ASROCK P4DUAL-915GL Manuale del proprietario

11

1

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published January 2005

22

2

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 Third Serial ATA Connector (SATA3, black)

2 ATX 12V Connector (ATX12V1) 17 Secondary Serial ATA Connector (SATA2, blue)

3 CPU Socket 18 Primary Serial ATA Connector (SATA1, blue)

4 CPU Heatsink Retention Module 19 System Panel Header (PANEL1)

5 CPU Fan Connector (CPU_FAN1) 20 USB 2.0 Header (USB67, Blue)

6 Infrared Module Header (IR1) 21 USB 2.0 Header (USB45, Blue)

7 184-pin DDR DIMM Slots 22 AMR Slot (AMR1)

(DDR1- 2, Dual Channel) 23 JR1 / JL1 Jumpers

8 BIOS FWH Chip 24 Front Panel Audio Header (AUDIO1)

9 Floppy Connector (FLOPPY1) 25 PCI Slots (PCI1- 2)

10 Primary IDE Connector (IDE1, Black) 26 Clear CMOS Jumper (CLRCMOS1)

11 Chassis Fan Connector (CHA_FAN1) 27 ASRock Graphics Interface Slot (AGI)

12 COM Port Header (COM1) 28 AGI Express Slot (PCI Express x 4)

13 South Bridge Controller 29 Internal Audio Connector: CD1 (Black)

14 Chassis Speaker Header (SPEAKER 1) 30 ATX Power Connector (ATXPWR1)

15 Fourth Serial ATA Connector (SATA4, black) 31 North Bridge Controller

33

3

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

ASRock 8CH I/OASRock 8CH I/O

ASRock 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 VGA Port

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

44

4

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P4Dual-915GL motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website as

well. ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock P4Dual-915GL Motherboard

(Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm)

ASRock P4Dual-915GL Quick Installation Guide

ASRock P4Dual-915GL Support CD

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock 8CH I/O

One COM Port Bracket

One ASRock MR Card (Optional)

55

5

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

1.2 Specifications1.2 Specifications

1.2 Specifications

Platform: Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm

CPU: Socket 478, supports Intel

®

Pentium

®

4

/ Celeron

®

(Prescott,

Northwood) processor

Chipsets: North Bridge:

Intel

®

915GL chipset, FSB @ 800 / 533MHz,

supports Hyper-Threading Technology (see CAUTION 1)

South Bridge:

Intel

®

ICH6, supports SATA 1.5Gb/s

Memory: 2 DDR DIMM slots: DDR1 and DDR2

supports PC3200 (DDR400) / PC2700 (DDR333),

Max. 2GB (see CAUTION 2)

Dual Channel Memory Technology support(see CAUTION 3)

IDE: IDE1: ATA 100 / Ultra DMA Mode 5, supports up to 2 IDE devices

Serial ATA: Supports up to 4 SATA devices at 1.5Gb/s data transfer rate.

(No Support for “RAID” and “Hot Plug” functions)

Floppy Port: Supports up to 2 floppy disk drives

Audio: 7.1 channels AC’97 Audio

PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor:CPU temperature sensing,

Chassis temperature sensing,

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 4),

CPU fan tachometer,

Chassis fan tachometer,

Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 2 PCI slots with PCI Specification 2.3

AMR slot: 1 slot, supports ASRock MR card (Optional)

AGI slot: 1 AGI [ASRock Graphics Interface] slot (see CAUTION 5)

AGI Express slot (PCI Express x 4):

1 slot with PCI Express x 4 , supports PCI Express x 16 Graphic

Card (see CAUTION 6)

USB 2.0: 8 USB 2.0 ports:

includes 4 default USB 2.0 ports on the rear panel,

plus two headers to support 4 additional USB 2.0 ports

(see CAUTION 7)

ASRock 8CH I/O: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port

1 VGA Port

1 Parallel Port (ECP/EPP Support)

4 Ready-to-Use USB 2.0 Ports, 1 RJ-45 Port

Audio Jack: Side Speaker / Rear Speaker / Central/Bass /

66

6

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

Line In / Front Speaker / Microphone

(see CAUTION 8)

COM Port: 1 COM Port Header to support a COM port module

BIOS: AMI legal BIOS, Supports “Plug and Play”,

ACPI 1.1 compliance wake up events,

Supports jumperfree, SMBIOS 2.3.1 support,

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 9)

OS: Microsoft

®

Windows

®

2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 25.

2. Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency Memory Support Frequency

800 DDR333, DDR400

533 DDR333, DDR400

* This motherboard doesn’t support 128Mbit DRAM Cell DIMM (128MB/8

cells; 256MB/16 cells; 512MB/32 cells).

3. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 11 for proper installation.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compatible

AGP VGA cards, please refer to the “Supported AGP VGA Card List for AGI

Slot” on page 7 and page 8. For the proper installation of AGP VGA card,

please refer to the installation guide on page 12.

6. For the information of the compatible PCI Express VGA cards, please

refer to the “Supported PCI Express VGA Card List for AGI Express Slot

(PCI Express x 4)” on page 9. For the proper installation of PCI Express

VGA card, please refer to the installation guide on page 12.

7. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 / 2000 SP4.

8. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel,

6-channel, and 8-channel modes. Please check the table on page 3 for

proper connection.

9. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

77

7

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

1.31.3

1.3

Supported AGP VGA Card List for AGI SlotSupported AGP VGA Card List for AGI Slot

Supported AGP VGA Card List for AGI Slot

(for Windows 2000/Windows XP)

I. AGP 4X

Graphics Chip Model Name

Vendor

n-VIDIA ASUS AGP-V8170

ASUS AGP-V9180 Magic

INNO3D GeForce4 MX440SE

Insignia GeForce MX440SE

LEADTEK A170TH

ATI GIGABYTE GV-AP64S-H

POWERCOLOR RADEON 9100

Transcend TS64MVDR7

For the latest updates of the supported AGP VGA card list for AGI slot, please

visit ASRock website for details.

ASRock website: http://www.asrock.com/support/index.htm

88

8

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

II. AGP 8X

Graphics Chip Model Name

Vendor

n-VIDIA ASUS AGP-V9570/TD

ASUS AGP-V9480

ASUS AGP-V9950ULTRA

ASUS AGP-V9520-X

ASUS AGP-V9570/TD

ASUS V9980 Ultra

ASUS V9999 Ultra/2DT

ASUS ASUS V9400MAGIC

ALBATRON GeForce FX5600Series

ALBATRON GeForce MX-480 Series

ALBATRON GeForce 6600

Aopen Aeolus Fx5200-DV 128

Awin FX5700-LE

ELSA AGP-518BL

GIGABYTE GV-N57L256D

LEADTEK WinFast A360TD

LEADTEK WINFAST A340TDH

LEADTEK WinFast A340PRO/TD

LEADTEK WinFast A400TDH

LEADTEK A6600GT/TDH

LEADTEK A280LE TD

MIS FX5700-TD128

Prolink PV-N36AX

PixeIView PV-N35XA

ATI Club 3D RADEON 9800

Connect 3D RADEON 9250

GECUBE RADEON 9250/128M

GIGABYTE GV-R9000 PRO

GIGABYTE GV-9500

MSI RX 9200 SE-T128

POWERCOLOR RADEON 9200SE

POWERCOLOR RADEON 9250/128M

For the latest updates of the supported AGP VGA card list for AGI slot, please

visit ASRock website for details.

ASRock website:

http://www.asrock.com/support/index.htm

Note. ATi 9600, 9550 series, and all Matrox series VGA cards are NOT supported

with AGI.

99

9

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

1.41.4

1.4

Supported PCI Express VGA Card List for AGISupported PCI Express VGA Card List for AGI

Supported PCI Express VGA Card List for AGI

Express Slot (PCI Express x 4)Express Slot (PCI Express x 4)

Express Slot (PCI Express x 4)

(for Windows 2000/Windows XP)

Graphics Chip Model Name Remark

Vendor

(VGA BIOS Version)

n-VIDIA ASUS Extreme N5900

ASUS EN6600

ASUS EN6800

ASUS Extreme N5750/A

ALBATRON GeFORCE 6200TC

GIGABYTE GV-NX66128D

GIGABYTE GV-NX62128D

MSI PCX 5750-TD128

SPARKLE GeFORCE 6200TC

ASUS EAX600XT

ASUS EAX800XT

ASUS EAX300LE-A334C/TD

ASUS EAX300LE-A334C R1.01

ASUS EAX300SE/T/N/128M/A R1.01

ASUS EAX700PRO/TVD/256M R1.00

ABIT X600XT

ELSA FALCOX X70 PRO 256B3 DTV

GIGABYTE GV-RX60P128D

For the latest updates of the supported PCI Express VGA card list for AGI Express

slot (PCI Express x 4), please visit ASRock website for details.

ASRock website:

http://www.asrock.com/support/index.htm

Note1. Turbo cache PCI Express x 16 VGA cards are not recommanded to use.

Note2. If you encounter any compatibility issue when installing above ATi X300 series

and X700 series graphics cards, please make sure to update the VGA BIOS

version according to the VGA BIOS Information in the table above.

ATI

BK-ATI VER008.015.117.000

BK-ATI VER008.015.115.000

AA30602-100

113-xxxxxx-xxx RV410_X9.BIN

1010

10

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down

the socket lever to secure the CPU. The lever clicks on the side tab to

indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

1111

11

ASRock P4Dual-915GL Motherboard

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

P4Dual-915GL motherboard provides two 184-pin DDR (Double Data Rate) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install two identical (the same brand, speed,

size and chip-type) memory modules in the DDR DIMM slots to activate Dual Chan-

nel Memory Technology. Otherwise, it will operate at single channel mode.

If you install only one memory module or two non-identical memory

modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

EnglishEnglish

English

1212

12

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

2.3 Expansion Slots (PCI, AMR, AGI, and AGI Express Slots)2.3 Expansion Slots (PCI, AMR, AGI, and AGI Express Slots)

2.3 Expansion Slots (PCI, AMR, AGI, and AGI Express Slots)

There are 2 PCI slots, 1 AMR slot, 1 AGI slot, and 1 AGI Express slot (PCI Express x

4) on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

AGI slot: The AGI [ASRock Graphics Interface] slot is a special design that only

supports compatible AGP VGA cards. For the information of the compat-

ible AGP VGA cards, please refer to the “Supported AGP VGA Cards List

for AGI Slot” on page 7 and page 8.

AGI Express slot (PCI Express x 4):

AGI Express slot (PCI Express x 4) is used to install PCI Express expan-

sion cards. For the information of the compatible PCI Express VGA cards,

please refer to the “Supported PCI Express VGA Card List forAGI Ex-

press Slot (PCI Express x 4)” on page 9.

1. If you install the add-on AGP VGA card or PCI Express VGA card,

BIOS setup will automatically disable the onboard VGA.

2. Please make sure to set the BIOS onboard VGA selection into “En

abled” if you want this motherboard to support Surround Display.

Then the onboard VGA in Windows will be the primary VGA card.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

1313

13

ASRock P4Dual-915GL Motherboard

2-pin jumper

Short Open

EnglishEnglish

English

2.4 Surround Display Feature2.4 Surround Display Feature

2.4 Surround Display Feature

Thanks to ASRock patented AGI8X and AGI Express Technology, this motherboard

supports Surround Display upgrade. With the internal onboard VGA and the

external add-on AGP VGA card and PCI Express VGA card, you can easily enjoy

the benefits of Surround Display feature. Please make sure to set the BIOS

onboard VGA selection into “Enabled”, and start your computer with onboard VGA

if you want this motherboard to support multi-monitors. For the detailed instruction,

please refer to the document at the following path in the Support CD: ..\ Surround

Display

2.5 Jumpers Setup2.5 Jumpers Setup

2.5 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1(see p.2 No. 23)

JL1(see p.2 No. 23)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS1, 2-pin jumper)

(see p.2 No. 26)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer andunplug the power cord, then use a jumper

cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to

remove the jumper cap after clearing the CMOS. If you need to clear the CMOS

when you just finish updating the BIOS, you must boot up the system first, and

then shut it down before you do the clear-CMOS action.

1414

14

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-Conductor ATA 66/100 cable

the red-striped side to Pin1

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 9)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Black)

(39-pin IDE1, see p.2 No. 10)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATA Connectors These four Serial ATA (SATA)

(SATA1: see p.2 No. 18) connectors support SATA data

(SATA2: see p.2 No. 17) cables for internal storage

(SATA3: see p.2 No. 16) devices. The current SATA

(SATA4: see p.2 No. 15) interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

SATA1 SATA2 SATA3 SATA4

1515

15

ASRock P4Dual-915GL Motherboard

connect to the

power supply

connect to the SATA

HDD power connector

CD1

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB67) dates 4 default USB 2.0 ports. If

(see p.2 No. 20) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB45) dates 4 default USB 2.0 ports. If

(see p.2 No. 21) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 6) and receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 29) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 24) convenient connection and

control of audio devices.

1616

16

ASRock P4Dual-915GL Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 19) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 14)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 11) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match

(see p.2 No. 5) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 30)

COM Port Header This COM port header is used

(9-pin COM1) to support a COM port module.

(see p.2 No. 12)

ATX 12V Connector Please connect an ATX 12V

(4-pin ATX12V1) power supply to this connector.

(see p.2 No. 2)

1717

17

ASRock P4Dual-915GL Motherboard

2.72.7

2.7

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts Intel ICH6 south bridge chipset that supports Serial ATA

(SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

Before you install OS into the SATA hard disk, you need to check and

ensure the configuration of the OnBoard IDE Operate Mode option in

BIOS setup is correct according to the condition of your system. For

the configuration details, please refer to the instruction on page 28 of

“User Manual” in the Support CD.

EnglishEnglish

English

1818

18

ASRock P4Dual-915GL Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The BIOS Setup Utility is stored in the BIOS FWH chip. When you start up the

computer, please press <F2> during the Power-On-Self-Test (POST) to enter the

BIOS Setup Utility; otherwise, POST continues with its test routines. If you wish to

enter the BIOS Setup Utility after POST, please resume the system by pressing <Ctl>

+ <Alt> + <Delete>, or pressing the reset button on the system chassis. For the

detailed information about the BIOS Setup Utility, please refer to the User Manual

(PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

1919

19

ASRock P4Dual-915GL Motherboard

2020

20

ASRock P4Dual-915GL Motherboard

® ® ®

®

La pagina sta caricando ...

ASROCK P4DUAL-915GL Manuale del proprietario

ASROCK P4DUAL-915GL Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti