Roland UA-3 Manuale del proprietario

02673845 1*SX

Owner’s Manual page 5

Bedienungsanleitung page 26

Mode d’emploi page 47

Manual del usuario page 68

Manuale d’uso page 89

201a

Before using this unit, carefully read the sections entitled:

“USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2, p.

4). These sections provide important information concerning the

proper operation of the unit. Additionally, in order to feel assured

that you have gained a good grasp of every feature provided by

your new unit, Getting Started manual should be read in its

entirety. The manual should be saved and kept on hand as a

convenient reference.

without the written permission of ROLAND CORPORATION.

Information

When you need repair service, call your nearest Roland/EDIROL Service Center or authorized Roland/EDIROL distributor

in your country as shown below.

U. S. A. / CANADA

EDIROL Corporation North

America

425 Sequoia Drive, Suite 114

Bellingham, WA 98226

U. S. A.

TEL: (360)594-4276

FAX: (360)594-4271

http://www.edirol.com/

AUSTRALIA

EDIROL Australia Pty. Ltd.

72 Central Avenue

Oak Flats NSW 2529

AUSTRALIA

TEL: (02) 4257 9091

http://www.edirol.com.au

EUROPE

EDIROL (Europe) Ltd.

Studio 3.4 114 Power Road

London W4 5PY

U. K.

TEL: +44 (0)20 8747 5949

FAX:+44 (0)20 8747 5948

http://www.edirol.com/europe

Deutschland

TEL: 0700 33 47 65 20

France

TEL: 0810 000 371

Italia

TEL: 02 93778329

As of April 23, 2001 (EDIROL)

EGYPT

Al Fanny Trading Office

P.O. Box 2904,

El Horrieh Heliopolos, Cairo,

EGYPT

TEL: (02) 4185531

REUNION

Maison FO - YAM Marcel

25 Rue Jules Hermann,

Chaudron - BP79 97 491

Ste Clotilde Cedex,

REUNION ISLAND

TEL: 28 29 16

SOUTH AFRICA

That Other Music Shop

(PTY) Ltd.

11 Melle St., Braamfontein,

Johannesbourg

Republic of SOUTH AFRICA

P.O.Box 32918, Braamfontein 2017

Republic of SOUTH AFRICA

TEL: (011) 403 4105

Paul Bothner (PTY) Ltd.

17 Werdmuller Centre Claremont

7700

Republic of SOUTH AFRICA

P.O. Box 23032

Claremont, Cape Town

SOUTH AFRICA, 7735

TEL: (021) 674 4030

AFRICAAFRICA

HONG KONG

Tom Lee Music Co., Ltd.

Service Division

22-32 Pun Shan Street, Tsuen

Wan, New Territories,

HONG KONG

TEL: 2415 0911

CHINA

Beijing Xinghai Musical

Instruments Co., Ltd.

6 Huangmuchang Chao Yang

District, Beijing, CHINA

TEL: (010) 6774 7491

ASIA

INDIA

Rivera Digitec (India) Pvt. Ltd.

409, Nirman Kendra Mahalaxmi

Flats Compound Off. Dr. Edwin

Moses Road, Mumbai-400011,

INDIA

TEL: (022) 498 3079

INDONESIA

PT Citra IntiRama

J1. Cideng Timur No. 15J-150

Jakarta Pusat

INDONESIA

TEL: (021) 6324170

MALAYSIA

Bentley Music SDN BHD

140 & 142, Jalan Bukit Bintang

55100 Kuala Lumpur,MALAYSIA

TEL: (03) 2443333

PHILIPPINES

G.A. Yupangco & Co. Inc.

339 Gil J. Puyat Avenue

Makati, Metro Manila 1200,

PHILIPPINES

TEL: (02) 899 9801

KOREA

Cosmos Corporation

1461-9, Seocho-Dong,

Seocho Ku, Seoul, KOREA

TEL: (02) 3486-8855

SINGAPORE

CRISTOFORI MUSIC PTE

LTD

Blk 3014, Bedok Industrial Park E,

#02-2148, SINGAPORE 489980

TEL: 243 9555

TAIWAN

ROLAND TAIWAN

ENTERPRISE CO., LTD.

Room 5, 9fl. No. 112 Chung Shan

N.Road Sec.2, Taipei, TAIWAN,

R.O.C.

TEL: (02) 2561 3339

THAILAND

Theera Music Co. , Ltd.

330 Verng NakornKasem, Soi 2,

Bangkok 10100, THAILAND

TEL: (02) 2248821

VIETNAM

Saigon Music

138 Tran Quang Khai St.,

District 1

Ho Chi Minh City

VIETNAM

TEL: (08) 844-4068

ARGENTINA

Instrumentos Musicales S.A.

Florida 656 2nd Floor

Office Number 206A

Buenos Aires

ARGENTINA, CP1005

TEL: (54-11) 4- 393-6057

BRAZIL

Roland Brasil Ltda

Rua San Jose, 780 Sala B

Parque Industrial San Jose

Cotia - Sao Paulo - SP, BRAZIL

TEL: (011) 4615 5666

NEW ZEALAND

Roland Corporation (NZ) Ltd.

97 Mt. Eden Road, Mt. Eden,

Auckland 3, NEW ZEALAND

TEL: (09) 3098 715

AUSTRALIA/

NEW ZEALAND

CENTRAL/LATIN

AMERICA

MEXICO

Casa Veerkamp, s.a. de c.v.

Av. Toluca No. 323, Col. Olivar

de los Padres 01780 Mexico D.F.

MEXICO

TEL: (525) 668 04 80

La Casa Wagner de

Guadalajara s.a. de c.v.

Av. Corona No. 202 S.J.

Guadalajara, Jalisco Mexico

C.P.44100 MEXICO

TEL: (3) 613 1414

PANAMA

SUPRO MUNDIAL, S.A.

Boulevard Andrews, Albrook,

Panama City,

REP. DE PANAMA

TEL: (507) 315-0101

VENEZUELA

Musicland Digital C.A.

Av. Francisco de Miranda,

Centro Parque de Cristal, Nivel

C2 Local 20 Caracas

VENEZUELA

TEL: (02) 285 9218

URUGUAY

Todo Musica S.A.

Cuareim 1844, Montevideo,

URUGUAY, CP11200

TEL: 5982-924-2335

DENMARK

Roland Scandinavia A/S

Nordhavnsvej 7, Postbox 880,

DK-2100 Copenhagen

DENMARK

TEL: (039)16 6200

FRANCE

Roland France SA

4, Rue Paul Henri SPAAK,

Parc de l'Esplanade, F 77 462 St.

Thibault, Lagny Cedex FRANCE

TEL: 01 600 73 500

FINLAND

Roland Scandinavia As,

Filial Finland

Lauttasaarentie 54 B

Fin-00201 Helsinki, FINLAND

TEL: (9) 682 4020

GERMANY

Roland Elektronische

Musikinstrumente HmbH.

Oststrasse 96, 22844 Norderstedt,

GERMANY

TEL: (040) 52 60090

HUNGARY

Intermusica Ltd.

Warehouse Area ‘DEPO’ Pf.83

H-2046 Torokbalint, HUNGARY

TEL: (23) 511011

AUSTRIA

Roland Austria GES.M.B.H.

Siemensstrasse 4, P.O. Box 74,

A-6063 RUM, AUSTRIA

TEL: (0512) 26 44 260

BELGIUM/HOLLAND/

LUXEMBOURG

Roland Benelux N. V.

Houtstraat 3, B-2260, Oevel

(Westerlo) BELGIUM

TEL: (014) 575811

EUROPE

GREECE

STOLLAS S.A.

Music Sound Light

155, New National Road

26422 Patras, GREECE

TEL: 061-435400

IRELAND

Roland Ireland

Audio House, Belmont Court,

Donnybrook, Dublin 4.

Republic of IRELAND

TEL: (01) 2603501

ITALY

Roland Italy S. p. A.

Viale delle Industrie 8,

20020 Arese, Milano, ITALY

TEL: (02) 937-78300

NORWAY

Roland Scandinavia Avd.

Kontor Norge

Lilleakerveien 2 Postboks 95

Lilleaker N-0216 Oslo

NORWAY

TEL: 273 0074

PORTUGAL

Tecnologias Musica e Audio,

Roland Portugal, S.A.

Cais Das Pedras, 8/9-1 Dto

4050-465 PORTO

PORTUGAL

TEL: (022) 608 00 60

POLAND

P. P. H. Brzostowicz

UL. Gibraltarska 4.

PL-03664 Warszawa POLAND

TEL: (022) 679 44 19

RUSSIA

Slami Music Company

Sadojava-Triumfalnaja st., 16

103006 Moscow, RUSSIA

TEL: 095 209 2193

SPAIN

Roland Electronics

de España, S. A.

Calle Bolivia 239, 08020

Barcelona, SPAIN

TEL: (93) 308 1000

SWITZERLAND

Roland (Switzerland) AG

Musitronic AG

Gerberstrasse 5, Postfach,

CH-4410 Liestal, SWITZERLAND

TEL: (061) 921 1615

SWEDEN

Roland Scandinavia A/S

SWEDISH SALES OFFICE

Danvik Center 28, 2 tr.

S-131 30 Nacka SWEDEN

TEL: (08) 702 0020

UKRAINE

TIC-TAC

Mira Str. 19/108

P.O. Box 180

295400 Munkachevo, UKRAINE

TEL: (03131) 414-40

UNITED KINGDOM

Roland (U.K.) Ltd.

Atlantic Close, Swansea

Enterprise Park, SWANSEA

SA7 9FJ,

UNITED KINGDOM

TEL: (01792) 700139

ROMANIA

FBS LINES

Piata Libertatii 1,

RO-4200 Gheorgheni

TEL: (066) 164-609

BAHRAIN

Moon Stores

Bab Al Bahrain Road,

P.O. Box 20077

State of BAHRAIN

TEL: 211 005

ISRAEL

Halilit P. Greenspoon &

Sons Ltd.

8 Retzif Ha’aliya Hashnya St.

Tel-Aviv-Yafo ISRAEL

TEL: (03) 6823666

JORDAN

AMMAN Trading Agency

Prince Mohammed St. P.O. Box

825 Amman 11118 JORDAN

TEL: (06) 4641200

KUWAIT

Easa Husain Al-Yousifi

Abdullah Salem Street,

Safat KUWAIT

TEL: 5719499

LEBANON

A. Chahine & Fils

P.O. Box 16-5857 Gergi Zeidan St.

Chahine Building, Achrafieh

Beirut, LEBANON

TEL: (01) 335799

CYPRUS

Radex Sound Equipment Ltd.

17 Diagorou St., P.O. Box 2046,

Nicosia CYPRUS

TEL: (02) 453 426

IRAN

MOCO, INC.

No.41 Nike St.Dr.Shariyati Ave.

Roberoye Cerahe Mirdamad

Tehran, IRAN

TEL: 285 4169

MIDDLE EAST

QATAR

Badie Studio & Stores

P.O. Box 62,

DOHA QATAR

TEL: 423554

SAUDI ARABIA

aDawliah Universal

Electronics APL

Corniche Road, Aldossary Bldg.,

1st Floor

SAUDI ARABIA

P.O.Box 2154, Alkhobar 31952

SAUDI ARABIA

TEL: (03) 898 2081

SYRIA

Technical Light & Sound

Center

Khaled Ibn Al Walid St.

P.O. Box 13520

Damascus - SYRIA

TEL: (011) 2235 384

TURKEY

Barkat Muzik aletleri ithalat

ve ihracat Ltd Sti

Siraselviler cad.Guney is hani 84-

86/6, Taksim. Istanbul. TURKEY

TEL: (0212) 2499324

U.A.E.

Zak Electronics & Musical

Instruments Co. L.L.C.

Zabeel Road, Al Sherooq Bldg.,

No. 14, Grand Floor DUBAI

U.A.E.

TEL: (04) 3360715

2

This product complies with the requirements of European Directive 89/336/EEC.

For EU Countries

For Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

NOTICE

AVIS

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment.

This equipment requires shielded interface cables in order to meet FCC class B Limit.

For the USA

DECLARATION OF CONFORMITY

COMPLIANCE INFORMATION STATEMENT

Model name: UA-3

Type of Equipment: USB Audio Interface

Responsible Party: Edirol Corporation North America

Address: 425 Sequoia Drive, Suite 114, Bellingham, WA 98226

Telephone: 360-594-4276

USING THE UNIT SAFELY

001

• Before using this unit, make sure to read the

instructions below, and the Owner’s Manual.

................................................................................................

002a

• Do not open or perform any internal modifi-

cations on the unit.

................................................................................................

003

• Do not attempt to repair the unit, or replace

parts within it (except when this manual

provides specific instructions directing you

to do so). Refer all servicing to your retailer,

the nearest Roland Service Center, or an

authorized Roland distributor, as listed on

the "Information" page.

................................................................................................

004

• Never use or store the unit in places that are:

• Subject to temperature extremes (e.g.,

direct sunlight in an enclosed vehicle, near

a heating duct, on top of heat-generating

equipment); or are

• Damp (e.g., baths, washrooms, on wet

floors); or are

• Humid; or are

• Exposed to rain; or are

• Dusty; or are

• Subject to high levels of vibration.

................................................................................................

007

• Make sure you always have the unit placed

so it is level and sure to remain stable. Never

place it on stands that could wobble, or on

inclined surfaces.

................................................................................................

010

• This unit, either alone or in combination with

an amplifier and headphones or speakers,

may be capable of producing sound levels

that could cause permanent hearing loss. Do

not operate for a long period of time at a high

volume level, or at a level that is uncom-

fortable. If you experience any hearing loss or

ringing in the ears, you should immediately

stop using the unit, and consult an audiol-

ogist.

................................................................................................

011

• Do not allow any objects (e.g., flammable

material, coins, pins); or liquids of any kind

(water, soft drinks, etc.) to penetrate the unit.

................................................................................................

012d

• Immediately turn the power off, and request

servicing by your retailer, the nearest Roland

Service Center, or an authorized Roland

distributor, as listed on the "Information"

page when:

• Objects have fallen into, or liquid has been

spilled onto the unit; or

• The unit has been exposed to rain (or

otherwise has become wet); or

• The unit does not appear to operate

normally or exhibits a marked change in

performance.

................................................................................................

013

• In households with small children, an adult

should provide supervision until the child is

capable of following all the rules essential for

the safe operation of the unit.

................................................................................................

Used for instructions intended to alert

the user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic

animals or pets.

Used for instructions intended to alert

the user to the risk of death or severe

injury should the unit be used

improperly.

The ● symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In

the case of the symbol at left, it means that the power-

cord plug must be unplugged from the outlet.

The symbol alerts the user to important instructions

or warnings.The specific meaning of the symbol is

determined by the design contained within the

triangle. In the case of the symbol at left, it is used for

general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never

be carried out (are forbidden). The specific thing that

must not be done is indicated by the design contained

within the circle. In the case of the symbol at left, it

means that the unit must never be disassembled.

3

014

• Protect the unit from strong impact.

(Do not drop it!)

................................................................................................

023

• DO NOT play a CD-ROM disc on a conven-

tional audio CD player. The resulting sound

may be of a level that could cause permanent

hearing loss. Damage to speakers or other

system components may result.

................................................................................................

104

• Try to prevent cords and cables from

becoming entangled. Also, all cords and

cables should be placed so they are out of the

reach of children.

................................................................................................

106

• Never climb on top of, nor place heavy

objects on the unit.

................................................................................................

108c

• Disconnect all cords coming from external

devices before moving the unit.

................................................................................................

118

• Should you remove the optical connector

caps, make sure to put them in a safe place

out of children's reach, so there is no chance

of them being swallowed accidentally.

................................................................................................

204

* Microsoft and MS-DOS are registered trademarks of

Microsoft Corporation.

205

* Microsoft, Windows, and Windows NT are regis-

tered trademarks of Microsoft Corporation.

206b

* Windows® 95 is known officially as: “Microsoft®

Windows® 95 operating system.”

206c

* Windows® 98 is known officially as: “Microsoft®

Windows® 98 operating system.”

206d

* Windows NT® is known officially as: “Microsoft®

Windows NT® operating system.”

???

* Windows Me® is known officially as: “Microsoft®

Windows ® Millennium version operating system.”

206e

* Screen shots reprinted with permission from

Microsoft Corporation.

206f

* Windows® 2000 is known officially as: “Microsoft®

Windows® 2000 operating system.”

207

* Apple is a registered trademark of Apple Computer,

Inc.

208

* Macintosh is a registered trademark of Apple

Computer, Inc.

209

* MacOS is a trademark of Apple Computer, Inc.

213

* Pentium is a registered trademark of Intel Corpo-

ration.

214

* MMX is a trademark of Intel Corporation.

220

* All product names mentioned in this document are

trademarks or registered trademarks of their

respective owners.

985

• The explanations in this manual include illustrations

that depict what should typically be shown by the

display. Note, however, that your unit may incor-

porate a newer, enhanced version of the system (e.g.,

includes newer sounds), so what you actually see in

the display may not always match what appears in

the manual.

4

IMPORTANT NOTES

In addition to the items listed under “USING THE UNIT

SAFELY” on page 2, please read and observe the follow-

ing:

Power Supply

• Before connecting this unit to other devices, turn off the

power to all units. This will help prevent malfunctions and/

or damage to speakers or other devices. (It is not necessary

to turn off the power of your computer.)

Placement

• Using the unit near power ampliﬁers (or other equipment

containing large power transformers) may induce hum. To

alleviate the problem, change the orientation of this unit; or

move it farther away from the source of interference.

• This device may interfere with radio and television recep-

tion. Do not use this device in the vicinity of such receiv-

ers.

• Do not expose the unit to direct sunlight, place it near

devices that radiate heat, leave it inside an enclosed vehi-

cle, or otherwise subject it to temperature extremes. Exces-

sive heat can deform or discolor the unit.

• To avoid possible breakdown, do not use the unit in a wet

area, such as an area exposed to rain or other moisture.

Maintenance

• For everyday cleaning wipe the unit with a soft, dry cloth

or one that has been slightly dampened with water. To

remove stubborn dirt, use a cloth impregnated with a mild,

non-abrasive detergent. Afterwards, be sure to wipe the unit

thoroughly with a soft, dry cloth.

• Never use benzine, thinners, alcohol or solvents of any

kind, to avoid the possibility of discoloration and/or defor-

mation.

Additional Precautions

• Use a reasonable amount of care when using the unit’s but-

tons, sliders, or other controls; and when using its jacks and

connectors. Rough handling can lead to malfunctions.

• When connecting / disconnecting all cables, grasp the con-

nector itself—never pull on the cable. This way you will

avoid causing shorts, or damage to the cable’s internal ele-

ments.

• To avoid disturbing your neighbors, try to keep the unit’s

volume at reasonable levels. You may prefer to use head-

phones, so you do not need to be concerned about those

around you (especially when it is late at night).

• When you need to transport the unit, package it in the box

(including padding) that it came in, if possible. Otherwise,

you will need to use equivalent packaging materials.

• Use a cable from Roland to make the connection. If using

some other make of connection cable, please note the fol-

lowing precautions.

• Some connection cables contain resistors. Do not use

cables that incorporate resistors for connecting to this

unit. The use of such cables can cause the sound level to

be extremely low, or impossible to hear. For information

on cable speciﬁcations, contact the manufacturer of the

cable.

• Before you open the included CD-ROM, you must read the

“license agreement." Opening the CD-ROM will be taken

to mean your acceptance of the license agreement.

Handling CD-ROMs

• Avoid touching or scratching the shiny underside (encoded

surface) of the disc. Damaged or dirty CD-ROM discs may

not be read properly. Keep your discs clean using a com-

mercially available CD cleaner.

UA-3 5

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

You must read this before you use digital recording

Unauthorized recording, distribution, sale, lending, public performance, broadcasting, or the like, in whole or

in part, of a work (musical composition, video, broadcast, public performance, or the like) whose copyright is

held by a third party is prohibited by law.

When exchanging audio signals through a digital connection with an external instrument, this unit can perform

recording without being subjected to some of the restrictions of the Serial Copy Management System (SCMS).

This is because the unit is intended solely for musical production, and is designed not to be subject to restrictions

as long as it is used to record works (such as your own compositions) that do not infringe on the copyrights of

others. (SCMS is a feature that prohibits second-generation and later copying through a digital connection. It

is built into MD recorders and other consumer digital-audio equipment as a copyright-protection feature.)

Do not use this unit for purposes that could infringe on a copyright held by a third party. Roland assumes no

responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use

of this unit.

This device does not support digital audio signals that are formatted for broadcast studio digital audio devices.

On the UA-3

The UA-3 will function with partial SCMS support only for a digital input signal from an external device. When

data containing SCMS ﬂags is input, for example from a MD that was digitally copied from a commercial music

CD, the UA-3 will function as follows.

If input from the UA-3’s digital input connector:

• The UA-3 cannot record this data to your computer

• The audio will be output from the analog outputs (line output jacks, headphone jack) and digital output con-

nector.

If input from the UA-3’s analog inputs (line input jacks):

• Recording can occur normally

Regardless of the presence or absence of the SCMS ﬂag, data that is received at the digital input

connector of the UA-3 will be output directly from the digital output connector.

The UA-3 operates according to SCMS only for digital input signals from an external device.

SCMS ﬂags are not added to the digital audio signals that are output from the UA-3.

Introduction

6

Introduction

Check the contents of the package

The UA-3 includes the following items. When you open the package, first make sure that all items are included. If any

are missing, contact the dealer where you purchased the UA-3.

UA-3

USB cable

Use this to connect the UA-3 to the USB connector of your computer. For details on connections, refer to Connec-

tions and driver installation (Windows p. 8, Macintosh p. 17).

AUDIO Capture CD-ROM

This contains software that you will need in order to use the UA-3.

* Be sure to read the Readme_E.txt file found in the AUDIO Capture CD-ROM. Any updated information will be provided in

the Readme_E.txt file.

Getting Started

This is the document you are reading. Keep it at hand for reference when needed.

License agreement

This contract describes the terms under which Roland Corporation allows you to use the software. You must read this

before opening the CD-ROM package.

You will need to provide these items yourself

External amp, speakers, headphones, and mic are not included

External amp, speakers, or headphones necessary for listening to the sound output via the UA-3 are not included. Nor

is a mic included for inputting sound to the UA-3. You will need to provide these items yourself.

Digital input/output cables for connecting the MD or DAT recorder are not included

Although you can use an MD or DAT digital recorder to perform digital recording, the cables for connecting the re-

corder to the UA-3 are not included. You will need to provide these separately.

Use only the included USB cable.

• Before opening the included CD-ROM, you must read the separate license agreement.

• Do not touch the silver recording surface of the disc, or scratch it. Doing so may make it impossible for data to be

read correctly. If the disc becomes soiled, use a commercially available CD cleaner to clean it.

• Do not play back the CD-ROM on a conventional audio CD player. Doing so will produce a high volume that

may damage your ears or speakers.

Introduction

UA-3 7

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

Parts of the UA-3 and their function

Mic input jack

Line input jacks

Line output jacks

Digital input connector (optical)

Digital output connector (optical)

USB connector

Mic type select switch

Set this switch according to a type of mic that is connected to the Mic input jack .

When connecting a dynamic mic: “DYNAMIC”

When connecting a condenser mic: “CONDENSER”

Recording input select switch

This selects the input that will be used for recording.

Digital input connectors : “DIGITAL”

Mic input jack / Line input jacks / Guitar input jack :“INPUT + GUITAR/MIC”

USB indicator

This will light when the UA-3 is connected and recognized to the computer.

Output level indicator

The number of LED’s that light changes according to the output level from the Headphone jack and the Line

output jacks . If the red LED lights, use the Line output volume to lower the volume.

Line output volume

This adjusts the volume that is output from the Headphone jack and the Line output jacks .

Guitar/Mic input peak indicator

If the input level from the Guitar input jack and the Mic input jack is excessive, it will light red. If it lights

red, use the Guitar/Mic input adjustment slider to lower the input level.

Guitar/Mic input adjustment slider

This slider adjusts the input level of the Guitar input jack and the Mic input jack .

Guitar input jack

Line input adjustment slider

This slider adjusts the input level of the Line input jacks .

Line input peak indicator

If the input level from the Line input jacks is excessive, it will light red.

If it lights red, use the Line input ad-

justment slider to lower the input level.

Headphone jack

A set of headphones can be connected here. Even if headphones are connected, sound will still be output from the Line

output jacks .

* For details on how each control and connector are actually used, refer to UA-3 Application Guide (p. 110).

• Condenser Mic

The UA-3 supports small multimedia microphones

used for adding narration, and is compatible with plug-

in powered monaural microphones.

• If you are recording only from the line inputs, dis-

connect the cables from the Guitar input jack and

the Mic input jack.

• The UA-3 is not compatible with the phantom-pow-

ered, condenser microphones typically used for music.

It is also incompatible with the stereo microphones

sometimes supplied with MDs.

• You cannot play back computer audio data when

DIGITAL is selected.

1

2

3

45 6

7

12

13 14 1716

15

8

9

10

11

1

2

3

4

5

6

7

1

8

4

1 2

14

9

10

17

3

11

17

3

12

14

1

13

14

1

14

15

2

16

2

15

17

3

Connections and driver installation (Windows)

8

Connections and driver installation (Windows)

* If you are a Macintosh user, refer to p. 17.

In order to use the UA-3, you must first install the USB Composite Device driver, the USB Human Interface

driver, and the USB Audio Device driver consecutively. These drivers are included with Windows. If you are using

Windows 98, this driver is provided in the Microsoft Windows CD-ROM, so you will need to have the Microsoft

Windows CD-ROM ready. If you are using Windows Me or 2000, the CD-ROM is not necessary.

What is a driver?

A driver is software that allows an application program running on your computer to transfer data to and from the UA-

3 when it is connected to your computer via a USB cable. The driver passes data from the application to the UA-3, and

passes data from the UA-3 to the application.

Making connections and installing the driver

■ Making connections

Always make sure to have the volume level turned down before connecting the UA-3. Even with the volume all the

way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a

malfunction.

To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the

power of all devices before making any connections. (It is not necessary to turn off the power of your computer.) Use

a USB cable to connect the UA-3 to your computer before turning on the power of your audio equipment.

Before installing the driver

• The UA-3 cannot be used with Windows 95 or Windows NT.

• If other Windows programs are running, exit all of them

before you continue.

• If you will be simultaneously connecting multiple Roland USB

devices (for example; the UA-3 and other USB devices such as the

UA-100G) to your computer, disconnect the UA-100G or other

devices from the USB connector before installing the driver. If you

install the driver when the UA-100G or other devices are con-

nected, installation may not occur correctly.

• Before disconnecting the USB cable or restarting

Windows, please close all applications. You should

also turn down the volume of any audio or amp sys-

tem that is connected.

• This unit is equipped with a protection circuit. A

brief interval (a few seconds) after connecting a

USB connector is required before the unit will

operate normally.

UA-3

Application

USB

Driver

USB port

USB cable

Computer

UA-3

Stereo Set

Powered Speaker etc.

LINE IN, AUX IN

Audio

cable

USB cable

* Connect after starting

up the computer

Computer

USB

port

USB

port

LINE OUT

Stereo

Headphones

Connections and driver installation (Windows)

UA-3 9

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

■ Installing the driver (Windows Me)

* If you are using a Windows 2000 machine, refer to p. 9, if Windows 98, refer to p. 9.

1. Turn on the power of your computer and start up Windows, and use a USB cable to connect the UA-3 to your

computer.

2. When Windows detects the UA-3 and the Add New Hardware Wiz-

ard dialog box appears, make sure “Automatic search for a better

driver (Recommended)” is selected, then click [Next].

3. The search for the driver starts.

4. When the correct driver is found, driver installation starts.

5. When a dialog box informing you that driver installation has ﬁnished

appears, click [Finish], and restart Windows.

After installing the driver, refer to Specifying the audio input/output device (p. 12) and select the device Windows uses.

* Depending on your computing setup, there may be a short wait after the driver is installed until the

device is recognized.

■ Installing the driver (Windows 2000)

* If you are using a Windows Me machine, refer to p. 9, if Windows 98, refer to p. 9.

1. Turn on the power of your computer and start up Windows.

2. Use a USB cable to connect the UA-3 to your computer.

The UA-3 is recognized to the computer and the driver is installed all automatically.

3. After installing the driver, restart Windows.

■ Installing the driver (Windows 98)

* If you are using a Windows Me machine, refer to p. 9, if Windows 2000, refer to p. 9.

Installation must be performed in the order of the USB Composite Device driver, USB Human Interface De-

vice driver, and then the USB Audio Device driver. Use the following procedure to perform the installation.

1. Turn on the power of your computer and start up Windows. Insert the Microsoft Windows CD-ROM into your

CD-ROM drive, and use a USB cable to connect the UA-3 to your computer (p. 8).

Some time may be required until this dialog box appears

Since some computers are sold with the contents of the Microsoft Windows CD-ROM already

in the hard disk, a Microsoft Windows CD-ROM may not have been included. If this is the case,

you will be able to install the driver without the Microsoft Windows CD-ROM

Connections and driver installation (Windows)

10

A USB Composite Device will be detected automatically, and the Add

New Hardware Wizard dialog box will appear. Click [Next].

2. When the display asks “What do you want Windows to do?”,

select “Search for the best driver for your device. (Recom-

mended).” and click [Next].

3. The following dialog box will appear. Check CD-ROM drive, and

click [Next].

4. The following dialog box will appear. Click [Next].

*

Depending on your system, the

Location of driver

may differ from the above

illustration, but this is not a problem.

5. Copying of the ﬁle (Driver) will begin.

If this dialog box does not appear, refer to Problems related to the

USB driver (p. 21)

If the Microsoft Windows CD-ROM is not inserted in the CD-ROM drive, the following dialog

box may appear. If this occurs, insert the Microsoft Windows CD-ROM into the CD-ROM

drive, and click [OK].

Connections and driver installation (Windows)

UA-3 11

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

6. When installation of the USB Composite Device driver is ﬁn-

ished, the following dialog box will appear. Click [Finish].

7. Then, the USB Human Interface Device will automatically be

detected, and the Add New Hardware Wizard dialog box will

appear. Click [Next], and continue the installation using the very

same procedure as steps 2-5 (p. 10-10).

8. When installation of the USB Human Interface Device driver is

ﬁnished, the following dialog box will appear. Click [Finish].

9. Next, a USB Audio Device will be detected automatically, and

the Add New Hardware Wizard dialog box will appear. Click

[Next], and continue the installation using the very same proce-

dure as in steps 2-5 (p.10-10).

10.When installation of the USB Audio Device driver is ﬁnished,

the following dialog box will appear. Click [Finish].

This completes installation of the USB Composite Device driver, the USB Human Interface Device driver, and

the USB Audio Device driver. Restart Windows.

After installing the driver, refer to Specifying the audio input/output device (p. 12) and select the device Win-

dows uses.

In step 4, the screen will indicate “Windows driver file search for

the device : USB Human Interface Device.”

In step 4, the screen will indicate “Windows driver file search for

the device : USB Audio Device.”

Connections and driver installation (Windows)

12

■ Specifying the audio input/output device

1. Click the Windows [Start] button, and select [Settings] - [Control Panel].

2. Win 98 / Win 98SE

In Control Panel, double-click the [Multimedia] icon to open the Multimedia Properties dialog box.

Win 2000 / Me

In Control Panel, double-click the [Sounds and Multimedia] icon to open the Sounds and Multimedia

Properties dialog box.

* If you don’t find a [Sounds and Multimedia] icon, then in Control Panel, click [view all Control

Panel options].

3. Click the [Audio] tab.

4. For the Playback item Preferred device, click . In the list that appears, click [USB Audio Device] to

select it.

5. For the Recording item Preferred device, click . In the list that appears, click [USB Audio Device]

to select it.

Windows 98 / Windows 98SE

Windows 2000 /Windows Me

6. Click [OK] to complete the settings.

Volume Control settings

The output volume of the UA-3 can be controlled by the Windows Volume Control.

1. Click the Windows [Start] button, and select [Programs] - [Accessories] - [Entertainment] - [Volume

Control] to start it up.

Windows Me Windows 2000/

Windows 98/Windows 98SE

• Depending on your system, “USB

Audio Device” will be shown a

number added, ex. “USB Audio

Device (1).”

• It will not be possible to press

the “Advanced Properties”

button for “Recording.”

Connections and driver installation (Windows)

UA-3 13

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

2. You can raise or lower the slider to adjust the volume of the UA-3. The following items can be set.

Checking for sound output

After the connections have been made correctly, you can play back the sample data to check your setup.

■ Playing the sample data

Here we will use standard Windows functionality to play the sample data. The sample data is found in the AUDIO

Capture CD-ROM. Insert the CD-ROM into the CD-ROM drive of your computer.

1. Copy “Alright(.wav)” to the desktop by dragging it from the “Sample_Data” folder of the CD-ROM.

USB Audio (Speaker) Adjust the volume of the analog outputs (line output

and headphone output). The digital output will not

change.

1

1. Depending on the version of Windows, this may be displayed as “Analog con-

nector”.

WAVE Adjust the volume that is output from the audio output

device “USB Audio Device.” The digital output and

analog output will change.

SW Synth Adjust the volume of the software synthesizer built into

Windows.

CD Player Adjust the “CD Music” volume for the CD-ROM drive

of your computer.

2

2. If the playback of the CD does not change when you adjust this volume, change

the WAVE volume.

• If Volume Control is not installed on your computer, use Add/ Remove Applications in the Control

Panel to install it. For details on installation, refer to the Windows owner’s manual or Help.

• If Mute is checked, or if the slider is in the lowest position, no sound will be output from the UA-3.

• If you are using Windows 2000 and “CD Player” does not appear, check the [Digital CD playback] item “Enable

digital CD audio for this CD-ROM device,” as described in the following note.

• When using your computer’s CD-ROM drive to play an audio CD, or when playing background music for games

with the UA-3

If using Windows Me:

Select [Start]-[Settings]-[Control Panel]. In the [Control Panel], double-click the [System] icon to

access the System Properties dialog box. Click the [Device Manager] tab, and double-click the

[CDROM] icon. Below it, double-click the CD-ROM drive that you are using and open its Properties.

Click the [Properties] tab, and select the check box located beside the Digital CD playback item

“Enable digital CD audio for this CD-ROM device.”

If using Windows 2000

In the same way as for Windows Me, open the System Properties dialog box. Click the [Hardware tab],

and click the [Device Manager] button to open the Device Manager. From the CD-ROM drives, double-

click the CD-ROM drive that you are using to open its Properties. Click the [Properties] tab, and select

the check box located beside the Digital CD playback item “Enable digital CD audio for this CD-ROM

device.”

If using Windows 98 or Windows 98 SE:

Select [Start] - [Settings] - [Control Panel] - [Multimedia], then click on the [CD Music] tab, then check

“Enable CD digital audio for this CD-ROM device.”

Depending on your computing environment, playback of these CDs may still be impossible. For details,

refer to information provided by your computer’s manufacturer. If you are using a PC-card (PCMCIA)

type CD-ROM drive, playing back WAVE data or an audio CD on the CD-ROM drive may cause the

sound to be interrupted, or no sound may be heard at all.

• The audio quality of the UA-3 will be better if you raise the Volume Control levels.

In order to listen to the sample data, you will need approximately 30MB of free space on the

hard disk where Windows installed.

Connections and driver installation (Windows)

14

2. Right-click the copied ﬁle “Alright(.wav)”, and select [Play] or [Properties] from the menu

that appears.

3. Click the [Preview] tab, and then click the button.

The sample data will begin playing.

Did you hear the sample data?

If the sample data played correctly, your computer and the UA-3 are connected correctly, and the drivers have been

installed correctly. If the data did not play correctly, refer to Troubleshooting (p. 21). Troubleshooting contains mate-

rial to help you find and correct such problems.

This completes all connections and driver installation for the UA-3.

Deleting the USB Audio Device driver

■ If re-installing the USB Audio Device driver

■ If installation of the USB Audio Device driver was terminated before completion

Use the following procedure to delete the driver that is already installed.

1. Use a USB cable to connect the UA-3 to your computer.

2. Click the Windows [Start] button, and select [Settings] - [Control Panel].

3. In

[Control Panel]

, double-click [System] to open the System Properties dialog.

4. Click the [Device Manager] tab.

5. Double-click [Sound, video and game controllers] to see a list of the devices.

6. From the list, select USB Audio Device, and click [Remove]. In the Conﬁrm Device Removal dialog box,

click [OK]. If USB Audio Device is not displayed, proceed to step 8.

7. Make sure that USB Audio Device is not in the Sound, video and game controllers list, and click

[Close] to close the System Properties dialog.

8. Follow the steps 1. – 4. again, and double-click [Universal Serial Bus controllers] to display the list of

devices.

If is displayed for the USB-compatible device icon:

Select the [USB Composite Device] icon, and click [Remove]. In the Conﬁrm Device Removal dialog

box, click [OK]. As in the step 7., close System Properties.

If there is no USB-compatible device icon, or if is not displayed:

Simply close System Properties.

If you are using Windows Me and is displayed:

Simply close System Properties.

When the Recording input select switch is set to DIGITAL, it is

not possible to play back audio data from your computer. Set the

switch to INPUT + GUITAR/MIC.

The explanation provided here is for an average Windows system. Depending on your com-

puter, some of the folder names may be different.

Connections and driver installation (Windows)

UA-3 15

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

9. Disconnect the USB cable from your computer, and restart Windows.

Basic operation of the D-Out Smoother

■ What is the D-Out Smoother?

When audio is played back to a digital device such as MD or DAT connected to the digital output of the UA-3, a certain

amount of time is required for the audio output to be locked immediately after audio playback, so that there may be no

sound for one or two seconds, or the pitch or tempo may become incorrect. The D-Out Smoother is software that allows

the audio to be played smoothly in such situations.

■ Installing the D-Out Smoother

1. Insert the AUDIO Capture CD-ROM into your CD-ROM drive.

2. Click the Windows [Start] button, and select [Run...].

3. In the Open: text box, input “E:\UA_Util\Setup.exe” and click [OK]. Alternatively, click [Browse], select the

ﬁle [Setup(.exe)] located in the UA_Util folder of the CD-ROM drive, and click [Open].

4. The installer will start up, and the Choose Setup Language dialog box will appear. Specify whether you are

using the “English (United States)” or “Japanese” version of Windows, and click [OK].

5. Perform the remainder of the installation as directed by the instructions that appear on-screen.

6. When installation is completed, the Setup Complete dialog box will appear. Click [Finish].

This completes installation of the D-Out Smoother.

■ Starting the D-Out Smoother

1. Connect the UA-3 to the USB connector of your computer.

2. Click the Windows [Start] button, and in the [Programs] menu, click [D-Out Smoother].

3. The D-Out Smoother will start up.

In some cases it may display“Cannot ﬁnd USB Audio Device. Check USB cable or select USB

Audio Device again.” when starting. If this occurs, the computer has not correctly detected the UA 3. It

is possible that the UA-3 is not connected correctly, or that the driver has not been installed correctly.

Refer to Connections and driver installation (Windows) (p. 8) and check these points.

■ Using the D-Out Smoother

The D-Out Smoother has an “ON/OFF” switch and a “TEST” button.

“ON/OFF” switch

Normally, you will leave this “ON” when using the digital output of the UA-3.

Turn this “OFF” when connecting or disconnecting the UA-3.

“TEST” button

Click the [TEST] button. If the test audio is heard, the D-Out Smoother is operating for that device.

When using two or more USB Audio Devices such as the UA-3 or MA-150U, use this button to select the UA-3

for which the D-Out Smoother will operate.

Use the following procedure to make your selection.

If a dialog box suggesting that you restart Windows appears at this point, follow the sugges-

tion and restart your computer.

In this explanation we are assuming that your CD-ROM drive is drive E:, but the drive name

may be different depending on your computer. If the drive name is different on your com-

puter, input the appropriate drive name. You can check the drive name of your CD-ROM

drive by double-clicking the My Computer icon.

The Setting dialog box will appear at the first time when you start up. Make sure that the

Wave-Out Device shows “USB Audio Device,” and click [OK]. If two or more USB audio

devices are displayed, refer to Using the D-Out Smoother (p. 15), and specify the correct device.

Connections and driver installation (Windows)

16

1. From the D-Out Smoother [Control] menu, select [Setting] to access the Setting dialog box. (This dialog box

will appear automatically the ﬁrst time the software is started up.)

2. From the pull-down menu, select “USB Audio Device” and click [OK].

3. Click the [TEST] button, and check whether or not the test audio is heard.

If the audio is heard, the D-Out Smoother is operating for that device. If the audio is not heard, select a different

USB Audio Device in step 2, and repeat steps 1 through 3.

■ Deleting (uninstalling) the D-Out Smoother

The D-Out Smoother supports the Windows Add/Remove Programs Properties function. You can use the fol-

lowing procedure to remove the program if it becomes unnecessary.

1. Click the Windows [Start] button, and select [Settings] - [Control Panel].

2. In

[Control Panel]

, double-click [Add/Remove Programs] to open the Add/Remove Programs Proper-

ties dialog box.

3. Click the [Install/Uninstall] tab.

4. From the list in the dialog box, click the name of the application that you wish to delete.

5. Click [Add/Remove].

The application you specified in step 4 will be deleted.

Convenient Features

• When [Register to STARTUP] is checked in the Setting dialog, D-Out Smoother will automatically start up

when you start up the computer.

• When [Minimize window when starting up] is checked in the Setting dialog, D-Out Smoother will mini-

mize itself immediately after it starts up, allowing you to use your computer’s screen more effectively.

If you uninstall D-Out Smoother, you should firstly uncheck the [Register to STARTUP] in the

Setting dialog. You can go to the Setting dialog by selecting [Control] - [Setting]. (p. 25)

Connections and driver installation (Macintosh)

UA-3 17

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

Connections and driver installation (Macintosh)

* If you are a Windows user, refer to p. 8.

In order to use the UA-3, you must first install a driver. UA-3 uses a driver included with Mac OS.

Making connections and installing the driver

■ Making connections

(943)

Always make sure to have the volume level turned down before connecting the UA-3. Even with the volume all the

way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a

malfunction.

(921)

To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the

power of all devices before making any connections. (It is not necessary to turn off the power of your computer.) Use

a USB cable to connect the UA-3 to your computer before turning on the power of your audio equipment.

■ Getting the unit to be recognized

1. Turn on the power of your computer and start up Mac OS.

2. From the Apple menu, select the [Apple System Proﬁler].

3. Click the [Devices and Volumes] tab control.

4. Use a USB cable to connect the UA-3 to your computer.

What is a driver?

-> p. 8

• Before disconnecting the USB cable or restarting Mac-

intosh, please close all applications. You should also

turn down the volume of any audio or amp system

that is connected.

• This unit is equipped with a protection circuit. A brief

interval (a few seconds) after connecting a USB connector

is required before the unit will operate normally.

• To prevent damage to your speakers, turn down the volume on this unit, and on

any audio devices you may have connected.

• Make sure to quit all applications that may be running before you make

the connection.

UA-3

Stereo Set

Powered Speaker etc.

LINE IN, AUX IN

Audio

cable

USB cable

* Connect after starting

up the computer

Computer

USB

port

USB

port

LINE OUT

Stereo

Headphones

Connections and driver installation (Macintosh)

18

5. To make sure it is successfully recognized, select [Update all information] from the [Commands] menu. You should

see the following three audio devices in the USB section, as shown below:

If the indication is correct, the installation of the UA-3 driver is successful. Select [Quit] from the [File] menu to

close the Apple System Proﬁler dialog, then make the sound settings explained below.

If the indication is incorrect, you should try disconnecting the UA-3 from the USB port, and waiting about ten

seconds. Then, do the procedure over again, starting from the step 4.

■ Making the sound settings

6. From the Apple menu, select [Control Panels] - [Sound] to open

the Sound dialog.

7. Click the [Speakers] tab.

8. Turn down the volume on the UA-3, and on your audio equipment, then

click [Start Test].

9. Test sounds are output from left to right, along with what appears on the

screen; adjust the volume using the [Main Volume] bar. When you are

ﬁnished, click [Stop Test].

Depend on the your OS version, there is no [Main Volume] bar. In that

case, use the [Volume] bar in the [Output] to adjust the volume.

If the Recording input select switch is set to DIGITAL, it is not pos-

sible to play back audio data from your computer. Set the switch

to INPUT + GUITAR/MIC.

Connections and driver installation (Macintosh)

UA-3 19

DEUTSCHFRANÇAISESPAÑOLITALIANO ENGLISH

10.Select [Input] from the Sound dialog. Then, in Choose a source

for sound input:, choose USB Audio.

11.When you have ﬁnished making settings, select [Quit] from the [File] menu to close the Sound dialog.

Known issues: UA-3

• Some applications such as Cakewalk’s Metro Series and TC Work’s Spark Series cannot record/playback at 48

kHz. Please use the UA-3 at 44.1 kHz.

• While the audio application is recording or playing, do not connect/disconnect the USB cable, or move the

Recording input select switch.

Doing so may cause the application to freeze.

• You may hear sound hopping and/or noise when you record and play back at the same time due to high load on the

CPU. However, the noise should not be in the recording itself. Such noise should only be found in the playback

signal.

• If you are going to use the Virtual Sound Canvas 3, you will need to select [Performance] from the [Setting]

menu, and set the Expression Mode to Response Priority.

• The standard driver that comes with Mac OS is not ASIO compatible.

• When you start up your computer with the UA-3 connected, the computer may become unstable. If this occurs,

start up your computer before connecting the UA-3, and connect the UA-3 after start-up.

Checking for sound output

After the connections have been made correctly, you can play back the sample data to check your setup.

■ Playing the sample data

Here we will use standard Macintosh functionality to play the sample data. The sample data is found in the AUDIO

Capture CD-ROM. Insert the CD-ROM into the CD-ROM drive of your computer.

1. Copy “Alright” to the desktop by dragging it from the “Sample_Data” folder of the CD-ROM.

2. Launch QuickTime Player, which is provided with the Mac OS. The

QuickTime Player is normally located in the QuickTime folder within

the Applications folder of your hard disk.

• If you don’t see USB Audio, you should close the Sound dialog. Then, discon-

nect the UA-3, and wait about ten seconds. Then, try doing the procedure over

again, starting at number 2.

• Do not check [Play sound through output device].

In order to listen to the sample data, you will need approximately 30MB of free space on the

hard disk that contains your system.

Connections and driver installation (Macintosh)

20

3. From the [File] menu, select [Open Movie], select the copied ﬁle

“Alright,” and click [Convert] to open it.

4. Click the playback button.

The sample data will begin playing.

Did you hear the sample data?

If the sample data played correctly, your computer and the UA-3 are connected correctly, and the drivers have been

installed correctly. If the data did not play correctly, refer to Troubleshooting (p. 21). Troubleshooting contains mate-

rial to help you find and correct such problems.

This completes all connections and driver installation for the UA-3.

If the Recording input select switch is set to DIGITAL, it is not possible to play back audio

data from your computer. Set the switch to INPUT + GUITAR/MIC.

La pagina si sta caricando...

Roland UA-3 Manuale del proprietario

Roland UA-3 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti