Sanyo POAMD07MCI - Digital AV Player Install And Operation Instructions

Français

Español

Deutsch

Italiano

English

Media Card Imager Kit

MODEL POA-MD07MCI

INSTALLATION AND OPERATION

OF THE IMAGER BOX

This Media Card Imager kit is an optional

kit to project image data in various format

and files created with Microsoft PowerPoint

with our projector. Image data can be easi-

ly projected just by attaching the Imager

Box to a projector without any connection

with a computer.

This kit is only used for our projectors that

have a terminal for the Imager Box.

This manual explains the installation of the

Imager Box and its operation.

The data played back through the Imager

Box is edited with Media Card Imager soft-

ware included in the kit. For operation of

the software, refer to separately included

"Media Card Imager" Owner's Manual.

OWNER'S MANUAL

2

Compliances

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generated, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures :

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Trademark

Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corp. in

the U.S.A.

Microdrive is a trademark of IBM in the U.S.A.

CompactFlash is a trademark of SanDisk Corporation in the U.S.A.

Each name of corporations or products in Owner's Manual is a trademark or a regis-

tered trademark of its respective corporation.

Do not make any changes or modifications to the equipment unless otherwise speci-

fied in the manual. If such changes or modifications should be made, you could be

required to stop operation of the equipment.

3

English

Table of Contents

Table of Contents 3

Contents of Media Card Imager Kit 3

Name of Each Part of Imager Box 4

Attach Imager Box to Projector 5

Remove Imager Box from Projector 6

Load and Remove CF Card 6

Use CF Card Adapter 7

Handle CF Card and Adapter 8

Specifications 9

PLAY BACK IMAGE

(OPERATING PROJECTOR) 11

PLAYING BACK IMAGE IN THE MEMORY CARD

11

PICTURE IMAGE ADJUSTMENT

15

PICTURE SIZE ADJUSTMENT

17

Contents of Media Card Imager Kit

The package contains following items. Make sure you have all of it.

Imager Box

CompactFlash

(CF) Card

CF Card Adapter

Media Card Imager Kit

Owner's Manual (this

manual)

* CD-ROM * MediaCard Imager

Owner's Manual

*Those are used for editing image data played back with the Imager Box.

4

Name of Each Part of Imager Box

Imager Box

LATCH

BUTTON

CF CARD EJECT

BUTTON

MOUNTING HOOK

SWITCH

BUTTON

CONNECTOR

PLUG

CF CARD SLOT

INDICATOR

(lights while

accessing)

5

English

Attach Imager Box to Projector

CAUTION : Turn off the projector when attaching the Imager Box to the projector.

Do not attach or remove while the projector is turned on. It may damage

the equipment.

Remove 4 covers attached to a projector. Insert the

MOUNTING HOOKs (A) into the projector to the arrow

direction. (Fig.-1)

1

2

Plug the CONNECTOR PLUG into the DVI Terminal of the

projector while pressing the Imager Box LATCH BUTTON,

and release it.

C

O

M

P

U

T

E

R

IN

D

IG

IT

A

L

MCI

S – VIDEO

R – AUDIO IN – L

VIDEO

Y – Pb / Cb – Pr / Cr

CONTROL PORT

USB

COMPUTER IN

ANALOG

AUDIO IN

COMPUTER

R – – L

AUDIO OUT

(MONO)

(Fig.-1)

(Fig.-2)

(A)

LATCH BUTTON

The SWITCH BUT-

TON of the Imager

Box is placed on

the switch of the

projector.

CONNECTOR

PLUG

DVI Terminal

Remove 4 covers.

cover

6

Remove Imager Box from Projector

Press the LATCH BUTTON to the arrow

direction. Then pull and remove the

Imager Box.

CAUTION:Removing by force may

damage the Imager Box.

(Fig.-3)

Press the LATCH

BUTTON.

CAUTION : Do not remove the Imager Box from the projector while the projector is

on. It may damage data in a memory card and the card itself.

Load and Remove CF Card

Load CF Card

(Fig.-4)

CF CARD

EJECT BUTTON

INDICATOR

1

2

Insert the CF Card into the CF Card slot

of the Imager Box until the EJECT BUT-

TON pops out.

• Do not insert it in the wrong way. It may damage

the equipment.

Remove CF Card

Press the CF CARD EJECT BUT-

TON. The CF Card is released.

Pull out the CF Card from the Imager

Box.

Do not remove a CF Card while

the indicator is lighting. It may

damage the card and the data

in it.

CAUTION

Insert the CF Card with the

mark

▲ ahead.

Pull and remove the

Imager Box.

7

English

Use CF Card Adapter

CF Card Adapter is used when a CF Card is loaded into the PC card slot of a com-

puter. You can write and rewrite data into the CF Card with the Adapter through the

PC card slot of a computer. For operation, refer to the "Media Card Imager" Owner's

Manual.

Attach CF Card

Insert the CF Card firmly into the CF Card

Adapter, aligning the arrows on the CF

Card and the adapter.

Remove CF Card

Pull the CF Card straight out.

Insert the CF Card aligning the arrows.

IMPORTANT NOTE

Data stored on a CF Card may be damaged or lost due to physical damage to

the CF Card or accidental erasure. It is recommended that any important data

should be copied as a backup onto separate media, such as a floppy disk, a

hard disk, or a MO disk, etc. We shall not be liable for any damage or loss of

profits arising from the loss of data caused by the misoperation or the damage to

a CF Card or its appliances.

The following may result in damaged or lost data:

• Misoperation of the CF Card.

• Turning off the projector or the computer or removing the CF Card / Adapter

while the CF Card is in access operations (writing, reading, or deleting the

files).

• Exposure to a strong static electric charge.

• The CF Card has reached the end of its life.

CF Card

CF Card Adapter

8

Handle CF Card and Adapter

● CF Cards / Adapters are high-precision electronic devices. Do not bend, drop,

apply strong forces or shock or place it where a strong static electrical charge may

be generated.

● Do not touch the surface of the contact area with your fingers or allow it to be

stained with foreign materials.

● Do not attempt to disassemble or alter CF Cards.

● Moving CF Card rapidly between hot and cold temperatures may cause conden-

sation (water droplets) to form on it, leading to malfunctions. Avoid this problem

by placing the CF Card in a plastic bag and letting it slowly adjust to temperature

changes before removing it from the bag. If condensation should occur, maintain

the CF Card at a constant temperature and let the moisture evaporate naturally.

● Store CF Cards / Adapters in the protective case.

● Do not use or store CF Cards / Adapters in places subject to the following condi-

tions:

• strong magnetic fields

• abundant dirt or dust

• high temperatures, high humidity

ENVIRONMENT of CF Card operation

Operating Temperature : 41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

Storage Temperature : 14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

9

English

Dimensions

(W x H x D)

Weight

Operating Voltage

Available Memory

Card

4.61" x 2.76" x 0.75" (117mm x 70mm x 19mm)

(not including MOUNTING HOOKs)

5.29 oz (150g)

DC 5V 450mA, DC 3.3V 600mA

We recommend you to use a CF card that comes with

this kit. The following memory cards can also be used.

• Microdrive (1GB or less)

We do not guarantee use of any memory card except for

the above. Some memory cards may not operate properly.

Specifications

■ Imager Box

■ CompactFlash Card Adapter (ATA standard

Type-

II)

NOTE ; This adapter cannot be used for other memory cards.

The specifications are subject to change without notice.

■ CompactFlash (16MB)

10

English

11

IMAGE PLAYBACK (OPERATING PROJECTOR)

Attach Imager Box to your projector properly (P5), and turn the projector on. Refer to Owner’s Manual

of your projector for operation.

1

2

Load a memory card into CF Card Slot of Imager Box. (P6)

NOTE ; Refer to Owner’s Manual of your projector for location of each button and basic operation.

3

Projector automatically turns to MCI mode and shows the image data in a memory card.

PLAYING BACK IMAGE IN THE MEMORY CARD

MENU BAR

Used to select

input source

either Computer

(MCI) or Video.

(Refer to P12)

INPUT MENU

Used to select image

level among Standard,

Real and Image 1 ~ 4.

(Refer to P15)

IMAGE SELECT MENU

Used to adjust size

of image to Normal

or True, or expand /

compress image

(Digital zoom +/–).

(Refer to P17)

SCREEN MENU

Used to change settings

of projector or reset Lamp

Reset Counter.

(Refer to Owner’s Manual

of your projector.)

SETTING MENU

Used to display

image data in a

memory card.

(Refer to P13, 14)

VIEW MENU

Used to adjust picture image.

[Contrast / Brightness / White

balance (Red/Green/Blue) /

Gamma]

(Refer to P16)

IMAGE ADJUST MENU

Used to adjust volume

or mute sound. (Refer

to Owner’s Manual of

your projector.)

SOUND MENU

Press MENU button while in MCI mode.

Shows selected

item of ON-

SCREEN Menu.

GUIDE WINDOW

12

IMAGE PLAYBACK (OPERATING PROJECTOR)

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT button

to move a red frame pointer to INPUT Menu

icon.

1

2

Press POINT DOWN button to move a red

arrow pointer to Computer and then press

SELECT button. Source Select Menu will

appear.

Move a pointer (red arrow)

to Computer and press

SELECT button.

INPUT MENU

INPUT Menu icon

Choose Computer by pressing INPUT button on

Top Control or on Remote Control Unit.

If projector cannot reproduce proper image, select

correct input source through MENU OPERATION.

INPUT button

Computer

Video

Source Select Menu

Move a pointer to MCI

and press SELECT

button.

SELECTING INPUT SOURCE

DIRECT OPERATION

MENU OPERATION

INDEX AND PAGE

Image data edited with Media Card Imager

(software) is Index format consisting of several

Pages. To project desirable image, select Index

and then select Page in the Index.

When a memory card is loaded into Imager Box connected to the projector, MCI mode is

automatically selected. The first Page of the latest Index in a memory card is displayed on a

screen.

To switch to MCI mode manually, operate as follows.

Quit

Closes Source Select Menu.

Select Index

Index

Pages in Index

3

Move a pointer to MCI and then press SELECT

button.

English

13

IMAGE PLAYBACK (OPERATING PROJECTOR)

To project desirable image, select Index and then Page as follows.

SELECTING INDEX

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT button

to move a red frame pointer to VIEW Menu

icon.

1

2

Press POINT DOWN button to move a red

frame pointer to Index icon and then press

SELECT button. The table of Indexes in the

memory card is displayed.

Press RIGHT CLICK button on Remote Control

Unit to stop table display. (✽1)

Move a red frame pointer to Index

icon and press SELECT button.

VIEW MENU

VIEW Menu icon

Press POINT LEFT/RIGHT/UP/DOWN buttons

to move a pointer to the Index to be projected

and then press SELECT button. The first Page

of the selected Index is displayed.

Press POINT UP/DOWN button to turn

previous/next Page over. (✽2)

POINT UP button ··· returns to previous page.

POINT DOWN button ··· goes to next page.

3

SELECTING PAGE

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT button

to move a red frame pointer to VIEW Menu

icon.

1

2

Press POINT DOWN button to move a red

frame pointer to Page icon and then press

SELECT button. The table of all Pages of

selected Index is displayed.

Press RIGHT CLICK button on Remote Control

Unit to stop table display. (✽1)

Press POINT LEFT/RIGHT/UP/DOWN buttons

to move a pointer to the Page to be projected

and then press SELECT button.

Press POINT UP/DOWN button to turn

previous/next Page over. (✽2)

POINT UP button ··· returns to previous page.

POINT DOWN button ··· goes to next page.

Table of Pages can be also displayed by

pressing SELECT button when Page is

displayed on full screen.

3

Move a red frame pointer to Page

icon and press SELECT button.

VIEW MENU

VIEW Menu icon

✽1 When RIGHT CLICK button is

pressed during table display, each

Index/Page is displayed as an icon.

This operation reduces time for

displaying all image data.

✽2 When ON-SCREEN MENU is

displayed, Page cannot be turned

over to next/previous one.

14

IMAGE PLAYBACK (OPERATING PROJECTOR)

AUTO PLAY FUNCTION

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT button

to move a red frame pointer to VIEW Menu

icon.

1

2

Press POINT DOWN button to move a red

frame pointer to Auto play icon and then press

SELECT button. Auto play setting dialog box

will appear

3

Auto play setting dialog box

Press POINT LEFT/RIGHT

button(s) to adjust the interval

and press SELECT button.

VIEW MENU

VIEW Menu icon

Quit

Closes Auto play setting dialog box.

When setting Auto play function on, move a red

arrow pointer to “On,” adjust interval (sec.) by

pressing POINT LEFT RIGHT button, and then

press SELECT button. Projected image is

turned over to next automatically with interval.

This Auto play function can be pausing by

pressing POINT UP button and restarts with

POINT DOWN button.

✽ When auto play setting is previously set with

Media Card Imager (software), interval set by

Media Card Imager has priority over interval

with this menu.

On

To cancel Auto play function, move a red arrow

pointer to “Off” and then press SELECT button.

Auto play setting set with Media Card Imager

(software) is also suspended by setting to “Off.”

Off

Do not remove a memory card from Imager Box while Auto play function is

operated or Indicator of Imager Box is lighting or flashing. It may damage a

memory card or data in a memory card.

Before removing a memory card from Imager Box, be sure to set Auto play

function to “Off” or interrupt input signal from Imager Box by changing input

source.

CAUTION

English

15

IMAGE PLAYBACK (OPERATING PROJECTOR)

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (MENU OPERATION)

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT button

to move a red frame pointer to IMAGE SELECT

Menu icon.

1

2

Press POINT DOWN button to move a red

frame pointer to the Image Level that you want

to set and then press SELECT button.

Move a red frame pointer to the

Image Level and press SELECT

button.

Image Level being selected.

IMAGE SELECT MENU

Normal picture level preset on this projector.

Standard

Picture level with improved halftone for graphics.

Real

User preset picture adjustment in IMAGE ADJUST

Menu (refer to P16).

Image 1 ~ 4

IMAGE SELECT

Menu icon

IMAGE LEVEL SELECT (DIRECT OPERATION)

Select Image Level among Standard, Real, Image

1, Image 2, Image 3 and Image 4 by pressing

IMAGE button on Top Control or on Remote

Control Unit.

IMAGE button

Standard

Real

Image 1

Image 2

Image 3

Image 4

Normal picture level preset on this projector.

Picture level with improved halftone for graphics.

User preset picture adjustment in IMAGE ADJUST

Menu (refer to P16).

Standard

Real

Image 1 ~ 4

16

IMAGE PLAYBACK (OPERATING PROJECTOR)

IMAGE LEVEL ADJUSTMENT

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT

buttons to move a red frame pointer to IMAGE

ADJUST Menu icon.

1

2

Press POINT DOWN button to move a red

frame pointer to the item that you want to

adjust, and then press SELECT button. The

level of each item is displayed. Adjust each

item by pressing POINT LEFT/RIGHT buttons.

Move a red frame pointer to

the item to be adjusted and

then press SELECT button.

IMAGE ADJUST MENU

IMAGE ADJUST

Menu icon

Selected Image Level (P15)

Press POINT LEFT/RIGHT

buttons to adjust value.

IMAGE LEVEL SET MENU

Move a red frame pointer to

Image 1 ~ 4 and then press

SELECT button.

Store icon

Press SELECT button at this icon

to store the adjustment.

Press POINT LEFT button to decrease contrast,

and POINT RIGHT button to increase contrast.

(From 0 to 63.)

Contrast

Press POINT LEFT button to adjust image darker,

and POINT RIGHT button to adjust brighter. (From

0 to 63.)

Brightness

Press POINT LEFT button to lighten tone of each

color, and POINT RIGHT button to deepen tone.

(From 0 to 63.)

White balance (Red/Green/Blue)

Press POINT LEFT button or POINT RIGHT button

to obtain better balance of contrast. (From 0 to 31.)

Gamma

Store

To store manually preset image level, move a

red frame pointer to Store icon and press

SELECT button. IMAGE LEVEL SET MENU

will appear. Move a red frame pointer to Image

1 ~ 4 where you want to set and then press

SELECT button.

3

Reset

Reset all adjustment to previous value.

Quit

Closes IMAGE ADJUST MENU.

English

17

IMAGE PLAYBACK (OPERATING PROJECTOR)

PICTURE SIZE ADJUSTMENT

Press MENU button and ON-SCREEN MENU

will appear. Press POINT LEFT/RIGHT

buttons to move a red frame pointer to

SCREEN Menu icon.

1

2

Press POINT DOWN button and move a red

frame pointer to the function that you want to

select and then press SELECT button.

This projector has a picture screen resize function, which enables you to display the desirable

image size.

Move a red frame pointer to the

function and press SELECT button.

SCREEN MENU

Provides image to fit screen size.

Normal

Provides image in its original size. When the

original image is larger than screen size, the

projector automatically enters “Digital zoom +”

mode.

True

When Digital zoom + is selected, ON-SCREEN

MENU disappears and the message “D. Zoom +” is

displayed. Press SELECT button to expand image

size. And press POINT UP/DOWN/LEFT/RIGHT

button(s) to pan the image. Panning function can

work only when the image is larger than screen

size.

Projected image can be also expanded by pressing

D. Zoom ▲ button on Remote Control Unit.

Digital zoom +

SCREEN Menu

icon

When Digital zoom – is selected, ON-SCREEN

MENU disappears and the message “D. Zoom –” is

displayed. Press SELECT button to compress

image size.

Projected image can be also compressed by

pressing D. Zoom ▼ button on Remote Control

Unit.

Digital zoom –

To cancel Digital Zoom +/– mode, press any button

except D. ZOOM ▲ /▼ , SELECT, POINT and

LASER buttons.

18

Kit de puce Media Card Imager

MODELE POA-MD07MCI

INSTALLATION ET UTILISATION

DE L’IMAGER BOX

Ce kit de puce Media Card Imager est un

kit en option permettant de projeter les

données d’images en différents formats et

fichiers créés par Microsoft PowerPoint

avec notre projecteur. Les données

d’images peuvent être projetées aisément

en fixant simplement l’Imager Box sur un

projecteur sans effectuer aucune connexion

à un ordinateur.

Ce kit est utilisé uniquement sur nos

projecteurs équipés d’une borne pour

l’Imager Box.

Le présent manuel donne les explications

relatives à l’installation et à l’utilisation de

l’Imager Box.

Les données lues par l’Imager Box sont

éditées par le logiciel de Media Card

Imager inclus dans le kit. Pour l’utilisation

du logiciel, reportez-vous au manuel du

propriétaire du “Media Card Imager” inclus

séparément.

MANUEL DU PROPRIETAIRE

Français

2

Conformité aux normes

Avis de la commission fédérale des communications

Cet appareil a été testé et jugé conforme aux limites des appareils numériques de la

classe B, conformément à l’article 15 des jugements FCC. Ces limites sont destinées

à assurer une protection raisonnable contre les interférences nuisibles dans une

installation résidentielle. Cet appareil produit, utilise et peut émettre de l’énergie de

fréquence radio, et s’il n’est pas installé et utilisé conformément aux instructions, il

pourra produire des interférences affectant négativement les communications radio.

Toutefois, il n’est pas garanti qu’aucune interférence ne se produira pas dans une

installation particulière. Si cet appareil cause des interférences affectant

négativement la réception des émissions de radio et de télévision, ce qui peut être

déterminé en éteignant et en rallumant l’équipement, nous conseillons à l’utilisateur

d’essayer de corriger les interférences en prenant une ou plusieurs des mesures

suivantes:

– Modifier l’orientation de l’antenne de réception, ou la placer à un autre endroit.

– Eloigner l’équipement du récepteur.

– Brancher l’équipement à une prise sur un circuit différent de celui auquel le

récepteur est connecté.

– Demander de l’aide au revendeur ou à un technicien de radio/télévision

compétent.

Marques de commerce

Microsoft, Windows et PowerPoint sont des marques déposées de la société

Microsoft Corp. des Etats-Unis.

Microdrive est une marque commerciale de la société IBM des Etats-Unis.

CompactFlash est une marque commerciale de la société SanDisk Corporation des

Etats-Unis.

Chaque nom de société ou de produit figurant dans le manuel du propriétaire est une

marque commerciale ou une marque déposée de sa société respective.

N’effectuez aucun changement ou modification sur cet appareil qui ne soit pas

expressément spécifié dans ce manuel. Si vous effectuez de tels changements ou

modifications, on pourra vous interdire d’utiliser cet appareil.

La pagina sta caricando ...

Sanyo POAMD07MCI - Digital AV Player Install And Operation Instructions

Sanyo POAMD07MCI - Digital AV Player Install And Operation Instructions

in altre lingue

Documenti correlati

Altri documenti