• Do not apply excessive force to the organ’s structures or the controls (knobs, stops, push-buttons, etc.).

• When possible, do not place the instrument close to units which generate strong interference, such as

radios, TVs, computer videos, etc.

• Do not place the organ close to heat sources, in damp or dusty places or in the vicinity of strong magnetic

fields.

• Do not expose the instrument to direct sunlight.

• Never insert foreign bodies inside the instrument or pour liquids of any kind into it.

• For cleaning, use only a soft brush or compressed air; never use detergents, solvents or alcohol.

• Always use good quality screened cables for connection to amplification or diffusion systems. When

disconnecting cables from sockets, always take hold of the connector and not the cable itself; when

winding cables, do not knot or twist them.

• Before making the connections ensure that the other units (especially amplification and diffusion systems)

you are about to connect are switched off. This will prevent noisy or even dangerous signal peaks.

• Connect the net cable to an earthed socket.

• Check that the voltage corresponds to the voltage shown on the serial number plate of the organ.

• If the organ is to be out of use for lengthy periods, disconnect the plug from the power socket.

1.2 NOTES ABOUT THE MANUAL

• Take good care of this manual.

• This manual is an integral part of the instrument. The descriptions and illustrations in this publication

are not binding.

• While the instrument’s essential characteristics remain the same, the manufacturer reserves the right to

make any modifications to parts, details or accessories considered appropriate to improve the product or

for requirements of a constructional or commercial nature, at any time and without undertaking to

update this publication immediately.

specific written permission is forbidden.

• All the trademarks referred to in this manual are the property of the respective manufacturers.

Viscount UNICO 700User Guide

• Read all the information carefully in order to obtain the best performances from your product and waste

no time.

• The codes or numbers in square brackets ([ ]) indicate the names of the buttons, sliders, trimmers and

connectors on the instrument. For example, [ENTER] refers to the ENTER button.

• The illustrations and display pages are purely guideline and may differ from those actually shown on the

display.

• The instructions provided in this manual only concern the instrument's operating system version that

was up to date when the document was released. Therefore, such instructions might not describe faithfully

your current operating system release. Please, visit the website http://www.physisorgans.com/

download.asp to check for the newest operating system release and manual.

• Check the Reference Manual for detailed descriptions on the organ's functions. The manual can be

downloaded from the Download page of the website http://www.physisorgans.com.

Viscount UNICO 700 User Guide

2. INTRODUCTION

Dear Customer,

Thank you for choosing the organ Viscount

Unico. The Company, a world leader in the

construction of fine classical organs, has installed

in this instrument the latest and most sophisticated

technology dedicated to the high fidelity

reproduction of pipe organ sounds, with

impressive flexibility and remakable quality of

timbre.

After years of research exploring musical synthesis

techniques, our Research and Development unit,

is the FIRST in the world to create the sounds of

a pipe organ by using the “physical modeling

technology” upon which the Physis is based.

Instead of using “sound samples” from pipe

organs (previously the standard method) this

revolutionary sound generation system involves the

real-time calculation of the waveform generated

by a precise mathematical model based on the

sound emission physics of a pipe organ,

incorporating the principal physical parameters ie. construction geometry, materials used, and pertaining air

pressure, etc.

The fact that the simple reproduction of memorized “sound” has been disregarded, permits the achievement

of unimaginable realism, with the level of detail previously only created by a traditional pipe organ.

For example, the mathematical model allows the production of a different sound for each key since it provides

the virtual reproduction of the original instrument by assigning a different pipe to each note, similar to a pipe

organ. Furthermore, it will generate a different sound for each consecutive pressure of the same note, thus

simulating the precise condition of the air volume inside the pipe as it is pressed.

The Unico also permits the “physical” editing of the sounds produced, by adjusting the parameters - just as

the organ builder constructs the pipes. If however, “editing” is not your forte, you may choose your sound

from a big library of pre-programmed pipe organ voices already in the instrument’s memory.

To conclude we suggest that you visit our web-sites www.viscount-organs.com and www.physisorgans.com

where you will find information, updates, documents and news about our unique range of instruments.

Viscount UNICO 700User Guide

3. GENERAL DESCRIPTION

Viscount UNICO 700 User Guide

1. PEDAL Section.

Contains the pedal’s stops and couplers for linking the manuals to the pedal board.

2. MAN. II Section.

Contains the stops, manual couplers and tremulants of Manual II.

3. MAN. IV Section.

Contains the stops and tremulants of Manual IV.

4. MAN.III Section.

Contains the stops, manual couplers and tremulants of Manual III.

5. MAN.I Section.

Stops, manual couplers and tremulants for Manual I.

6. [POWER] Switch.

Instrument on/off switch.

7. AMPLIFICATION Section.

Organ amplification controls.

- [CONSOLE ON] switches on the instrument’s internal amplification system.

- [EXT. SPEAKER ON] enables the PROG. OUT external outputs in the rear panel (point 27).

8. CANCEL Section.

Cancel buttons which allow disabling of all the Reed voices ([REED] tab) and the Plenum voices

([MIXTUR] tab).

9. MIDI Section

These controls, provided for each manual and the pedal board, allow transmission of the note MIDI

codes on the MIDI [OUT] port to be enabled and disabled. All the instrument’s other MIDI messages

will continue to be transmitted, even with the MIDI control off.

10. Control and programming section.

Contains the buttons and display for viewing and programming all the instrument’s setup and sequencer

functions.

11. ORCHESTRA Section.

This section contains the organ’s Orchestra stops.

12. Additional displays.

- [CRESCENDO] shows the step currently reached by the [CRESCENDO] pedal (point 25)

- [M. BANK] displays the memory bank of the combinations (general and customised) selected using

the [MEM. BANK +] and [MEM. BANK -] pistons (point 20).

13. General pistons.

These pistons and foot pistons recall the general combinations of the memory bank selected using

[MEM. BANK +] and [MEM. BANK -] (point 20). These combinations can be modified; the procedure

for saving them is described in point 19.

[HR] restores the voice setup prepared in manual mode before a memory was recalled.

General combination sequencer controls are also provided, [PREV] in descending order, [NEXT.] in

ascending order.

Viscount UNICO 700User Guide

14. Pedal Board pistons.

This section contains the six pedal board combinations and the [HR] control for restoring the pedal

board voice setup prepared in manual mode before one of these combinations is recalled. These

combinations can be modified; the procedure for saving them is described in point 19.

15. Manual IV pistons.

Pistons of the dedicated combinations of Man.IV. [HR] for restoring the Man.IV voices setup prepared

in manual mode before one of these combinations is recalled. The combinations can be modified; the

procedure for saving them is described in point 19.

[P] of the IV/P coupling.

[M.SOLO] (MIDI Solo) piston, which allows mono transmission of the notes played on this manual on

the MIDI [OUT] output, with priority to the highest note.

16. Manual III pistons.

Pistons of the dedicated combinations of Man.III. [HR] for restoring the Man.III voices setup prepared

in manual mode before one of these combinations is recalled. The combinations can be modified; the

procedure for saving them is described in point 19.

[P] of the III/P coupling. [IV] of the keyboards coupling.

[M.SOLO] (MIDI Solo) piston, which allows mono transmission of the notes played on this manual on

the MIDI [OUT] output, with priority to the highest note.

17. Manual II pistons.

Pistons of the dedicated combinations of Man.II. [HR] for restoring the Man.II voices setup prepared in

manual mode before one of these combinations is recalled. The combinations can be modified; the

procedure for saving them is described in point 19.

[P] of the II/P coupling. [III], [I] and [IV] of the keyboards couplings.

[O.SOLO] (Organ Solo) pistons, which allow the Man.III voices to be played in mono mode with priority

to the highest note when the [III/II] coupling is active, and [M.SOLO] (Midi Solo) piston, which allows

mono transmission of the notes played on this manual on the MIDI [OUT] output, with priority to the

highest note.

18. Manual I pistons.

Pistons of the dedicated combinations of Man.I. [HR] for restoring the Man.I voices setup prepared in

manual mode before one of these combinations is recalled. These combinations can be modified; the

procedure for saving them is described in point 19.

[P] of the I/P coupling. [III] and [IV] of the keyboards coupling.

[M.SOLO] (MIDI Solo) piston, which allows mono transmission of the notes played on this manual on

the MIDI [OUT] output, with priority to the highest note.

19. [S] Piston.

Fixing piston for saving the general and dedicated combinations, the Tutti and the Crescendo steps.

To set a combination or the Tutti, after setting the voices as required, press [S], hold it down and then

press the piston or foot piston of the combinations you wish to save.

To save a Crescendo step, select it using the pedal of the same name, press [S], hold it down and press the

[HR] of the general memories. To copy the contents of one step into another, select the step you wish to

copy, hold down the [S] piston, select the step into which you wish to copy the contents, then press the

[HR] of the general memories.

NOTE

If the LED of the [S] piston is off, programming of the organ is locked out by the Lock Organ

function (chapt. 10), so it will not be possible to save combinations and/or view internal programming

functions.

Viscount UNICO 700 User Guide

20. Organ general controls.

These controls do not refer to individual sections but to the entire instrument.

- [MEM. BANK +] and [MEM BANK -]: they select the memory bank displayed by the additional

[MEM. BANK] display (point 12).

- [ENC]: enables the Enclosed function, which allows the organ’s general volume to be controlled

using the swell pedal [MAN.III].

- [A.P.]: enables the Automatic Pedal which allows the pedal voices to be played on Man.II. In this case,

the organ’s pedal board is deactivated and the voices become monophonic, with priority to the lowest

note.

- [T]: piston and foot piston for recalling the Tutti. The Tutti can be modified; the procedure for saving

it is described in point 19.

- [C]: Cancel piston

NOTE

Memory bank n. 1 is always selected when the instrument is switched on.

21. Front connections panel.

This panel, on the left underneath the manuals, contains the connectors and settings most often used, for

convenient access.

- [MASTER VOLUME]: regulates the organ’s general volume.

- [REVERB VOLUME]: regulates the level of the reverb effect.

- MIDI [IN]: the MIDI input connector for allowing the organ to receive the data transmitted by a

remote MIDI unit.

- MIDI [OUT]: the MIDI connector that transmits the MIDI data generated by the organ.

- MIDI [THRU]: retransmits the data received by the [IN] port for connection of several MIDI devices

in series.

- [USB]: two USB connectors. The one on the left is used for connecting to a computer to allow the

instrument’s setup programme to be used. The one on the right is for use of an USB stick (not

supplied with the instrument) for use as a mass memory for the organ instead of the internal memory.

For further information refer to chap. 11.

- [PHONES]: the socket for connecting a headphone set.

22. Cover lock.

23. Coupler toe-studs.

These pistons duplicate the functions of the piston and draw-stop couplers.

24. [32’ FLUTE REVERS.] toe-stud.

When activated, this piston can be used to turn off the 32’ flutes.

25. [CRESCENDO] sweller.

You can use this sweller to select the Crescendo steps which activate a preset series of stops. The step

currently selected is displayed by the additional [CRESCENDO] display (see point 12).

Each Crescendo step is programmable. The procedure for saving them is described in point 19.

26. Swell expression pedals.

The organ has three swell pedals for continuous control the expression of Manual I, Manual III and

Manual IV.

The [MAN.IV] swell pedal also incorporates a special lever system for control of the Sustain effect for

the Orchestra voices.

Viscount UNICO 700User Guide

27. Rear connections.

On the back of the organ, there are various connections for making the audio connection to external

speaker systems, and the line and microphone input for use of the organ’s internal amplifier.

- [EXT. +12V DC] connectors: power at +12 Volt can be obtained from these connectors to switch-

on any VISCOUNT speakers connected to the PROG. OUT. outputs.

- OUT [GEN. SUB] (General Sub-Woofer): dedicated output for the connection of low-frequency

speakers (sub-woofer).

- PROG. OUT (Programmable Outputs): the instrument’s general line outputs, allowing simulation of

the wind-chests of pipe organs. The signals are distributed over the outputs on the basis of the

display function settings, which allow setting of the type of wind-chest, its size and the position in

space of the speakers used, for each stop. Each output also has dedicated level and equalisation

controls.

- INPUT [L(+R)] / [R]: line inputs which allow other instruments to be played using the organ’s

internal amplification. If the source is monophonic use the [L+(R)] connector only.

- INPUT [MIC]: microphone input allowing amplification of the signal from a microphone.

- [GAIN]: trimmer for regulating the gain of the input signal received at the [MIC] connector.

WARNING!

This group of connections on the rear is not visible from the outside and the organ’s wooden rear

panel has to be removed to access it. Contact qualified staff for this procedure.

Viscount UNICO 700 User Guide

4. SWITCHING ON and MAIN VIDEO PAGE

After the instrument is switched on with the [POWER] switch, the system takes a few seconds to become

operational. During this stage, the LEDs on the separate panels of the manuals come on in sequence, and

the display shows the introductory screen.

When the main video page appears, the instrument is ready for use:

The top of this screen contains the fields for selecting the organ’s various setup menus:

o TUNING: instrument tuning parameters.

o VOICES: functions relating to all the organ’s voices.

o STYLE: style selection.

o SET-UP: organ general set-up functions

o UTIL. & MIDI (Utility & MIDI): utility and MIDI functions

o FILE MANAG. (File Manager): management of the files saved in the internal memory or the USB

device.

To display the contents of a menu, simply locate the cursor (the field on which it is located appears in reverse

mode) on the field required using the [FIELD S] and [FIELD T] buttons and press [ENTER]. [EXIT] quits

the menu and returns to the main video page.

The bottom of this screen displays the instrument parameters the status of which it is always useful to know:

o [box in top left-hand corner]: (Equal in the screen shown) displays the temperament currently in use,

selected in the TUNING menu.

o ENSEMBLE: the ENSEMBLE value set in the TUNING menu.

o AIR PRESS: the AIR PRESSURE parameter value set in the TUNING menu.

o A: the instrument’s tuning, expressed as the frequency of A4, set in the TUNING menu.

o [box in top right-hand corner]: (User2 in the screen shown) contains the style selected in the STYLE

menu.

o P. COMB: the status of the PISTON COMBINE function as set in the UTILITY & MIDI menu.

o K. INV: the status of the KEYBOARD INVERSION function as set in the UTILITY & MIDI menu.

o TRANSP: the transposition set in TUNING.

These fields are for information only and cannot be selected. The menus referred to above have to be

accessed to modify the setting of the relative function.

The buttons used to view and navigate through all the display screens are arranged around the display.

- [SEQUENC]: screens for use of the instrument’s internal sequencer.

- [VOLUMES]: screen containing all the instrument’s volumes.

Viscount UNICO 700User Guide

- [FIELD S] and [FIELD T]: buttons used to move the cursor, identified by the field in reverse.

[FIELD S] positions it in the field above or the previous field, [FIELD T] in the field below or the next

field.

- [VALUE +] and [VALUE -]: buttons which regulate the values of the parameters, whether they are

numerical or alphanumerical. [VALUE +] increases, [VALUE -] decreases.

- [EXIT] and [ENTER]: buttons for accessing and quitting the display screens and menus, or for

confirming or cancelling prompts made by the system. [ENTER] accesses menus/screens and confirms,

[EXIT] quits menus/screens and cancels.

5. SETTING THE VOLUMES

(VOLUMES function)

Pressing the [VOLUMES] button displays the screen relating to all the organ’s volume controls:

o MST (Master): the organ’s overall volume, which can also be adjusted with the [MASTER VOLUME]

trimmer underneath the manuals.

o REV (Reverb): reverb effect, which can also be adjusted with the [REVERB VOLUME] trimmer

underneath the manuals.

o PHO (Phones): level of the output signal at the headphone [PHONES] connector underneath the manuals.

o EXT (External outputs): general volume of the PROG. OUT connectors on the rear panel.

o PED (Pedal): pedal board divisional volume.

o II (Manual II): second manual divisional volume.

o III (Manual III): third manual divisional volume.

o I (Manual I): first manual divisional volume.

o IV (Manual IV): fourth manual divisional volume.

o ORC (Orchestra): volume of the orchestra section.

Press [EXIT] or wait about 4 seconds to quit the screen and return to display of the previous video page.

Viscount UNICO 700 User Guide

6. TUNING THE INSTRUMENT

(TUNING menu)

Selecting the TUNING field on the main video page gives access to all the instrument’s tuning parameters.

o TRANSPOSER: transposer with a range from -6 to +5 semitones. When switched on, the organ always

has transposition equal to zero.

o [second field on the display]: (Equal in the screen shown) selector for setting historic temperaments

of various periods and countries of origin.

o BASE KEY: the note on which the chain of the 12 fifths that make up the temperament starts.

o ENSEMBLE: level of natural tiny differences in pitch between one organ pipe and another, simulating

the tuning error that occurs in the organ’s pipes due to wear over time and variations in temperature.

The values range from – (pipes perfectly tuned) to 8 (maximum pitch instability).

o AIR PRESSURE: simulates the drop in air pressure when a large quantity of air is requested in a short

time (e.g. when large chords are played with the Tutti). This is reflected in a temporary, gradual drop in

pitch, more obvious in the longest, widest pipes (flutes, bourdons, principals).

o PITCH (A): fine tuning of the pitch, indicated as the frequency of A4 (an 8’ pipe).

To quit the video page press [EXIT].

NOTE

Transposition does not have any effect on playback of pieces with the internal sequencer (unlike

recording, where the notes are acquired transposed). A specific transposer is provided for this

purpose (see point 12.3).

Viscount UNICO 700User Guide

7. THE ORGAN STYLES

(STYLES menu)

The Style identifies the setup of the organ stops, meaning the voice and the relative parameters of each stop,

allowing the use of sounds appropriate to the repertoire to be performed.

The organ has eight Styles, meaning eight sound setups, in the same console. The first four of them, which

from now on we will also call the Presets or preset styles, are programmed by our laboratories on the basis of

the appropriate organ schools, and cannot be modified by the user. The other four Styles, called User styles,

can be freely modified and customised to personal taste, making the organ extremely flexible.

Select the STYLE field on the main page for the Style selection:

As we have already stated, the first four Styles cannot be modified, so accessing to the VOICES function the

display shows the following warning message:

However it is possible to display and check the settings of these Styles, to continue press any display button

or wait about three seconds.

Viscount UNICO 700 User Guide

8. SELECTING AND REGULATING THE VOICES

(VOICES menu)

One of the main features of the new Physis synthesis technology used by the Unico organs for sound

generation is that it offers the user a wide array of options for personalising the instrument with a very large

number of organ timbres, and also makes available several parameters which can be adjusted to further

increase the setup potential.

The VOICES menu contains all the functions for selecting and regulating the voices’ audio parameters.

NOTES:

- The functions described below cannot be edited when a Preset style is selected. Select a User

style to regulate these parameters.

- The voices selected for each rocker switch or draw-stop, and the sound generation parameters

and volume, are automatically saved in the current Style. This means that when another style is

recalled, the voices will be reset with new parameters taken from the last style recalled. The

changes made earlier are not lost, and will be made available when the style in which they were

made is selected again.

The first video page displayed allows selection of the function to be accessed:

o VOLUME LEVEL: regulation of the volume of each individual voice.

o EDIT PARAMETERS: regulation of the sound generation parameters for each individual voice.

o ALTERNATIVE VOICES: selection of alterative voices.

8.1 REGULATING THE VOLUME (VOLUME LEVEL function)

After the VOLUME LEVEL field has been selected in the VOICES menu, the display shows the organ

sections. Select the section which contains the voice the volume of which you wish to adjust:

Viscount UNICO 700User Guide

As usual, use the [FIELD S] and [FIELD T] and [ENTER] buttons to select the field on the display.

Another way of displaying and adjusting the volume immediately is to hold out the draw-stop or hold down

the rocker tab for a few moments in the voice on position with the cursor on the VOLUME LEVEL field in

the VOICES menu, or in the function itself.

The LED of the stop the volume of which is being adjusted will flash to prevent modification errors; the

stop will be on and can be played for better, quicker adjustment. Other stops can also be switched on to

assess the overall effect of the changes.

To quit the function and save the values press [EXIT].

8.2 REGULATING THE AUDIO PARAMETERS (EDIT PARAMETERS function)

To view the screens containing the sound generation parameters of each individual voice, select the EDIT

PARAMETERS field in the VOICES menu:

For this function the display again shows the organ’s sections, allowing selection of the one containing the

voice to be modified.

after which the voice the parameters of which are to be viewed can be displayed.

Another way of viewing the setting screen directly is to hold out the draw-stop or hold down the rocker tab

for a few moments in the voice on position with the cursor on the EDIT PARAMETERS field in the

VOICES menu, or in the function itself.

Viscount UNICO 700 User Guide

The LED of the stop being modified will flash to prevent modification errors; the stop will be on and can be

played for better, quicker adjustment. Other stops can also be switched on to assess the overall effect of the

changes.

The parameters displayed are not the same for every voice, since some families have specific setting parameters

not required for other types of voice.

The settings which can be made are:

o CHARACTER: harmonic richness.

o AIR NOISE: noise of the air blowing through the pipe.

o REED NOISE: imperfect synchronisation of the reed throb period.

o ATTACK: attack time the sound takes to reach the maximum volume.

o REL. DETUNE: (Release Detune) detuning in the release phase.

o FREQ. SKEW: gradual change in the air’s pitch during the attack and release phases.

o DETUNE: detuning to produce the throb effect in the voices concerned.

o KEYB. LO LEV.: (Keyboard Low Level) gain (positive values) or attenuation (negative values)of the

volume in the low part of the manual.

o KEYB. LO LEV.: (Keyboard High Level) gain (positive values) or attenuation (negative values)of the

volume in the high part of the manual.

o TREMULANT: select the first (1st) or second (2nd) tremulant. The selected tremulant will be applied

to the register when activated through the dedicated draw-stop.

To quit the function and save the values press [EXIT].

8.3 SELECTING THE ALTERNATIVE VOICES (ALTERNATIVE VOICE

function)

Each stop on the panel has a set of voices, the default voice set by the current Style and the alternative voices,

which are variants on the original. To select an alternative voice, the ALTERNATIVE VOICES function has

to be recalled:

As for the other VOICES menu functions, the next step is to select the section of the organ containing the

voice to be modified: this displays the list of the voices present in the chosen section.

Viscount UNICO 700User Guide

Here again, there is the option of displaying the alternative voices screen directly by holding out the draw-

stop or holding down the rocker rab for a few moments in the voice on position with the cursor on the

ALTERNATIVE VOICES field in the VOICES menu, or in the function itself.

The LED of the stop being replaced will flash to prevent modification errors; the stop will be on and can be

played for better, quicker adjustment.

The display now shows the list of the alternative voices:

identified as “CURRENT VOICE” in the bottom of the screen.

It should also be remembered that the top of the screen always contains the name screen-printed on the

draw-stop or tab, so that the stop the voice of which is being changed can be identified at all times.

When the [FIELD S] and [FIELD T] buttons are used to move the cursor to other voices, the prompt

changes to “ENTER TO REPLACE”.

instructing you to press [ENTER] to confirm the new voice and render it usable. The voice on which the

cursor is located is available and can be played even before [ENTER] is pressed, allowing the modification

required to be evaluated immediately. Other stops can also be switched on to assess the overall effect of the

changes.

Press [EXIT] to replace other voices or exit the function.

NOTE:

When an alternative voice is selected, the sound generation parameters in the EDIT PARAMETERS

function are automatically reset to the default values of the new voice. The volume setting (in the

VOLUME LEVEL function) remains unchanged.

Viscount UNICO 700 User Guide

9. INSTRUMENT GENERAL SETTINGS

(SET-UP menu)

The SET-UP menu contains all the instrument’s general settings except for the settings relating to the MIDI

interface and the accessory and utility functions. To recall this menu, select the SET-UP field from the main

video page:

The functions available are as follows:

o 1st TREMULANT: setting of the first tremulant speed and depth for each individual manual.

o 2nd TREMULANT: setting of the second tremulant speed and depth for each individual manual.

o REVERBERATION: selection of the type of room for the reverb effect.

o INT. AMPL. EQUALIZER (Internal amplification equalizer): setting of the 5-band equalizer of the

internal amplifier.

o INT. AMPL. PANNING (Internal amplification panning): setting of the stereophonic distribution of

the stops of the internal amplification system, to simulate different types of wind- chests for the various

stops.

o INT. AMPL. TUNE-UP (Internal amplification tune-up): function not available in these models.

o PROG. FUNCTIONS (Programmable functions): settings relating to operation of the combinations,

the pistons, the Crescendo and the trimmers underneath the manuals.

o ENC. CONFIGURATION (Enclosed configuration): program the [ENC] piston function .

o EXT. OUT EQUALIZER (External outputs equalizer): setting of the equalizers of the PROG. OUT

outputs on the rear.

o EXT. SUB EQUALIZER (External sub equalizer): equalizer adjustment for the external output on the

back [GEN. SUB.].

o EXT. OUT ROUTER (External outputs router): setting of the routing of the stops on the PROG.

OUT outputs on the rear to simulate the position of the wind-chests and the arrangement of the pipes

inside them.

o EXT. OUT VOLUME (External outputs volume): setting of the volumes of the PROG. OUT outputs

on the rear.

o EXT. OUT CONFIG (External outputs config): setting of the PROG. OUT rear outputs.

o EXT. OUT RESIZE (External out resize): Adapts automatically the link between stops and rear

outputs, according to the amount of outputs actually used.

La pagina sta caricando ...

Viscount Unico 700 Manuale utente

Marca: Viscount

Modello: Unico 700

Categoria: Apparecchiature musicali supplementari

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Viscount Unico 700 User manual
Nederlands: Viscount Unico 700 Handleiding

Viscount Unico 700 Manuale utente

Viscount Unico 700 Manuale utente

in altre lingue

Documenti correlati

Altri documenti