Datalogic BC-80X0 Cradle specificazione

BC-80X0 Cradle

Quick Reference Guide

Datalogic ADC, Inc.

959 Terry Street

Eugene, OR 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

mentation or the procedures described therein may be reproduced or transmitted

in any form or by any means without prior written permission of Datalogic ADC,

Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”). Owners of Data-

logic products are hereby granted a non-exclusive, revocable license to reproduce

and transmit this documentation for the purchaser's own internal business pur-

poses. Purchaser shall not remove or alter any proprietary notices, including copy-

right notices, contained in this documentation and shall ensure that all notices

appear on any reproductions of the documentation.

Should future revisions of this manual be published, you can acquire printed ver-

sions by contacting your Datalogic representative. Electronic versions may either

be downloadable from the Datalogic website (www.datalogic.com) or provided on

appropriate media. If you visit our website and would like to make comments or

suggestions about this or other Datalogic publications, please let us know via the

"Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual

that is complete and accurate, however, Datalogic reserves the right to change any

specification at any time without prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in

many countries, including the U.S.A. and the E.U. All other brand and product

names may be trademarks of their respective owners.

Patents

This product may be covered by the following patent:

US Pat. 7,948,214 B2.

Additional patents pending.

BC-80X0

1

USING THE BC-80X0 RADIO CRADLE

The BC-80X0 cradle, paired with one or more Powerscan™ M8300 readers,

builds a Cordless Reading System for the collection, decoding and transmission

of barcoded data.

It can be connected to a Host PC through an RS-232, USB, Wedge or Pen

cable and is suited for single-cradle point-to-point layouts. It can also be

connected to a C-BOX and therefore integrated into a fixed scanner application.

The BC-8060 models also allow multi-cradle layouts through an RS-485

Network. For this network connection refer to the Powerscan™ D8330/M8300

Reference Manual.

The label on the cradle contains LED indicators and a scan finder button.

When the button is pressed, the cradle transmits a “broadcast” message. All

properly configured scanners (Radio RX Timeout set to keep the radio “awake”)

that are linked to that base (through a bind or a join sequence) and within radio

range coverage will emit a beep sequence once every 2 seconds for 30

seconds. This functionality is useful to:

- verify which scanners are linked to a certain base station

- detect a scanner forgotten somewhere

The LEDs signal the BC-80X0 status, as described in the following table:

LED

STATUS

Aux

Yellow On = BC-80X0 is powered through an external power supply.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Host

Yellow On = BC-80X0 is powered by the Host.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Reader

Green On = the reader battery is completely charged.

Red On = the reader battery is charging.

Orange Blinking = reader battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

Spare*

Green On = the spare battery is completely charged.

Red On = the spare battery is charging.

Orange Blinking = spare battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

* This LED refers to the accessory SBS-8000 Spare Battery Slot when mounted to the BC-8060. Not

available for BC-8010 models.

Figure 1 – Cradle Overview

Figure 2 – LEDs

DATALOGIC

2

To set up your BC-80X0 cradle you must:

1. Physically install the cradle.

2. Make all system connections.

3. Configure the BC-80X0 cradle.

INSTALLATION

MOUNTING THE BC-80X0 CRADLE

The cradle package contains the following items:

BC-80X0

1 horizontal base

BC-80X0 Quick Reference Guide

2 wall-mounting lock hinges

BC-8000 Antenna

4 rubber feet

2 adhesive strips

1 inclined base

The cradle can be mounted for portable or fixed desktop usage, or it can be

fixed to a wall. The horizontal base allows portable and fixed desktop usage,

while the inclined base provides desktop and wall mounting guaranteeing a

comfortable handling of the Powerscan™ M8300 reader.

BC-80X0 Cradle mounted on the Horizontal Base

BC-80X0 Cradle mounted on the Inclined Base

BC-80X0

3

Desktop mounting

For desktop usage, you can mount the cradle either on the horizontal base, for

reduced overall dimensions, or on the inclined base for a more ergonomic taking

out and insertion of the reader onto the cradle.

Horizontal base

Top View Bottom View

Inclined base

Top View Bottom View

Mounting

Tabs (4)

Mounting

Holes (2)

Rubber Foot

Seat (4)

Adhesive

Strip Seat (2)

Cable

Channels

Mounting

Tabs (4)

Mounting

Holes (4)

Cable

Channels

Adhesive

Strip Seat (2)

Rubber

Foot Seat (4)

DATALOGIC

4

PORTABLE DESKTOP USE

1. Correctly position the BC-80X0 onto the base by sliding it along the

mounting tabs until aligned.

1

2

1

2

2. Carefully clean the rubber foot seats of the base to remove any impurities

that could reduce adhesion.

3. Remove the protective plastic from the rubber feet and stick them onto the

bottom surface of the base.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

FIXED DESKTOP USE

For fixed desktop installation, use the adhesive strips or fixing screws (not

provided) according to your needs.

For mounting with adhesive strips:

1. Position the cradle onto the base by sliding it along the mounting tabs until

aligned.

2. Carefully clean the adhesive strip seats of the base to remove any

impurities that could reduce adhesion.

3. Remove the protective plastic from one side of the adhesive strips and

stick them onto the base surface.

4. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels, as shown in the figures below:

Horizontal Base

Inclined Base

BC-80X0

5

5. Remove the plastic from the other side of the strips and affix the base to

the table.

6. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

For mounting with screws:

1. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels, as shown in the figures below:

2. Position the base on the table and affix it by means of the screws (not

provided).

3. Position the cradle on the base by sliding it along the mounting tabs until

aligned.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

Wall Mounting

1. Remove the yellow caps and insert the two wall mounting lock hinges

provided with your cradle.

DATALOGIC

6

2. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels (see figures at page 4).

If using the adhesive strips:

3. Carefully clean the adhesive strip

seats of the base to remove any

impurities that could reduce

adhesion.

4. Remove the protective plastic

from one side of the adhesive

strips and stick them onto the

base surface.

5. Remove the plastic from the

other side of the strips and affix

the base to the wall as indicated

in the figure below.

If using the mounting screws:

3. Using the mounting holes on the

base as a pattern, mark the wall

where you desire to mount the

BC-80X0.

4. Drill the appropriate size holes

and insert the threaded dowels

(not provided) into the holes.

5. Position the base on the wall as

indicated in the figure below and

affix it by means of the screws

(not provided).

Inclined Base Wall-mounting

6. Attach the cradle on the base by sliding it along the mounting tabs until

aligned.

7. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole

on the body of the cradle and screw it clockwise until tight.

BC-80X0

7

APPLYING RAPID POINT-TO-POINT CONFIGURATION

LABEL (OPTIONAL)

A pre-printed barcode label is included in the

package for rapid configuration of point-to-

point applications. If you wish to use this

method, apply this label to the seat provided

on the BC-80X0 cradle as shown in the

figure. See the Powerscan™ M8300 Quick

Reference Manual for the configuration

procedure.

SYSTEM CONNECTIONS

Connections should always be made with power off!

CAUTION

The BC-80X0 cradle provides two interface connectors and a power supply

connector as shown in the figure on the next page:

The RS-485 Network connection is available only on BC-8060 models. For

details about this type of connection, refer to the Powerscan™ D8330/M8300

Reference Manual.

To connect the BC-80X0 cradle to the Host through the multi-interface

connector, use the cable corresponding to the desired interface type.

Power Supply

RS-485

(BC-8060 only)

MULTI-INTERFACE

RS-232, USB, Wedge,

PEN Emulation

DATALOGIC

8

CONNECTING AND DISCONNECTING THE BC-80X0

INTERFACE CABLE

The BC-80X0 can be connected to a Host by means of an RS-232, USB, Wedge

or Pen cable, which must be simply plugged into the Host connector, visible on

the front panel of the cradle.

To disconnect the cable, insert a paper clip or other similar object into the hole

corresponding to the Host connector on the body of the cradle. Push down on the

clip while unplugging the cable. Refer to the following figure:

Connecting/Disconnecting the Cable

RS-232

USB

Power

Multi-standard interface

RS-232, USB, WEDGE, or

PEN Emulation to Host

BC-80X0

9

WEDGE

PEN

C-BOX

Powerscan™ M

BC-80X0

BIND

JOIN

C-BOX

Scanner

System cables to Host

DATALOGIC

10

BC-80X0 CONFIGURATION

The BC-80X0 configuration can be performed in three ways: by using the

Datalogic Aladdin™ software configuration program, by sending configuration

strings from the Host PC via the RS-232 or USB-COM interface or by reading

configuration barcodes with the Powerscan™ M reader.

DATALOGIC ALADDIN™

Datalogic Aladdin™ is a multi-platform utility program providing a quick and

user-friendly configuration method via the RS-232/USB-COM interface.

It also allows upgrading the software of the connected device (see the Datalogic

Aladdin™ Help On-Line for more details).

SERIAL CONFIGURATION

By connecting the BC-80X0 to a PC through an RS-232 or USB-COM interface

cable it is possible to send configuration strings from the PC to BC-80X0.

CONFIGURATION BARCODES

Once you have performed system connection and Powerscan™ M reader

configuration, you can configure the BC-80X0 cradle by reading configuration

barcodes. Apply power to the BC-80X0.

For Powerscan™ M configuration, refer to the “Powerscan™ M8300 Quick

Reference”.

To configure the BC-80X0 using the Powerscan™ M reader (the one paired to the

cradle with the Bind command), follow the procedure according to the interface

selected.

RESTORE DEFAULT

RESTORE BC-80X0 DEFAULT

Ì$+RX0$-qÎ

To change the defaults refer to the "Powerscan™ D8330/M8300 Reference

Manual", or to the Datalogic Aladdin™ Configuration program, both

downloadable from the website.

BC-80X0

11

INTERFACE SELECTION

Select one of the interface codes according to your application.

USB INTERFACE SELECTION

USB-KBD

Ì$+UA03$-:Î

USB-KBD – ALT-mode

Ì$+UA04$-@Î

USB-COM*

Ì$+UA02$-4Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

USB-IBM Table top

Ì$+UA00$-(Î

USB KBD-APPLE

* When configuring USB-COM, the relevant files and drivers must be installed

from the USB Device Installation Software, which can be downloaded from

the web site http://www.scanning.datalogic.com.

PEN EMULATION INTERFACE SELECTION

PEN

Ì$+CP6$-BÎ

DATALOGIC

12

INTERFACE SELECTION

Select one of the interface codes according to your application.

RS-232 INTERFACE SELECTION

RS-232 Standard

Ì$+CP0$-$Î

Nixdorf Mode A

Ì$+CM2EC0$->Î

Fujitsu

Ì$+CM1$-ÈÎ

ICL Mode

Ì$+CM0$-ÃÎ

WEDGE INTERFACE SELECTION

Wedge IBM AT or PS/2 PCs

Ì$+CP500$-aÎ

PC Notebook

Ì$+CP505$-ÈÎ

PC Notebook - ALT mode

Ì$+CP508$-2Î

IBM AT - ALT mode

Ì$+CP507$-+Î

Interfaces for IBM XT and IBM Terminals 3151, 347X and 348X can be selected

from the PowerScan D8330/M8300 Reference Manual available online at

http://www.datalogic.com.

BC-80X0

13

KEYBOARD NATIONALITY

USB-KBD and Wedge users should select one of the following wedge

keyboard nationality codes according to your keyboard.

Belge

Ì$+FJ7$-8Î

Deutsch

Ì$+FJ3$-$Î

English

Ì$+FJ4$-)Î

Español

Ì$+FJ6$-3Î

Français

Ì$+FJ2$-ÊÎ

Italiano

Ì$+FJ1$-ÅÎ

Svenskt

Ì$+FJ5$-.Î

USA (Default)

Ì$+FJ0$-|Î

DATALOGIC

14

The following Keyboard Nationality selections are only valid for IBM AT

compatible PCs:

Japanese

Ì$+FJ8$-=Î

Russian (Latin)

Ì$+FJ9$-BÎ

Russian (Cyrillic)

Ì$+FJA$-jÎ

Hungarian

Ì$+FJB$-oÎ

Slovenian, Croatian, Serbian (Latin)

Ì$+FJC$-tÎ

Romanian

Ì$+FJD$-yÎ

Czech Republic

Ì$+FJE$-~Î

BC-80X0

15

DATA FORMAT TERMINATORS

For your convenience, some common Terminators are given below. For other

Header/Terminators selections, Data Format and Advanced Data Format

parameters see the Powerscan™ D8330/M8300 Reference Manual.

CR-LF

Ì$+EA120D0A$-ÃÎ

Enter

Ì$+EA1183$-0Î

Tab

Ì$+EA1184$-8Î

None

Ì$+EA10$-dÎ

DATALOGIC

16

BC-80X0 DEFAULT CONFIGURATION

USB-KBD DEFAULT SETTINGS

USA keyboard, FIFO enabled, inter-character and inter-code delays disabled,

USB keyboard speed normal.

DATA FORMAT: code identifier disabled, code length not transmitted, character

replacement disabled, reader and cradle address stamping disabled, reader and

cradle address delimiter disabled, time stamping disabled, time stamping

delimiter disabled, no header, terminator = ENTER.

RS-232 DEFAULT SETTINGS

9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, ack/nack protocol

disabled, FIFO enabled, delay disabled, 5 sec. rx timeout

DATA FORMAT: code identifier disabled, code length not transmitted, character

replacement disabled, reader and cradle address stamping disabled, reader and

cradle address delimiter disabled, time stamping disabled, time stamping

delimiter disabled, no header, terminator = CR-LF.

WEDGE DEFAULT SETTINGS

USA keyboard, Caps Lock off, Caps Lock Auto-Recognition enabled, num lock

unchanged, inter-character and intercode delay disabled, control character

emulation = ctrl+shift+key.

DATA FORMAT: code identifier disabled, code length not transmitted, character

replacement disabled, reader and cradle address stamping disabled, reader and

cradle address delimiter disabled, time stamping disabled, time stamping

delimiter disabled, no header, terminator = ENTER.

PEN DEFAULT SETTINGS

Interpret operating mode, conversion to code 39, output level normal, idle level

normal, minimum output pulse 600 s, overflow medium, inter-block delay

disabled.

NETWORK PARAMETERS

RS-485 network disabled (for BC-8000 only).

BC-80X0

17

OPERATING TEST

Read the TEST codes below.

EAN-8

1 2 3 4 5 6 7 0

EAN-13

1 2 3 4 5 6 7 0 0 0 9 9 2

Code 39 (Normal)

1 7 1 6 2

Code 39 (Normal)

Code 128

t e s t

Interleaved 2 of 5

0 1 2 3 4 5 6 7 8 4

YOUR SYSTEM IS NOW READY TO READ CODES AND TO SEND THE

DATA TO THE HOST.

DATALOGIC

18

TECHNICAL FEATURES

BC-80X0

Electrical Features

Supply Voltage

External Power

10..30 VDC

Host Power

5 VDC ±10%

Power Consumption

External Power

max. 10 W (charging) *

Host Power

max. 500 mA (charging)

Indicators

Ext. Power/Data yellow LED

Host Power/Data yellow LED

Reader batt. state green/red LED

Spare batt. state green/red LED (BC-8060 only)

beeper

Time of Recharge

External Power

max. 4 hours with 2150 mAh Li-Ion battery

Host Power

max. 10 hours with 2150 mAh Li-Ion battery

Radio Features

European Models

USA Models

Radio frequency

433.92 MHz

910 MHz

Bit Rate

19200 baud

36800 baud

Range (in open air)

50 m

30 m

Environmental Features

Working Temperature

Radio

-20° to +50 °C / -4° to +122 °F

Battery Charging

0° to +40 °C / +32° to +104 °F

Storage Temperature

-20° to +70 °C / -4° to +158 °F

Humidity

90 % non condensing

Protection Class

IP40

Mechanical Features

Weight without mounting base

about 380 g / 13.4 oz

Dimensions (without antenna)

240 x 108 x 95 mm / 9.44 x 4.25 x 3.74 in

Material

ABS

* Having a switching regulator inside, the BC-80X0 draws the same power, regardless of

the supply voltage. i.e. as the input voltage increases the current drawn decreases.

System Configuration

BC-80X0

STARGATE™

Max number of devices per base

station

32

255

Max number of devices in the

same reading area

2000

BC-8060

STARGATE™

Max number of base stations in

network

16 (including cradle Master)

La pagina sta caricando ...

Datalogic BC-80X0 Cradle specificazione

Questo manuale è adatto anche per

Datalogic BC-80X0 Cradle specificazione

in altre lingue

Documenti correlati

Altri documenti