Paradyne 6512 Installation Instructions Manual

Marca
Paradyne
Modello
6512
Tipo
Installation Instructions Manual
TST
LINE
ALMPWR
ETHERNET
TM
TM
98-16014a-01
TM
1
SuperLine Adapter
Installation Instructions
Document Number 6512-A2-GN10-20
January 1999
SuperLineAdapter
Contents:
Important Safety Instructions
What Your SuperLine Adapter Does
Package Checklist
Optional Hardware (Not Supplied)
Front Panel Indicators
SuperLine Adapter Rear Panel
Installing Your SuperLine Adapter
Troubleshooting Your Adapter
Technical Information
Technical Specifications
Technical Support
2
!
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or
included in the manual.
2. Slots and openings in the housing are provided for ventilation. To ensure reliable
operation of the product and to protect it from overheating, these slots and
openings must not be blocked or covered.
3. Do not allow anything to rest on the power cord and do not locate the product
where people will walk on the power cord.
4. Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous high voltage points or other risks. Refer all servicing
to qualified service personnel.
5. General purpose cables are used with this product for connection to the network.
Special cables, which may be required by the regulatory inspection authority for
the installation site, are the responsibility of the customer.
6. In addition, since the equipment is to be used with telecommunications circuits,
take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
— Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the leak.
Declaration of Conformity
This Declaration of Conformity is made by Paradyne pursuant to Parts 2 and 15 of the
Federal Communications Commission’s Rules. This compliance information statement
pertains to the following products:
Trade Name: SuperLine Adapter
Model Number: 6512
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
The name and address of the responsible party is given below:
Paradyne Corporation
8345 126th Ave. N.
P.O. Box 2826
Largo, FL 33779-2826
The authority to operate this equipment is conditioned by the requirement that no
modifications will be made to the equipment unless the changes or modifications are
expressly approved by Paradyne Corporation.
3
Canada
!
WARNING:
To Users of Digital Apparatus in Canada:
This Class B digital apparatus meets all requirements of the Canadian
interference-causing equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
règlement sur le matérial brouilleur du Canada.
Notice to Users of the Canadian Telephone Network
The Industry Canada label identifies certified equipment. This certification means that
the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical
Requirements document(s). The Department does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer should
be aware that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by
the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request
to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION:
Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
the devices does not exceed 5.
If your equipment is in need of repair, refer to
Technical Support
on page 28.
4
What Your SuperLine Adapter Does
Your SuperLine Adapter allows you to connect multiple phones, fax machines, or
modems using your existing telephone wiring.
99-16257
TST
LINE
ALMPWR
ETHERNET
TM
TM
Existing
Phone Line
Existing (BASE) Phone
Superline 1 (PHONE 1/2)
Superline 2 (PHONE 2)
Ethernet Data
The SuperLine technology:
Transforms your existing single phone line into multiple phone lines (superlines) to
support up to two additional phones, fax machines, or modems simultaneously.
Operates over your existing copper wire with your existing telephone jacks.
Allows True56K V.90 modem connections supporting maximum 56K modem
speeds on your superlines.
Provides high-speed Internet access through an Ethernet connection. (Available in
some areas. Ask your local telephone company about availability of this service.)
Only operates with Touch Tone phones. The PHONE 1/2 and PHONE 2 jacks do
not support pulse dial phones. (Your existing phone, plugged into the BASE
PHONE jack, can be a pulse dial phone.)
NOTE:
Your local telephone company must enable these services and assign phone
numbers to the additional phone lines before your SuperLine Adapter will work.
Your SuperLine Adapter connects to your existing phone line to provide up to two
additional phone lines (superlines). These superlines support any combination of up to
two phones, fax machines, or modems. Your SuperLine Adapter also allows True56K
modem speeds with an International Telecommunications Union (ITU) V.90 standard
modem. The following figure depicts a typical home or small office configuration with
several existing phones and two superlines. Phone filters are connected to your
existing phones to reduce the amount of interference generated during phone
conversations.
5
99-16018a-02
Wall
Jack
SuperLine
Adapter
Wall
Jack
Phone
Filter
Phone
Filter
Existing
Phone
Line
Existing
Phone
Line
Existing
Phone
Line
Superline 2
Superline 1
P
H
O
N
E
LINE
P
H
O
N
E
LINE
Package Checklist
Verify that your package contains the following hardware. If any hardware is missing or
you need to order additional hardware, contact you local telephone company. Refer to
Technical Information
on page 25 for further information.
SuperLine
Adapter
6' RJ11
Phone Cable
AC Power Transformer
(037-0118-0031)
99-16015a-02
Phone Filter
(6035-A1-002)
TST
LINE
ALMPWR
ETHERNET
TM
TM
LINE
PHONE
geprufte
Sicherheit
R
LR92997
TM
TUY
PRODUCT SERVICE
Phone Filter
P/N 0802-3392-00
Made in China / Fabriquè China
Bel Fuse Inc. 1198
ACCESSARY
L.T.E. EQUIPMENT
E100296
98-16067a
Pin #1
Pin #6
98-16051a
6
Optional Hardware (Not Supplied)
The following hardware may be required depending on which configuration you choose
to install. You can purchase these items from your local electronics or phone store.
2-Line Phone Cable (RJ14C)
If you are connecting a 2-line phone, you may
require a 2-line phone cable (24 AWG, RJ14C)
as defined in
Connecting a 2-Line Phone (with
Two Superlines)
on page 14. Refer to
Technical
Information
on page 25 for the 2-line phone
cable pin configuration.
“T” Type Connector
If your home or office phone jacks are wired
internally with 4 wires, you may be able to connect
phones in other rooms to your SuperLine Adapter
using a “T” type connector as defined in
Optional
Configuration
on page 18. Refer to
“T” Type
Connector
on page 27 for the “T” type
connector pin configuration.
7
Front Panel Indicators
99-16016a-01
Power – Green
Alarm – Red
Test – Yellow
Line – Green
Ethernet – Green
TST
LINE
ALMPWR
ETHERNET
TM
TM
All of the adapter’s indicators turn ON and OFF during the power-on self-test. After a
successful power-on self-test, the adapter’s indicators should appear as indicated in
BOLD in the Condition column of the following table:
Indicator Condition Status
PWR ON Power is applied to the adapter.
ALM OFF
ON
No active alarms.
An alarm condition exists which may require further
attention. Refer to
Troubleshooting Your Adapter
on
page 22.
TST OFF
ON
No active tests.
The TST indicator is ON during the power-on self-test and
during testing or upgrades initiated by your network
service provider. Superline service is not available when
the TST indicator is ON. Your existing (BASE) phone still
works.
LINE ON
OFF
Your adapter is connected to your local phone company
and is ready to use.
The link has not been established.
ETHERNET ON
OFF
The Ethernet connection to your PC or Ethernet Hub is
made and your PC is ON.
No Ethernet device is detected.
Under normal operation, if the PWR and LINE indicators are on you should be able to
access the superline service to which you have subscribed. The ETHERNET indicator
state depends on the equipment you have connected to your adapter. The TST and
ALM indicators can be initiated by your Network Service Provider. For conditions other
than these, refer to
Troubleshooting Your Adapter
on page 22 for indicators requiring
action.
8
SuperLine Adapter Rear Panel
The rear panel of your adapter has five jacks which allow you to:
Connect your existing phone
Connect up to two additional phones, fax machines, or modems
Connect a PC or Hub for high-speed Ethernet data services
Connect the supplied AC power supply
98-16095a
POWER PHONE 2 PHONE 1/2 ETHERNET
BASE
PHONE
LINE
Rear Panel Jacks
This Jack Allows You To
POWER Apply power to your SuperLine Adapter.
PHONE 2
(superline 2)
Connect a phone, fax machine, or modem if you have
purchased two superlines. This jack is not functional if you
have only one superline through your SuperLine Adapter.
PHONE 1/2
(superline 1/2)
Connect a phone, fax machine, or modem if you have one or
two superlines. This jack is also used to connect a 2-line phone
with a single 2-line phone cable if you have purchased two
superlines.
ETHERNET Connect high-speed Ethernet data services. Ask your local
phone company about the availability of high-speed Ethernet
data services.
BASE PHONE Connect your existing phone to the SuperLine Adapter. This
jack provides uninterrupted phone service in the event of a
power outage.
LINE Connect your SuperLine Adapter to the existing phone’s wall
jack.
9
Installing Your SuperLine Adapter
There are several ways to connect your SuperLine Adapter, depending on your current
phone configuration, data needs (Internet), and future needs. You can connect any
combination of two phones, fax machines, or modems through your adapter. Any
device connected to your adapter must be FCC Part 68-registered for the U.S. and
Industry Canada CS-03-certified for use in Canada.
Connecting Multiple Phones, Fax Machines, or Modems to Your Adapter
This procedure describes how to connect multiple phones, fax machines, or
modems to your SuperLine Adapter (page 10).
Connecting a 2-Line Phone (with One or Two Superlines)
This procedure describes how to connect a 2-line phone to your SuperLine
Adapter if you have purchased one or two superlines with your adapter (page 12).
Connecting 2-Line Phone (with Two Superlines)
This procedure describes how to connect a 2-line phone to your SuperLine
Adapter if you have purchased two superlines with your adapter (page 14). You
can also connect the third line of a 3-line phone or an additional phone, fax
machine, or modem.
Connecting a Modem to Your Adapter
This procedure describes how to connect a modem through the superline
PHONE 1/2 and PHONE 2 jacks on your adapter rear panel (page 16).
Optional Configuration
This procedure describes how to connect multiple phones, fax machines, or
modems in separate rooms (page 18). This configuration may not be applicable in
all homes or small offices.
High-Speed Data Service
This procedure describes how to connect your SuperLine Adapter to a PC or Hub
for high-speed Internet services (page 20). This feature may not be available in
your area. Contact your local phone company for further information.
Connecting Phone Filters to Your Existing Phones
This procedure describes how to connect a phone filter to your existing phones
(page 21).
Applying Power to the Unit
This section provides steps to apply power to your adapter and verify its proper
operation (page 22).
10
Connecting Multiple Phones, Fax Machines, or Modems
to Your Adapter
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H An RJ11 phone cable for each device you attach to the SuperLine Adapter.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine Adapter
with up to two additional phones, fax machines, or modems in the same room.
Existing Phone Line
Plug one end of the 6-foot phone cable into the LINE jack on the adapter rear
panel.
Connect the other end of the cable into the wall jack.
Connect your existing phone into the BASE PHONE jack on the adapter rear
panel.
NOTE:
If you lose power to your SuperLine Adapter, the phone connected to the BASE
PHONE jack, and other phones connected to the same line as the SuperLine
Adapter, will still be operational.
Second Phone, Fax Machine, or Modem:
Connect a second phone, fax machine, or modem into the PHONE 1/2 jack on the
adapter rear panel.
NOTE:
If you use the PHONE 2 jack, do not use a 4-wire phone cable to connect phones,
fax machines, or modems to the PHONE 1/2 jack. A 4-wire phone cable connected
to the PHONE 1/2 jack may cause interference on phones, fax machines, or
modems connected to the PHONE 2 jack.
Third Phone, Fax Machine, or Modem:
Connect a third phone, fax machine, or modem into the PHONE 2 jack on the
adapter rear panel.
11
To complete your SuperLine Adapter installation, refer to
Connecting Phone Filters to
Your Existing Phones
on page 21, and
Applying Power to the Unit
on page 22.
Phone,
Fax Machine,
or Modem
Phone 2
Phone 1/2
Base
Phone
Line
Wall
Jack
TST
DSL
ETHERNET
ALMPWR
TST
DSL
ETHERNET
ALMPWR
Existing
Phone
99-16035a-02
Connecting Multiple Phones, Fax Machines, or Modems to Your Adapter
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
12
Connecting a 2-Line Phone (with Existing Phone
and One or Two Superlines)
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H Two additional RJ11 phone cables to connect Lines 1 and 2 of your 2-line phone to
your adapter.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine Adapter
to a single phone with two lines. This configuration can be used if you have one or two
additional phone lines through your SuperLine Adapter.
Line 1:
Plug one end of the 6-foot phone cable into the LINE jack on the adapter rear
panel.
Insert the other end of the phone cable into the wall jack.
Connect Line 1 of your 2-line phone into the BASE PHONE jack on the adapter
rear panel.
Line 2:
Connect Line 2 of the 2-line phone into the PHONE 1/2 jack on the rear of the
adapter.
NOTE:
If you use the PHONE 2 jack, do not use a 4-wire phone cable to connect phones,
fax machines, or modems to the PHONE 1/2 jack. A 4-wire phone cable connected
to the PHONE 1/2 jack may cause interference on phones, fax machines, or
modems connected to the PHONE 2 jack.
Second Phone, Fax Machine, Modem, or Line 3:
If you have purchased two superlines, you can connect a second phone, fax
machine, modem, or Line 3 of a 3-line phone into the PHONE 2 jack on the
adapter rear panel.
To complete your SuperLine Adapter installation, refer to
Connecting Phone Filters to
Your Existing Phones
on page 21, and
Applying Power to the Unit
on page 22.
13
99-16100-02
Phone 1/2
Base Phone
Line 2
Line 1
2-Line
Phone
Wall
Jack
Phone 2
Line
Connecting a 2-Line Phone (with One or Two Superlines)
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
14
Connecting a 2-Line Phone (with Two Superlines)
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H A 2-line phone cable (RJ14C) to connect Lines 1 and 2 of your 2-line phone to your
SuperLine Adapter. Refer to
Technical Information
on page 23 for RJ14C phone
cable pin configuration.
" Procedure
Use the following procedure and supporting figure to connect your SuperLine Adapter
to a single phone with two lines.
NOTE:
Use this configuration only if you have two additional phone lines through your
SuperLine Adapter.
Lines 1 and 2:
Plug one end of the 6-foot phone cable into the LINE jack on the adapter rear
panel.
Insert the other end of the cable into the wall jack.
Connect your 2-line phone using the 2-line RJ14C phone cable to the PHONE 1/2
jack on the adapter rear panel. The 2-line phone cable connects both lines through
the PHONE 1/2 jack.
NOTE:
The PHONE 2 jack cannot be used to connect additional phones, fax machines, or
modems in this configuration.
Existing Phone, Fax Machine, or Modem:
Connect your existing phone, fax machine, or modem to the BASE PHONE jack on
the adapter rear panel.
NOTE:
If you lose power to your SuperLine Adapter, the phone connected to the BASE
PHONE jack will still be operational.
To complete your SuperLine Adapter installation, refer to
Connecting Phone Filters to
Your Existing Phones
on page 21, and
Applying Power to the Unit
on page 22.
15
TST
DSL
ETHERNET
ALMPWR
99-16036a-02
Phone 1/2
Base Phone
RJ14
Phone
Cable
2-Line
Phone
Wall
Jack
Line
Phone,
Fax Machine,
or Modem
Phone 2
(not used in
this configuration)
Connecting a 2-Line Phone (with Two Superlines)
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
16
Connecting a Modem to Your Adapter
Hardware Required (Not Supplied)
H An RJ11 phone cable to connect your modem.
" Procedure
Use the following procedure and supporting figure to connect a modem to your
SuperLine Adapter.
NOTE:
Any modem can be connected to the PHONE 1, PHONE 2 or BASE PHONE jacks
of your adapter. However, if you have an International Telecommunications Union
(ITU) V.90 standard 56 kbps modem connected to the PHONE 1/2 or PHONE 2
jacks, your SuperLine Adapter allows you to achieve True56K upload and
download speeds.
Modem Connection:
Connect the output of your modem to the PHONE 1/2 or PHONE 2 jack on the
adapter rear panel.
— Use only the PHONE 1/2 jack if you have one additional phone line added.
— Use either the PHONE 1/2 or PHONE 2 jack if you have two additional phone
lines added. You can connect an additional phone, fax machine, or another
modem to the unused jack (PHONE 1/2 or PHONE 2).
To complete your SuperLine Adapter installation, refer to
Connecting Phone Filters to
Your Existing Phones
on page 21, and
Applying Power to the Unit
on page 22.
17
99-16066-02
Phone 1/2
Base Phone
Wall
Jack
Phone 2
Line
Phone,
Fax Machine,
or Modem
TST
DSL
ETHERNET
ALMPWR
Fax/Data
Modem
or
TST
DSL
ETHERNET
ALMPWR
Connecting a Modem
18
Optional Configuration
If your home or office phone jacks are wired internally with 4 wires (Pins 2, 3, 4, and 5),
you may be able to connect phones in other rooms to your SuperLine Adapter by using
optional hardware purchased from your local electronics or phone store. If you are
unsure if your home or office is wired with 4 wires, contact an electrician or your local
phone company.
Hardware Required (Supplied)
H 6-foot RJ11 phone cable.
Hardware Required (Not Supplied)
H “T” type connectors. Refer to
Technical Information
on page 25 for “T” type
connector specifications.
H Second RJ11 phone cable.
" Procedure
Use the following procedure and supporting figure to install your SuperLine Adapter
with multiple phones, fax machines, or modems connected in other rooms.
In the Same Room as Your Adapter:
Plug a “T” type connector into the wall jack of the room where the adapter is
located.
Plug one end of the phone cable into the LINE jack on the adapter rear panel.
Plug the other end of the phone cable into Line 1 of the “T” type connector.
Plug a second phone cable (not supplied) to Line 2 of the “T” type connector.
Plug the other end of the second phone cable into the PHONE 1/2 jack on the
adapter rear panel.
NOTE:
Do not use a 4-wire phone cable to connect phones, fax machines, or modems to
the PHONE 1/2 jack. A 4-wire phone cable connected to the PHONE 1/2 jack may
cause interference on devices connected to the PHONE 2 jack.
In Another Room:
Plug a second “T” type connector into the wall jack of another room.
Connect the additional phone to Line 2 of the “T” type connector. You can connect
a phone to your existing phone line using Line 1 of the “T” type connector and a
phone filter as shown.
Repeat Steps 6 and 7 for any additional rooms you want to connect.
Third Phone, Fax or Modem:
If applicable, connect a third phone, fax machine, or modem into the PHONE 2
jack on the adapter rear panel.
To complete your SuperLine Adapter installation, refer to
Connecting Phone Filters to
Your Existing Phones
on page 21, and
Applying Power to the Unit
on page 22.
19
Wall
Jack
99-16037a-02
Phone 1/2
Base Phone
Phone 2
Line 2
4-Wire
Internal Wiring
*
Line 2
Line 1
Line
Phone
Filter
Existing
Phone
Line
Line 1
Line 2
Phone
Filter
Existing
Phone
Line
Line 1
Superline 1
Superline 1
Superline 2
PH
O
N
E
LIN
E
PHO
NE
L
IN
E
* Not all homes or offices are wired internally with 4 wires. If you are unsure of your
internal home or office wiring, contact your local phone company or an
electrician.
Optional Configuration
CAUTION:
Do not attempt to connect phone cables from the PHONE 1/2 and PHONE 2
jacks to phones located outdoors. Keep all wiring connected to the
PHONE 1/2 and PHONE 2 jacks within your home or office.
20
High-Speed Data Service (Not Available in all Areas)
The SuperLine Adapter allows you to connect to a PC network interface card (NIC) or
Hub for high-speed Internet access. Contact your local phone company to determine if
these services are available in your area.
Hardware Required (Not Supplied)
H Straight-through or crossover Ethernet interface cable. Refer to
Technical
Information
on page 25 for Ethernet cable pin configurations.
" Procedure
Use the following procedure to connect your SuperLine Adapter to a PC or Hub.
Ethernet Connection:
Plug one end of the cable into the ETHERNET jack on the adapter rear panel.
— Use an 8-pin Ethernet crossover cable to connect your PC.
— Use an 8-pin straight-through cable to connect to a Hub.
Plug the other end into your PC network interface card (NIC) or Hub.
99-16038a-02
or
Wall
Jack
Ethernet
PWR ALM TST LINE ETHERNET
PC
Hub
Apply power to the unit (refer to
Applying Power to the Unit
on page 22). Verify the
ETHERNET indicator on the adapter front panel is lit.
NOTE:
Your PC must be on in order for the ETHERNET indicator to light.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Paradyne 6512 Installation Instructions Manual

Marca
Paradyne
Modello
6512
Tipo
Installation Instructions Manual
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti