WisyCom MCR41S-42S Manuale utente

Single-Dual True Diversity

Camera Receiver

SN: ________________

rev.14 (rif. FW 3.21)

Date: 25 June 2018

MCR41/MCR42 User Manual

1

BRIEF DESCRIPTION

MCR41/42 is a high performance microphone receiver suitable for broadcast and high

professional applications.

Thanks to Wisycom movable filter technology, MCR42 is able to work in a bandwidth up to 230

MHz, still keeping an exceptional selectivity and intermodulation immunity.

This miniature design allows to integrate a DUAL TRUE DIVERSITY receiver while keeping a small

size to fit camera slot in:

 Ikegami/Panasonic (UNISLOT™)

 Philips/Thomson/Grass Valley

 Sony

 Quad Pack & Six Pack

The audio receiver block is fully digital to allow a better quality, digital output and emulation of

most of companding chipsets. It supports also AES3 audio output with an overall sounds delay

below 1.5 msec.

MCR42 is designed to be:

 “easy & quick to use” thanks to automatic setup functions (i.e. frequencies, squelch,

scan), remote configuration utilities (thru infrared), an OLED display with intuitive

context menu navigation.

 “extremely flexible”, with an incredible frequency agility up to 230MHz. Moreover the

DSP board allows analogue and digital (AES3) output, with multi-companding

compatibilities and other digital features.

 “best in class performances”, thanks to the latest Wisycom technology the unit has

extreme RF sensitivity and immunity and superb audio quality.

 “a durable & upgradable investment”, thanks to the very robust design (aluminium

housing) and the possibility to upgrade/enhance units performances.

Moreover MCR42 system is already set up for the exclusive PTT function (remote command),

developed and patented by Wisycom and now appreciated in the broadcast world:

Simply pushing this button (PTT), the presenter causes the remote switching of the receiver’s

output-line, from the “main line” to the additional “intercom line”, in order to be able to talk “off-

air” directly with the technical team. Then all PTT’s MICs can be connected in pre-fading allowing a

clever intercom setup.

MCR41/MCR42 User Manual

2

SAFETY INSTRUCTION

 Read this safety instruction and the manual first

 Follow all instructions and information.

 Do not lose this manual.

 Do not use this apparatus under the rain or near the water.

 Do not install the apparatus near heaters or in hot environments, do not use outside the

operating temperature range.

 Do not open the apparatus, only qualified service technician are enabled to operate on it. The

apparatus needs servicing when it is not properly working or is damaged by liquids, moisture

or other objects are fallen in the apparatus.

 Use only accessories or replacement parts authorized or specified by the manufacturer.

 Clean the apparatus only with dry cloths, do not use liquids.

 Report the serial number and the purchasing date in front of the manual. It is needed to have

proper replacement parts or accessories from the manufacturer.

 When replacement parts are needed, use only replacement parts authorized from the

manufacturer. Substitution with not authorized parts could result in electric shock, hazards or

fire.

 Keep attention on all the labels with warnings or hazards on the apparatus.

WARNING: The apparatus is intended for professional use; anyway the manufacturer alerts the

user that the headphone output power of the apparatus could exceed the level of 85 dB(A) of

sound pressure level and this could be dangerous for the hearings. Do not use the headphone with

high power level or for long time. Reduce the power or suspend the hearing in case of any kind of

hearing problem.

WARNING: when operating thru battery pack always replace ALL BATTERIES.

DO NOT operate the device with some new and some old batteries.

When MCR42 is setup to “automatically turn on”, DO CHANGE ALL OF USED BATTERIES after

automatic low batteries shutdown.

MCR41/MCR42 User Manual

3

MAIN FEATURES

MCR41/42(*) is a camera dual true diversity wireless-microphone receiver system in a modular

stand-alone or slot-in configuration (compatible with most camera’s slot):

 Extreme RF (radiofrequency) performances and reliability

 Extreme frequency agility (tuning windows up to 240 MHz with independent tunable

filters on 2 ch’s):

- MCR42-N 470÷700 MHz

- MCR42-M: 566÷798 MHz

- MCR42-L: 470÷678 MHz

- MCR42-H:590÷822 MHz

(extended range up to 830 available on request and upon your country-specific

regulations)

 digital output on AES3

 multi-companding compatibility

 40 groups of 60 channels fully user

programmable (2400 frequencies!!)

 future digital functionality enhancements

 Automatic scan for best channels, squelch and other automatic setup

 Infrared interface (i.e. for system setup, microphone programming)

 Automatic transmitter re-programming (thru infrared, sync function)

 Push to Talk (PTT) function with additional audio output signals (patented)

(*) Note MCR41 is the version with only one diversity RX board mounted. It supports all features of

MCR42 and is compatible with MCR42 Firmware.

It is also possible to mount the second Rx board to upgrade a MCR41 to an MCR42.

Technical description

The MCR42 is a professional dual true diversity receiver for wireless microphones reception

especially designed for broadcast production, live stages, theatres and top professional

applications.

It’s winning performances are:

 High immunity on strong RF environment

 Huge switching bandwidth

 High audio performances and flexibility with analog or digital processors

 High reliability and durability

One of the milestones in the design of the MCR42 is high reliability: most of the circuitry of the

receiver is independent one from each other.

40 Groups

60 Channels

MCR41/MCR42 User Manual

4

Above a schematic with an overview of main receiver functions.

For each antenna the RF signal is split in the receiver 1 and in the receiver 2 (antenna A and

antenna B) with a wide band splitter. In this way any one receiver could be tuned in any frequency

of the switching range (typ. 240 MHz).

Receiver 1 and 2 are diversity receivers: each one is made of two receivers tuned on the same

frequency, hereafter called section A and section B. The receiver 1 section A and the receiver 2

section A are connected to the antenna A, the receiver 1 section B and the receiver 2 section B are

connected at the antenna B.

Each receiver has its own demodulated signal and its own RSSI signal (Receiver Signal Strength

Indication); a DSP selects or combines signals from section A & B to have the best audio.

The demodulated signal flows to the digital audio processor.

the data sub carrier is digitally filtered to a very selective equivalent bandwidth (3Hz). Each filter

has its own data demodulator, one for medium speed data detection at the output of the first filter

and one at low speed data detection at the output of the second filter. All the two demodulators

are connected to the supervisor micro controller for the data battery detection and signalling.

Digital audio processor: the demodulated signal is filtered by an anti aliasing low pass filter and

then converted in the digital domain with a 96KHz 24bit audio A/D converter. The digital signal

processor (DSP), working in double precision, replicates all the analog functions with very high

accuracy, ultra low distortion and without typical analog problems like components tolerances or

long term drifts or temperature drifts etc. The high speed audio algorithms implemented in

assembler into the MCR42 maintains the audio delay at about 1.3 milliseconds, making it ideally

for live events and to keep audio delay as short as possible. The DSP unit also filters and

demodulates the data carrier and communicates all the parameters and informations to the

supervisor micro controller. The audio output goes to the digital outputs (AES3) or is converted in

the analog domain with a high quality 24 bits 96KHz D/A converter and an anti-aliasing filter.

Receiver -1-A

Receiver -1-B

Receiver -2-A

Receiver -2-B

TrueDiversity

Control Rx1

True Diversity

ControlRx2

Communic.

and control

interface

Receiver supervisor

microcontroller

and userinterface

Front panel

Digital

output

A

B

Antennainputs

Line1

Line2

ComRx1

ComRx2

INFRARED

SERIALLINK

Analogue

output

PTT

output

Ear-ph Left

Ear-ph Right

Ear-

phone

MCR41/MCR42 User Manual

5

USER GUIDE

NEW DISPLAY

Front Panel

MCR42 allows an easy and quick configuration using buttons, RGB LED’s and an OLED display. The

front panel is functionally divided in the following section:

A & B SMA antenna Connector:

MCR42 is supplied with a couple of antenna tuned on 400 MHz bandwidth suitable to be used with

MCR42-N, MCR42-M, MCR42-L, MCR42-H version.

C RGB Leds: Each of the 2 receivers has a dedicated set of LED’s to give a clear indication of its

status.

“ON LED” (on NEW display)

GREEN

The receiver is on with an external power supply

PALE GREEN

The receiver is on with battery

GREEN BLINKING

The external power is low

PALE GREEN BLINKING

The power of the battery is low

RED BLINKING

Relative transmitter battery is

low:

- slowly blinking if 25% lifetime

- quickly blinking if 12% lifetime

When the “ON LED” become red blinking,

the display, if it is off, it automatically turns

on and remains on until the alarm does not

fall.

A

C

B

C

D

E

F

G

MCR41/MCR42 User Manual

6

“ON LED” (on OLD display)

OFF

Relative receiver is not active

GREEN

Relative receiver is active and battery/external power is not low

RED

Relative receiver is active and battery/external power is low

RED BLINKING

Relative transmitter battery is low:

- slowly blinking if 25% lifetime

- quickly blinking if 12% lifetime

“RF LED”

OFF

Relative receiver is not active

RED

RF level below squelch on both diversity receivers

GREEN

RF level above squelch and receiver A is active (ANTENNA A)

BLUE

RF level above squelch and receiver B is active (ANTENNA B)

“AUDIO/AF LED”

RED

Audio muted due to RF squelch or tone squelch

GREEN

Audio active & tone squelch detected

BLUE

Audio active & tone squelch not detected (or when calibration tone is active)

D “MENU/SEL” BUTTON

Push this button to navigate function menu’s and to confirm the chosen setup.

F “PWR/EXIT” BUTTON

Push and keep this button to power on/off the receiver. The on/off status is permanently

memorized into the non-volatile memory, this way the system can be setup to automatically turn

on Rx1, or Rx2, or both, when power up.

During menu navigation push this button to exit from current menu (escape function).

E “Arrow up/sync” BUTTON

Push and keep this button to start a synchronization with a Wisycom transmitter (follow instructions

on display). Before starting synchronization IRDA must be enabled on Wisycom transmitter.

During menu navigation push this button to move -up and select the previous item.

G “Arrow down/scan” BUTTON

Push and keep this button to start the automatic scan.

During menu navigation push this button to move-down and select the previous item.

H “OLED Display”

The receiver has a high contrast display. Pushing a button while the receiver is active, turn on

automatically the display. After a time-out the display turns off automatically.

MCR41/MCR42 User Manual

7

Display menu

Using navigation buttons it is possible to quick & easy navigate through the MCR42 menu:

- SEL/Exit to enter or exit a level

- Arrow up/down to circle on the same level

- To save the modified parameters press and hold the SEL /MENU button ( ) until appears the

message "SAVED!".

Tree Menu (ref. firmware version v3.21)

According to the MCR42 model, different audio levels (analogue) are available (see below table).

Model

Features

Max audio

level (anal.)

SND/D

ratio

(Analogue)

SND/D ratio

(AES3)

Distortion

MCR42

first hardware

-18÷12dBu

110 dB typ.

125 dB typ.

0.3 % typ

MCR42S

new main and new display

-30÷12dBu

MCR42S2

new Rx

140 dB typ.

0.1 % typ.

MCR42S3

new main,top feed configuration

-30÷18dBu

MAIN

Infrared

Preset

Restore PRESET_1 / PRESET_2 / PRESET_3 / Factory

Save PRESET_1 / PRESET_2 / PRESET_3

Advanced

Info

Power

Model

Serial

Range

Base

Alim

FW

Version

BL

App

DSP

HW

HW rev

Options

Top

Display

Errors

MCR41/MCR42 User Manual

8

Advanced

MCR41/MCR42 User Manual

9

STATUS MENU

Quick Menu

From FW version 3.0, pushing “Arrow down/scan” button or “Arrow up/sync”

button, it’s possible to enter in a circular menu where you can see the main

parameters of the receiver as frequency, group, channel, Expander, RF level,

squelch and audio level.

The screens of the circular menu are described in the following table

Status Screen

RX1

RX2

Group

Channel

RF bar

(8 steps of 10dBµV,

from 10 to 80 dBµV)

Squelch Level

Frequency

TX battery

Level

Modulation bar

(from -42 to 0 dB)

Peak deviation ≥

56KHz

By name

By Ch/Gr

MCR41/MCR42 User Manual

10

Depending on what is set on the parameter “Fast ch sel” in the

Main menu, in the first and second screen of the circular

menu it’s possible to see:

- N° RX, Frequency, group (and name) and channel or

- N° RX, Name of the channel, group (and name), Expander

and channel

of receiver 1 (first screen) and receiver 2 (second screen)

Pushing SEL button it’s possible to change freq/GR/CH.

From FW 3.0 and above, it’s possible to assign a name and an

Expander to a channel using the Wisycom MCR4x Manager

v.1.0.1 or above (to understand how to do it, read How to

assign a name and an expander to a channel on the Wisycom

MCR4x Manager guide)

Note: It’s not possible to change name and expander of a channel

from the device (only from Wisycom MCR4x Manager)

In the third screen are showed the instant RF levels of the two

receivers (❸,❹) and it is showed the minimum, maximum

and average value calculated in a time frame of about 4

minutes (❻,❼).

In this screen are showed:

❶ the number of the receiver

❷ an indication bar from 0 to 70 dBµV with step of 10dBµV

❸ two bars that indicate the RF level on antenna A (above)

and B (below)

❹ the current RF level of the antenna with the highest level in

dBµV

❺ the level of squelch

❻ an indication bar to see the min, max and average RF level

in the recorded time (about 4 minutes). At the end of the

recording time, the indication bar stop to update the RF

levels (it can be used to make a walk test).

❼ a time bar that indicates the recording time of the RF level.

On the left of the time bar there is a blinking triangle that

disappear at the end of the recording time.

Pushing SEL button it’s possible to change the squelch level

automatically or manually (one RX at a time).

❼

❸

❹

❺

❹

❺

❸

❷

❻

❶

By name

By Ch/Gr

MCR41/MCR42 User Manual

11

In the fourth screen are displayed the main audio information

In this screen are showed:

❶ the number of the receiver

❷ the Expander

❸ the max audio level

❹ an indication bar from -42 to 0 dB with step of 6dB

(0dB peak deviation ≥ 56KHz)

❺ the modulation level with the indicator of modulation

peak (when the indicator goes to 0dB, the square on the

right of the display become white for about 1 second to

highlight the peak occurred)

Pushing SEL button it’s possible to enable the Calibration Tone

and set the max audio level of the outputs:

- LINE max lev: -8÷12 dBu (only for HW rev ≥ 21)

- MIC max lev: -30÷10 dBu (only for HW rev ≥ 21)

- LINE max lev: -18÷12 dBu (only for HW rev < 21)

- AES max lev: -30÷0 dBFS

- COM max lev: -18÷12 dBu (only with BPA42-PTT)

MAIN MENU

Infrared:

By activating the infrared, you can connect the MCR42 to

other devices (such as a UPK300)

Preset:

The preset menu has the following two submenus:

 Restore: that allows to reload 3 different presets

(PRESET_1, 2, 3) earlier saved or a Factory preset (a preset

load in the Wisycom factory)

 Save: that allows to save 3 different presets (PRESET_ 1, 2,

3)

Each saved preset consists of all user parameters indicated

in blue in the graphic on page 8 (Display menu).

❶

❷

❸

❹

❺

❶

❷

❸

❺

Step 1dB

MCR41/MCR42 User Manual

12

Advanced:

Select Advanced menu to access to other advanced

parameters

Info

In the info menu the following information are displayed:

Info

description

example

Power:

Supply voltage measured

12.0Volt

Model:

MCR42 dual rx / MCR41

MCR42 dual rx

Serial:

The serial number composed by 1 letter+7 numbers

S3536539

Range:

Frequency range according to the MCR band:

L: 470-678

H: 590-822

N: 470-700

M: 566-798

470-678

Base:

Version of rear panel:

BPA42-PTT/HPN/BAG

S1LK 42-SX

SLK 42-IK

SLK 42-PH

BPA42-HPN

Alim:

Type of power supply

Ext

FW:

Version:

FW version

v2.0.5

BL:

Bootloader version

v.1.0.18

App:

Application version

v2.5d

DSP:

DSP version

v0.0.55r

HW:

HW rev:

Hardware version

21

Options:

For this product the option specific the band (L/H/N/M)

L

Top:

Indicates if there is mounted a Top Feed and the type

EL2

Display

0 if there is an old display / 1 if there is a new display

1

Errors:

Number of errors.

If the number of errors is > 0 push SEL button to enter on the Errors list.

For each error a brief description and the error code is showed.

For more information, please see the Error List section.

0

MCR41/MCR42 User Manual

13

Advanced Menu

Power on (only for MCR42, not MCR41)

Allow to enable both the receivers:

Only receiver 1 (Rx1), only receiver (Rx2) or (Rx1 + Rx2).

Edit RX (MCR42 has the same menu for RX1 and RX2)

Selecting this sub-menu most of RX1 or RX2 setups are

configurable.

Edit RX: Name

Selecting Name, it’s possible to edit the name of the receiver

(12 characters). The number of visible characters in the

parameter Name depends on the type of characters used

(uppercase or lowercase characters).

Edit RX: GR-Ch

Select current group and channel.

Group name and channel frequency are displayed on the

right.

Edit RX: Frequency

If the specific group/channel is not locked, then can be

edited in this menu.

Edit RX: Squelch

This menu allows to disable the RF squelch (OFF) or to setup

the desired squelch level in dBµV (note 0 dBµV is equal to -

107 dBm).

MCR41/MCR42 User Manual

14

Edit RX: Expander

MCR41/42 supports 4 different type of “Expanding systems”

(other on request)

ENR-Wisy: designed for maximum noise reduction

ENC-Wisy: designed for maximum audio fidelity (use this in

case of special vocal application or to remote

instruments)

ENR-1.2*/ENC-1.2*: to use MCR42 with some type of

camera (ex. Canon® C300, Canon® XF305, Sony®

Pmw200, Sony® Pmw300, Sony® PmwF5, Sony® Fs7,

Nikon® D600 or Nikon® D800, Canon® SD mark3...)

which accept a signal with reduced dynamic. This

type of expansion doesn't add artifacts to the signal

and allows to have a less noisy signal. It allows to

improve the quality of the audio registration

(compared to the ENR/ENC standard) increasing the

S/N ratio up to 15dB.

To use these expanders, it’s necessary to set ENR on

the transmitter and ENR 1.2 on the receiver or set

ENC on the transmitter and ENC 1.2 on the receiver.

ENR-1.2 it’s used for the optimization of noise, ENC-

1.2 it’s used to optimize the voice.

NB: The compander of the receiver must be the same as the

transmitter

MCR42 core is a power digital audio processor that, besides

an unbeatable audio quality and flexibility, can emulate

most expanders systems on the market. On this menu you

can setup the audio expanding chipset emulation. ENR is

emulating the Philips™ SA572 and PTT digital data of

Wisycom transmitters. Other setups can be loaded on

request.

*Available only from FW v3.3

Canon is a trademark of Canon Incorporated, Nikon is a trademark of Nikon Corp,

Sony is a trademark of Sony Corp.

MCR41/MCR42 User Manual

15

Edit RX: Tone Squelch

MCR42 is able to detect a digital tone squelch generated by

a Wisycom transmitters (ex. MTH400/MTH300/MTP40/

MTP30).

Tone squelch ON: when the tone squelch is enabled the

audio is muted unless the correct carrier is detected. Tone

squelch allows to work with lower RF squelch, increasing the

coverage and the robustness especially in presence of digital

television carriers (DVB-T).

Tone squelch ADVanced: when tone squelch is in advanced

mode the receiver processes also PTT data (push to talk):

activating the command audio output when the button is

pressed on remote transmitter.

When tone squelch is off it is possible to choose where to

put the output between LINE and COM.

The COM column is present only using the Stand alone socket

BPA42-PTT

When tone squelch is set to ON it is possible to choose

where to put the output between LINE and COM.

The COM column is present only using the Stand alone socket

BPA42-PTT

When tone squelch is in advanced mode it is possible to

access a more complex audio matrix where to put the

output between LINE and COM and between PTT rel.

(released) and PTT psh (pushed)

Usually Line is always ticked and Com (PTT) is ticked on “PTT

push.” as additional return channel (intercom).

The COM column is present only using the BPA42-PTT

NOTE: With squelch and tone squelch the audio output is activate when:

Squelch OFF

Squelch = 0,3,6,… dBµV

Tone squelch OFF

Always

RF level ≥ Squelch

Tone squelch ON

If tone is detected

RF level ≥ Squelch & tone squelch

is detected

MCR41/MCR42 User Manual

16

Edit RX: Audio Out

In Audio Out it’s possible to set the maximum audio output.

For MCR42 with Hardware version ≥ 21, the max audio level

of the RX1/RX2 output can be set from -30dBu to -10 dBu (in

the first selection appears “MIC max lev”) and from -8dBu

to +12 dBu (in the first selection appears “LINE max lev”)

For MCR42 with Hardware version < 21, the max audio level

of the RX1/RX2 output can be set from -18dBu to -12

dBu (“LINE max lev”)

The max audio level of the COM output can be set from -18

dBu to +12 dBu in one dB step.

The max audio level of the AES3 output can be set from -

30dBFS to 0 dBFS in one dB step.

Edit RX: Sig. Phase

To change audio phase of 0 deg or 180 deg.

Edit RX: Scan

This function can be called also using the dedicated scan

button (push and keep). It allows to make a scan over a

desired frequency group.

MCR42 manages up to 2400 custom frequencies organized

in 40 groups of 60 channels each. This extreme flexibility

makes the scan function very flexible.

Once started a scan operation the receiver asks for group to

be used.

Then it prompts to turn off all transmitters.

Then finally start the scan!

After few seconds, scan results are displayed on a chart.

MCR41/MCR42 User Manual

17

Results can be also displayed sorted by level (pushing

together SYNC and SCAN buttons), making easier to pick up

the best one.

NOTE: As per Wisycom standard, group 00 and group 01 or 09 are special; respectively the “center

frequency” (474,482/... MHz) and the intergap frequency (i.e. 470/478/486/... MHz). A scan on

group 00 will reveal in few seconds the overall DVB-T occupation on the area, while a scan on group

0 or 09 will give possible working frequency, usable also in presence of strong DVB-T signal (sort to

speak working in the band-guard of 2 digital television channel).

Edit RX: Cal. tone

If Cal. tone is enabled, a calibration tone is transmitted from

the outputs of the receiver and the audio LED of the relative

RX become blue (to turn off the calibration tone, go on the

menu Advanced > RX and press EXIT)

It’s possible to select the audio level between -18dB and 0

dB.

The calibration tone at 0dB it’s used to generate a tone at

1KHz at the maximum output level (depending on the

MIC/LINE max level or COM max level set in the Audio out

menu). It represent the reference of the peak deviation

(56KHz).

LINE mode:

In LINE mode is settable the type of output between analog

and AES3 (digital).

NOTE: When LINE mode is set to AES3 the digital output

(Rx1+Rx2 in digital) is available on Rx1 output.

MCR41/MCR42 User Manual

18

Headphones (only for BPA42-HPN)

Cycle through menu’s with up/down arrow to get your

desired configuration then confirm with SEL.

Volume: It is possible to set the desired output level from

Max (+6 dB) to min (-24 dB) in 1 dB step.

Balance: with this parameter it’s possible to balance the

delta of the volume between Left and Right on the

headphones (it’s possible to set up to 12dB between L/R).

For example: if volume is set to 0dB and Balance to R+4, in

the HP output, L will be -2dB and R will be 2dB.

RX mix: if the parameter RX sel is set to Rx1+Rx2(L+R), it’s

possible to balance the delta of the volume between RX1

and RX2 (it’s possible to set up to 12dB between RX1/RX2).

For example: if volume is set to 0dB, Rx signal to

Rx1+Rx2(L+R) and RX mix to Rx1+6, in the HP output, RX1

will be at 3dB and RX2 will be at -3dB.

RX sel: Left and right channel of stereo jack can be mapped

respectively on RX1, RX2 or on RX1+RX2.

Signal: If set to LINE, on the headphones there is the same

signal of the output LINE. If set to TSQ>LINE and the Tone

Squelch is enable (Tone Squelch ON or ADV), on the

headphones it is possible to hear the signal even when the

Tone Squelch is not detected.

Example: if Volume= 0dB & Balance= R+4

RX1

RX2

DSP

L=-2dB

R=2dB

Δ=4dB

0dB

2dB

-2dB

Delta is centered on the set

Volume (in this case 0dB)

L

R

0dB

3dB

-3dB

Delta is centered on the set

Volume (in this case 0dB)

RX2

RX1

(RX1@3dB)+(RX2@-3dB)

RX1

RX2

DSP

Example: if Volume=0dB, RX sel= Rx1+Rx2(L+R) & RX mix= Rx1+6

+

L

R

Δ=6dB

MCR41/MCR42 User Manual

19

Fast ch sel:

This menu allow to set what to see in the first two screens of

the Quick Menu.

It’s possible to set:

- By Ch/Gr = Frequency, group (and propriety) and channel;

- By name = Name of the channel, group (and propriety)

channel and Expander.

of receiver 1 (first screen) and receiver 2 (second screen)

Display:

In this menu item it’s possible to set the mode of switch on

of the front LEDs and the contrast and timeout of the

display.

LEDs mode can be:

 Full: all LEDs are activate as indicated on

-USER GUIDE - Front Panel

 Alarm: the LEDs are ON only in case of alarm

(only red)

 OFF: all LEDs are always off

Low timeout indicates the time until the display stays on

with the contrast set (after which, the display contrast is

lowered and after another “Low timeout” the display shows

the Status screen).

Off timeout is the time until the display stays on (after

which, the display will automatically turn off). If Off timeout

is set to OFF the display never turn off automatically.

Sync:

With the MCR41/42 you can synchronize your device with

others via the sync function.

After the selection of the desiderate receiver that you

want to synchronize (RX1 or RX2 for MCR42), pull the

infrared sensors of the 2 devices and wait for it to

synchronize. At the end of this operation the 2 devices will

be synchronized to the same frequency.

La pagina sta caricando ...

WisyCom MCR41S-42S Manuale utente

WisyCom MCR41S-42S Manuale utente

in altre lingue

Documenti correlati

Altri documenti