Yamaha R-S202 Manuale del proprietario

CRBGL

ES

FR

EN

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

Receiver

Ampli-Tuner

EnglishFrançaisEspañol

i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade

or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been

dropped.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain

this Owner’s Manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is

often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group

recommend you to avoid prolonged exposure from excessive volume levels.

English

IMPORTANT SAFETY INSTRUCTIONS

ii En

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2 IMPORTANT:

When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact

Yamaha Corporation of America A/V Division, 6600

Orangethorpe Avenue, Buena Park, CA 90620, USA.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

CAN ICES-3 (B)/NMB-3(B)

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio

frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very

low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable

that it should be installed and operated with at least 20 cm and more between the radiator and person’s body.

FCC CAUTION

Change or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

Do not use this unit within 22 cm (9 inches) of persons with a

heart pacemaker implant or defibrillator implant.

Radio waves may affect electro-medical devices.

Do not use this unit near medical devices or inside medical

facilities.

This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to an AC wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the AC wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 VOLTAGE SELECTOR (General model)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging into the AC wall outlet. Voltages are:

.................................... AC 110-120/220-240 V, 50/60 Hz

14 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from an AC wall

outlet or this unit during a lightning storm.

15 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

16 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the AC wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

18 Before moving this unit, press A (power) to set this unit

to standby mode, and then disconnect the AC power plug

from the AC wall outlet.

19 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

20 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

21 Install this unit near the AC wall outlet and where the AC

power plug can be reached easily.

22 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

23 Excessive sound pressure from earphones and

headphones can cause hearing loss.

This label is required to be attached to a product of which

the temperature of the top cover may be hot during

operation.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed,

as a plug with bared flexible cord is hazardous if engaged

in a live socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as

it is connected to the AC wall outlet, even if this unit itself is turned

off by A. This state is called the standby mode. In this state, this

unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth terminal of the

three pin plug.

English

1 En

USEFUL FEATURES............................................... 1

SUPPLIED ACCESSORIES.................................... 1

CONTROLS AND FUNCTIONS ............................ 2

Front panel.................................................................... 2

Front panel display ....................................................... 4

Rear panel..................................................................... 5

Remote control ............................................................. 6

Using the remote control .............................................. 8

CONNECTIONS ....................................................... 9

Connecting speakers and source components .............. 9

Connecting the FM/AM antennas (R-S202)............... 11

Connecting the DAB/FM antennas (R-S202D).......... 11

Connecting power cable ............................................. 11

PLAYBACK ............................................................ 12

Playing a source.......................................................... 12

Using the sleep timer .................................................. 12

LISTENING TO MUSIC FROM YOUR

Bluetooth DEVICE .................................................. 13

Playing back from your Bluetooth device .................. 13

Connecting an already-paired device via Bluetooth ... 14

Disconnecting a Bluetooth connection ....................... 14

FM/AM TUNING (R-S202) ....................................15

Using preset functions ................................................ 15

Receiving Radio Data System information

(Only for Europe model) ........................................ 19

FM TUNING (R-S202D) .........................................20

Using preset functions ................................................ 20

Receiving Radio Data System information

(Only for U.K. and Europe models)....................... 24

LISTENING TO DAB RADIO (R-S202D)............25

Preparing the DAB tuning .......................................... 25

Selecting a DAB radio station for reception............... 25

Using preset function.................................................. 26

Displaying the DAB information ............................... 28

Checking reception strength of each DAB channel

label ........................................................................ 29

SETTING THE OPTION MENU FOR EACH

INPUT SOURCE .....................................................30

Option menu items ..................................................... 30

TROUBLESHOOTING ..........................................31

SPECIFICATIONS .................................................35

■ About this manual

• y indicates a tip for your operation.

• The instructions in this manual describe the operation of this unit with the supplied remote control. You can also use the buttons or

knobs on the front panel if they have the same or similar names as those on the remote control.

• AM radio is available only for R-S202.

This unit allows you to:

◆ Enjoy clear audio sound wirelessly using Bluetooth

technology (see page 13).

◆ (R-S202) Listen to FM and AM radio stations

(see page 15).

◆ (R-S202D) Listen to FM and DAB radio stations

(see pages 20, 25).

◆ Use the remote control of this unit to operate a Yamaha

CD player (see page 7).

◆ Save power by using the AUTO POWER STANDBY

function (see page 30).

Please check that you received all of the following parts.

CONTENTS

USEFUL FEATURES

SUPPLIED ACCESSORIES

Remote control AM antenna (R-S202)

Batteries (x2)

(AA, R6, UM-3)

FM antenna (R-S202)

*

One of the above is supplied depending

on the region of purchase.

DAB/FM antenna (R-S202D)

2 En

1 A (power)

Turns this unit on, or sets it to standby mode.

2 FM MODE

Changes the FM radio wave reception mode (stereo or

monaural) when TUNER is selected as the input

source (see pages 15, 20).

3 Remote control sensor

Receives infrared signals from the remote control.

4 STANDBY/ON indicator

5 MEMORY

Stores the current radio station as a preset when

TUNER is selected as the input source (see

pages 16, 21).

6 BAND

Sets the radio tuner band when TUNER is selected as

the input source (see pages 15, 20).

7 PRESET j / i

Selects a preset radio station when TUNER is selected

as the input source (see pages 17, 22).

8 TUNING jj / ii

Selects the tuning frequency when TUNER is selected

as the input source (see pages 15, 20).

9 Bluetooth indicator

Indicates the status of the connection with the

Bluetooth device (see page 13).

0 Front panel display

Shows information about the operational status of this

unit (see page 4).

CONTROLS AND FUNCTIONS

Front panel

BAND

1 254 9 03 6

A

B

F

C D E

7 8

Indicator Status

Brightly lit

The power of this unit is “on”.

Dimly lit

This unit is in “standby” mode.

Off

The power of this unit is “off”.

To turn off this unit, disconnect

the power cable from an AC

wall outlet.

English

CONTROLS AND FUNCTIONS

3 En

A PHONES jack

For connecting headphones.

y

Press SPEAKERS A/B so that the SP A/B indicators (see

page 4) turn off before you connect your headphones to the

PHONES jack.

B SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel each time the corresponding button is

pressed (see

page 12

).

C BASS –/+

Increases or decreases the low frequency response.

Control range: –10 dB to +10 dB

D TREBLE –/+

Increases or decreases the high frequency response.

Control range: –10 dB to +10 dB

E INPUT l / h

Selects the input source you want to listen to.

F VOLUME control

Increases or decreases the sound output level.

CONTROLS AND FUNCTIONS

4 En

[AM radio is available only for R-S202.]

1 PRESET indicator

Lights up or blinks when using the preset function

(see pages 16, 21).

2 MEMORY indicator

Lights up or blinks when registering radio stations as

presets (see pages 16, 21).

3 SP (SPEAKERS) A/B indicators

Light up according to the set of speakers selected.

Both indicators light up when both sets of speakers are

selected.

4 TUNED indicator

Lights up when this unit is tuned in to an FM or AM

station with a strong signal.

5 SLEEP indicator

Lights up when the sleep timer is turned on (see

page 12).

6 ST indicator

Lights up when this unit is in stereo mode and tuning

in an FM station with a stereo broadcast.

7 kHz/MHz indicators

Lights up according to the current broadcast

frequency.

kHz: AM

MHz: FM

8 Multi-information display

Shows information when adjusting or changing

settings.

Front panel display

English

CONTROLS AND FUNCTIONS

5 En

[AM radio is available only for R-S202.]

1 ANTENNA terminals

Used to connect the radio antennas (see page 11).

2 Power cable

For connecting this unit to an AC wall outlet (see

page 11).

3 CD jacks

Used to connect a CD player (see page 9).

4 LINE 1-2 jacks

Used to connect audio components (see page 9).

5 LINE 3 jacks

IN jacks

Used to connect to audio output jacks of an audio

component (see page 9).

OUT jacks

Used to connect to audio input jacks of an audio

component (see page 9).

6 SPEAKERS terminals

Used to connect speakers (see page 9).

7 VOLTAGE SELECTOR

(Only for General model)

Rear panel

7634 5

21

CONTROLS AND FUNCTIONS

6 En

■ Common controls

The following parts and controls can be used no matter

which input source is selected.

1 Infrared signal transmitter

Sends infrared signals.

2 A (power)

Turns this unit on, or sets it to standby mode.

3 SLEEP

Sets the sleep timer (see page 12).

4 Input selector buttons

Select the input source you want to listen to.

y

The input source names correspond to the names of the

connection jacks on the rear panel.

5 TREBLE –/+

Increases or decreases the high frequency response.

Control range: –10 dB to +10 dB

6 BASS –/+

Increases or decreases the low frequency response.

Control range: –10 dB to +10 dB

7 BALANCE L/R

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances.

Control range:

8  /  /  /  / ENTER

Selects and confirms items in the Option menu

(see page 30).

9 MENU

Turns the Option menu on and off (see page 30).

0 VOLUME +/–

Increases or decreases the sound output level.

A SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel each time the corresponding button is

pressed (see

page 12

).

B DIMMER

Select the brightness level of the front panel display

from 3 levels by pressing this button repeatedly.

y

• This setting is retained even if you turn off this unit.

• The default setting is the brightest.

C MUTE

Mutes the sound output. Press again to restore the

sound output to the previous volume level.

Remote control

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

TREBLE

SPEAKERS

B

A

R

BASS

MENU

DIMMER

MUTE

VOLUME

DISC SKIP

BALANCE

BLUETOOTH

ENTER

MEMORY

INFO

BAND

LINE 2 LINE 3

1

2

3

9B

C

E

A

4

5

6

0

7

8

D

(+20 dB) (center) (+20 dB)

The opposite side of

channel is muted.

The opposite side of

channel is muted.

English

CONTROLS AND FUNCTIONS

7 En

■ Radio function controls

The following buttons can be used when TUNER is

selected as the input source.

D TUNING jj / ii

Selects the tuning frequency (see pages 15, 20).

PRESET j / i

Selects a preset radio station (see pages 17, 22).

BAND

Switches the radio tuner band.

MEMORY

Stores the current radio station as a preset (see

pages 16, 21).

INFO

Only for U.K. and Europe models:

Switches information shown on the front panel

display.

■ Yamaha CD player controls

The following buttons can be used to control a Yamaha

CD player.

E Yamaha CD player control buttons

s Stops playback

e Pauses playback

p Starts playback

DISC SKIP Skips to the next disc in a CD changer

b Skips backward

a Skips forward

Ejects the disc

w Rewinds playback

f Fast-forwards playback

Even when using a Yamaha CD player, certain components and

features may not be available. Refer to your component’s owner’s

manual for more information.

■ Bluetooth controls

The following buttons can be used to control a Bluetooth

device.

8 Bluetooth control buttons

BLUETOOTH Switches the audio source to

Bluetooth

I Skips backward

I Skips forward

II Starts/pauses playback

Yamaha does not guarantee the operation of all Bluetooth devices.

Note

CONTROLS AND FUNCTIONS

8 En

■ Installing batteries

Change all batteries if you notice the operation range of

the remote control narrows. Before inserting new

batteries, wipe the battery compartment clean.

■ Operation rang e

Point the remote control at the remote control sensor on

this unit and remain within the operating range shown

below. The area between the remote control and this unit

must be clear of large obstacles.

• Be careful not to drop the remote control.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a

different specification.

• Dispose of batteries according to your regional regulations.

• Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or her mouth.

• If you plan not to use this unit for a long period of time, remove the batteries from this unit. Otherwise, the batteries will wear out,

possibly resulting in a leakage of battery liquid that may damage this unit.

Using the remote control

AA, R6, UM-3 batteries

Approximately

6 m (20 ft)

Remote control

CAUTION

English

9 En

Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will

be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and

lack bass. Refer to the owner’s manual for each of your components.

Make sure to use RCA cables to connect audio components.

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the

speakers.

CONNECTIONS

Connecting speakers and source components

CAUTION

Audio

out

CD recorder,

etc.

DVD player,

etc.

Audio

out

Left

Audio

out

Audio

out

Audio

in

Speakers B

Tape deck, etc.

CD player

Speakers A

Right

LeftRight

(R-S202)

10 En

CONNECTIONS

■ OUT jacks

• The OUT jacks output audio signals of the currently

selected input (except when LINE 3 is selected).

• Volume level, tone control and balance settings do not

affect the OUT jacks.

■ Connecting speaker cables

When inserting speaker cables into the speaker terminals, insert

only the bare speaker wire. If insulated cable is inserted, the

connection may be poor and sound may not be heard.

Connect the speakers with an impedance as shown below.

If you connect speakers with an excessively low

impedance, this unit may overheat.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section.

A bi-wire compatible speaker has four binding post

terminals. These two sets of terminals allow the speaker to

be split into two independent sections. With these

connections, the mid and high frequency drivers are

connected to one set of terminals and the low frequency

driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B so that both SPA and B light up on the front panel

display.

Note

CAUTION

Speaker connection Speaker impedance

SPEAKERS A or

SPEAKERS B

8  or higher

SPEAKERS A and

SPEAKERS B

16  or higher

(except for North

America model)

Bi-wiring

8  or higher

Remove approximately

10 mm (3/8 in) of

insulation from the end of

each speaker cable.

Note

Rear panel

Speaker

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

TREBLE

SPEAKERS

R

BASS

BALANCE

MEMORY

INFO

BAND

LINE 2 LINE 3

B

A

B

A

SPEAKERS A/B

English

11 En

CONNECTIONS

Connect the supplied FM/AM antenna to this unit.

Fix the end of the FM antenna to a wall, and place the AM

antenna.

• If you experience poor reception quality, install an outdoor

antenna.

• Unwind only the length of cable needed from the AM antenna

unit.

• The wires of the AM antenna have no polarity.

■ Assembling the AM antenna

■ Connecting the wire of the AM antenna

Connect the supplied DAB/FM antenna to this unit and fix

the antenna ends to a wall.

• If you experience poor reception quality, install an outdoor

antenna.

• The antenna should be stretched out horizontally.

Plug the power cable into an AC wall outlet after all other

connections are complete.

Only for General model:

Before connecting the power cable, make sure you set

VOLTAGE SELECTOR of this unit according to your

local voltage. Improper setting of VOLTAGE SELECTOR

may cause fire and damage to this unit.

Connecting the FM/AM antennas

(R-S202)

Notes

FM antenna AM antenna

Connecting the DAB/FM antennas

(R-S202D)

Notes

Connecting power cable

CAUTION

DAB/FM antenna

To the AC wall

outlet with the

power cable

12 En

1 Press A (power) to turn on this unit.

2 Press one of the Input selector buttons to

select the desired input source.

3 Press SPEAKERS A and/or SPEAKERS B to

select the desired speaker(s).

y

• When one set of speakers is connected using bi-wire

connections, or when using two sets of speakers

simultaneously (A and B), make sure SP A and SP B are

displayed on the front panel display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Press VOLUME +/– to adjust the sound

output level.

y

You can adjust the tonal quality by using BASS –/+ and

TREBLE –/+, and the left/right sound balance of speakers

by using BALANCE L/R (see page 6).

6 When finished listening, press A (power) to

set this unit to standby mode.

Press A (power) to turn this unit on again.

y

• You can also use the buttons or knobs on the front panel if

they have the same or similar names as those on the

remote control.

• For recording, see page 5.

Use this feature to automatically set this unit to standby

mode after a certain amount of time. The sleep timer is

useful when you are going to sleep while this unit is

playing or recording a source.

Press SLEEP repeatedly to set the time duration

until the unit enters standby mode.

Each time you press SLEEP, the time duration indicated

on the front panel display changes cyclically as shown

below.

The SLEEP indicator blinks while setting the amount of

time for the sleep timer.

If the sleep timer is set, the SLEEP indicator on the front

panel display lights up.

y

To cancel the sleep timer, do one of the following:

– Select “SLEEP OFF”.

– Press A (power) to set this unit to standby mode.

PLAYBACK

Playing a source

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

TREBLE

SPEAKERS

R

BASS

MENU

DIMMER

MUTE

VOLUME

BALANCE

BLUETOOTH

ENTER

MEMORY

INFO

BAND

LINE 2 LINE 3

B

A

R

B

A

A (power)

Input selector

buttons

SPEAKERS A/B

VOLUME +/–

TREBLE –/+

BASS –/+

BALANCE L/R

Using the sleep timer

SLEEP

LINE 1

CD TUNER

BAND

LINE 2 LINE 3

A (power)

SLEEP

120 min 90 min

60 min30 minoff

English

13 En

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device (mobile

phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.

You’ll need to perform the pairing operation the first time

you use your Bluetooth device with this unit, or if the

pairing settings have been deleted. Pairing is an operation

that registers the Bluetooth device with this unit. If pairing

is not successful, refer to the item “Bluetooth” in

“TROUBLESHOOTING” (see page 32).

• Yamaha does not guarantee all connections between this unit

and Bluetooth device.

• This unit can be paired with up to 8 Bluetooth devices. When

pairing with the 9th device has succeeded, pairing data for the

device with the oldest connection date will be deleted.

• While connecting to the Bluetooth device and perform the

pairing with another device, the current Bluetooth connection

will be canceled.

1 Press the BLUETOOTH source button for

more than 3 seconds to enter pairing mode.

• Pairing mode lasts for 5 minutes.

• In pairing mode, the front panel display of this unit

will indicate “PAIRING,” and the Bluetooth

indicator will blink.

y

You can also enter pairing mode in either of the following

two ways:

– Press and hold down INPUT l or h on this unit for

three seconds.

– Select “PAIRING” from the Option menu, and then

press ENTER (see page 30).

2 Turn on the Bluetooth function on the

Bluetooth device.

For details refer to the owner’s manual of the

Bluetooth device.

3 From the Bluetooth connection list of the

Bluetooth device, choose this unit (R-S202

Yamaha or R-S202D Yamaha).

• When pairing has been completed, the front panel

display of this unit will indicate “COMPLETED”.

• When the Bluetooth device is connected, the front

panel display of this unit will indicate

“CONNECTED” and the Bluetooth indicator will

light up.

y

If you are asked to enter a password, enter the numerals

“0000”.

4 Play back music from the Bluetooth device.

• Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the Bluetooth device.

• If Bluetooth is selected as the audio source, this unit will

automatically turn off when 20 minutes have elapsed without

any Bluetooth connection nor any operation performed.

y

You can use the Bluetooth control buttons on the remote control

to control playback (see page 7).

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

Playing back from your Bluetooth

device

Notes

R

MENU

DIMMER

MUTE

VOLUME

BALANCE

BLUETOOTH

ENTER

BLUETOOTH

Notes

14 En

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

Once pairing has been completed, connecting a Bluetooth

will be easy the next time.

■ Connecting from the Bluetooth device

1 In the Bluetooth settings of the Bluetooth

device, turn Bluetooth on.

2 From the Bluetooth connection list of the

Bluetooth device, choose this unit (R-S202

Yamaha or R-S202D Yamaha).

The Bluetooth connection will be established, and the

front panel display of this unit will indicate

“CONNECTED”.

Bluetooth

connections c

annot be established from the

Bluetooth

device when this unit is in standby.

y

You can use the Bluetooth control buttons on the remote control

to control playback (see page 7).

If any of the following operations are performed while a

Bluetooth connection is being used, the Bluetooth

connection will be disconnected.

– Switch the audio source other than Bluetooth.

– Press A (power) to set this unit to standby mode.

– Turn off the Bluetooth setting of the Bluetooth device.

Connecting an already-paired

device via Bluetooth

Note

Disconnecting a Bluetooth

connection

English

15 En

You can tune in to a radio station by specifying its frequency or selecting from registered radio stations.

• The radio frequencies differ depending on the country or region where this unit is being used. Front panel display illustrations shown

in this section are based on Europe model.

• Only for Asia and General models:

Be sure to set the tuner frequency step according to the frequency spacing in your area before you tune in to a radio station (see page 30).

1 Press TUNER to select the tuner as the input

source.

2 Press BAND to select the FM/AM band.

3 Press and hold TUNING jj / ii to begin

tuning.

Press ii to tune in to a higher frequency.

Press jj to tune in to a lower frequency.

When this unit tunes in to a station, the TUNED

indicator lights up on the front panel display.

If the tuning search does not stop at the desired station because

the station signals are weak, press TUNING jj / ii repeatedly to

tune in to the desired station.

y

You can also use the buttons on the front panel if they have the

same or similar names as those on the remote control.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM band reception mode to monaural

mode to improve reception.

Front panel

Press FM MODE, and then make sure the ST indicator is

turned off (see page 4).

Remote control

Enter FM MODE from the Option menu to select MONO

(monaural mode) (see page 30).

You can register up to 40 radio stations as presets. Once

you have registered stations, you can easily tune in to

them by recalling the presets. You can automatically

register FM stations that have strong signals. If the FM

stations you want to store have weak signals, you can

register them manually (see page 16).

■ Presetting stations automatically

(Only for FM stations)

• If a station is registered to a preset number that already has a

station registered to it, the previously registered station is

overwritten.

• Only for Europe model:

Only Radio Data System broadcasting stations can be preset

automatically.

y

FM stations registered as presets using the automatic preset

registration feature will be heard in stereo.

FM/AM TUNING (R-S202)

Notes

Note

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

MEMORY

INFO

BAND

LINE 2 LINE 3

TUNING jj / ii

TUNER

BAND

Using preset functions

Notes

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

TREBLE

SPEAKERS

R

BASS

MENU

DIMMER

MUTE

VOLUME

BALANCE

BLUETOOTH

ENTER

MEMORY

INFO

BAND

LINE 2 LINE 3

B

A

BLUETOOTH

ENTER

PRESET j / i

TUNER

 /  / 

ENTER

MENU

BAND

16 En

FM/AM TUNING (R-S202)

1 Press TUNER to select the tuner as the input

source.

2 Press BAND to select the FM band.

3 Press MENU to enter the Option menu.

The Option menu for TUNER is displayed (see

page 30).

4 Press  /  to select “AUTO PRESET”, and

then press ENTER.

This unit starts scanning the FM band about

3 seconds later from the lowest frequency upwards.

y

• Before scanning begins, you can specify the first preset

number to be used by pressing PRESET j / i or  / .

• To cancel scanning, press .

When a station to preset is found, information is

displayed on the front panel display as shown in the

illustration above.

When scanning is complete, “FINISH” is displayed,

and then the display returns to the Option menu.

To return the display to the original state, press

MENU.

■ Presetting stations manually

You can manually register the desired radio stations.

1 Tune in to the desired FM/AM station.

See page 15 for tuning instructions.

2 Press MEMORY.

“MANUAL PRESET” is displayed briefly on the

front panel display, and then the preset number to

which the station will be registered is displayed.

y

By holding down MEMORY for more than 2 seconds, you

can skip the following steps and automatically register the

selected station to an empty preset number (i.e., the preset

number following the last preset number used).

3 Press PRESET j / i to select the preset

number to which the station will be

registered.

When you select a preset number to which no station

is registered, “EMPTY” is displayed. When you

select a preset number to which a station has already

been registered, the frequency of the station is

displayed.

4 Press MEMORY.

When registration is complete, the display returns to

the original state.

y

• To cancel registration, switch input or band or do not perform

any operations for about 30 seconds.

• You can also preset stations manually by pressing buttons on

the front panel with the same names as remote control.

Preset number Frequency

SLEEP

LINE 1

CD TUNER

TUNING

PRESET

TREBLE

MEMORY

INFO

BAND

LINE 2 LINE 3

A

PRESET j / i

MEMORY

Preset number

La pagina sta caricando ...

Yamaha R-S202 Manuale del proprietario

Questo manuale è adatto anche per

Yamaha R-S202 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti