ASROCK CONROE865GV Manuale del proprietario

11

1

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published August 2006

22

2

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 Infrared Module Header (IR1)

2 ATX 12V Connector (ATX12V1) 17 Clear CMOS Jumper (CLRCMOS0)

3 775-Pin CPU Socket 18 USB 2.0 Header (USB67, Blue)

4 North Bridge Controller 19 Floppy Connector (FLOPPY1)

5 CPU Fan Connector (CPU_FAN1) 20 COM Port Header (COM1)

6 184-pin DDR DIMM Slots (DDR1- 2, Dual Channel) 21 AMR Slot (AMR1)

7 Secondary IDE Connector (IDE2, Black) 22 Front Panel Audio Header (AUDIO1)

8 Primary IDE Connector (IDE1, Blue) 23 JR1 Jumper / JL1 Jumper

9 ASRock Graphics Interface Slot (1.5V_AGP1) 24 Internal Audio Connector: AUX1 (White)

10 South Bridge Controller 25 Internal Audio Connector: CD1 (Black)

11 Secondary Serial ATA Connector (SATA2) 26 PCI Slots (PCI1- 3)

12 Primary Serial ATA Connector (SATA1) 27 BIOS FWH Chip

13 Chassis Fan Connector (CHA_FAN1) 28 Shared USB 2.0 Header (USB4_5, Blue)

14 System Panel Header (PANEL1) 29 ATX 12V Connector (ATX12V1)

15 Chassis Speaker Header (SPEAKER 1)

33

3

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 VGA Port

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 Shared USB 2.0 Ports (USB45)

44

4

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock ConRoe865GV motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock ConRoe865GV Motherboard

(Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm)

ASRock ConRoe865GV Quick Installation Guide

ASRock ConRoe865GV Support CD

(including LGA 775 CPU Installation Live Demo)

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock I/O Plus

TM

Shield

One COM Port Bracket

One ASRock MR Card (Optional)

55

5

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm

CPU - LGA 775 for Intel

®

Core

TM

2 Duo / Pentium

®

XE / Pentium

®

D /

Pentium

®

4 / Celeron

®

D, supporting Conroe processors

(in 775-land LGA package) (see CAUTION 1)

- FSB 800/533 MHz

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset - Northbridge: Intel

®

865GV

- Southbridge: Intel

®

ICH5

Memory - Dual Channel DDR memory technology (see CAUTION 4)

- 2 x DDR DIMM slots

- Support DDR400/333/266 (see CAUTION 5)

- Max. capacity: 2GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 6)

- ASRock U-COP (see CAUTION 7)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 3 x PCI slots

- 1 x AGI slot (see CAUTION 8)

- 1 x AMR slot (see CAUTION 9)

Graphics - Integrated Intel

®

Extreme Graphics 2

- DirectX 8.0

- Max. shared memory 96MB

Audio - C-Media 9761A 5.1 channel audio CODEC

LAN - Realtek PCI LAN 8101L

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O ASRock I/O Plus

TM

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA Port

- 1 x Parallel Port (ECP/EPP Support)

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port

- Audio Jack: Line in/Front Speaker/Microphone

66

6

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

Connector - 2 x Serial ATA 1.5 Gb/s connectors

(No Support for RAID and “Hot Plug” functions)

- 2 x ATA100 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x COM port header

- 1 x IR header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- AUX in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports; 2 of them are

shared with USB45 ports on the I/O panel)

(see CAUTION 10)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

98SE / ME / 2000 / XP compliant

Certifications - FCC, CE, WHQL

77

7

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

CAUTION!

1. This motherboard supports FSB800-CPU. If you plan to adopt Core

TM

2

Duo CPU on this motherboard, you can only adopt Conroe 800 E4XXX

processors.

2. About the setting of “Hyper Threading Technology”, please check page 28

of “User Manual” in the support CD.

3. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 19 for details.

4. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 13 for proper installation.

5. Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency Memory Support Frequency

800 DDR266, DDR333

*, DDR400

533 DDR266, DDR333

* When you use an FSB800-CPU on this motherboard, it will run at

DDR320 if you adopt a DDR333 memory module.

6. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

7. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

8. The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compatible

AGP VGA cards, please refer to the “Supported AGP VGA Cards List” on

page 8 and page 9. For the proper installation of AGP VGA card, please

refer to the installation guide on page 14.

9. Because the installed AMR card will occupy the same external connecting

position with the PCI card that are installed in “PCI3” slot, you will not be

able to install any PCI card in “PCI3” slot if an AMR card has already been

installed in the AMR slot.

10. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP SP1 or SP2 / 2000 SP4. It may not work properly under Microsoft

®

Windows

®

98 / ME.

88

8

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

1.31.3

1.3

Supported AGP VGA Cards ListSupported AGP VGA Cards List

Supported AGP VGA Cards List

(for Windows

®

2000/Windows

®

XP)

I. AGP 4X

Graphics Chip Model Name Chipset Name

Vendor

NVIDIA ASUS V8170 GeForce MX440SE

Ennyah G2 MX400 GeForce 2 MX400

II. AGP 8X

Graphics Chip Model Name Chipset Name

Vendor

NVIDIA ASUS N6200 NVIDIA GeForce 6200A

ASUS N6200GE/TD/128M NVIDIA GeForce 6200

ASUS N6600LE/TD/256M NVIDIA GeForce 6600 LE

ASUS V9180 Magic GF4 MX 440 64M

ASUS V9400MAGIC GeForce 4 MX4000

ASUS V9520-X/128M GeForce FX 5200

ASUS V9560/TD GeForce FX5600

ASUS V9570/TD/256M GeForce FX5700

ASUS V9950ULTRA GeForce FX 5900 Ultra

ASUS V9999 Ultra/2DT 6800 Ultra 256M

Albatron AGP6600GT 6600GT

Albatron FX5600P Turbo GeForce FX 5600

Albatron MX-480E GeForce 4 MX440-8X

Aopen Aeolus Fx5200-DV 128 FX 5200 128M

CHAINTECH SA5900X NVIDIA GeForce 5900XT

ELSA GLADIC FX733 NVIDIA GeForce 5500

Ennyah GeForce FX5200 ULTRA GeForce FX 5200 Ultra

Gigabyte GV-N57L256D GeForce FX 5700 LE

Gigabyte GV-N66128DP GeForce 6600

Inno3D GeForce FX 5600 128MB NVIDIA GeForce FX 5600

Leadtek WinFast A340PRO/TD GeForce FX 5500

Leadtek WinFast A340TDH GeForce FX 5200

Leadtek WinFast A360TD GeForce FX 5600

Leadtek WinFast A400TDH GeForce 6800

Leadtek WinFast A6600 GT TDH GeForce 6600GT

MSI FX5700-TD128 GeForce FX 5700

MSI FX5700-VTD128 NVIDIA GeForce 5700

Prolink FX5900/128M FX5900

Prolink PV-N36AX FX 5700 LE 128MB

XFX 7800GS NVIDIA GeForce 7800GS

99

9

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

ATI ASUS A9800XT ATI Radeon 9800 XT

ELSA FALCOX 920FX Radeon 9200

GECUBE Radeon 9250/128M Radeon 9250

MSI RX 9200 SE-T128 Radeon 9200 SE

PowerColor Radeon 9200SE Radeon 9200SE

PowerColor RADEON 9250/128M Radeon 9250

* ATI 9600/9550 series and all Matrox series VGA cards are NOT supported with AGI.

For the latest updates of the supported AGP VGA cards list, please visit

ASRock website for details.

ASRock website: http://www.asrock.com/support/index.htm

1010

10

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-Pin CPU,

please follow the steps below.

Before you insert the 775-Pin CPU into the socket, please check if the

CPU surface is unclean or if there is any bent pin on the socket. Do

not force to insert the CPU into the socket if above situation is found.

Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

1111

11

ASRock ConRoe865GV Motherboard

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-Pin CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin CPU

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

EnglishEnglish

English

1212

12

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of

your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-Pin CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2, No. 5).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

1313

13

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

ConRoe865GV motherboard provides two 184-pin DDR (Double Data Rate) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install two identical (the same brand, speed, size and chip-

type) memory modules in the DDR DIMM slots to activate Dual Channel Memory

Technology. Otherwise, it will operate at single channel mode.

If you install only one memory module or two non-identical memory

modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1414

14

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI, AMR, and AGI Slots)2.4 Expansion Slots (PCI, AMR, and AGI Slots)

2.4 Expansion Slots (PCI, AMR, and AGI Slots)

There are 3 PCI slots, 1 AMR slot, and 1 AGI slot on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

Because the installed AMR card will occupy the same external

connecting position with the PCI card installed in “PCI3” slot, you will

no be able to install any PCI card in “PCI3” slot if an AMR card has

already been installed in the AMR slot.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

AGI slot: The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compat-

ible AGP VGA cards, please refer to the “Supported AGP VGA Cards List”

on page 8 and page 9.

To install the system with an add-on AGP VGA card, you must make

sure to install the driver of add-on AGP VGA card before you install

the onboard VGA driver. If the onboard VGA driver has already been

installed before you install the add-on AGP VGA card, the system will

automatically set the onboard VGA as the primary graphics adapter. In

that case, if you want to install the add-on AGP VGA card, you need

to remove the onboard VGA driver first, and then install the add-on

AGP VGA card and its driver. For the detailed instruction, please refer

to the documents in the Support CD, “AGI Slot Installation Guide (for

Windows 2000)” and “AGI Slot Installation Guide (for Windows XP)”,

which are located in the folder at the following path:

..\ Easy Dual Monitor

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1515

15

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

2.5 Easy Dual Monitor Feature2.5 Easy Dual Monitor Feature

2.5 Easy Dual Monitor Feature

Thanks to ASRock patented AGI8X Technology, this motherboard supports Easy

Dual Monitor upgrade. With the internal onboard VGA and the external add-on AGP

VGA card, you can easily enjoy the benefits of Dual Monitor feature. For the

detailed instruction, please refer to the document at the following path in the

Support CD: ..\ Easy Dual Monitor

2.6 Jumpers Setup2.6 Jumpers Setup

2.6 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note:To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1 / JL1 Jumpers

(see p.2 No. 23)

Note:If JR1 and JL1 Jumpers are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS0)

(see p.2 No. 17)

Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on

CLRCMOS0 for 5 seconds.

Short Open

2-pin jumper

1616

16

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 19)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.2 No. 8) (39-pin IDE2, see p.2 No. 7)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 No. 12) connectors support SATA data

(SATA2: see p.2 No. 11) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

(Optional) hard disk or the SATA connector

on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-Conductor ATA 66/100 cable

the red-striped side to Pin1

SATA2

SATA1

1717

17

ASRock ConRoe865GV Motherboard

connect to the

power supply

connect to the SATA

HDD power connector

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header Besides six default USB 2.0

(9-pin USB67) ports on the I/O panel, there are

(see p.2 No. 18) two USB 2.0 headers on this

motherboard. Each USB 2.0

header cansupport two USB

2.0 ports. The shared USB 2.0

header (USB4_5) is shared with

Shared USB 2.0 Header USB ports 45 on the I/O panel.

(9-pin USB4_5) When using the front panel USB

(see p.2 No. 28) ports by attaching the front panel

USB cable to USB4_5 header,

the USB ports 45 on the I/O panel

will not be able to function.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 16) and receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.2 No. 25) from sound sources such as

(AUX1: see p.2 No. 24) a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(8-pin AUDIO1) panel audio cable that allows

(see p.2 No. 22) convenient connection and

control of audio devices.

CD1

AUX1

1818

18

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 14) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 15)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 13) match the black wire to the

ground pin.

CPU Fan Connector You may connect either a 3-pin

(4-pin CPU_FAN1) or a 4-pin CPU fan cable to this

(see p.2 No. 5) connector, then match the black

wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 29)

COM Port Header This COM port header is used

(9-pin COM1) to support a COM port module.

(see p.2 No. 20)

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.

If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

1

2

3

4

1919

19

ASRock ConRoe865GV Motherboard

EnglishEnglish

English

ATX 12V Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 2) ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

2.82.8

2.8

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts Intel

®

ICH5 south bridge chipset that supports Serial ATA

(SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

Before you install OS into the SATA hard disk, you need to check and

ensure the configuration of the OnBoard IDE Operate Mode option in

BIOS setup is correct according to the condition of your system. For

the configuration details, please refer to the instruction on page 31 of

“User Manual” in the support CD.

2.92.9

2.9

Driver Installation GuideDriver Installation Guide

Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive first. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from up to bottom

side to install those required drivers. Therefore, the drivers you install can work

properly.

2.102.10

2.10

Untied Overclocking TUntied Overclocking T

Untied Overclocking T

echnologyechnology

echnology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to fixed PCI bus. You may set “CPU Host

Frequency” option of BIOS setup to [Auto], which will show you the actual CPU host

frequency in the following item. Therefore, CPU FSB is untied during overclocking,

but PCI bus is in the fixed mode so that FSB can operate under a more stable

overclocking environment.

2020

20

ASRock ConRoe865GV Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The BIOS Setup Utility is stored in the BIOS FWH chip. When you start up the

computer, please press <F2> during the Power-On-Self-Test (POST) to enter the

BIOS Setup Utility; otherwise, POST continues with its test routines. If you wish to

enter the BIOS Setup Utility after POST, please resume the system by pressing <Ctl>

+ <Alt> + <Delete>, or pressing the reset button on the system chassis. For the

detailed information about the BIOS Setup Utility, please refer to the User Manual

(PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

“LGA 775 CPU Installation Live Demo”

This motherboard is equipped with Intel LGA 775 socket, which is a new CPU

socket interface that Intel has released. Since it has several tiny pins, whcih

are easily to be damaged by improper handling, ASRock sincerely presents

you a clear installation guide through this “LGA 775 CPU Installation Live

Demo”. We hope you may check this live demo program before you start the

installation of LGA 775 CPU in order to reduce the risks of CPU and

motherboard damages caused by any improper handling. To see this Live

Demo, you can run Microsoft

®

Media Player

®

to play the file. You may find this

Live Demo in the motherboard’s Support CD through the following path:

..\ Live Demo \ LGA 775 CPU Installation \ LGA775INST_English.DAT

EnglishEnglish

English

La pagina sta caricando ...

ASROCK CONROE865GV Manuale del proprietario

ASROCK CONROE865GV Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti