Datalogic PowerScan M8500 Quick Reference Manual

Marca: Datalogic

Modello: PowerScan M8500

Categoria: Lettori di codici a barre

Tipo: Quick Reference Manual

PowerScan™ M8500 Readers

Industrial Handheld Area Imager

Bar Code Reader with

Datalogic’s STAR Cordless System™

Quick Reference Guide

Datalogic ADC, Inc.

959 Terry Street

Eugene, OR 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

mentation or the procedures described therein may be reproduced or transmitted

in any form or by any means without prior written permission of Datalogic ADC,

Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”). Owners of Data-

logic products are hereby granted a non-exclusive, revocable license to reproduce

and transmit this documentation for the purchaser's own internal business pur-

poses. Purchaser shall not remove or alter any proprietary notices, including copy-

right notices, contained in this documentation and shall ensure that all notices

appear on any reproductions of the documentation.

Should future revisions of this manual be published, you can acquire printed ver-

sions by contacting your Datalogic representative. Electronic versions may either

be downloadable from the Datalogic website (www.datalogic.com) or provided on

appropriate media. If you visit our website and would like to make comments or

suggestions about this or other Datalogic publications, please let us know via the

"Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual

that is complete and accurate, however, Datalogic reserves the right to change any

specification at any time without prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in

many countries, including the U.S.A. and the E.U. All other brand and product

names may be trademarks of their respective owners.

Patents

This product may be covered by one or more of the following patents:

Design Pat. AU 310201; AU 310202; CN 693980; CN735959; HK 0602013.5M001; HK

0602013.5M002; JP 1305693; KR 30-0460940; US D570,843 S; USD588,596 S.

US Pat. 5,992,740; 6,305,606 B1; 6,517,003; 6,808,114 B1; 6,997,385 B2; 7,387,246 B2;

5,367,151; 5,449,893; 5,545,889; 6,098,877; 6,220,514 B1; 6,412,698 B2; 6,607,132 B1;

6,817,529 B2; 6,834,805 B2; 7,948,214 B2.

European Pat. 789,315 B1; 895,175 B1; 1,128,314 B1; 1,128,315 B1; 1,396,811 B1;

1,413,971 B1; 1,816,585 B1; 1,942,442 B1.

Additional patents pending.

Table of Contents

PowerScan™ M8500 Family ............................................................ 1

Description .....................................................................................................1

Using the PowerScan™ PM8500 Family ...............................................2

Indicators ........................................................................................................3

LED Indicators .......................................................................................3

Beeper......................................................................................................3

Good Read Spot ...................................................................................3

Charging the Batteries ...............................................................................4

Setup ................................................................................................................6

PowerScan™ M8500 Configuration .......................................................7

PowerScan™ M8500/BC-80X0 Point-to-Point Setup...............7

PowerScan™ M8500/BC-80X0 Stand Alone Setup...................8

Using Multiple Readers with Same Cradle................................11

PowerScan™ M8500/STAR-MODEM™ Stand Alone Setup ..11

PowerScan™ M8500/STAR-SYSTEM™ Setup.............................12

Default Configuration ..............................................................................15

Operating Test ............................................................................................16

Technical Features ....................................................................................17

Services and Support ...............................................................................22

Regulatory Information ...........................................................................23

Compliance..........................................................................................23

FCC Compliance.................................................................................23

Radio Compliance..............................................................................23

IC (Industry Canada)..........................................................................23

Power Supply ......................................................................................24

Laser Safety ..........................................................................................28

WEEE Compliance..............................................................................32

Datalogic ADC Limited Factory Warranty.................................33

Numeric Table .............................................................................................36

NOTES

Quick Reference Guide 1

PowerScan™ M8500 Family

Description

The PowerScan™ M8500 series readers can be used with either a BC-80X0 cradle

or Stargate™ radio base station to build a Cordless Reading System for the collec-

tion, decoding and transmission of bar coded data. The M8500 series can be used

in the same environment where M8300 series readers are already installed.

This manual includes just the commands required for the startup of the scanner

and setting of the interface. For complete configuration of the scanner, refer to the

PowerScan™ PM8500 Reference Manual or the Datalogic Aladdin configuration

program, both downloadable from the website and available on the included CD

ROM.

The PowerScan™ PM8500 Hand-Held Reader packs a lot of performance into

an attractive, rugged, hand-held device. It operates in commercial and industrial

environments, as well as the front office

Omni-

Directional

Operating

To read a symbol or capture an image, you simply aim the reader

and pull the trigger. Since the PowerScan™ PM8500 is a powerful

omni-directional reader, the orientation of the symbol is not

important.

Decoding

Thanks to powerful algorithms, PowerScan™ PM8500 reliably

decodes all major 1D (linear) bar codes, 2D stacked codes (such as

PDF417), 2D matrix symbols (such as DataMatrix), postal codes (such

as POSTNET, PLANET). The data stream — acquired from decoding a

symbol — is rapidly sent to the host. The reader is immediately

available to read another symbol.

Formatting and

Concatenating

The string of a decoded code may be processed according to

either a simple or advanced data formatting and be concatenated

to other codes (up to 4 different codes).

Autoscanning

An autoscan command causes the reader to scan continuously and

to monitor the central zone of its reading area.

Flash Memory

Flash technology allows you to upgrade the PowerScan™ PM8500

reader as new symbologies are supported or as improved

decoding algorithms become available.

USA Driver

License Parsing

The reader can be set up to select and output a subset of data

elements from USA Driver License PDF417 bar codes. This feature

can be enabled using either Datalogic Aladdin™ or the bar codes in

the USA Driver License Parsing Quick Reference Guide (QRG),

available on the Datalogic website.

The Powerscan M8500 is compatible with BC80x0 v3.0.0.00 (available in

the Aladdin Software on the CD included with this product) and later

releases. If a previous firmware version is installed in your BC80x0, please

upgrade to the latest version before installing the M8500.

Using the PowerScan™ PM8500 Family

2PowerScan™ M8500

Using the PowerScan™ PM8500 Family

The PowerScan™ PM8500 normally functions by capturing and decoding codes.

The PowerScan™ PM8500 reader uses an intelligent aiming system. By pulling

the trigger, the aiming system indicates a field of view, which should be positioned

over the code:

Aiming System

When you pull the trigger, a red beam illuminates the code. If the aiming system

is centered and the entire symbology is within the aiming system, you will get a

good read. The field of view changes size as you move the reader closer or farther

away from the code.

Relative Size and Location of Aiming System Pattern

Successful reading is signaled by an audible tone plus a good-read green LED.

The PowerScan™ PM8500 handheld reader aiming system is designed for

general reading and decoding of 1D and 2D symbols. Some variation in

reading distance will occur due to narrow bar width and other factors.

If reading codes positioned on reflective surfaces, it may be necessary to

tilt the reader with respect to the bar code and/or set the Camera Control

parameters. For configuring the Camera Control parameters refer to the

PowerScan™ PM8500 Product Reference Guide (PRG) available on the

website and the CD.

Linear bar code

2D Matrix symbol

Indicators

Quick Reference Guide 3

Indicators

LED Indicators

The PowerScan™ PM8500 family uses green LED indicators to signal the follow-

ing reader functions:

Beeper

The PowerScan™ PM8500 basic software provides beeper signals for good/wrong

reading and for indicating errors. Its tone, volume and duration can be directly

configured by using the codes given in the PowerScan™ PM8500 Product Refer-

ence Guide (PRG) available on the website.

The application program can also manage the beeper (User Defined Beeper) when

the reader is controlled by a Host PC. It is possible to activate the beeper by send-

ing a command from the Host to the reader via the current communication inter-

face.

Good Read Spot

A green good read spot will be projected in the field of view when the reading is

successful.

STATUS BEHAVIOR

Power ON At power-on, the LEDs blink briefly, then light up for 2

seconds to signal the power supply is present.

Normal Function The LED lights up after a good decoding and will

switch off only at the next trigger press.

Charging the Batteries

4PowerScan™ M8500

Charging the Batteries

Once the BC-80X0/C-8000 is powered, you can charge the reader's batteries.

Place the PowerScan™ M8500 into the BC-80X0 cradle or the C-8000 battery

charger. The "Reader" LED on the cradle/battery charger turns red.

The battery is completely charged when the "Reader" LED on the cradle/battery

charger turns green.

To change the battery, push the Release Button as indicated by Arrow 1 and

extract the battery pack from the reader handle. Then, insert the new battery pack

into the reader handle until a ‘click’ is heard and the Release Button moves back to

its neutral position.

Charging the Batteries

Quick Reference Guide 5

As with other types of batteries, Lithium-Ion (LI) batteries will lose capacity over time. Capacity deteri-

oration is noticeable after one year of service whether the battery is in use or not. It is difficult to pre-

cisely predict the finite life of a LI battery, but cell manufacturers rate them at 500 charge cycles. In

other words, the batteries should be expected to take 500 full discharge/charge cycles before needing

replacement. This number is higher if partial discharging / recharging is adhered to rather than full /

deep discharging,

The typical manufacturer advertised useful life of LI batteries is one to three years, depending on

usage and number of charges, etc., after which they should be removed from service, especially in mis-

sion critical applications. Do not continue to use a battery that is showing excessive loss of capacity, it

should be properly recycled / disposed of and replaced. For most applications, batteries should be

replaced after one year of service to maintain customer satisfaction and minimize safety concerns.

Collect and recycle waste batteries separately from the device in compliance with European Directive

2006/66/EC, 2011/65/EU, 2012/19/EU. and subsequent modifications, US and China regulatory and oth-

ers laws and regulations about the environment.

WARNING

Do not discharge the battery using any device except for the scanner.

When the battery is used in devices other than the designated product, it

may damage the battery or reduce its life expectancy. If the device causes

an abnormal current to flow, it may cause the battery to become hot,

explode or ignite and cause serious injury.

Lithium-ion battery packs may get hot, explode or ignite and cause seri-

ous injury if exposed to abusive conditions. Be sure to follow the safety

warnings listed below:

• Do not place the battery pack in fire or heat.

• Do not connect the positive terminal and negative terminal of the battery pack

to each other with any metal object (such as wire).

• Do not carry or store the battery pack together with metal objects.

• Do not pierce the battery pack with nails, strike it with a hammer, step on it or

otherwise subject it to strong impacts or shocks.

• Do not solder directly onto the battery pack.

• Do not expose the battery pack to liquids, or allow the battery to get wet.

• Do not apply voltages to the battery pack contacts.

In the event the battery pack leaks and the fluid gets into your eye, do not

rub the eye. Rinse well with water and immediately seek medical care. If

left untreated, the battery fluid could cause damage to the eye.

CAUTION

Always charge the battery at 32° – 104°F (0° - 40°C) temperature range.

Use only the authorized power supplies, battery pack, chargers, and

docks supplied by your Datalogic reseller. The use of any other power

supplies can damage the device and void your warranty.

Do not disassemble or modify the battery. The battery contains safety

and protection devices, which, if damaged, may cause the battery to

generate heat, explode or ignite.

Do not place the battery in or near fire, on stoves or other high tempera-

ture locations.

Do not place the battery in direct sunlight, or use or store the battery

inside cars in hot weather. Doing so may cause the battery to generate

heat, explode or ignite. Using the battery in this manner may also result

in a loss of performance and a shortened life expectancy.

Do not place the battery in microwave ovens, high-pressure containers

or on induction cookware.

Immediately discontinue use of the battery if, while using, charging or

storing the battery, the battery emits an unusual smell, feels hot,

changes color or shape, or appears abnormal in any other way.

Do not replace the battery pack when the device is turned on.

Do not remove or damage the battery pack’s label.

Do not use the battery pack if it is damaged in any part.

Battery pack usage by children should be supervised.

Setup

6PowerScan™ M8500

Setup

PowerScan™ M8500/BC-80X0 Point-to Point Configuration

1. Connect a BC-80X0 cradle to the Host. For installation and connection

information see the BC-80X0 Quick Reference Manual.

2. Charge the PowerScan™ M8500 battery using an BC-80X0 or the

C-8000 char

ger as described in this Quick Reference manual. A full

charge takes 4 hours if using an external power supply; while it takes up

to 10 hours if supplying power through the USB port.

3. Configure the reader as described in this Quick Reference -

PowerScan™ M8500/BC-80X0 Point-to-Point Setup.

4. Configure the BC-80X0 cradle. See BC-80X0 Configuration in the BC-

80X0 Quick Reference.

PowerScan™ M8500/BC-80X0 Stand Alone Configuration

1. Connect an BC-80X0 cradle to the Host. For installation and connection

information see the BC-80X0 Quick Reference Manual.

2. Charge the PowerScan™ M8500 battery using an BC-80X0 or the

C-8000 char

ger as described in this Quick Reference manual. A full

charge takes 4 hours if using an external power supply; while it takes up

to 10 hours if supplying power through the USB port.

3. Configure the reader as described in this Quick Reference -

PowerScan™ M8500/BC-80X0 Stand Alone Setup.

4. Configure the BC-80X0 cradle. See BC-80X0 Configuration in the

BC-80X0 Quick Reference.

PowerScan™ M8500/STAR-System™ Configuration

1. Charge the PowerScan™ M8500 battery using an BC-8000 or the

C-8000 charger as described in this Quick Reference manual. A full

charge takes 4 hours if using an external power supply; while it takes up

to 10 hours if supplying power through the USB port.

2. Configure the reader as described in this Quick Reference -

owerScan™ M8500/STAR-System™ Setup.

PowerScan™ M8500 Configuration

Quick Reference Guide 7

PowerScan™ M8500 Configuration

PowerScan™

M8500/BC-80X0 Point-to-Point Setup

A rapid configuration procedure has been devised for point-to-point applications

where a single reader is associated exclusively with its own BC-80X0 base station

and where it is not necessary to set the Date and Time parameters.

A special pre-printed bind-address label provided in the BC-80X0 base station

package can be used to bind the PowerScan™ M8500 reader to the base station

with the address coded on the label. The address is also written numerically on the

label to be easily recognized. Valid addresses are in the range from 0000 to 1999.

Make sure that all cradles used in the same area have different addresses.

To rapidly configure your point-to-point application:

1. Apply the bind-address label onto the

BC-80X0 base station as indicated

in the BC-80X0 Quick Reference Manual.

2. When the BC-80X0 cradle is connected

and powered, read the Bind-

Address label to pair the PowerScan™ M8500 to the BC-80X0 cradle.

The green LED on the PowerScan™ M8500 will blink: the reader is ready

to be positioned onto the cradle.

3. Firmly position the reader onto the cradle within 10 seconds, a beep will

be emitted, signaling that the BC-80X0 cradle has been paired to the

PowerScan™ M8500, and the green LED on the reader will go off.

4. Configure the BC-80X0 cradle, refer to the “BC-80X0 Quick Reference”.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

If it ever becomes necessary to

change

the reader, just read the

bind-address label applied to the

cradle and position the new reader

onto the cradle.

Do not use multiple readers with

this configuration method.

Green LED

PowerScan™ M8500 Configuration

8PowerScan™ M8500

PowerScan™ M8500/BC-80X0 Stand Alone Setup

When the BC-80X0 cradle is connected and powered, configure the PowerScan™

M8500 by reading the following codes in the given sequence and follow the instruc-

tions.

For the numeric code selection of steps 3, 4, and 5 use the table at the end

of this Quick Reference

1. Restore PowerScan™ M8500 Default

2. Enter Configuration

3. Set Date

six digits for Day, Month and Year (DDMMYY).

4. Set Time

PowerScan™ M8500 Configuration

Quick Reference Guide 9

four digits for Hours and Minutes (HHMM).

5. Set Radio Address

four digits for the PowerScan™ M8500 Address

(from 0000 to 1999).

All readers used in the same area must have different addresses.

6. Exit and Save Configuration

7. Read the Bind code to pair the PowerScan™ M8500 to the BC-80X0 cradle.

The reader is dedicated to the cradle. Any previously bound reader will be

excluded.

To connect several readers to the same cradle see the following section "Using

Multiple Readers with Same Cradle".

Bind

The green LED on the PowerScan™ M8500 will blink: the reader is ready to be

positioned onto the cradle.

8. Firmly position the reader onto the cradle within 10 seconds, a beep will be

emitted, signaling that the BC-80X0 cradle has been paired to the

PowerScan™ M8500, and the green LED on the reader will go off.

PowerScan™ M8500 Configuration

10 PowerScan™ M8500

END of procedure. YOUR READER IS NOW READY TO READ CODES.

9. Configure the BC-80X0 cradle, refer to the “BC-80X0 Quick Reference”.

Green LED

PowerScan™ M8500 Configuration

Quick Reference Guide 11

Using Multiple Readers with Same Cradle

If you want to use several readers associated with the same cradle, you must first

Bind the cradle with one of the readers (see previously described configuration

procedure).

Successive readers can be associated with the same cradle by following the con-

figuration procedure substituting the Bind command with Join.

END of procedure.

PowerScan™

M8500/STAR-MODEM™ Stand Alone Setup

To configure a PowerScan™ M8500 reader to communicate with STAR-

Modem™ in Stand Alone Mode, follow the "PowerScan™ M8500/BC-80X0

Stand Alone Setup" procedure substituting steps 5 and 6 with those below:

END of procedure. YOUR READER IS NOW READY TO READ CODES.

7. Join

The g

reen LED on the PowerScan™ M8500 will blink: the reader is ready to be

positioned onto the cradle. Complete step 8.

CAUTION

All readers associated with the same cradle must have different

addresses.

6. STAR-Modem™ Address

Read the code above and the four-digit address of the STAR-Modem™.

7. Exit and Save Configuration

PowerScan™ M8500 Configuration

12 PowerScan™ M8500

PowerScan™

M8500/STAR-SYSTEM™ Setup

The following procedure allows configuring a PowerScan™ M8500 reader to

communicate with various STAR-System™ devices such as Stargate™ RF base

stations:

1. Restore PowerScan™ M8500 Default

2. Enter Configuration

3. Set Date

six digits for Day, Month and Year (DDMMYY).

4. Set Time

four digits for Hours and Minutes (HHMM).

PowerScan™ M8500 Configuration

Quick Reference Guide 13

5. Set the connection according to the length of the codes to be read:

Code Length 240 Characters

Code Length 240 Characters

(not for systems with BC-80X0 as Master)

6. Set Radio Address

four digits from the Numeric Table for the PowerScan™ M8500 Address

(from 0000 to 1999).

All readers used in the same area must have different addresses.

7. Set First STAR-System™ Address

four digits from the Numeric Table in the range 0000 to 1999

PowerScan™ M8500 Configuration

14 PowerScan™ M8500

END of procedure. YOUR READER IS NOW READY TO READ CODES.

8. Set Last STAR-System™ Address

four digits from the Numeric Table in the range 0000 to 1999

Whenever the system is composed of a single base station, the first

and last base station addresses (steps 7 and 8) must have the same

value.

9. Exit and Save Configuration

Default Configuration

Quick Reference Guide 15

Default Configuration

DATA FORMAT – Symbology Dependent Parameters

symbology specific format = select all, no headers, no terminators, symbology character

substitution disabled, symbology character deletion disabled

DATA FORMAT – Concatenation

Concatenation disabled, 2 EAN/UPC codes concatenated, Set First Concatenated Code

Length 000 = any length, Set Second Concatenated Code Length 000 = any length, Set

Third Concatenated Code Length 000 = any length, Set Fourth Concatenated Code Length

000 = any length, Concatenation with Intercode Delay disabled, Concatenation Timeout 10

seconds, Concatenation Failure Transmission = Tx codes causing failure, Transmission after

Timeout = No code transmission, Concatenation Result Code ID = No code Identifier

ADVANCED FORMATTING PARAMETERS

format disabled

CAMERA CONTROL

exposure mode = automatic, based on entire image

CODE SELECTION

issue identical codes = enable

enabled codes

Standard Code 39: no check digit control, variable code length;

EAN 8/EAN 13 / UPC A/UPC E without ADD ON

: UPCE expansion disabled

Code 128

: variable code length

PDF417

Datamatrix: rectangular, normal and inverted, variable code length

disabled codes

Code 32, Interleaved 2/5, Codabar, Code 93, EAN 128, GS1 DataBar™, Micro PDF417, Postal

Codes, Maxicode, Composite Codes

Aztec, microQR, IMB.

READING PARAMETERS

trigger type normal, trigger level mode, flash on = 2 sec, flash off = 2 sec, beeper tone =

tone 1, beeper volume = high, beeper duration = 50 ms, user defined beeper = tone 1, user

defined beeper volume = high, user defined beeper duration = 100 ms, code per scan = one

code per scan, read per cycle = one read per cycle, scan timeout = 5 sec, central code

transmission = disabled, order by code length = disabled, order by code symbology =

disabled, autoscan mode = disabled, autoscan aiming system = enabled, autoscan

hardware trigger = enabled, autoscan illumination system = disabled, stand autoscan mode

= normal, aiming system delay = disabled, good read spot = short, safety time = 500 ms

RADIO PARAMETERS

radio protocol timeout = 2 seconds, power-off timeout = 4 hours, transmission mode =

one-way, beeper control for radio response = normal, single store = disabled, batch mode =

disabled, find me = enabled, radio RX timeout = disabled

Operating Test

16 PowerScan™ M8500

Operating Test

EAN-13 Code 39 (Standard)

Code 128

PDF417

Data Matrix (Normal)

1 234567 000992

17162

test

La pagina si sta caricando...

Datalogic PowerScan M8500 Quick Reference Manual

Marca: Datalogic

Modello: PowerScan M8500

Categoria: Lettori di codici a barre

Tipo: Quick Reference Manual

Scarica PDF

rapporto

in altre lingue

English: Datalogic PowerScan M8500

Datalogic PowerScan M8500 Quick Reference Manual

Datalogic PowerScan M8500 Quick Reference Manual

in altre lingue

Documenti correlati

Altri documenti