ASROCK 775I65GV Manuale del proprietario

11

1

ASRock 775i65GV Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published July 2004

22

2

ASRock 775i65GV Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 System Panel Header (PANEL1)

2 775-Pin CPU Socket 17 Infrared Module Header (IR1)

3 North Bridge Controller 18 Clear CMOS Jumper (CLRCMOS0)

4 CPU Fan Connector (CPU_FAN1) 19 Floppy Connector (FLOPPY1)

5 184-pin DDR DIMM Slots (DDR1- 2, Dual Channel) 20 AMR Slot (AMR1)

6 ATX Power Connector (ATXPWR1) 21 Internal Audio Connector: CD1 (Black)

7 Primary IDE Connector (IDE1, Blue) 22 Internal Audio Connector: AUX1 (White)

8 Secondary IDE Connector (IDE2, Black) 23 PCI Slots (PCI1- 3)

9 ASRock Graphics Interface Slot (1.5V_AGP1) 24 JR1 Jumper / JL1 Jumper

10 South Bridge Controller 25 Front Panel Audio Header (AUDIO1)

11 Secondary Serial ATA Connector (SATA2) 26 COM Port Header (COM1)

12 Primary Serial ATA Connector (SATA1) 27 Shared USB 2.0 Header (USB4_5, Blue)

13 Chassis Speaker Header (SPEAKER 1) 28 BIOS FWH Chip

14 Chassis Fan Connector (CHA_FAN1) 29 FSB Select Jumper (FSB1)

15 USB 2.0 Header (USB67, Blue) 30 ATX 12V Connector (ATX12V1)

33

3

ASRock 775i65GV Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 VGA Port

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 Shared USB 2.0 Ports (USB45)

44

4

ASRock 775i65GV Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock 775i65GV motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website as

well. ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock 775i65GV Motherboard

(Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm)

ASRock 775i65GV Quick Installation Guide

ASRock 775i65GV Support CD (including LGA 775 CPU Installation Live Demo)

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock I/O Plus

TM

Shield

One COM Port Bracket

One ASRock MR Card (Optional)

55

5

ASRock 775i65GV Motherboard

EnglishEnglish

English

1.2 Specifications1.2 Specifications

1.2 Specifications

Platform: Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm

CPU: 775-Pin Socket

supporting Intel

®

Pentium

®

4 / Celeron

®

processor (in 775-land

LGA package)

Chipsets: North Bridge:

Intel

®

865GV chipset, FSB @ 800 / 533 MHz,

supports Hyper-Threading Technology (see CAUTION 1)

South Bridge:

Intel

®

ICH5, supports SATA 1.5Gb/s

Memory: 2 DDR DIMM slots: DDR1 and DDR2

supports PC3200 (DDR400) / PC2700 (DDR333) /

PC2100 (DDR266), Max. 2GB (see CAUTION 2)

Dual Channel Memory Technology support

(see CAUTION 3)

IDE: IDE1: ATA 100 / Ultra DMA Mode 5

IDE2: ATA 100 / Ultra DMA Mode 5

Supports up to 4 IDE devices

Serial ATA: Supports up to 2 SATA devices at 1.5Gb/s data transfer rate.

(No Support for “RAID” and “Hot Plug” functions)

Floppy Port: Supports up to 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor:CPU temperature sensing

Motherboard temperature sensing

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 4)

CPU fan tachometer

Chassis fan tachometer

Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 3 PCI slots with PCI Specification 2.2 (see CAUTION 5)

AMR slot: 1 slot, supports ASRock MR card (Optional)

AGI slot: 1 AGI [ASRock Graphics Interface] slot (see CAUTION 6)

USB 2.0: 8 USB 2.0 ports:

includes 6 default USB 2.0 ports on the rear panel,

plus one header to support 2 additional USB 2.0 ports

(see CAUTION 7)

ASRock I/O Plus

TM

: 1 PS/2 mouse port, 1 PS/2 keyboard port,

1 VGA port, 1 parallel port: ECP/EPP support,

6 default USB 2.0 ports,

1 RJ-45 port,

Audio Jack: Line In / Line Out / Microphone

66

6

ASRock 775i65GV Motherboard

EnglishEnglish

English

COM Port: 1 COM Port Header to support a COM port module

BIOS: AMI legal BIOS, Supports “Plug and Play”,

ACPI 1.1 compliance wake up events,

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 8)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 27

of “User Manual” in the Support CD.

2. Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency Memory Support Frequency

800 DDR266, DDR320

*, DDR400

533 DDR266, DDR333

400 DDR266

* When you use an FSB800-CPU on this motherboard, it will run at

DDR320 if you adopt a DDR333 memory module.

3. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 12 for proper installation.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. Because the installed AMR card will occupy the same external connecting

position with the PCI card that are installed in “PCI3” slot, you will not be

able to install any PCI card in “PCI3” slot if an AMR card has already been

installed in the AMR slot.

6. The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compatible

AGP VGA cards, please refer to the “Supported AGP VGA Cards List” on

page 7 and page 8. For the proper installation of AGP VGA card, please

refer to the installation guide on page 13.

7. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 / 2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/

ME. Please refer to Microsoft

®

official document at

http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx

8. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

77

7

ASRock 775i65GV Motherboard

1.31.3

1.3

Supported AGP VGA Cards ListSupported AGP VGA Cards List

Supported AGP VGA Cards List

(for Windows 2000/Windows XP)

I. AGP 4X

Graphics Chip Model Name

Vendor

n-VIDIA ASUS AGP-V7100

ASUS AGP-V7100PRO

ASUS AGP-V7100 MAGIC / 32M

ASUS AGP-V7700Ti

ASUS AGP-V8170DDR

ASUS AGP-V8170SE / LP

ASUS AGP-V8200 T2

ASUS AGP-V8200 T5

ASUS AGP-V8440

ASUS AGP-V8460 Ultra

GAINWARD- GF3-TI500/64M

GAINWARD- GF3-TI500/128M

Inno3D GeForce2 MX400

Leadtek WinFast A170 TH

Leadtek WinFast A170 DDR

Leadtek WinFast A250LE TD

Leadtek WinFast GeForce2 MX MX64

Leadtek WinFast GeForce2 H MX400

MSI- GF4-MX440SE

PROLINK GF4-MX440

SPARKLE GF4-MX440

ATI Gigabyte GV-AP64D

Gigabyte GV-AP64D-H

Gigabyte GV-AR64S-H

POWERCOLOR RADEON 9000

POWERCOLOR RADEON 9100

TRANSCEND TS64MVDR7

SiS SYNNEX GCM-SiS315EA32

For the latest updates of the supported AGP VGA cards list, please visit

ASRock website for details.

ASRock website: http://www.asrock.com/support/index.htm

EnglishEnglish

English

88

8

ASRock 775i65GV Motherboard

II. AGP 8X

Graphics Chip Model Name

Vendor

n-VIDIA ALBATRON GF4-MX440 64M

AOPEN Aeolus FX5600S-DV128

AOPEN Aeolus FX5200-V128

ASUS AGP-V9180

ASUS AGP-V9280 VIEDO SUITE

ASUS AGP-V9520 MAGIC/T

ASUS V9900

ASUS V9900 ULTRA

ELSA-GLADIC 518

ELSA-GLADIC 518 P

Inno3D GeForce FX5600

LEADTEK A280 LE

LEADTEK A340TDH

MSI Ti4800SE-VTD8X

PALIT GF4 MX440 8X 64MB

PROLINK GeForceFX5900

PROLINK GF4-TI4200

SPARKLE GF4-MX440-8X

ATI CLUB3D ATI R9800

Gigabyte GV R9000 PRO

Gigabyte RADEON 9500

Gigabyte RADEON 9700 PRO

POWER COLOR 9200

SAPHIRE RADEON 9200-128MB

SiS POWER COLOR XABRE600

For the latest updates of the supported AGP VGA cards list, please visit

ASRock website for details.

ASRock website:

http://www.asrock.com/support/index.htm

EnglishEnglish

English

99

9

ASRock 775i65GV Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-Pin CPU,

please follow the steps below.

Before you insert the 775-Pin CPU into the socket, please check if the

CPU surface is unclean or if there is any bent pin on the socket. Do

not force to insert the CPU into the socket if above situation is found.

Otherwise, the CPU will be seriously damaged.

EnglishEnglish

English

775-Pin Socket Overview

1010

10

ASRock 775i65GV Motherboard

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-Pin CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin CPU

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

EnglishEnglish

English

1111

11

ASRock 775i65GV Motherboard

It is recommended to use the cap tab to handle and avoid kicking off

the PnP cap.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of

your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-Pin CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 10, No. 4).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

EnglishEnglish

English

1212

12

ASRock 775i65GV Motherboard

2.32.3

2.3

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

775i65GV motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install two identical (the same brand, speed, size and chip-

type) memory modules in the DDR DIMM slots to activate Dual Channel Memory

Technology. Otherwise, it will operate at single channel mode.

If you install only one memory module or two non-identical memory

modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

EnglishEnglish

English

1313

13

ASRock 775i65GV Motherboard

2.4 Expansion Slots (PCI, AMR, and AGI Slots)2.4 Expansion Slots (PCI, AMR, and AGI Slots)

2.4 Expansion Slots (PCI, AMR, and AGI Slots)

There are 3 PCI slots, 1 AMR slot, and 1 AGI slot on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

Because the installed AMR card will occupy the same external

connecting position with the PCI card installed in “PCI3” slot, you will

no be able to install any PCI card in “PCI3” slot if an AMR card has

already been installed in the AMR slot.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

AGI slot: The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compat-

ible AGP VGA cards, please refer to the “Supported AGP VGA Cards List”

on page 7 and page 8.

To install the system with an add-on AGP VGA card, you must make

sure to install the driver of add-on AGP VGA card before you install

the onboard VGA driver. If the onboard VGA driver has already been

installed before you install the add-on AGP VGA card, the system will

automatically set the onboard VGA as the primary graphics adapter. In

that case, if you want to install the add-on AGP VGA card, you need

to remove the onboard VGA driver first, and then install the add-on

AGP VGA card and its driver. For the detailed instruction, please refer

to the documents in the Support CD, “AGI Slot Installation Guide (for

Windows 2000)” and “AGI Slot Installation Guide (for Windows XP)”,

which are located in the folder at the following path:

..\ Easy Dual Monitor

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

EnglishEnglish

English

1414

14

ASRock 775i65GV Motherboard

Short Open

2.5 Easy Dual Monitor Feature2.5 Easy Dual Monitor Feature

2.5 Easy Dual Monitor Feature

Thanks to ASRock patented AGI8X Technology, this motherboard supports Easy

Dual Monitor upgrade. With the internal onboard VGA and the external add-on AGP

VGA card, you can easily enjoy the benefits of Dual Monitor feature. For the

detailed instruction, please refer to the document at the following path in the

Support CD: ..\ Easy Dual Monitor

2.6 Jumpers Setup2.6 Jumpers Setup

2.6 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “SHORT”. If no jumper cap

is placed on the pins, the jumper is “OPEN”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “SHORT” when jumper cap

is placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

FSB Select Jumper

(see p.2 No. 29)

Note: The default setting of the FSB Select jumper is “NORMAL” (short pin1, pin2).

For the system’s stability, please keep the default setting.

JR1 / JL1 Jumpers

(see p.2 No. 24)

Note:If JR1 and JL1 Jumpers are short, both the front panel and the rear panel

audio connectors can work.

NORMAL

TEST

EnglishEnglish

English

1515

15

ASRock 775i65GV Motherboard

Clear CMOS

(CLRCMOS0)

(see p.2 No. 18)

Note:CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short the Clear CMOS

jumper for 5 seconds. After shorting the Clear CMOS jumper, please remove

the jumper cap. However, please do not clear the CMOS right after you update

the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,

you must boot up the system first, and then shut it down before you do the

clear-CMOS action.

2-pin jumper

EnglishEnglish

English

1616

16

ASRock 775i65GV Motherboard

2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 19)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.2 No. 7) (39-pin IDE2, see p.2 No. 8)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 No. 12) connectors support SATA data

(SATA2: see p.2 No. 11) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-Conductor ATA 66/100 cable

the red-striped side to Pin1

SATA2

SATA1

EnglishEnglish

English

1717

17

ASRock 775i65GV Motherboard

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock I/O Plus

TM

accommo-

(9-pin USB67) dates 6 default USB 2.0 ports. If

(see p.2 No. 15) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Shared USB 2.0 Header This USB4_5 connector is shared

(9-pin USB4_5) with the USB 2.0 ports 4,5 on

(see p.2 No. 27) ASRock I/O Plus

TM

. When using

the front panel USB ports by

attaching the front panel USB

cable to this connector

(USB4_5), the USB ports 4,5 on

ASRock I/O Plus

TM

will not be able

to function.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 17) and receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.2 No. 21) from sound sources such as

(AUX1: see p.2 No. 22) a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 25) convenient connection and

control of audio devices.

connect to the

power supply

connect to the SATA

HDD power connector

CD1 AUX1

EnglishEnglish

English

1818

18

ASRock 775i65GV Motherboard

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 16) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 13)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 14) match the black wire to the

ground pin.

CPU Fan Connector You may connect either a 3-pin

(4-pin CPU_FAN1) or a 4-pin CPU fan cable to this

(see p.2 No. 4) connector, then match the black

wire to the ground pin.

Note: If you use a 3-pin CPU fan cable, insert it to the connector by aligning it with the pins

“GND”, “+12V”, and “CPU_FAN_SPEED”.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 7)

COM Port Header This COM port header is used

(9-pin COM1) to support a COM port module.

(see p.2 No. 23)

ATX 12V Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 30) ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

EnglishEnglish

English

1919

19

ASRock 775i65GV Motherboard

2.82.8

2.8

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA

(SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

Before you install OS into the SATA hard disk, you need to check and

ensure the configuration of the OnBoard IDE Operate Mode option in

BIOS setup is correct according to the condition of your system. For

the configuration details, please refer to the instruction on page 27 of

“User Manual” in the Support CD.

3. BIOS Information3. BIOS Information

3. BIOS Information

The BIOS Setup Utility is stored in the BIOS FWH chip. When you start up the

computer, please press <F2> during the Power-On-Self-Test (POST) to enter the

BIOS Setup Utility; otherwise, POST continues with its test routines. If you wish to

enter the BIOS Setup Utility after POST, please resume the system by pressing <Ctl>

+ <Alt> + <Delete>, or pressing the reset button on the system chassis. For the

detailed information about the BIOS Setup Utility, please refer to the User Manual

(PDF file) contained in the Support CD.

EnglishEnglish

English

2020

20

ASRock 775i65GV Motherboard

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

“PC-DIY Live Demo”

ASRock presents you a multimedia PC-DIY live demo, which shows you a

step-by-step guide to install your own PC system. To see this demo program,

you can run Microsoft

®

Media Player

®

to play the file, which can be found

through the following path:

..\ MPEGAV \ AVSEQ01.DAT

“LGA 775 CPU Installation Live Demo”

This motherboard is equipped with Intel LGA 775 socket, which is a new CPU

socket interface that Intel has released. Since it has several tiny pins, whcih

are easily to be damaged by improper handling, ASRock sincerely presents

you a clear installation guide through this “LGA 775 CPU Installation Live

Demo”. We hope you may check this live demo program before you start the

installation of LGA 775 CPU in order to reduce the risks of CPU and

motherboard damages caused by any improper handling. To see this Live

Demo, you can run Microsoft

®

Media Player

®

to play the file. You may find this

Live Demo in the motherboard’s Support CD through the following path:

..\ MPEGAV \ LGA775INST.DAT

EnglishEnglish

English

La pagina sta caricando ...

ASROCK 775I65GV Manuale del proprietario

ASROCK 775I65GV Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti