Paradyne 6512-A2 Installation Instructions Manual

Marca
Paradyne
Modello
6512-A2
Tipo
Installation Instructions Manual
TM
1
SuperLine Integrated Access Device
Model 6512-A2
Installation Instructions
Document Number 6512-A2-GN10-40
June 1999
TST
LINE
ALMPWR
ETHERNET
TM
TM
98-16014a-02
BASE
PHONE
Rear
View
Front
View
SuperLine
TM
IAD
Contents
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Indicator Lights 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Information 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Notes on SuperLine IAD Operation 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Introduction: What Your SuperLine IAD Does
Your SuperLine Integrated Access Device (IAD) is a line adapter that allows you to
connect multiple phones, fax machines, or modems using your existing phone wiring.
99-16257
TST
LINE
ALMPWR
ETHERNET
TM
TM
Existing
Phone Line
Existing (BASE) Phone
Additional Line (PHONE 1/2)
Additional Line (PHONE 2)
Ethernet Data
Your service provider enables SuperLine service and assigns phone numbers to the
additional phone lines.
The SuperLine IAD:
H Transforms your existing single phone line into multiple phone lines to support up
to two additional phones, fax machines, or modems simultaneously.
H Provides high-speed Internet access through an Ethernet connection. (Available in
some areas. Ask your service provider about availability of this service.)
H Operates with Touch Tonet phones. The PHONE 1/2 and PHONE 2 jacks do not
support pulse dial phones. (Your existing phone, plugged into the BASE PHONE
jack, can be a pulse dial phone.)
The following figure depicts a typical home or small office configuration with several
existing phones and two additional lines. Phone filters are connected to your existing
phones to reduce interference from the new line or lines.
99-16018a-02
Wall
Jack
SuperLine
IAD
Wall
Jack
Phone
Filter
Phone
Filter
Existing
Phone
Line
Existing
Phone
Line
Existing
Phone
Line
Additional
Line
Additional
Line
3
Package Checklist
Verify that your package contains the following hardware. If any hardware is missing or
you need to order additional hardware, contact your service provider. Refer to
Technical
Information
on page 28 for further information.
SuperLine
IAD
6' RJ11
Phone
Cable
AC Power Transformer
(327-0118-0031)
99-16015a-02
Phone Filter
(6035-A1-002)
TST
LINE
ALMPWR
ETHERNET
TM
TM
LINE
PHONE
geprufte
Sicherheit
R
LR92997
TM
TUY
PRODUCT SERVICE
Phone Filter
P/N 0802-3392-00
Made in China / Fabriquè China
Bel Fuse Inc. 1198
ACCESSARY
L.T.E. EQUIPMENT
E100296
99-16406
LINE
PHONE
99-16410
g
e
p
r
u
f
t
e
S
i
c
h
e
r
h
e
i
t
R
LR92997
T
M
TUY
PRODUCT SERVICE
Phone Filter
P
/N
0
8
0
2
-3
3
9
2
-0
0
M
a
d
e
in
C
h
in
a
/ F
a
b
r
iq
u
è
C
h
in
a
B
e
l F
u
s
e
I
n
c
. 1
1
9
8
A
C
C
E
S
S
A
R
Y
L
.T
.E
.
E
Q
U
IP
M
E
N
T
E
1
0
0
2
9
6
TM
TST
LINE
A
LMPW
R
ETH
ER
N
ET
T
M
T
M
B
A
S
E
P
H
O
N
E
TM
Quick Installation
Installation
Instructions
4
5
Installation
Before you install your SuperLine IAD, read the
Additional Notes on SuperLine IAD
Operation
on page 32, and the
Important Safety Instructions
on page 33.
Choose the procedure that sounds most like what you want to do:
H Add a Second Phone Line Page 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to add a new line for a phone.
H Add a Second Line for a Modem Page 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to add a new line for a modem.
H Work at Home Page 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to add new lines for a modem and an additional
phone.
H Home Office Page 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to connect an additional phone, fax machine, and
Ethernet-ready PC to your SuperLine IAD.
H Connect Phone Filters to Your Existing Phones Page 14. . . . . . . . . . . . . . . . . .
This procedure describes how to connect a phone filter to your existing phones.
H Connect a 2-Line Phone to the Existing
and Additional Phone Line Page 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to connect a 2-line, 2-cord phone to your SuperLine
IAD.
H Connect a 2-Line Phone to Two Additional Phone Lines Page 18. . . . . . . . . .
This procedure describes how to connect a 2-line, 1-cord phone to your SuperLine
IAD if you have ordered two additional lines.
H Use an Additional Phone Line in Other Rooms Page 20. . . . . . . . . . . . . . . . . . .
This procedure describes how to connect multiple phones, fax machines, or
modems in separate rooms. This configuration may not be applicable in all homes
or small offices.
H Connect to High-Speed Data Service Page 22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
This procedure describes how to connect your SuperLine IAD to a PC or hub for
high-speed Internet services using the Ethernet port.
6
Add a Second Phone Line
Use the following procedure and supporting figure to add a new phone line.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if they are not provided
with other equipment you have bought.
H Existing phone cables.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
Plug the other end of the cable into the wall jack.
Add a Second Phone Line:
Connect a phone to the PHONE 1/2 jack on the SuperLine IAD rear panel.
Connect the Existing Phone Line:
If you wish to have your existing phone line available in this location, connect your
existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.
Connect the ac power transformer:
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
7
Additional
Phone
Phone 1/2
Base
Phone
Line
Wall
Jack
Existing
Phone
99-16430
Power
Adding a Second Line for a Phone
8
Add a Second Line for a Modem
Use the following procedure and supporting figure to connect a modem to your
SuperLine IAD.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if they are not provided
with other equipment you have bought.
H Existing phone cables.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
Plug the other end of the cable into the wall jack.
Connect the Modem:
Connect the output of your modem to the PHONE 1/2 jack on the SuperLine IAD
rear panel.
Connect the Existing Phone Line:
If you wish to have your existing phone line available in this location, connect your
existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.
Connect the AC Power Transformer:
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
9
99-16066-03
Phone 1/2
Base Phone
Wall
Jack
Line
Existing
Phone
Fax/Data
Modem
Power
Adding a Second Line for a Modem
10
Work At Home: Add New Lines
for a Modem and an Additional Phone
Use the following procedure and supporting figure to connect a modem and an extra
phone to your SuperLine IAD. You must have ordered two additional lines.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if they are not provided
with other equipment you have bought.
H Existing phone cables.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
· Plug the other end of the cable into the wall jack.
Connect the Modem:
¸ Connect the output of your modem to the PHONE 1/2 jack on the SuperLine IAD
rear panel.
Connect the Additional Phone:
¹ Connect a phone to the PHONE 2 jack on the SuperLine IAD rear panel.
Connect the Existing Phone Line:
º If you wish to have your existing phone line available in this location, connect your
existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.
Connect the AC Power Transformer:
» Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
11
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
99-16434
Phone 1/2
Base Phone
Wall
Jack
Line
Existing
Phone
Fax/Data
Modem
Phone 2
Additional
Phone
Power
Connecting a Modem and an Additional Phone
12
Home Office: Add High-Speed Data Service,
a Fax Machine, and an Additional Phone
Use the following procedure and supporting figure to connect an Ethernet-ready PC,
fax machine, and additional phone to your SuperLine IAD in the same room. You must
have ordered two additional lines and Ethernet data service.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if they are not provided
with other equipment you have bought.
H 8-pin Ethernet crossover cable.
H Existing phone cables.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
· Plug the other end of the cable into the wall jack.
Connect to High-Speed Data Service:
¸ Connect the network interface card of your PC to the ETHERNET jack on the
SuperLine IAD rear panel with a crossover cable. (If you are connecting to a hub,
you need a straight-through Ethernet cable. See
High-Speed Data Service
on
page 22.)
Connect the Fax Machine:
¹ Connect a fax machine to the PHONE 1/2 jack on the SuperLine IAD rear panel.
Connect the Additional Phone:
º Connect a phone to the PHONE 2 jack on the SuperLine IAD rear panel.
Connect the Existing Phone Line:
» If you wish to have your existing phone line available in this location, connect your
existing phone to the BASE PHONE jack on the SuperLine IAD rear panel.
13
Connect the AC Power Transformer:
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
Fax
Machine
Phone 2
Phone 1/2
Base
Phone
Line
99-16433
Ethernet
Existing
Phone
PC with
Network
Interface
Card
Additional
Phone
Wall
Jack
Power
Adding High-Speed Data Service, a Fax Machine,
and an Additional Phone
14
Connect Phone Filters to Your Existing Phones
After you have installed your SuperLine IAD, each phone elsewhere in your home or
office that is connected to the same line as the SuperLine IAD must be connected
through a phone filter to minimize background noise from the additional lines.
Hardware Required (Not Supplied)
You may need to obtain additional phone filters from your service provider. One filter is
supplied with your SuperLine IAD.
" Procedure
Use the following procedure to install phone filters on your existing phones.
Disconnect the phone cord of your existing phone from the wall jack.
Plug the phone cord into the PHONE jack on the phone filter.
Plug the phone filter into the wall jack.
Repeat Steps 1–3 for each phone in your home or office that is not directly connected
to your SuperLine IAD.
15
LINE
PHONE
99-16210-01
g
e
p
ru
fte
S
ic
h
e
rh
e
it
R
LR92997
TM
TUY
PRODUCT SERVICE
Phone Filter
P/N 0802-3392-00
Made in China / Fabriquè China
Bel Fuse Inc. 1198
ACCESSARY
L.T.E. EQUIPMENT
E100296
Installing a Phone Filter
16
Connect a 2-Line Phone to the Existing
and Additional Phone Line
Use the following procedure and supporting figure to connect your SuperLine IAD to a
single phone with two lines. This configuration can be used if you have one or two
additional phone lines through your SuperLine IAD.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if they are not provided
with other equipment you have bought.
H Existing phone cables.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
Plug the other end of the cable into the wall jack.
Connect Line 1:
Connect Line 1 of your 2-line phone to the BASE PHONE jack on the SuperLine
IAD rear panel.
Connect Line 2:
Connect Line 2 of the 2-line phone to the PHONE 1/2 jack on the rear of the
SuperLine IAD.
Connect the AC Power Transformer:
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
17
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
99-16100-03
Phone 1/2
Base Phone
Line 2
Line 1
2-Line
Phone
Wall
Jack
Line
Power
Connecting a 2-Line Phone (with One or Two Additional Lines)
18
Connect a 2-Line Phone to Two Additional Phone Lines
Use the following procedure and supporting figure to connect your SuperLine IAD to a
single phone with two lines. Use this configuration only if you have two additional phone
lines through your SuperLine IAD.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables Required (Not Supplied)
Obtain the following from your local electronics or phone store if it is not provided with
other equipment you have bought.
H A 2-line phone cable (RJ14C) to connect Lines 1 and 2 of your 2-line phone to your
SuperLine IAD. Refer to
Technical Information
on page 23 for more information.
" Procedure
Connect the SuperLine IAD:
Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
Plug the other end of the cable into the wall jack.
Connect Lines 1 and 2:
Connect your 2-line phone using your 2-line RJ14C phone cable to the PHONE 1/2
jack on the SuperLine IAD rear panel. The 2-line phone cable connects both lines
through the PHONE 1/2 jack.
Connect the AC Power Transformer:
Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
Complete the Installation:
Attach phone filters to all your other existing phones. Refer to
Connect Phone
Filters to Your Existing Phones
on page 14.
Your SuperLine IAD installation is now complete.
19
99-16036a-03
Phone 1/2
RJ14
Phone
Cable
2-Line
Phone
Wall
Jack
Line
Phone 2
(not used in
this configuration)
Connecting a 2-Line Phone to Two Additional Lines
20
Use an Additional Phone Line in Other Rooms
If your home or office phone jacks are wired internally with 4 wires, you may be able to
connect phones in other rooms to your SuperLine IAD by using optional hardware
purchased from your local electronics or phone store. If you are unsure if your home or
office is wired with 4 wires, contact an electrician or your service provider.
Cables Required (Supplied)
H 6-foot phone cable (RJ11).
Cables and Hardware Required (Not Supplied)
You may need to obtain additional phone filters from your service provider. One filter is
supplied with your SuperLine IAD. Obtain the following from your local electronics or
phone store if they are not provided with other equipment you have bought.
H “T” type connectors. Refer to
“T” Type Connector
on page 30 for “T” type connector
specifications.
H RJ11 phone cables to connect the SuperLine IAD to the “T” type connector and
your existing phone to the SuperLine IAD.
" Procedure
Use the following procedure and supporting figure to install your SuperLine IAD with
multiple phones, fax machines, or modems connected in other rooms.
Connect the SuperLine IAD:
Plug a “T” type connector into the wall jack of the room where the SuperLine IAD is
located.
· Plug one end of the supplied phone cable into the LINE jack on the SuperLine IAD
rear panel.
¸ Plug the other end of the cable into Line 1 of the “T” type connector.
¹ Plug a phone cable into Line 2 of the “T” type connector.
º Plug the other end of the cable into the PHONE 1/2 jack on the SuperLine IAD rear
panel.
» If applicable, connect an additional phone, fax machine, or modem into the
PHONE 2 jack on the SuperLine IAD rear panel using one of your existing cables.
Connect a Phone, Fax Machine, or Modem In Another Room:
¼ Plug a second “T” type connector into the wall jack of another room.
½ Connect the additional phone, fax machine, or modem to Line 2 of the “T” type
connector. You can connect a phone to your existing phone line using Line 1 of the
“T” type connector and a phone filter as shown.
Repeat Steps 7 and 8 for any additional rooms you want to connect.
Connect the AC Power Transformer:
¾ Insert the power cord’s cylindrical plug into the jack labeled POWER on the
SuperLine IAD rear panel. Plug the transformer into an ac power outlet.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Paradyne 6512-A2 Installation Instructions Manual

Marca
Paradyne
Modello
6512-A2
Tipo
Installation Instructions Manual
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti