Sony VPH-G70QM Operating Instructions Manual

Marca: Sony

Modello: VPH-G70QM

Categoria: Proiettori di dati

Tipo: Operating Instructions Manual

Questo manuale è adatto anche per

3-866-495-11 (1)

VPH-G70Q

VPH-G70QM

VPH-G70QMG

Operating Instructions

Multiscan Projector

• The PDF data of the Operating Instructions and Installation Manual for Dealers (French, German,

Spanish and Italian) are contained in the supplied CD-ROM. If you need a manual other than the

English one, please read the data of the CD-ROM or print them out with a printer.

• When you use the CD-ROM, please read its “ReadMe” section, which introduces how to use the

CD-ROM.

• Les données PDF du mode d’emploi et du manuel d’installation destiné aux revendeurs (français,

allemand, espagnol et italien) se trouvent sur le CD-ROM fourni. Si vous avez besoin d’une autre

version du manuel que la version anglaise, consultez les données sur le CD-ROM ou imprimez-

les au moyen d’une imprimante.

• Avant d’utiliser le CD-ROM, veuillez lire la section “LisezMoi” qui vous explique comment exploiter

le CD-ROM.

• El CD-ROM suministrado contiene los datos PDF de los manuales de instrucciones y de

instalación para proveedores (español, francés, alemán e italiano). Si necesita un manual que no

sea el inglés, lea los datos del CD-ROM o imprímalos con una impresora.

• Cuando utilice el CD-ROM, lea su sección “Léame”, en la que se describe cómo emplear dicho

CD-ROM.

• Die Bedienungsanleitung und das Installationshandbuch für Händler (Französisch, Deutsch,

Spanisch und Italienisch) befinden sich im PDF-Format auf der mitgelieferten CD-ROM. Wenn Sie

nicht mit dem englischen Handbuch arbeiten möchten, lesen Sie bitte das Handbuch in der

gewünschten Sprache auf der CD-ROM, oder drucken Sie es aus.

• Wie Sie die CD-ROM verwenden, ist unter “ReadMe” auf der CD-ROM beschrieben.

• Le istruzioni per l’uso e il manuale d’uso per i rivenditori in formato PDF in lingua francese,

tedesca, spagnola e italiana sono contenuti nel CD-ROM in dotazione. Se occorre una copia dei

manuali non in lingua inglese, è possibile visualizzare i manuali del CD-ROM a video oppure

stamparli.

• Se si utilizza il CD-ROM, leggere la sezione “Leggimi” che spiega come utilizzare il CD-ROM.

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

For the customers in the USA

Note

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

Warning

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

For the customers in Canada

This Class A digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

For the customers in the United Kingdom

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

This wires in this mains lead are coloured in accordance with

the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol Y or coloured green or

green-and-yellow.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red.

Voor de klanten in Nederland

• Dit apparaat bevat een Li-ion batterij voor memory back-

up.

• De batterij voor memory back-up van het geheugen is

bevestigd op IC308 van plaat YB.

• Raadpleeg uw leverancier over de verwijdering van de

batterij op het moment dat u het apparaat bij einde

levensduur afdankt.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet

weggooien maar inleveren als KCA.

The socket-outlet should be installed near the equipment

and be easily accessible.

La toma mural debe estar instalada cerca del equipo y

debe accederse a ésta con facilidad.

AVERTISSEMENT

ACHTUNG

Pour les utilisateurs au Canada

Cet appareil numérique de la classe A respecte toutes les

exigences du Réglement sur le matériel brouilleur du

Canada.

La prise doit être près de l’appareil et facile d’accès.

Für Kunden in Deutschland

Dieses Produkt kann im kommerziellen und in begrenztem

Maße auch im industriellen Bereich eingesetzt werden. Dies

ist eine Einrichtung, welche die Funk-Entstörung nach

Klasse B besitzt.

Die Steckdose muß nahe bei diesem Gerät angebracht

und leicht zugänglich sein.

Afin d’éviter tout risque d’incendie et d’électrocution, ne

pas exposer l’appareil à la pluie ou à l’humidité.

Pour éviter tout risque de décharge électrique, ne pas

ouvrir le boîtier. Confiez l’entretien uniquement à un

personnel qualifié.

Um Feuergefahr und die Gefahr eines eiektrischen

Schlages zu vermeiden, darf das Gerät weder Regen

noch Feuchtigkeit ausgesetzt werden.

Im Geräteinneren befinden sich Teile, die unter

gefährlich hoher Spannung stehen. Das Gehäuse darf

nicht geöffnet werden. Überlassen Sie die Wartung nur

geschultem Fachpersonal.

Para evitar riesgos de incendio o electrocución, no

exponga la unidad a la lluvia ni a la humedad.

Para evitar recibir descargas eléctricas, no abra el

aparato. Contrate exclusivamente los servicios de

personal cualificado.

Per evitare il pericolo di incendi o scosse elettriche, non

esporre l’apparecchio alla pioggia o all’umidità e non

aprirlo.

Per eventuali riparazioni, rivolgersi esclusivamente a

personale qualificato.

ADVERTENCIA

AVVERTENZA

La presa di corrente deve essere situata vicino

all’apparecchio e deve essere facilmente accessibile.

Die geforderte Stückprüfung hat ergeben, daß die gemessene Ortsdosis-Leistung unter dem

im Prüfungsschein Nr. 6.22-S 1227 der PTB genannten Wert von 0,2 µSv/h liegt.

The instructions in this manual are for models VPH-G70Q, VPH-G70QM and

VPH-G70QMG. Before you start reading, check your model number. The VPH-

G70Q/QM are the models used for illustration purposes. The S VIDEO IN/OUT

connectors and VIDEO IN/OUT connectors on the rear panel are not supplied

with the VPH-G70QMG. Any differences in operation are clearly indicated in the

text.

Table of Contents

Overview

Projecting

Precautions.........................................................................8

Features ............................................................................10

Location and Function of Controls ................................11

Projecting..........................................................................19

Adjusting the Picture .......................................................21

Adjusting the Size and Shift of the Picture....................22

Centering Adjustment......................................................24

Adjustments and settings

using the menu

Using the Menu ................................................................26

The INPUT SELECT Menu ...............................................27

The PIC CTRL (Picture Control) Menu ...........................28

The INPUT SETTING Menu ..............................................30

The SET SETTING Menu..................................................33

The INPUT INFO (Information) Menu..............................36

The OPTION Menu............................................................37

Installation/connection

examples

Installation Examples ......................................................38

Installation 1 Floor Installation Using Front Projection

Flat Screen.................................................................. 38

Installation 2 Ceiling Installation Using Front Projection

Flat Screen.................................................................. 39

Connection Examples......................................................40

Connecting Directly to the Projector............................... 40

Using the Signal Interface Switcher................................ 41

Other

Maintenance

Troubleshooting...............................................................42

Specifications...................................................................43

Index..................................................................................46

On safety

•Check that the operating voltage of your unit is identical with the voltage

of your local power supply. If voltage adaptation is required, consult with

qualified Sony personnel.

•Should any liquid or solid object fall into the cabinet, unplug the unit and

have it checked by qualified personnel before operating it further.

•Unplug the unit from the wall outlet or set the MAIN POWER switch to

OFF if it is not to be used for several days.

•To disconnect the cord, pull it out by the plug. Never pull the cord itself.

•The wall outlet should be near the unit and easily accessible.

•The unit is not disconnected from the AC power source (mains) as long

as it is connected to the wall outlet, even if the unit itself has been turned

off.

On installation

•When the projector is mounted on the ceiling, the Sony PSS-70 Projector

Suspension Support must be used for installation. Read the installation

manual of the PSS-70 carefully, since the ceiling should be reinforced for

safety.

•Allow adequate air circulation to prevent internal heat build-up. Do not

place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains,

draperies) that may block the ventilation holes. Leave space of more than

30 cm (12 inches) between the wall and the projector. Be aware that room

heat rises to the ceiling; check that the temperature near the installation

location is not excessive.

•Do not install the unit in a location near heat sources such as radiators or

air ducts, or in a place subject to direct sunlight, excessive dust or

humidity, mechanical vibration or shock.

•To avoid moisture condensation, do not install the unit in a location

where the temperature may rise rapidly.

•Fans are installed inside the projector to prevent internal heat build-up.

The fans produce a humming noise when the power is switched on, which

is normal. Should the noise sound abnormal, please consult qualified

Sony personnel.

On illumination

•To obtain the best picture, the front of the screen should not be exposed

to direct lighting or sunlight.

•Ceiling-mounted spot lighting is recommended. Use a cover over

fluorescent lamps to avoid lowering the contrast ratio.

•Cover any windows that face the screen with opaque draperies.

•It is desirable to install the projector in a room where floor and walls are

not of light-reflecting material. If the floor and walls are of reflecting

material, it is recommended that the carpet and wall paper be changed to

a dark color.

Precautions

On operation

To turn on the projector after the projector has been turned off due to a

brief loss of power, press the POWER ON key on the remote control, or

turn off the MAIN POWER switch so that the STANDBY indicator turns

off and then turn on the MAIN POWER switch.

On cleaning

•To keep the cabinet looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a

mild detergent solution. Never use strong solvents, such as thinner,

benzene, or abrasive cleansers, since these will damage the cabinet.

•Avoid touching the lens. To remove dust on the lens, use a soft dry cloth.

Do not use a damp cloth, detergent solution, or thinner.

CRT burns

When a static picture of a VCR or a computer is displayed for more than

about an hour, a CRT burn may result. This means that an after-image

impression of the static picture remains on the screen even after the picture

has changed. If it is necessary to display the same static picture for more

than an hour, we recommend that you set the CONTR (contrast) control to

the lowest setting.

Also, when a picture of different size is displayed beyond a certain length

of time, an after-image impression of the frame of the smaller picture may

be burnt on the screen (such as displaying a 16:9 wide size picture on a 4:3

screen). To avoid this, we recommend that you use the same picture size

when possible. However, if it is necessary to use a different picture size,

set the CONTR (contrast) control and the BRT (brightness) control of the

smaller picture to the lowest setting possible. This will minimize the risk

of creating an after-image impression.

If the CRT burns, it must be replaced. In this case, refer to the warranty

provided with this unit. Consult your Sony dealer or Qualified Service

Personnel.

On repacking

Save the original shipping carton and packing material; they will come in

handy if you ever have to ship your unit. For maximum protection, repack

your unit as it was originally packed at the factory.

Overview

Features

Multiscan projector

This projector accepts and automatically detects horizontal scanning

frequencies between 15 kHz and 110 kHz and vertical scanning

frequencies between 38 Hz and 150 Hz.

In addition to high-resolution pictures from computers, you can also

project pictures from teletext decoders, VCRs and video cameras.

High resolution and brightness

A newly developed 8-inch electromagnetic focus CRT, a hybrid Sony

HACC (High-resolution Aspherical and Color Corrected) lens and a wide-

range cathode/G1 dual-drive video output circuit are incorporated in the

projector to provide a sharp and bright high-quality picture with the high

resolution of 1700 × 1200 pixels and the high light output of 240 lumen.

High contrast

The adoption of the optical coupling technologies, double-focus lens

system and an anti-reflection coating gives a fine-detail and sharp picture

with improved contrast in corners and screen center.

Easy operation—remote control, on-screen display

Adjustments such as input selection, picture control and centering

adjustment can be remotely controlled from both the front and rear of the

projector with the supplied remote control. You can also use the control as

a wired remote control by connecting it to the projector with the supplied

remote control cable.

Compatible with various color systems

NTSC, PAL, SECAM, NTSC4.43

or PAL-M color system can be selected

automatically or manually.

Flexible setup

You can project a 60- to 300-inch picture (120-inch standard) with this

projector. The projector can be set up on the floor or ceiling, for front or

rear projection to suit the installation location, surrounding illumination,

usage, etc.

Illuminated control panel/remote control keys

The key names on the remote control and the control panel of the projector

can be illuminated for easy access in a dark place by pressing the LIGHT

button.

..........................................................................................................................................................................................................

1) NTSC4.43 is the color system used when playing back a video recorded on NTSC on a NTSC4.43 system VCR.

Location and Function of Controls

Front

How to open the control

panel cover

1 Blue lens

2 Green lens

3 Red lens

4 Control panel cover

The control keys are inside the cover.

The locations and functions of the control keys are the

same as those of the remote control.

For details, see “Remote Control/Control Panel” on page

15.

5 Handles

Used for carrying the projector. The handles are

located on the front, rear, left and right sides.

6 Front remote control detector

7 Adjusters

Used to keep the projector level if it is installed on an

uneven surface (equipped with four adjusters).

How to use the adjusters

While lifting the projector, turn the adjusters to adjust

the height so that the projector becomes level.

Note

Be careful not to let the projector down on your fingers.

To raise

the projector

To lower

the projector

23 4

56 7

Location and Function of Controls

Using the handles

Pull out the front and rear handles or the side handles.

Putting away the handles

Push the handle release lever under each handle. The

handle is automatically retracted.

POWER

STANDBY

AC IN

MAIN POWER

ONOFF

100~120V 15A 250V

200V~240V T6.3A 250V

R-Y

B-Y

SYNC

INPUT A

S VIDEO

OUT

C IN

Y IN

VIDEO

OUT

ABL LINK

OUT

TRIGGER

PLUG IN

POWER

OUT

REMOTE

INDEX

RS-422A

CONTROL S

IN OUT

MODE

REMOTE1

Rear

1 Signal interface board attachment part (INPUT

The IFB-40 Signal Interface Board is installed at the

factory. Other optional signal interface boards can be

attached to this section instead of the IFB-40.

Indicator (red): Lights up when the input of the IFB-

40 is selected.

REMOTE 1 IN connector (14-pin multi): When

connecting two projectors, connect to the REMOTE

1 OUT connector on the IFB-40 installed to another

projector.

REMOTE 1 OUT connector (14-pin multi): Connect

to the REMOTE 1 IN connector on the IFB-40.

MODE selector: Turn the control switch of the

MODE selector to the appropriate position according

to the length of the cable connected to the REMOTE

1 OUT connector.

Cable length

Type of cable

Position

2 INPUT A connectors (BNC type)

R/R-Y/P

R, G/Y, B/B-Y/PB, SYNC/HD, VD

connectors: Connect to the outputs of a computer or a

video camera. According to the connected

equipment, the RGB (R, G, B), component (R-Y, G,

B-Y) or HDTV (P

R, Y, PB) signal is selected.

3 S VIDEO IN/OUT connectors (VPH-G70Q/QM

only)

Y IN, C IN connectors (BNC type): Connects to the

Y and C video outputs of the video equipment.

S VIDEO IN/OUT connectors (4-pin, mini-DIN

type): Connects to the S video output or input of the

video equipment.

Note

The S VIDEO IN connector is disconnected when a cable is

connected to the Y/C IN connectors.

4 TRIGGER connector (minijack)

When the projector is turned on, 5 V is output and

when it is turned off, 0 V is output. However, the

connector is not used as the power source since the

power is not output.

up to 2 m

SIC-M-1

CCQ-2BRS

up to 25 m

SIC-M-15

CCQ-25BRS

SIC-M-25

up to 10 m

SIC-M-5

CCQ-5BRS

CCQ-10BRS

up to 50 m

SIC-M-50

CCQ-50BRS

!™

!£

!¢

!∞

67 8 9

!º

!¡

Location and Function of Controls

!¡ MAIN POWER switch

!™ Error code window

An error code lights up when an operational error

occurs.

!£ POWER indicator

Lights in green when the power is turned on.

!¢ STANDBY indicator

Lights in orange when the MAIN POWER switch is

turned on. Once in the standby mode, you can turn the

projector on and off with the remote control.

!∞ Rear remote control detector

5 RS-422A REMOTE connector (D-sub 9-pin)

Used to expand the system connections using the RS-

422A interface.

Before using the connector, loosen the two screws to

remove the cap.

6 VIDEO IN/OUT connectors (VPH-G70Q/QM

only)

VIDEO IN connector (BNC type): Connects to the

composite video output of the video equipment.

VIDEO OUT connector (BNC type): Connects to the

composite video input of a color monitor.

7 ABL (Automatic Brightness Limiter) LINK IN/

OUT jacks (minijack)

When connecting multiple projectors, connects the

ABL LINK OUT jack to the ABL LINK IN jack on

another projector. You can synchronize the brightness

limiting point among the projectors, allowing to make

the whole screen brightness uniform.

8 CONTROL S jacks

IN/PLUG IN POWER (5 V) jack (stereo minijack):

Connects to the CONTROL S OUT jack of other

Sony equipment. Also connects to the CONTROL S

OUT jack of the supplied remote control with the

supplied remote control cable (stereo cable) to be

used as a wired remote control. In this case, this jack

supplys 5 V to the remote control as power source.

OUT jack (stereo minijack): Connects to the

CONTROL S IN jack of other Sony equipment.

Note

When using this jack, the remote control detector on the

projector does not function.

9 INDEX NO. switches

When multiple projectors are connected, set the index

number of each projector.

To display the index number on the screen, press the

NORMAL key, and the ENTER key on the remote

control.

Note

If you set the index number to “00,” the projector does not

operate.

!º AC IN socket

Connect the supplied AC power cord.

Remote Control/Control Panel

Note

The VOLUME +/– !¢, INPUT SELECT, C and D !¶,

AUDIO MUTING @¡ and LCD LENS CONTROL @™ keys

do not function with this projector.

The locations and functions of the keys on the remote

control are the same as those on the control panel of

the projector. (Only the remote control is equipped

with the transmission indicator and the COMMAND

ON/OFF switch.)

The remote control may be used as a wired or wireless

remote control.

1 LIGHT button

Illuminates the key indicators.

The key indicators turn off if you press the LIGHT

button again.

If you do not press any key for more than 30 seconds,

the indicators also turn off automatically.

If the COMMAND 6 switch on the remote control is

set to OFF, only the COMMAND switch is

illuminated.

When the remote control is connected to the

CONTROL S IN/PLUG IN POWER jack of the

projector via the remote control cable, the power is

supplied to the remote control from the projector.

2 Transmission indicator (only for the remote

control)

Lights each time you press a key. If it does not light,

replace the batteries with new ones.

3 STATUS ON/OFF key

Press OFF to eliminate the on-screen display.

Press ON to restore the on-screen display.

Note

The menus and warning messages appear even if the OFF

key is pressed.

PIC

AUDIO OFF

PATTERN

FOCUS

ZOOM

SHIFT

NORMAL

MUTING

STATUS

LCD LENS CONTROL

COMMAND

OFF

SIZE

SHIFT

RGB

CENT

OFF

POWER

MEMORY

VIDEO SELECT

INPUT SELECT

A D

BLKG

RESET

423

INDEX

0(ALL)

SECOND

SWITCHER/INDEX

SWITCHER

ENTER

POSITION

BRIGHT

CONTR

PICTURE CONTROL

HUE COLOR

SHARP VOLUME

LIGHT

VIDEO/S VIDEO

!•

!ª

@º

@¡

@™

@£

!¶

!§

!£

!∞

!¢

!º

!¡

!™

4 RGB SHIFT key

Enters the shift adjustment mode for the input signal.

Next adjust the position of the picture using the four

arrow keys. The picture shifts in the direction of the

arrow on the pressed key.

Press the MEMORY key 8 to store the adjusted value

and display the adjusted picture.

5 RGB SIZE key

Enters the size adjustment mode for the input signal.

Next adjust the size of the picture using the four arrow

keys.

B : to reduce horizontal size

b : to expand horizontal size

V : to expand vertical size

v : to reduce vertical size

Press the MEMORY key 8 to store the adjusted value

and display the adjusted picture.

6 COMMAND ON/OFF switch

No key on the remote control except the LIGHT button

1 function when this switch is set to OFF. This saves

the battery power.

7 CENT R/B keys

Enter the centering adjustment mode of the red and

blue.

R: Press to enter the red centering adjustment mode.

B: Press to enter the blue centering adjustment mode.

Perform the centering adjustment using the four arrow

keys.

8 MEMORY key

Stores various adjusted data into memory.

9 POWER ON/OFF keys

Turn on and off the projector when the MAIN

POWER switch on the projector is set to ON.

0 Menu operation keys

Used for various adjustment functions and for menu

operations.

MENU: Displays the main menu. Press it again to

turn off the menu.

Arrow keys: Adjusts the value or selects the item in

the menu.

ENTER: Stores the settings in the menu.

!¡ RESET key

Resets the adjusted levels to the factory preset or

service adjusted levels.

!™ POSITION +/– keys

Select the position to be adjusted on the screen in

blanking adjustment mode.

Also, set V SHIFT to WIDE or NARROW in the RGB

input signal’s SHIFT adjustment mode.

!£ PICTURE CONTROL keys

Adjust the picture conditions: CONTR (contrast),

BRIGHT (brightness), COLOR, HUE and SHARP

(sharpness).

!¢ VOLUME +/– keys

These keys do not function with this projector.

!∞ SWITCHER/INDEX select switch

Selects the function of the SWITCHER/INDEX keys.

Set to SWITCHER to select the input from the PC-

1271/1271M Signal Interface Switcher.

Set to INDEX to assign the index number of each

projector when multiple projectors are used.

!§ SWITCHER/INDEX keys

When the SWITCHER/INDEX select switch is set

to SWITCHER

When the PC-1271/1271M switcher (not supplied) is

connected to the projector, press a number key (1 – 8)

to select the input from the switcher. The number key

9 does not function.

To select the input from the second switcher (when the

SINGLE/SECOND/OTHER switch on the switcher is

set to SECOND), press a number key between 1 and 8

within two seconds after pressing the SECOND key.

When the SWITCHER/INDEX select switch is set

to INDEX

When multiple projectors are connected, select the

index number, which is set with the INDEX NO.

switch on the rear panel, of the projector to be

adjusted. Press a number key (1 – 9) to designate the

index number, then press the ENTER key. When

adjusting all the projectors simultaneously, press the 0

(ALL) key, then the ENTER key.

Location and Function of Controls

!¶ INPUT SELECT keys

Select the input signal.

VIDEO: VPH-G70Q/QM The video or S video

signal input from the VIDEO IN or S VIDEO IN (or

Y/C IN) connectors

VPH-G70QMG Video or S video signal input from

the optional IFB-G70QMG Video Interface Board

(when installing the IFB-G70QMG to the projector)

SELECT VIDEO/S VIDEO: VPH-G70Q/QM

Selects the signal input from the VIDEO IN or S

VIDEO IN (or Y/C IN) connectors by pressing this

key after pressing the VIDEO key.

VPH-G70QMG Selects video or S video signal

input from the optional IFB-G70QMG (when

installing the IFB-G70QMG to the projector) after

pressing the VIDEO key.

A: The RGB, component or HDTV signal input from

the INPUT A connectors of the projector

B: The signal input from the INPUT B section when

the optional interface board other than the IFB-40 is

installed

C, D: These keys do not function with this projector.

Note

To switch the input signal from the INPUT A or INPUT B

to the S VIDEO IN (or Y/C IN) connectors, first press the

VIDEO key, then press the SELECT VIDEO/S VIDEO key.

!• BLKG (blanking) key

Enters the blanking adjustment mode.

You can adjust the blanking with the four arrow keys.

!ª PATTERN key

Displays the internal test patterns of the projector.

Each press of the key displays CROSS HAIR,

HATCH (9 × 9), ME and COLOR BAR patterns,

sequentially.

@º NORMAL key

Erases the test pattern or cancels the various

adjustment modes.

@¡ MUTING keys

PIC (picture): Cuts off the picture. To restore the

picture, press the key again.

AUDIO: This key does not funcion with this

projector.

@™ LCD LENS CONTROL keys

These keys do not function with this projector.

@£ CONTROL S OUT jack (only for the remote

control)

Connects to the CONTROL S IN/PLUG IN POWER

jack on the projector for wired remote control

application.

PLUG IN

POWER

OUT

CONTROL S

Notes on wireless remote control operation

•Be sure that there is nothing to obstruct the infrared

beam between the remote control and the projector.

•The operation range is limited. The shorter the

distance between the remote control and the

projector, the wider the angle within which the

remote control can control the projector.

•The remote control detectors on the projector do not

operate when the remote control is being used as a

wired remote control. If you wish to use the remote

control as a wireless remote control, be sure to

remove the connecting cable from both the remote

control and the projector.

Connecting the remote control to the

projector

Location and Function of Controls

Battery installation

1 Push to open the lid.

2 Install the three R6 (size AA) batteries (supplied)

with the correct polarity.

3 Replace the lid.

Notes on batteries

•Be careful that the battery orientation is correct when

inserting batteries.

•Do not mix old battery with new one, or different

types of batteries.

•If you do not intend to use the remote control for a

long time, remove the batteries to avoid damage from

battery leakage. If a battery has leaked, remove the

batteries, wipe the battery compartment dry and

replace the batteries with new ones.

Rear of the projector

CONTROL

S OUT

Be sure to install

the battery from

the ’ side.

CONTROL S IN

Remote control cable

(supplied)

Projecting

ONOFF

MAIN POWER

SELECT

SWITCHER

INDEX

PIC ONAUDIO OFF

PATTERN

FOCUS

ZOOM

SHIFT

NORMAL

MUTING

STATUS

LCD LENS CONTROL

COMMAND

OFF

RGB

SHIFT

CENT

ONOFF

MEMORY

VIDEO

INPUT SELECT

ADBC

BLKG

RESET

1423

5867

0(ALL)

SECOND

SWITCHER/INDEX

ENTER

POSITION

BRIGHT

CONTR

PICTURE CONTROL

HUE

COLOR

SHARP

VOL

VIDEO/S VIDEO

LIGHT

POWER

SHIFT

1, 6

Front remote control detector

MENU key

SWITCHER/INDEX select switch

and number keys

1 Press the MAIN POWER switch on the rear of the projector.

The u STANDBY indicator lights in orange and the projector goes

into the standby mode.

2 Press the POWER ON key on the remote control or the control panel.

The POWER indicator lights in green.

A white screen with the message shown below (warming up screen)

appears on the screen. Make sure to allow the projector to warm up for

20 minutes after turning it on.

The message disappears temporarily in about 35 seconds, and will

appear subsequently for 5 seconds every 30 seconds.

Press the MENU key to cancel the warming up screen and see the

picture immediately after the projector is turned on if, for example, the

adjustment has been finished and warming up is not needed.

(continued)

INPUT-A



For optimum

performance

white screen will

remain for 20min.

For immediate use,

push [MENU] key.

u STANDBY indicator/

POWER indicator/

Rear remote control detector

Control panel (inside the cover)

Remote control

Point it toward the front

remote control detector.

3 Turn on the power of the connected equipment.

4 Select the input signal to be projected by pressing the INPUT SELECT

key.

VIDEO and SELECT keys: To project the signal input from the

equipment connected to the VIDEO IN or S VIDEO IN (or Y/C IN)

connectors. Select VIDEO or S VIDEO by pressing the VIDEO key,

then the SELECT key.

A: To project the RGB, component or the HDTV signal input from the

equipment connected to the INPUT A connectors.

B: To project the signal input from the equipment connected to the

optional interface board other than the IFB-40 installed to the

INPUT B section.

When the PC-1271/1271M Signal Interface Switcher is connected:

Set the SWITCHER/INDEX select switch to SWITCHER and then

select the input with the number keys 1 to 8. If two switchers are

connected, press the SECOND key and then the number key to

select the input from the second switcher.

Note

When you select the input signal connected to the INPUT A or INPUT B section,

be sure to select the correct signal in the SET SETTING menu. If an incorrect

signal is selected, picture may be distorted.

For details, see “The SET SETTING Menu” on page 33.

5 Adjust the picture.

For details, see “Adjusting the picture” on page 21.

6 To turn the power off, press the POWER OFF key on the remote

control or on the control panel of the projector, then set the MAIN

POWER switch on the projector to OFF.

Note

To turn on the projector after the projector has been turned off due to a brief loss

of power, press the ON key on the remote commander, or turn off the MAIN

POWER switch so that the STANDBY indicator turns off and then turn on the

MAIN POWER switch.

Projecting

To Press

Turn off the on-screen the STATUS OFF key.

display The menus and warning messages

appear even if the OFF key is pressed.

To restore the on-screen display, press

the STATUS ON key.

Cut off the picture the MUTING PIC key.

To restore the picture, press the

MUTING PIC key.

La pagina sta caricando ...

Sony VPH-G70QM Operating Instructions Manual

Marca: Sony

Modello: VPH-G70QM

Categoria: Proiettori di dati

Tipo: Operating Instructions Manual

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Sony VPH-G70QM

Sony VPH-G70QM Operating Instructions Manual

Questo manuale è adatto anche per

Sony VPH-G70QM Operating Instructions Manual

in altre lingue

Documenti correlati

Altri documenti