Sony DCR-TRV50 Manuale del proprietario

3-075-396-21 (1)

Network Function

Operating

Instructions

2

On trademarks

•“Memory Stick” and are registered trademarks of Sony Corporation.

•The BLUETOOTH trademarks are owned by their proprietor and used by Sony

Corporation under license.

•NetFront by Access Co., Ltd. is adopted for the Internet function of this product.

NetFront is a registered trademark of Access Co., Ltd in Japan.

•Portions of the supplied software are based partially on the work of the Independent

JPEG Group.

All other product names mentioned herein may be the trademarks or registered

trademarks of their respective companies. Furthermore, “™” and “®” are not

mentioned in each case in this manual.

No compensation for your recordings

Any recording contents or downloaded files cannot be compensated for being lost due

to redording/playback malfunction or storage media problems.

Precautions

•Before using the network function, make sure to set the clock on the camcorder. For

details, refer to the operating instructions of the camcorder. If you use the network

function without setting the clock, you may not be able to send/receive e-mail or view

a web page.

•Do not remove the battery pack or disconnect the AC power adaptor while operating

in NETWORK mode. The setup for the NETWORK mode may be lost. Also, exit the

NETWORK mode when setting the POWER switch to OFF (CHG) or switching the

mode. These are to prevent the NETWORK mode setup from being lost.

•It is recommended that you make backup copies of your email messages and your

network preferences. These may be lost from time to time due to memory corruption.

To save the network preferences, write them down on paper, or use “Setup memo,”

described (p. 106). Also, this data may be lost when the camcorder is repaired by

services.

•The reset button cannot reset the network preferences.

Note on network operation when using the battery pack

When the remaining battery time is insufficient in NETWORK mode, use the AC power

adaptor or replace the battery pack with a fully charged battery pack. Before connecting

the AC power adaptor or replacing the battery pack, be sure to exit the NETWORK

mode.

Note on the network function

The network function is only available in the following countries or areas:

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Luxembourg,

Netherlands, Norway, Portugal, Sweden, Switzerland, United Kingdom, and Spain. (As

investigated by Sony Corporation on 1. 8. 2001)

When using the camcorder in a country or area not described above, the network

function is available only in the country or area where you purchased the camcorder.

3

Introduction

Table of contents

Introduction

The network function on the camcorder... 4

Basic operations in the NETWORK mode

.................................................................. 6

How to use the Network Menu .......... 6

How to hold your camcorder when

operating in the NETWORK

mode ................................................ 7

How to use the stylus .......................... 8

How to input characters ...................... 9

Character input display ..................... 11

The available characters list .............. 12

Character input setting ...................... 17

Preparation

Using the NETWORK functions ..............18

Overview of the Bluetooth wireless

technology ............................................19

Registering a Bluetooth device ......... 20

Using your Modem Adaptor with

Bluetooth Function ...................... 20

When the registration has failed ...... 24

Displaying information on your

camcorder ..................................... 24

Radio wave indication ....................... 26

Selecting other Bluetooth devices

from the list .................................. 26

Deleting a registered Bluetooth

device from the list ...................... 26

Customer registration ................................28

DI customer registration.................... 28

About the Login name (ID) and

password ...................................... 28

Registration for Album on the Web ......... 29

Internet service provider ........................... 30

Registration for “So-net” ........................... 31

Setting network preferences ..................... 32

Entering your Login name (ID) and

password ...................................... 32

Setting your provider preferences ... 34

Network Operation

Making your Album on the Web ............. 43

Uploading images to your Album on

the Web ......................................... 43

Viewing or editing your Album on

the Web ......................................... 50

Deleting images from your album ... 55

Finishing viewing or editing the

album ............................................ 55

Using email..................................................56

Sending email...................................... 56

Using the address book ..................... 67

Receiving email................................... 73

Deleting unnecessary email .............. 78

Viewing web pages ....................................80

Viewing web pages ............................ 80

How to use the menu bar on the

browser ......................................... 82

Storing the web page into a

“Memory Stick” – Page Memo .. 88

Shutting down the browser .............. 93

Additional Information

File storage destinations and file names

................................................................ 94

Troubleshooting..........................................95

Trouble accessing the Internet .......... 95

Trouble with email ............................. 96

Trouble viewing web pages .............. 97

Troubles about the Album on the

Web ................................................ 98

Adjusting the LCD screen

(CALIBRATION) ......................... 98

Specifications...............................................99

Messages ....................................................100

General ............................................... 100

Album on the Web ........................... 101

Email................................................... 101

Browser .............................................. 102

Album error codes .................................... 103

Glossary ..................................................... 104

Setup memo............................................... 106

4

Congratulations on your purchase of this Sony Handycam. This Handycam can access

to the Internet through your provider using a dial-up networking connection with a

Bluetooth device. You can view web pages, receive email, and send email with images

recorded on your camcorder attached. “Album on the Web” is your own private

Internet-based photo album. The communication system is Bluetooth Ver.1.1 and its

compatible Bluetooth profiles are the “Generic Access Profile” and the “Dial-up

Networking Profiles”.

– Introduction –

The network function on the camcorder

Easy access to

the Internet

You can view a web page

via the Internet.

You can send or receive email

anytime, and attach images to

email messages.

Send/receive your emails

5

Introduction

The network function on the camcorder

Making your album

on the Web

You can upload images to

your album, and view or

edit your album.

Set the camcorder’s clock setting before using the Network functions. (The default setting is OFF.)

If you do not set the clock setting, you cannot send and receive emails or view web pages.

You also have to set up your camcorder and the peripheral device, and complete required

registrations (DI customer registration, etc.).

For more information, see the supplied leaflet “Start Here!”.

“DI” in “DI customer registration” stands for “Digital Imaging”.

Using the “So-net” option, you can

easily set the required Internet and

email preferences. For details on

“So-net,” see “Using the

recommended provider (So-net)”

(p. 30), or the supplied leaflet “Start

Here!”.

Easy network

preferences (So-net)

6

This section describes basic control ways to operate your camcorder, those which are

used for network operations.

How to use the Network Menu

To access the Network Menu, refer to “Accessing the network” in the operating

instructions supplied with your camcorder.

[a]: Send and receive email. For details, see “Using email” (p. 56).

[b]: View a web page through the Internet. For details, see “Viewing web pages”

(p. 80).

[c]: You have to make various settings using this menu before using the network

function. For details, see “Setting network preferences” (p. 32).

[d]: Exit the NETWORK mode.

[e]: Upload images to your Album on the Web and post the images on the Internet. For

details, see “Making your Album on the Web” (p. 43).

The actual screens may differ slightly from the illustrations in this network

function operating instructions.

Basic operations in the NETWORK mode

[a]

[b]

[c]

[d]

[e]

7

Introduction

How to hold your camcorder when operating in the NETWORK

mode

When operating in the NETWORK mode, you can turn the LCD panel over and move it

back to your camcorder with the LCD screen facing over to use the stylus (for touch

panel operation, supplied).

1 Turn the LCD panel over and move it back to your camcorder with the LCD

screen facing over.

2 Hold your camcorder as illustrated below.

The way to hold and operate your camcorder varies depending on the model.

For detail, refer to the “Operating Instructions” supplied with your camcorder.

Basic operations in the NETWORK mode

8

How to use the stylus

The buttons required for operating your camcorder are displayed on the LCD screen.

Operate by pressing the buttons on the screen directly but lightly with the stylus

provided. In this manual, pressing the buttons in this way using the stylus is referred to

as “tapping”.

Tap the desired button on the screen with the stylus.

The selected button turns orange.

,

Notes

•Do not tap them with sharp-pointed objects other than the stylus supplied.

•Do not tap the LCD screen too hard.

•Do not touch the LCD screen with wet hands.

•When the LCD screen gets dirty, use the supplied cleaning cloth.

•You cannot drag icons, like on a computer, by touching and sliding across your

camcorder screen with the stylus.

•Refer to the operating instructions supplied with your camcorder for the stylus

storage location. To avoid losing the stylus, we recommend that you return it to the

storage location after use.

Basic operations in the NETWORK mode

9

Introduction

How to input characters

You have to frequently enter characters, such as email addresses, or web pages

addresses (URL), to use the network function. This section describes how to input

characters.

1

(1) Open the Network Menu.

For details on how to open the Network Menu, refer to “Accessing the

network” in the operating instructions supplied with your camcorder.

(2) Tap [

Mail].

The Send screen appears.

,

(3) Tap [To].

,

(4) Tap [ New].

The character input screen appears.

,

Basic operations in the NETWORK mode

10

Basic operations in the NETWORK mode

2 Selecting the character type

Tap [abcy123], then tap the desired character type.

abc: When inputting alphabetical characters.

123: When inputting numerical characters.

When you selected abc When you selected 123

3 Inputting characters

(1) Tap the character you want to input.

(2) After you input the characters, tap [Enter].

The screen which is displayed before you display the character input screen

appears.

11

Introduction

Basic operations in the NETWORK mode

1 [a/A] button

[a/A] button is displayed when you input alphabetical characters.

You can switch between upper case and lower case.

2 [abcy123] button

A list box appears when you tap the [abcy123] button. Tap the desired

type of letter from the list box.

3 Input byte number/maximum byte number

4 Preferences

You can change the keyboard type for alphabet input.

5 Text area

You can scroll up or down the display by tapping v or V.

6 [Space] button

A space is entered.

7 [Back Space] button

The letter right before the cursor is deleted. If you tap the button for

about three seconds, all the characters before the cursor are deleted.

8

button

The cursor moves to a new line.

9 [Enter] button

Tap this button to decide or close the input screen.

1

2

6

78

9

5

4

3

Character input display

12

Basic operations in the NETWORK mode

The available characters list

When selecting [abc]

Alphabetical characters

The alphabet keyboard has 2 types (PC Style and Alphabetical order). The default

setting is PC arrangement. You can change the keyboard setting in . Refer to page 17

for more information.

(PC Style) (Alphabetical order)

Key Character

` ´ ˆ

* a: à t á t â t a t... A: À t Á t Â t A t...

e: è t é t ê t e t... E: È t É t Ê t E t...

i: ì t í t î t i t... I: Ì t Í t Î t I t...

o: ò t ó t ô t o t... O: Ò t Ó t Ô t O t...

u: ù t ú t û t u t... U: Ù t Ú t Û t U t...

y:

´y

t y t... Y:

´

Y

t Y t...

¨ ˜

* a: ä t ã t a t... A: Ä t Ã t A t...

e: ë t e t... E: Ë t E t...

i: ï t i t... I: Ï t I t...

n: ñ t n t... N: Ñ t N t...

o: ö t õ t o t... O: Ö t Õ t O t...

u: ü t u t... U: Ü t U t...

y: ÿ t y t...

’ ”

’ t ” t ’ t ...

? ¿

? t ¿ t ? t ...

! ¡

! t ¡ t ! t ...

ç

Ç

ß

ç t Ç t ß t ç t...

. ,

. t , t . t ...

/ \

/ t \ t / t ...

abcdefghi jklm

nopqrs tuvwxy z

ABCDEFGHI J KLM

NOPQR S TUVWXY Z

* You can input the alphabet characters with accent symbols. When you input the

characters, tap

` ´ ˆ

or

¨ ˜

after inputting a, e, i, n, o, u, y, A, E, I, N, O, U or Y.

~ – _

@

:

Symbol characters

The symbol characters below are inputted by single tapping:

The green keys input the symbol characters.

The symbol characters change as follows:

13

Introduction

To switch between upper and lower case alphabet letters

Tap [a/A] to change the alphabetical keyboard, then enter characters.

To delete a character

Move the cursor with the stylus to the right of the character at which you want to

delete, tap [Back space]. The character at the left of the cursor is deleted.

To add a character

Move the cursor with the stylus to the position at which you want to add a character,

then input characters.

To start a new line

Tap [ ].

Basic operations in the NETWORK mode

When selecting [123]

Symbol characters

(Numerical order)

123+( )$

C

\%

456– []&ˆ | ˜

789/{}`”’ ,

* 0#=<> . : ; _

14

Basic operations in the NETWORK mode

E.g., Enter “Hello” into the Subject item on the Send screen

1

(1) Open the Network Menu.

For details on how to open the Network Menu, refer to “Accessing the

network” in the operating instructions supplied with your camcorder.

(2) Tap [

Mail].

The Send screen appears.

,

2 Entering the subject of a message

(1) Tap [Subject].

(2) Tap [

New].

The character input screen appears.

,

15

Introduction

Basic operations in the NETWORK mode

3

(1) Tap [abcy123], then tap [abc].

(2) Tap [a/A] to be able to enter upper-case letters.

,

(3) Tap [H].

“H” is entered.

,

(4) Tap [a/A] to be able to enter lower-case letters.

,

16

Basic operations in the NETWORK mode

(5) Tap [e].

“e” is entered.

,

(6) Tap [l], [l] and [o].

“llo” is entered.

,

(7) Tap [Enter].

“Hello” is entered and the Send screen appears again.

,

17

Introduction

Basic operations in the NETWORK mode

Character input setting

Keyboard

You can change the display of the alphabet, PC arrangement keyboard or ABC

arrangement keyboard into a setup you want when you input characters.

1 Tap in the character input screen.

,

2 Tap the desired setting.

You can set as the following two displays when [abcy123] is set as [abc].

(PC Style is the default setting.)

– PC Style (PC arrangement keyboard)

– Alphabetical order (ABC arrangement keyboard)

To switch the setting, tap on the upper-right LCD screen.

Alphabetical orderPC Style

18

There are three Network functions, namely Album on the Web, email, and browser. To

use the Album on the Web, you need to complete customer registration.

“So-net” is charged service.

For more information, see the supplied leaflet “Start Here!”.

To fully use the function in the NETWORK mode, you have to complete the following

registrations with your computer (1~3) and setup tasks via your camcorder (4, 5):

1 DI customer registration (p. 28)

2 Registration for “So-net” * (p. 31)

3 Registration for Album on the Web (p. 29)

4 Network Setup (p. 32)

5 Registering a Bluetooth device (p. 20)

* Registration for “So-net” is not necessary to use the other provider.

URL for Registration:

“http://www.sony.co.uk/imaging/”

– Preparation –

Using the NETWORK functions

Preparation

19

Overview of the Bluetooth wireless

technology

What is the Bluetooth wireless technology?

The Bluetooth wireless technology allows communication between various Bluetooth

devices without using cables. Devices which can use this technology include PCs,

computer peripheral devices, PDAs, and mobile phones. This omnidirectional

communication system enables communication even if the Bluetooth device is in a bag

or having obstacles between the devices.

Also, the Bluetooth wireless technology has advanced security functions, such as

scrambled frequencies and data encryption.

Authentication

The authentication routine can block unspecified users’ access to this network. When

attempting communication with an unregistered Bluetooth device, the devices must

first be registered with each other by entering a common passkey to each device. When

connecting with a previously registered Bluetooth device, communication starts

without entering the passkey.

20

Registering a Bluetooth device

This section describes making a registration of a Bluetooth device. Here we describe the

procedure for registering the Sony Modem Adaptor with Bluetooth Function. Once the

registration is completed, your camcorder can connect to your Bluetooth device without

reregistering the device. You can register up to three Bluetooth devices. Also, refer to

the operating instructions supplied with your Bluetooth device.

For more information about Bluetooth devices compatible with your camcorder, access

the following URL: “http://www.sony-imaging.com/support/”

Notes

•When using Sony BTA-NW1/BTA-NW1A Modem Adaptor with Bluetooth Function,

place it at a location that has no obstacles between your camcorder and the device.

The distance between the devices must be within 10 m (33 feet).

•The connection may be interrupted depending on the communication conditions.

Using your Modem Adaptor with Bluetooth Function

1 Preparing the Modem Adaptor with Bluetooth Function

Set the Modem Adaptor with Bluetooth Function to connection standby (BONDING).

For details, refer to the operating instructions supplied with your Modem Adaptor with

Bluetooth Function.

Overview of the Bluetooth wireless technology

La pagina sta caricando ...

Sony DCR-TRV50 Manuale del proprietario

Questo manuale è adatto anche per

Sony DCR-TRV50 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti