Barco GRAPHICS 1208s Manuale utente
- Categoria
- Proiettori di dati
- Tipo
- Manuale utente
GRAPHICS
1208s
R9000893
R9000896
OWNER'S MANUAL
BARCO PROJECTION SYSTEMS
Date :
220197
Art. No. :
R5975847
GRAPHICS
1208s
R9000893
R9000896
OWNER'S MANUAL
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, January 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Table of Contents
i-1
5975847 BARCOGRAPHICS 1208S 220197
Table of contents ........................................................................................................................................................................... i
Safety instructions .....................................................................................................................................................................1-1
On safety.............................................................................................................................................................................1-1
On installation ..................................................................................................................................................................... 1-2
On servicing ........................................................................................................................................................................1-2
On cleaning ......................................................................................................................................................................... 1-2
On repacking .......................................................................................................................................................................1-2
On illumination.....................................................................................................................................................................1-2
Location and Functions of Control ........................................................................................................................................... 2-1
Rear panel terminology........................................................................................................................................................2-1
Front panel terminology .......................................................................................................................................................2-1
Control panel terminology ....................................................................................................................................................2-2
a. The Local Keypad............................................................................................................................................................2-2
b. RCU control panel terminology ........................................................................................................................................2-2
Connections ...............................................................................................................................................................................3-1
AC Power (mains) Cord Connection .................................................................................................................................... 3-1
Power Check .......................................................................................................................................................................3-1
Switching On/Off .................................................................................................................................................................3-1
Signal Input Connection to the Projector : ............................................................................................................................3-2
Connecting a Composite Video source to port 1. .................................................................................................................3-3
Connecting a S-Video or Video source to port 2. .................................................................................................................3-3
Connecting a RGB Analog source to port 3. ........................................................................................................................3-4
Connecting a RGB Analog source to port 4/5.......................................................................................................................3-4
Connecting a RGB Analog source with Tri-level sync to port 4/5.(option) ............................................................................. 3-5
Connecting a Component Video source to port 4/5. .............................................................................................................3-5
Connecting a Component Video source with Tri-level sync to port 4/5.(Opion)..................................................................... 3-5
Peripheral equipment...........................................................................................................................................................3-6
Connecting a RCVDS 05 switcher to the BARCOGRAPHICS 808s ..................................................................................... 3-6
Connecting a VS05 switcher to the BARCOGRAPHICS 808s. .............................................................................................3-6
Connecting an IR Remote Receiver to the BARCOGRAPHICS 808s ...................................................................................3-6
Controlling.................................................................................................................................................................................. 4-1
Battery installation in the RCU. ............................................................................................................................................4-1
How to use your RCU .......................................................................................................................................................... 4-2
Projector Address ................................................................................................................................................................ 4-2
How to display a projector address? ....................................................................................................................................4-3
How to program an address into the RCU? ..........................................................................................................................4-3
Input selection .....................................................................................................................................................................4-3
Analog Picture Controls .......................................................................................................................................................4-4
Controlling chained projectors. ............................................................................................................................................4-4
Start up of the Adjustment Mode .............................................................................................................................................. 5-1
Adjustment Mode ................................................................................................................................................................5-1
Random Access Adjustment Mode ........................................................................................................................................... 6-1
Starting-Up the Random Access Adjustment mode..............................................................................................................6-1
Overview 'Random Access Adjustment' mode .....................................................................................................................6-1
Selecting Setup Pattern .......................................................................................................................................................6-3
Internal Cross Hatch Pattern................................................................................................................................................ 6-3
Random access adjustment mode selection menu. ............................................................................................................. 6-4
Picture Tuning .....................................................................................................................................................................6-4
Color Balance......................................................................................................................................................................6-4
Sync Fast/Slow Adjustment .................................................................................................................................................6-5
Peaking ...............................................................................................................................................................................6-5
Clamp Tuning ......................................................................................................................................................................6-5
Port 2 : Video or S-Video .....................................................................................................................................................6-6
Line Doubler ........................................................................................................................................................................6-6
Color Select.........................................................................................................................................................................6-6
Focusing .............................................................................................................................................................................6-7
Focusing color select...........................................................................................................................................................6-7
Blue on source ....................................................................................................................................................................6-7
Geometry Adjustments ........................................................................................................................................................6-8
Horizontal Phase Adjustment...............................................................................................................................................6-8
Raster Shift Adjustment ....................................................................................................................................................... 6-9
Left-Right (east-west) Adjustments .................................................................................................................................... 6-10
Seagull correction.............................................................................................................................................................. 6-11
Left Side Correction...........................................................................................................................................................6-11
Top-Bottom (north-south) Adjustments .............................................................................................................................. 6-12
Seagull Correction ............................................................................................................................................................. 6-13
Horizontal Size Adjustment................................................................................................................................................ 6-13
Vertical Linearity Adjustment .............................................................................................................................................6-14
Vertical Size Adjustment....................................................................................................................................................6-14
Table of Contents
i-2 5975847 BARCOGRAPHICS 1208S 220197
Blanking Adjustments........................................................................................................................................................ 6-15
Convergence Adjustment .................................................................................................................................................. 6-16
Service mode ............................................................................................................................................................................. 7-1
Starting up the Service mode. ............................................................................................................................................. 7-1
Overview flowchart 'Service' mode. ..................................................................................................................................... 7-1
Identification........................................................................................................................................................................ 7-2
Copy a block ....................................................................................................................................................................... 7-2
Deletion of blocks................................................................................................................................................................ 7-3
Deleting block by block ....................................................................................................................................................... 7-3
Deletion of all blocks ........................................................................................................................................................... 7-3
Change password ............................................................................................................................................................... 7-4
Change Language............................................................................................................................................................... 7-4
Run time ............................................................................................................................................................................. 7-4
Set to midposition ............................................................................................................................................................... 7-5
Undo Midposition ................................................................................................................................................................ 7-5
Convergence Mid ................................................................................................................................................................ 7-5
Undo Convergence Mid(position) ........................................................................................................................................ 7-5
Dynamic Astigmatism (spot shape adjustment) ................................................................................................................... 7-6
G2 Adjust ............................................................................................................................................................................ 7-7
Gamma corrections ............................................................................................................................................................. 7-7
CRT run in cycle ................................................................................................................................................................. 7-7
Projector Warm Up.............................................................................................................................................................. 7-8
CRT Drive Mode ................................................................................................................................................................. 7-8
Messages, warnings and failures ............................................................................................................................................. 8-1
Options ....................................................................................................................................................................................... 9-1
Appendix A : Orbiting ...................................................................................................................................................................A-1
Appendix B : Adjsutment Blocks and Source Numbers 90-99 ......................................................................................................B-1
Safety Instructions
1-1
5975847 BARCOGRAPHICS 1208S 220197
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits
of a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commer-
cial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using
this unit.
* The safety and operating instructions manual should be retained for
future reference.
* All warnings on the equipment and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
Operating AC power voltage of the projector:
BARCOGRAPHICS 1208s
Art. No. R9000893 230V AC
Art. No. R9000896 120V AC
Consult your dealer to switch over from 230Vac to 120 Vac or from
120Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-
type power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
1
SAFETY INSTRUCTIONS
Notice on Safety
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against risk of electric shock and energy hazard,
and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual
thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed
by qualified BARCO personnel or by authorized BARCO
service dealers.
OWNER’S RECORD
The part number and serial number are located at the back side of the
projector. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your BARCO dealer regarding
this product.
PART NUMBER :
SER. NUMBER :
DEALER :
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point within a triangle is in-
tended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
Safety Instructions
1-2 5975847 BARCOGRAPHICS 1208S 220197
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in
accordance with the following code.
Green and yellow: earth (safety earth)
Blue: neutral
Brown: line (live)
B. Power cord with ANSI 73.11 plug
:
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White: neutral
Black: line (live)
3. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
4. If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
6. Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
On installation
1. Do not place this equipment on an unstable cart, stand, or table.
The product may fall, causing serious damage to it.
2
. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat
register.
The projector should not be placed in a built-in installation or enclo-
sure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the equipment.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating
instructions are followed.
Note : Adjust only those controls that are covered by the operating
instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts or
authorized replacement parts which have the same characteristics as
the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the product is in proper
operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
-
To keep the cabinet looking brand-new, periodically clean it with a
soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents,
such as thinner or benzine, or abrasive cleaners, since these will
damage the cabinet.
- To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coat-
ing, therefore, avoid touching the lens. To remove dust on the lens,
use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
On repacking
Save the original shipping carton and packing material; they will
come in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential
that the ambient light which is allowed to fall on the screen be kept to
an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are non-
reflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
Location and Functions of Control
2-1
5975847 BARCOGRAPHICS 1208S 220197
2
LOCATION AND FUNCTION OF CONTROLS
REAR PANEL TERMINOLOGY
Communication Port (800 peripherals)
* allows communication between the RCVDS switcher and
the projector.
* allows connection of a remote IR receiver unit to the
projector.
Port 3
RGB Analog Input (9 pin female sub D connector). Allows
a character generator, microcomputer, etc. having analog
RGB outputs to be connected to the projector.
Port 4/5 : RGB-S Input (5x BNC connector):
RGB-S input : allows a character generator, microcom-
puter, video camera, etc. having analog RGB output to be
connected to the projector.
Line inputs: - signals RED-GREEN-BLUE
- COMPOSITE sync. signal
- Tri level sync signal (option)
VIDEO Input (Composite video, 2x loop-through BNC
connector)
: allows a video tape recorder, video camera,
color receiver/monitor, etc. having video line output to be
connected to the projector.
75 ohm Termination Switch for Video signals
1
Projector Pilot Lamp : indicates the status of the projector.
- unlit : mains (power) switch is not pressed.
- lit : mains (power) switch is pressed and the indicated color
shows the projector mode:
Green color : operational mode of the projector.
Red color : standby mode of the projector.
Important : projector ("Operational" or "Standby") mode is
defined during the installation of the projector. (Refer to a
qualified technician for change).
S-VIDEO Input: Separated Y/C (luma-chroma) signal in-
puts and outputs for higher quality playback of Super VHS
signals (4-pin S-VIDEO connector loop-through).
75 ohm Termination Switch for S-Video signals
Power Switch :
press the switch to turn the projector ON.
Depending on the hardware set-up of the projector during
installation, the projector switches to
‘Standby’ or to ‘Op-
erational'
mode. If in standby, the standby LED lights up.
FRONT PANEL TERMINOLOGY
RS 232 Input Port
Connection between the projector and an IBM PC (or
compatible) or MAC (RS422) for remote computer control
and data communication.
RS 232 Output Port
RS 232 Input Port allows a communication link for PC or
MAC to the next projector in a series of projector.
IR Sensor
receiver for control signals transmitted from the RCU.
IR Remote
Connector for remote input for hard wired remote control
Power (mains) input
Connect the supplied ac power (mains) cord here and to
the wall outlet.
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
RGB
PORT 6
REMO TE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ONOFF
GREEN : operational
RED : stand-by
1
23
4
5
6
7
PORT 3
2
3
4
5
6
7
1
2
3
4
4
RS232 OUT
RS232 IN
IR
REMOTE
1
2 3
4
REMOTE
IR
RS232 OUT
RS232 IN
V NOM
I MAX
FREQ
120/230 Volt
7/5Amp
50/60Hz
5
685
Location and Functions of Control
2-2 5975847 BARCOGRAPHICS 1208S 220197
b. RCU control panel terminology
This remote control includes a battery powered infrared (IR) transmit-
ter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation
and set-up. It includes automatic storing of :
- picture controls (Brightness, Sharpness,....)
- picture geometry adjustments
- convergence adjustments
Other functions of the remote control are:
- switching between standby and operational modes
- switching to "pause" (blanked picture, full power for immediate
restarting)
- direct access to all connected sources
- variable adjustment speed : when pushing continuously on the
control stick or the picture keys, the adjustment will be executed in
an accelerated fashion.
stand-by
sharpness
pause/park
tint
color
brightness
contrast
Back light key : when activated, all keys will be lit up and
visible in the dark.
ADJ.
: adjust key, to enter or exit the adjustment mode.
Address key (recessed key), to enter the address of the
projector (between 0 and 9). Press the address key,
followed by pressing one digit button between 0 and 9.
STBY : stand by button :
- to initiate remote power up operation
- to stop projection without main power off.
Pause :to blank the image, press PAUSE. The image
disappears but full power is retained for immediate restart-
ing.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
level (see also 'Controlling') for each picture function.
TEXT : when adjusting one of the image controls during a
meeting, the displayed bar scale can be removed by press-
ing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key is only active in
operational mode. When 'TEXT' is off, no warning message
will be displayed.
1
2
3
4
5
6
7
8
-
+
-
+
-
+
-
+
-
+
0
9
7
8
6
5
43
21
ENTER
11
10
9
7
1
2
3
4
5
6
12
32c
PAUSE
8
TEXT
EXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
ENTER
: to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
9
10
Control stick key
: to make menu selections when in the
adjustment mode. Also allows to increment or decrement an
adjustment in the adjustment mode.
control stick forward = up arrow in the menus
control stick backward = down arrow in the menus
control stick to the right = arrow to the right on the menus
control stick to the left = arrow to the left on the menus
RC operating indication
: lights up when a button on the
remote control is pressed. (This is a visual indicator to check
the operation of the remote control)
11
12
Connections
3-1
5975847 BARCOGRAPHICS 1208S 220197
hm
ON
T 1
EO)
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
352
3
CONNECTIONS
AC Power (mains) Cord Connection
Use the supplied power cord to connect your projector to
the wall outlet. Plug the female power connector into the
male connector at the backside of the projector.
Power Check
Power voltage indication on sticker on the back side of the projector.
The power voltage is indicated by the art. no.
Warning !
Check if the indicated power voltage corresponds to that of the wall
outlet.
Art. No. R9000893 must be connected to a 230 VAC power source.
Art. No. R9000896 must be connected to a 120 VAC power source.
If the wall outlet voltage is different, call a qualified technician for
power adaptation of the projector.
Switching On/Off
The projector is switched ON and OFF using the power (mains) switch
ON/OFF.
Pressed : ON
Not pressed : OFF
The projector can start now in the 'operational mode' (image dis-
played) or in the 'stand by mode', depending on the position of the
'power up' dip switch on the controller unit. This DIP switch must be
set during installation by a qualified technician. If you want to change
this start up mode, call a qualified technician.
Stand by indication lamp :
no light up : projector switched off
green color : projector in Operational mode
red color : projector is in Standby mode.
RS232 OUT
RS232 IN
IR
REMOTE
REMOTE
IR
RS232 OUT
RS232 IN
V NOM
I MAX
FREQ
120/230 Volt
7/5Amp
50/60Hz
685
Connections
3-2 5975847 BARCOGRAPHICS 1208S 220197
PROJECTOR WARM UP
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES.
FOR IMMEDIATE USE OF
THE PROJECTOR, PRESS
<EXIT>.
WARNING : SKIPPING THIS
PROCEDURE CAN REDUCE
THE INITIAL PICTURE
QUALITY OF THE PROJECTED
IMAGE.
THIS OPTION CAN BE
DISABLED IN THE SERVICE
MENU
When starting up the projector, with the power switch or via the stand-by key, the
projector can start up in two ways if the "CRT run in" cycle option is switched OFF.
- full white image (projector warm up) or
- immediately image display.
The way of starting up can be set in the service mode.
Start up with full white image.
The next menu will be displayed for 30 seconds.
a. Start up with warm up period.
If no action is taken, a white image will be displayed for 20 minutes.
This white image will be shifted on the faceplate of the CRT to avoid a CRT burn in.
During this warm up period, it is possible to interrupt this white image projection by
pressing the EXIT key. The previous menu will be repeated for another 30 seconds but
the remaining time will be indicated.
If EXIT is pressed, the remaining warm up period will be shipped.
REMAINING
PROJECTOR
WARM UP
TIME
18.5MIN
PLEASE USE
<EXIT> TO
LEAVE THIS
PROCEDURE
During the warm up period, every 30 seconds a text box with the remaining time will
be displayed on the screen for 2 seconds. This text box will be displayed every time
on another place.
If another key, different from EXIT, is pressed, a text box with following text will be
displayed :
Please use <EXIT> to leave this procedure.
b. Start up without warm up period.
If the
EXIT
key is pressed, the warm up period will be skipped and the projector is
immediately ready for use.
Warning : skipping this warm up procedure can reduce the initial picture quality
of the projected image.
Signal Input Connection to the Projector :
- Composite Video
- S-Video
- RGBS or RGsB
- RGB3S or RG3sB (option)
Only available when the optional Tri-level sync module is installed.
Port No Projector input Press Digit Button
1 Comp. Video 1
2 S-Video
1
/Comp. Video* 2
3 RGB
2
3
4/5 RGB
2
4 or 5
4/5 Component video
3
6
4/5 RGB with Tri level sync
4
7
4/5 Component video
with Tri-level sync
5
8
1
Input signal Y/C (luma/chroma)
2
Input signal : R, G and B with automatic sync
detection between seperate sync (separate com-
posite sync or with separate Hor and Vert. sync)
or sync on green (composite sync).
3
Input signal : R-Y, Y and B-Y with separate
composite sync or with separate Hor and Vert.
sync or with composite sync on Y.
4
Input signal : R, G and B with separate Tri level
sync or with Tri-level sync on green.
5
Input signal : R-Y, Y and B-Y with separate Tri
level sync or with composite Tri-level sync.
* Video or S-Video : switchable in the Picture
Tuning menu.
75 ohm
OFF
ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
GB
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
357
5
34
1
2
PORT 3
Connections
3-3
5975847 BARCOGRAPHICS 1208S 220197
Connecting a Composite Video source to port 1.
Video input selection :
with the RCU or the build in RCU : press digit button 1
* Note : if using the loop-through Video output, then set the
Termination Switch to the "OFF" position.
Connecting a S-Video or Video source to port 2.
Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.
Highlight Port 2 : Video and press ENTER to toggle between VIDEO
or S-VIDEO.
Press EXIT to return.
Press ADJUST to return to operational mode.
Select with or
then <ENTER>
<EXIT> to return.
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 02
Select with or
then <ENTER>
<EXIT> to return.
Choose a setup pattern
from below :
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 02
Select with or
then <ENTER>
<EXIT> to return.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with or
<ENTER> to accept
<EXIT> to return.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT2 : S-VIDEO
LINE DOUBLER : ON
Highlight 'Picture Tuning' and press ENTER.
Select 'Selected source' and press
ENTER.
Input selection
with the RCU or the build in RCU : press digit button 2
Depending on the priority setting in the Picture Tuning
menu, Video or S-Video can be displayed.
If the setting is not correct, start up the adjustment mode by
pushing on th
ADJUST key.
Select 'Random Access' and press
ENTER.
* Note: When using the Port 2 loop-through output, set the Termina-
tion Switch in the "OFF" position.
1
2
3
4
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp ±3dB
Pin 4: chrominance signal(C)
300mVpp ±3dB
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
G
B
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
358
TV tuner, e.g. TVDM40 stereo
VCR
Audio amplifier
Composite
video
to next projector or
to a monitor
Composite video signals from a VCR, OFF air signal
decoder, etc..
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
GB
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
359
VCR S-VHS
Audio amplifier
Luma/Chroma
to next projector or
to a monitor
Connections
3-4 5975847 BARCOGRAPHICS 1208S 220197
Connecting a RGB Analog source to port 3.
Connect your RGB source via an interface to Port 3.
Always use an interface when a computer and local monitor have to
be connected to the projector.
Barco interfaces which can be applied :
Universal analog interface R9826100
RGB 120 MHz analog interfaceR9826570
VGA interface 120V R9828079
230V R9828070
MAC interface 120V R9828059
230V R9828050
MAGIK interface 120V R9828129 & R9828128
230V R9828120 & R9828121
RGB analog input with automatic sync detection. (Separate H and
V sync inputs, with composite sync input or with sync signals on
green)
Pin configuration D9 connector of the Analog input.
1 not connected
2 ground RGBS
3 RED
4 GREEN
5 BLUE
6 ground RGBS
7 ground RGBS
8 Hor/comp. sync
9 Vert. sync
Analog Input Selection :
with the RCU or build in RCU, press digit button 3.
Connecting a RGB Analog source to port 4/5.
RGB analog input terminals with separate H and V sync inputs, with
composite sync input or with sync signals on green (automatic sync
detection).
Always use an interface when a computer and local monitor have to
be connected to the projector. See 'Connecting a RGB Analog
source to port 3' for a list of BARCO interfaces which can be applied.
RGB input selection :
(RGB : R, G, B signals with automatic sync detection)
with the RCU or the build in RCU : press digit
button 4 or 5
75 ohm
OFF
ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
G
B
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
INP
INP
R
G
BH
V
INPUT
ANALOG INTERF. 120MHz
ON
OFF
inver.
75 ohm term.
361
75 ohm
OFF
ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
GB
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ONOFF
GREEN : operational
RED : stand-by
INP
INP
R
G
B
H
V
INPUT
ANALOG INTERF. 120MHz
ON
OFF
inver.75 ohm term.
363
Connections
3-5
5975847 BARCOGRAPHICS 1208S 220197
Connecting a RGB Analog source with Tri-level
sync to port 4/5.
(option)
RGB analog input terminals with Tri level sync input or
with Tri-level sync on green. The projector detects
automatically where the sync signal is located.
RGB input selection :
(RG3sB : R, G, B signals with automatic Tri-level sync detection)
with the RCU or the build in RCU : press digit button 7
Connecting a Component Video source to
port 4/5.
A component video (R-Y, Y, B-Y) with sync signals can be connected
to the projector via the Port 4/5. The projector detects automatically
where the sync signal is located.
To select the component video input :
with the RCU or the build in RCU : press digit button 6.
To select the component video input :
with the RCU or the build in RCU : press digit button 8.
Connecting a Component Video source with Tri-
level sync to port 4/5.
(Opion)
A component video (R-Y, Y, B-Y) with Tri-level sync signals can be
connected to the projector via the Port 4/5. The projector detects
automatically where the sync signal is located.
798
VCR HDTV player
Audio amplifier
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
G
B
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
798
VCR HDTV player
Audio amplifier
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
G
B
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
798
VCR HDTV player
Audio amplifier
75 ohm
OFF ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp/H sync V sync
R
G
B
PORT 3
PORT 6
REMOTE
COMMUNICATION
PROJECTOR MODE POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operational
RED : stand-by
Connections
3-6 5975847 BARCOGRAPHICS 1208S 220197
PERIPHERAL EQUIPMENT
Connecting a RCVDS 05 switcher to the
BARCOGRAPHICS 1208s
- Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs
when 10 RCVDS switchers are linked via the expansion modules.
- Serial communication with the projector.
- Remote control buttons on the RCVDS to control the
BARCOGRAPHICS 1208s (source selection and analog settings)
- The selected source number will be displayed on a 2 digit display
and the selected input modules will be indicated with a LED on the
rear.
For more information about the use of tje RCVDS, consult the
Owner's Manual of the RCVDS.
Order number : RCVDS05 : R5975765
Connecting a VS05 switcher to the
BARCOGRAPHICS 1208s.
The VS05 can switch up to 5 Composite Video sources, 3 S-Video
Sources and 1 RGB analog or component Video source to the
BARCOGRAPHICS 1208s. In addition, an audio signal associated
with the source, can be switched to an audio amplifier.
Order number : R9827890.
For more information about the use of the VS05, consult the VS05
Owner's Manual, order number : R5975245.
Connecting an IR Remote Receiver to the
BARCOGRAPHICS 1208s
This infra-red receiver unit makes it possible to control the
BARCOGRAPHICS 1208s from another room. There is a communi-
cation line cable between the IR receiver and the projector or the
RCVDS 800. The infrared control information from the Remote
Control Unit is sent to the IR Remote Receiver. The IR Remote
Receiver 800 displays the selected source on a 7-segment display.
Order number : R9827515.
Controlling
4-1
5975847 BARCOGRAPHICS 1208s 220197
4
CONTROLLING
Caution : Do not display a stationary image with full brightness
and contrast for longer than 20 min., otherwise you risk damage
to the CRT's.
Battery installation in the RCU.
A new battery (not yet installed to save the battery life) is delivered inside the plastic bag with the power
cord. Before using the RCU, follow the battery installation procedure.
Remove the battery cover on the backside of the RCU by pushing the indicated handle a little to the
bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
Insert the new 9 V battery (type 6F22S or equivalent) in the lower compartment and connect the battery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.
fig.1
310a.DRW
fig.2
Battery
Contact
plate
Insert here,
behind the
plastic cover, the
'Insert card for
RCU'. You can
cut out the
correct insert
card on one of
the last pages of
this manual.
Controlling
4-2 5975847 BARCOGRAPHICS 1208s 220197
The BARCOGRAPHICS 1208s can be controlled with
a. the RCU
b. the hardwired RCU (cable not included)
c. the built-in RCU (local keypad)
The procedure and results of controlling the projector with either of
these RCU options is essentially the same.
How to use your RCU
a) Point the front of the RCU towards the reflective screen surface
b) Point the front of the RCU towards one of the IR sensors in the
projector.
When using the wireless remote control, make sure you are within the
effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
IR Receiver Locations on the Projector:
c) RCU used in a hardwired configuration.
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the rear panel of the
BARCOGRAPHICS 1208s labelled 'REMOTE'.
d) Built-in RCU (local keypad)
To gain access to the built-in RCU, see paragraph 'The local keypad'
Projector Address
a. hardware set up of the projector address.
Every projector requires an individual address between 0 and 255
which is set with hardware DIP switches inside the projector. To
change that address, contact a BARCO authorized technician.
b. How to control the projector.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now with :
- the RCU for addresses between 1 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : a projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself. Address "O"
is therefore a universal address.
c. Using your RCU.
Before using your RCU, it is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
Ceiling
Screen
IR sensor
RCU800
0
9
7
8
6
5
43
2
1
ENTER
0
9
7
8
6
5
43
2
1
ENTER
365
45°
45°
45°
45°
366
RS232 OUTRS232 IN
IR
REMOTE
Controlling
4-3
5975847 BARCOGRAPHICS 1208s 220197
Port No Projector input Press Digit
Button
1 Comp. Video 1
2 S-Video
1
/Comp. Video* 2
3 RGB
2
3
4/5 RGB
2
4 or 5
4/5 Component video
3
6
4/5 RGB with Tri level sync
4
7
4/5 Component video
with Tri-level sync
5
8
How to display a projector address?
Press the ADDRESS key (recessed key on the RCU) with a pencil.
The projector's address will be displayed in a 'Text box'. This text box
PROJECTOR
ADDRESS
001
disappears after a few seconds.
To continue using your RCU, it is necessary to enter the same
address with the digit buttons (address between 0 and 9). For
exemple, if the Adrress Key displays projector address 003, then
press the "3" digit button on the RCU to set the RCU's address to
match the projector's address.
How to program an address into the RCU?
Press the ADDRESS key (recessed key on the RCU) with a pencil
and enter the address with the digit buttons. That address can be any
digit between 0 and 9.
When programming '0', zero address, the RCU will control a projector
regardless of the projector's address. This feature allows multiple
projectors with different addresses to be controlled by a single RCU.
Input selection
With the digit buttons on the RCU, it is possible to select input
sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S.
When a valid and available source is selected, there will be informa-
tion displayed on the screen about that source (if "Text" is on). This
information includes :
-source number
- horizontal frequency
- vertical frequency
Source 2
Fh= 15.6 kHz
Fv= 50 Hz
When the entry is a non valid source
number, a warning appears on the screen : 'input not available'.
WARNING
input not
available
When a valid source number is selected, the projector will display this
source or it will wait on the selected source number until the source
WARNING
source not
available
becomes available. A message 'source not available' will be dis-
played for a short time.
Only available when the optional Tri-level sync module is
installed.
1
Input signal Y/C (luma/chroma)
2
Input signal : R, G and B with automatic sync detection between
seperate sync (separate composite sync or with separate Hor
and Vert. sync) or sync on green (composite sync).
3
Input signal : R-Y, Y and B-Y with separate composite sync or
with separate Hor and Vert.sync or with composite sync on Y.
4
Input signal : R, G and B with separate Tri level sync or with Tri-
level sync on green.
5
Input signal : R-Y, Y and B-Y with separate Tri level sync or with
composite Tri-level sync.
* Video or S-Video : switchable in the PictureTuning menu.
Controlling
4-4 5975847 BARCOGRAPHICS 1208s 220197
Analog Picture Controls
The analog picture controls can be adjusted with the RCU. The control keys are
located on the lower right side of the key panel of the RCU and indicated with the name
of the control and an icon.
When an analog picture control is pressed, a text box with bar scale and the function
name of the control, e.g. 'brightness...' appears on the screen (only if
'TEXT' is ON).
The length of the bar scale indicates the current memorized setting for this
source. The bar scale changes as the + or - buttons of the control are pressed.
Brightness Control
A correct 'brightness' setting is important for good image reproduction. Adjust the
brightness with the + button and - button (RCU) until the darkest parts of the picture
appear black.
A bar scale gives a visual indication on the screen of the current brightness setting
BRIGHTNESS
35
189
while pressing on the above indicated keys. If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated
keys.
The bar scale increases when pressing on the + button (higher brightness) and decreases when pressing on the - button (lower brightness).
Contrast Control
A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting conditions. If the Contrast Control is too low, the picture will be too dim.
If it is set too high, the picture may be too bright and not sharp.
A bar scale gives a visual indication on the screen of the current contrast setting while pressing the + or - buttons (RCU). If the bar scale is
not visible on the screen, press '
TEXT' key once and retry the above indicated keys.
The bar scale increases when pressing on the + button (higher contrast) and decreases when pressing on the - button (lower contrast).
Color Saturation Control
Color saturation is only active for Video and S-Video Inputs. This control adjusts the color intensity of the picture. Adjust the color saturation
using the + and - buttons (RCU). A bar scale gives a visual indication on the screen of the current color setting while pressing on the above
indicated keys. If the bar scale is not visible on the screen, press '
TEXT' key once and retry the above indicated keys. The bar scale increases
when pressing on the + button (richer colors) and decreases when pressing the - button (lighter colors).
Tint Control
Tint is only active for Video and S-Video Inputs. The Tint Control is effective only when using the NTSC 4.43 or NTSC 3.58 system. A bar
scale gives a visual indication on the screen of the current tint setting while pressing the + or - buttons (RCU). If the bar scale is not visible
on the screen, press the '
TEXT' key once and retry the above indicated keys buttons.
The bar scale increases when pressing on the + button (greener flesh tones) and decreases when pressing the - button (redder flesh tones).
Sharpness Control.
Sharpness control only active for Video and S-Video Inputs. A bar scale gives a visual indication on the screen of the current sharpness setting
while pressing the + or - buttons (RCU). If the bar scale is not visible on the screen, press '
TEXT' key once and retry the above indicated keys.
The bar scale increases when pressing on the + button (sharper picture) and decreases when pressing on the - button (softer picture).
Controlling chained projectors.
Projectors can be controlled individually as well as in a group.
For individual control see previous pages.
For group control of the projectors.
(input selection and analog picture control)
Program the 'zero address' into any RCU. Therefore, press on the address key and key in the address ("0") with the numeric keys on the
RCU itself.
Once address '0' is pressed, all projectors will be controlled together until a new address is entered on the RCU. It is possible to have a
common input selection and a common analog picture control.
Once a new address is entered, only the projector with that specific address will follow the new instructions.
Note : For group control, all projectors in a control group must be capable of receiving the IR signal from the controlling RCU at the same time.
Start Up of the Adjustment Mode
5-1
5975847 BARCOGRAPHICS 1208S 220197
5
START UP OF THE ADJUSTMENT MODE
Adjustment Mode
All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Press the ADJUST key to enter the 'adjustment
mode'.
You are now in the 'Adjustment mode'. The
Control stick is used to make menu selections and also vertical and horizontal adjustments. The
ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate the
adjustment mode while any path selection menu is displayed.
When an adjustment menu is displayed on the screen and no action is taken within the first 5 minutes, the projector will automatically reduce
the brightness and contrast to a level so that the stationary image cannot damage the tubes.
There are 5 possible paths to follow once in the Adjustment mode. They are :
INSTALLATION - Installation should be selected if the projector has been
relocated and/or a different screen size is desired.
When selecting 'Installation', the user or operator will be warned to call a qualified
technician to perform the installation procedure (see example of projected warning
on the next page)
GUIDED - Guided should be selected if the user intends to perform a complete
alignment of the projected image. All of the necessary geometry and convergence
adjustments are made in a predetermined sequence.
RANDOM ACCESS - Random Access should be selected if the user intends to
make only a few adjustments.
SERVICE - Service should be selected if the user intends to delete blocks, change
password , select service adjustments or get set-up information.
IRIS - This selection will only be available when the IRIS Auto-Convergence unit
is connected to the projector.
While in Guided or Random Access adjustment Modes, the user may use an
external source, an internally generated genlocked pattern or an internally gener-
ated multifrequency cross hatch pattern as a setup pattern.
Warning during the start up of the installation mode.
ADJUSTMENT MODE
Select a path from
below:
Select with or
then <ENTER>
<EXIT> to return
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
Barco GRAPHICS 1208s Manuale utente
- Categoria
- Proiettori di dati
- Tipo
- Manuale utente
in altre lingue
- English: Barco GRAPHICS 1208s User manual