Paradyne 6512-A2 Installation Instructions Manual

Marca
Paradyne
Modello
6512-A2
Tipo
Installation Instructions Manual
TM
1
SuperLine Integrated Access Device
Model 6512-A2
Installation Instructions
Document Number 6512-A2-GN10-30
May 1999
TST
LINE
ALMPWR
ETHERNET
TM
TM
98-16014a-02
BASE
PHONE
Rear
View
Front
View
SuperLine
TM
IAD
Contents:
What Your SuperLine Integrated Access Device (IAD) Does
Package Checklist
Optional Hardware (Not Supplied)
Front Panel Indicators
SuperLine IAD Rear Panel
Installing Your SuperLine IAD
Troubleshooting Your SuperLine IAD
Technical Information
Technical Specifications
Technical Support
Important Safety Instructions
2
What Your SuperLine Integrated Access Device
(IAD) Does
Your SuperLine IAD is a line adapter that allows you to connect multiple phones, fax
machines, or modems using your existing telephone wiring.
99-16257
TST
LINE
ALMPWR
ETHERNET
TM
TM
Existing
Phone Line
Existing (BASE) Phone
Additional Line (PHONE 1/2)
Additional Line (PHONE 2)
Ethernet Data
The SuperLine IAD:
Transforms your existing single phone line into multiple phone lines to support up
to two additional phones, fax machines, or modems simultaneously.
Operates over your existing copper wire with your existing telephone jacks.
Allows V.90 modem connections on your additional lines.
Provides high-speed Internet access through an Ethernet connection. (Available in
some areas. Ask your service provider about availability of this service.)
Only operates with Touch Tone phones. The PHONE 1/2 and PHONE 2 jacks do
not support pulse dial phones. (Your existing phone, plugged into the BASE
PHONE jack, can be a pulse dial phone.)
NOTE:
Your service provider must enable these services and assign phone numbers to
the additional phone lines before your SuperLine IAD will work.
The SuperLine IAD connects to your existing phone line to provide up to two additional
phone lines. These additional lines support any combination of up to two phones, fax
machines, or modems. Your SuperLine IAD also allows V.90 modem speeds with an
International Telecommunications Union (ITU) V.90 standard modem. The following
figure depicts a typical home or small office configuration with several existing phones
and two additional lines. Phone filters are connected to your existing phones to reduce
the amount of interference generated during phone conversations.
3
99-16018a-02
Wall
Jack
SuperLine
IAD
Wall
Jack
Phone
Filter
Phone
Filter
Existing
Phone
Line
Existing
Phone
Line
Existing
Phone
Line
Additional
Line
Additional
Line
Package Checklist
Verify that your package contains the following hardware. If any hardware is missing or
you need to order additional hardware, contact your service provider. Refer to
Technical
Information
on page 23 for further information.
SuperLine
IAD
6' RJ11
Phone
Cable
AC Power Transformer
(037-0118-0031)
99-16015a-02
Phone Filter
(6035-A1-002)
TST
LINE
ALMPWR
ETHERNET
TM
TM
LINE
PHONE
geprufte
Sicherheit
R
LR92997
TM
TUY
PRODUCT SERVICE
Phone Filter
P/N 0802-3392-00
Made in China / Fabriquè China
Bel Fuse Inc. 1198
ACCESSARY
L.T.E. EQUIPMENT
E100296
98-16067a
Pin #1
Pin #6
98-16051a
4
Optional Hardware (Not Supplied)
The following hardware may be required depending on which configuration you choose
to install. You can purchase these items from your local electronics or phone store.
2-Line Phone Cable (RJ14C)
If you are connecting a 2-line phone, you may
require a 2-line phone cable (24 AWG, RJ14C)
as defined in
Connecting a 2-Line Phone (with Two
Additional Lines)
on page 12. Refer to
Technical
Information
on page 23 for the 2-line phone
cable pin configuration.
“T” Type Connector
If your home or office phone jacks are wired
internally with 4 wires, you may be able to connect
phones in other rooms to your SuperLine IAD
using a “T” type connector as defined in
Optional
Configuration
on page 16. Refer to
“T” Type
Connector
on page 25 for the “T” type
connector pin configuration.
Do not use a “T” type connector to connect two
SuperLine IADs to a single wall jack.
5
Front Panel Indicators
99-16016a-01
Power – Green
Alarm – Red
Test – Yellow
Line – Green
Ethernet – Green
TST
LINE
ALMPWR
ETHERNET
TM
TM
All of the SuperLine IAD’s indicators turn ON and OFF during the power-on self-test.
After a successful power-on self-test, the SuperLine IAD’s indicators should appear as
indicated in BOLD in the Condition column of the following table:
Indicator Condition Status
PWR ON Power is applied to the SuperLine IAD.
ALM OFF
ON
No active alarms.
An alarm condition exists which may require further
attention. Refer to
Troubleshooting Your SuperLine IAD
on page 21.
TST OFF
ON
No active tests.
The TST indicator is ON during the power-on self-test and
during testing or upgrades initiated by your service
provider. Additional lines are not available when the TST
indicator is ON. Your existing (BASE) phone still works.
LINE ON
OFF
Your SuperLine IAD is connected to your local phone
company and is ready to use.
The link has not been established.
ETHERNET ON
OFF
The Ethernet connection to your PC or Ethernet Hub is
made and your PC is ON.
No Ethernet device is detected.
Under normal operation, if the PWR and LINE indicators are on you should be able to
use your new phone lines. The ETHERNET indicator state depends on the equipment
you have connected to your SuperLine IAD. The TST and ALM indicators can be
initiated by your service provider. For conditions other than these, refer to
Troubleshooting Your SuperLine IAD
on page 21 for indicators requiring action.
6
SuperLine IAD Rear Panel
The rear panel of your SuperLine IAD has six jacks.
98-16095a
POWER PHONE 2 PHONE 1/2 ETHERNET
BASE
PHONE
LINE
Rear Panel Jacks
This Jack Allows You To
POWER Apply power to your SuperLine IAD.
PHONE 2 Connect a phone, fax machine, or modem if you have ordered
two additional lines. This jack is not functional if you have only
one additional line through your SuperLine IAD.
PHONE 1/2 Connect a phone, fax machine, or modem if you have one or
two additional lines. This jack is also used to connect a 2-line
phone with a single 2-line phone cable if you have ordered two
additional lines.
ETHERNET Connect high-speed Ethernet data services. Ask your service
provider about the availability of high-speed Ethernet data
services.
BASE PHONE Connect your existing phone to the SuperLine IAD. This jack
provides uninterrupted phone service in the event of a power
outage.
LINE Connect your SuperLine IAD to the existing phone’s wall jack.
7
Installing Your SuperLine IAD
Before you install your SuperLine IAD, read the
Important Safety Instructions
on
page 27.
There are several ways to connect your SuperLine IAD, depending on your current
phone configuration, data needs (Internet), and future needs. You can connect any
combination of two phones, fax machines, or modems through your SuperLine IAD.
Any device connected to your SuperLine IAD must be FCC Part 68-registered for the
U.S. and Industry Canada CS-03-certified for use in Canada.
Connecting Multiple Phones, Fax Machines, or Modems to Your SuperLine
IAD
This procedure describes how to connect multiple phones, fax machines, or
modems to your SuperLine IAD (page 8).
Connecting a 2-Line Phone (with Existing Phone and One or Two Additional
Lines)
This procedure describes how to connect a 2-line phone to your SuperLine IAD if
you have ordered one or two additional lines with your SuperLine IAD (page 10).
Connecting 2-Line Phone (with Two Additional Lines)
This procedure describes how to connect a 2-line phone to your SuperLine IAD if
you have ordered two additional lines with your SuperLine IAD (page 12). You can
also connect the third line of a 3-line phone or an additional phone, fax machine, or
modem.
Connecting a Modem to Your SuperLine IAD
This procedure describes how to connect a modem through the PHONE 1/2 and
PHONE 2 jacks on your SuperLine IAD rear panel (page 14).
Optional Configuration
This procedure describes how to connect multiple phones, fax machines, or
modems in separate rooms (page 16). This configuration may not be applicable in
all homes or small offices.
High-Speed Data Service
This procedure describes how to connect your SuperLine IAD to a PC or Hub for
high-speed Internet services using the Ethernet port (page 18). This feature may
not be available in your area. Contact your local phone company for further
information.
Connecting Phone Filters to Your Existing Phones
This procedure describes how to connect a phone filter to your existing phones
(page 19).
Applying Power to the Unit
This section provides steps to apply power to your SuperLine IAD and verify its
proper operation (page 20).
8
Connecting Multiple Phones, Fax Machines, or Modems
to Your SuperLine IAD
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H Existing RJ11 phone cables.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine IAD with
up to two additional phones, fax machines, or modems in the same room.
Existing Phone Line
Plug one end of your phone cable into the LINE jack on the SuperLine IAD rear
panel.
Connect the other end of the cable into the wall jack.
Connect your existing phone to the BASE PHONE jack on the SuperLine IAD rear
panel. For optimal performance, do not use the BASE PHONE jack to connect a
modem.
NOTE:
If you lose power to your SuperLine IAD, the phone connected to the BASE
PHONE jack, and other phones connected to the same line as the SuperLine IAD,
will still be operational.
Second Phone, Fax Machine, or Modem:
Connect a second phone, fax machine, or modem to the PHONE 1/2 jack on the
SuperLine IAD rear panel using the supplied cable.
NOTE:
If you use the PHONE 2 jack, do not use a 4-wire phone cable to connect phones,
fax machines, or modems to the PHONE 1/2 jack. A 4-wire phone cable connected
to the PHONE 1/2 jack may cause interference on phones, fax machines, or
modems connected to the PHONE 2 jack. Use the supplied cable.
Third Phone, Fax Machine, or Modem:
Connect a third phone, fax machine, or modem to the PHONE 2 jack on the
SuperLine IAD rear panel using one of your existing cables.
9
To complete your SuperLine IAD installation, refer to
Connecting Phone Filters to Your
Existing Phones
on page 19, and
Applying Power to the Unit
on page 20.
Phone,
Fax Machine,
or Modem
Phone 2
Phone 1/2
Base
Phone
Line
Wall
Jack
TST
DSL
ETHERNET
ALMPWR
TST
DSL
ETHERNET
ALMPWR
Existing
Phone
99-16035a-02
Phone,
Fax Machine,
or Modem
Supplied
Cable
Connecting Multiple Phones, Fax Machines, or Modems to Your
SuperLine IAD
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
10
Connecting a 2-Line Phone (with Existing Phone
and One or Two Additional Lines)
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H Existing RJ11 phone cables.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine IAD to a
single phone with two lines. This configuration can be used if you have one or two
additional phone lines through your SuperLine IAD.
Line 1:
Plug one end of your phone cable into the LINE jack on the SuperLine IAD rear
panel.
Insert the other end of the phone cable into the wall jack.
Connect Line 1 of your 2-line phone to the BASE PHONE jack on the SuperLine
IAD rear panel.
Line 2:
Connect Line 2 of the 2-line phone to the PHONE 1/2 jack on the rear of the
SuperLine IAD using the supplied cable.
NOTE:
If you use the PHONE 2 jack, do not use a 4-wire phone cable to connect phones,
fax machines, or modems to the PHONE 1/2 jack. A 4-wire phone cable connected
to the PHONE 1/2 jack may cause interference on phones, fax machines, or
modems connected to the PHONE 2 jack. Use the supplied cable.
Second Phone, Fax Machine, Modem, or Line 3:
If you have ordered two additional lines, you can connect a second phone, fax
machine, modem, or Line 3 of a 3-line phone to the PHONE 2 jack on the
SuperLine IAD rear panel using one of your existing cables.
To complete your SuperLine IAD installation, refer to
Connecting Phone Filters to Your
Existing Phones
on page 19, and
Applying Power to the Unit
on page 20.
11
99-16100-02
Phone 1/2
Base Phone
Line 2
Line 1
2-Line
Phone
Wall
Jack
Phone 2
Line
TST
DSL
ETHERNET
ALMPWR
Phone,
Fax Machine,
or Modem
Supplied
Cable
Connecting a 2-Line Phone (with One or Two Additional Lines)
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
12
Connecting a 2-Line Phone (with Two Additional Lines)
Hardware Required (Not Supplied)
H A 2-line phone cable (RJ14C) to connect Lines 1 and 2 of your 2-line phone to your
SuperLine IAD. Refer to
Technical Information
on page 23 for RJ14C phone cable
pin configuration.
H Existing RJ11 phone cables to connect the SuperLine IAD to the wall jack and your
existing phone to the SuperLine IAD.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine IAD to a
single phone with two lines.
NOTE:
Use this configuration only if you have two additional phone lines through your
SuperLine IAD.
Lines 1 and 2:
Plug one end of your phone cable into the LINE jack on the SuperLine IAD rear
panel.
Insert the other end of the cable into the wall jack.
Connect your 2-line phone using the 2-line RJ14C phone cable to the PHONE 1/2
jack on the SuperLine IAD rear panel. The 2-line phone cable connects both lines
through the PHONE 1/2 jack.
NOTE:
The PHONE 2 jack cannot be used to connect a fax machine or modem in this
configuration.
Existing Phone, Fax Machine, or Modem:
Connect your existing phone, fax machine, or modem to the BASE PHONE jack on
the SuperLine IAD rear panel.
NOTE:
If you lose power to your SuperLine IAD, the device connected to the BASE
PHONE jack will still be operational.
To complete your SuperLine IAD installation, refer to
Connecting Phone Filters to Your
Existing Phones
on page 19, and
Applying Power to the Unit
on page 20.
13
TST
DSL
ETHERNET
ALMPWR
99-16036a-02
Phone 1/2
Base Phone
RJ14
Phone
Cable
2-Line
Phone
Wall
Jack
Line
Phone,
Fax Machine,
or Modem
Phone 2
(not used in
this configuration)
Connecting a 2-Line Phone (with Two Additional Lines)
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
14
Connecting a Modem to Your SuperLine IAD
Hardware Required (Supplied)
H A 6-foot RJ11 phone cable.
" Procedure
Use the following procedure and supporting figure to connect a modem to your
SuperLine IAD.
NOTE:
For optimal performance, do not use the BASE PHONE jack to connect a modem.
Modem Connection:
Connect the output of your modem to the PHONE 1/2 or PHONE 2 jack on the
SuperLine IAD rear panel using the supplied cable.
— Use only the PHONE 1/2 jack if you have one additional phone line.
— Use either the PHONE 1/2 or PHONE 2 jack if you have two additional phone
lines. You can connect an additional phone, fax machine, or another modem to
the unused jack (PHONE 1/2 or PHONE 2).
To complete your SuperLine IAD installation, refer to
Connecting Phone Filters to Your
Existing Phones
on page 19, and
Applying Power to the Unit
on page 20.
15
99-16066-02
Phone 1/2
Base Phone
Wall
Jack
Phone 2
Line
Phone,
Fax Machine,
or Modem
TST
DSL
ETHERNET
ALMPWR
Fax/Data
Modem
or
TST
DSL
ETHERNET
ALMPWR
Connecting a Modem
16
Optional Configuration
If your home or office phone jacks are wired internally with 4 wires (Pins 2, 3, 4, and 5),
you may be able to connect phones in other rooms to your SuperLine IAD by using
optional hardware purchased from your local electronics or phone store. If you are
unsure if your home or office is wired with 4 wires, contact an electrician or your service
provider.
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H “T” type connectors. Refer to
“T” Type Connector
on page 25 for “T” type connector
specifications.
H RJ11 phone cables to connect the SuperLine IAD to the “T” type connector and
your existing phone to the SuperLine IAD.
" Procedure
Use the following procedure and supporting figure to install your SuperLine IAD with
multiple phones, fax machines, or modems connected in other rooms.
In the Same Room as your SuperLine IAD:
Plug a “T” type connector into the wall jack of the room where the SuperLine IAD is
located.
Plug one end of your phone cable into the LINE jack on the SuperLine IAD rear
panel.
Plug the other end of your phone cable into Line 1 of the “T” type connector.
Plug the supplied phone cable into Line 2 of the “T” type connector.
Plug the other end of the supplied phone cable into the PHONE 1/2 jack on the
SuperLine IAD rear panel.
NOTE:
Do not use a 4-wire phone cable to connect phones, fax machines, or modems to
the PHONE 1/2 jack. A 4-wire phone cable connected to the PHONE 1/2 jack may
cause interference on devices connected to the PHONE 2 jack.
In Another Room:
Plug a second “T” type connector into the wall jack of another room.
Connect the additional phone to Line 2 of the “T” type connector. You can connect
a phone to your existing phone line using Line 1 of the “T” type connector and a
phone filter as shown.
Repeat Steps 6 and 7 for any additional rooms you want to connect.
Third Phone, Fax or Modem:
If applicable, connect a third phone, fax machine, or modem into the PHONE 2
jack on the SuperLine IAD rear panel using one of your existing cables.
17
To complete your SuperLine IAD installation, refer to
Connecting Phone Filters to Your
Existing Phones
on page 19, and
Applying Power to the Unit
on page 20.
Wall
Jack
99-16037a-02
Phone 1/2
Base Phone
Phone 2
Line 2
4-Wire
Internal Wiring
*
Line 2
Line 1
Line
Phone
Filter
Existing
Phone
Line
Line 1
Line 2
Phone
Filter
Existing
Phone
Line
Line 1
Additional Line
Additional Line
Additional
Line
PHO
NE
LIN
E
PHO
NE
L
IN
E
Supplied
Cable
* Not all homes or offices are wired internally with 4 wires. If you are unsure of your
internal home or office wiring, contact your service provider or an electrician.
Optional Configuration
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
18
High-Speed Data Service (Not Available in All Areas)
The SuperLine IAD allows you to connect to a PC network interface card (NIC) or Hub
for high-speed Internet access. Contact your service provider to determine if these
services are available in your area.
Hardware Required (Not Supplied)
H Straight-through or crossover Ethernet interface cable. Refer to
Ethernet Cable
on
page 24 for Ethernet cable pin configurations.
" Procedure
Use the following procedure to connect your SuperLine IAD to a PC or Hub.
Ethernet Connection:
Plug one end of the cable into the ETHERNET jack on the SuperLine IAD rear
panel.
— Use an 8-pin Ethernet crossover cable to connect your PC.
— Use an 8-pin straight-through cable to connect to a Hub.
Plug the other end into your PC network interface card (NIC) or Hub.
99-16038a-02
or
Wall
Jack
Ethernet
PC
Hub
TST
LINE
ALMPWR
ETHERNET
Apply power to the unit (refer to
Applying Power to the Unit
on page 20). Verify the
ETHERNET indicator on the SuperLine IAD front panel is lit.
NOTE:
Your PC must be on in order for the ETHERNET indicator to light.
19
Connecting Phone Filters to Your Existing Phones
Procedure
After you have installed your SuperLine IAD, each phone in your home or office that is
connected to the same line as the SuperLine IAD must be connected through a phone
filter to minimize background noise during telephone conversations. Use the following
procedure to install phone filters on your existing phones.
NOTE:
You may need to purchase additional phone filters from your service provider.
Disconnect the phone cord of your existing phone from the wall jack.
Plug the phone cord into the PHONE jack on the phone filter.
Plug the phone filter into the wall jack.
Repeat Steps 1–3 for each phone in your home or office that is not connected through
your SuperLine IAD.
LINE
PHONE
99-16210-01
g
e
p
ru
fte
S
ic
h
e
rh
e
it
R
LR92997
TM
TUY
PRODUCT SERVICE
Phone Filter
P/N 0802-3392-00
Made in China / Fabriquè China
Bel Fuse Inc. 1198
ACCESSARY
L.T.E. EQUIPMENT
E100296
20
Applying Power to the Unit
Procedure
After you have installed your SuperLine IAD, use the following procedure to apply
power to the SuperLine IAD.
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel.
Plug the transformer into an ac power outlet.
99-16048a-02
Power
Phone,
Fax Machine,
or Modem
TST
DSL
ETHERNET
ALMPWR
After power is applied, the SuperLine IAD performs a power-on self-test. During the
power-on self-test, all front panel indicators light for one second and then turn off. Only
the PWR, LINE, and ETHERNET (if applicable) indicators remain lit. If any other
indicators remain lit, refer to
Troubleshooting Your SuperLine IAD
on page 21. Refer to
Front Panel Indicators
on page 5 for more information on SuperLine IAD front panel
indicators.
Congratulations. Your SuperLine IAD installation is now complete.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Paradyne 6512-A2 Installation Instructions Manual

Marca
Paradyne
Modello
6512-A2
Tipo
Installation Instructions Manual
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti