Denon Stereo Receiver AVR-1707 Manuale utente

Marca: Denon

Modello: Stereo Receiver AVR-1707

Tipo: Manuale utente

Questo manuale è adatto anche per

AVR-1707

AV SURROUND RECEIVER

AVR-1707

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

ISTRUZIONI PER L’USO

INSTRUCCIONES DE FUNCIONAMIENTO

GEBRUIKSAANWIJZING

BRUKSANVISNING

¢SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

To completely disconnect this product from the mains, disconnect the plug

from the wall socket outlet.

The mains plug is used to completely interrupt the power supply to the unit

and must be within easy access by the user.

VORSICHT:

Um dieses Gerät vollständig von der Stromversorgung abzutrennen, trennen

Sie bitte den Netzstecker von der Wandsteckdose ab.

Die Hauptstecker werden verwendet, um die Stromversorgung zum Gerät

völlig zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen

sein.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur, débranchez

la prise de la prise murale.

La prise secteur est utilisée pour couper complètement l’alimentation de

l’appareil et l’utilisateur doit pouvoir y accéder facilement.

ATTENZIONE:

Per scollegare definitivamente questo prodotto dalla rete di alimentazione

elettrica, togliere la spina dalla relativa presa.

La spina di rete viene utilizzata per interrompere completamente l’alimentazione

all’unità e deve essere facilmente accessibile all’utente.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación

eléctrica, desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación se utiliza para interrumpir por completo el

suministro de alimentación a la unidad y debe de encontrarse en un lugar al

que el usuario tenga fácil acceso.

VOORZICHTIGHEID:

Om de voeding van dit product volledig te onderbreken moet de stekker uit

het stopcontact worden getrokken.

De netstekker wordt gebruikt om de stroomtoevoer naar het toestel volledig

te onderbreken en moet voor de gebruiker gemakkelijk bereikbaar zijn.

FÖRSIKTIHETSMÅTT:

Koppla loss stickproppen från eluttaget för att helt skilja produkten från nätet.

Stickproppen används för att helt bryta strömförsörjningen till apparaten,

och den måste vara lättillgänglig för användaren.

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which this

declaration relates, is in conformity with the following standards:

EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.

Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive.

ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich

diese Erklärung bezieht, den folgenden Standards entspricht:

EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.

Entspricht den Verordnungen der Direktive 73/23/EEC, 89/336/EEC und

93/68/EEC.

DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel se

réfère cette déclaration, est conforme aux standards suivants:

EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.

D’après les dispositions de la Directive 73/23/EEC, 89/336/EEC et 93/68/EEC.

DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra

dichiarazione si riferisce, è conforme alle seguenti normative:

EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.

In conformità con le condizioni delle direttive 73/23/EEC, 89/336/EEC e

93/68/EEC.

QUESTO PRODOTTO E’ CONFORME

AL D.M. 28/08/95 N. 548

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto al que

hace referencia esta declaración, está conforme con los siguientes estándares:

EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.

Siguiendo las provisiones de las Directivas 73/23/EEC, 89/336/EEC y 93/68/EEC.

EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt, waarop

deze verklaring betrekking heeft, in overeenstemming is met de volgende

normen:

EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.

Volgens de bepalingen van de Richtlijnen 73/23/EEC, 89/336/EEC en 93/68/EEC.

ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg

avser, uppfyller följande standarder:

EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.

Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC och 93/68/EEC.

DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKAENGLISH

¢NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO / NOTAS SOBRE EL USO /

ALVORENS TE GEBRUIKEN / OBSERVERA

•Avoid high temperatures.

Allow for sufficient heat dispersion when installed in a

rack.

•Vermeiden Sie hohe Temperaturen.

Beachten Sie, daß eine ausreichend Luftzirkulation

gewährleistet wird, wenn das Gerät auf ein Regal gestellt

wird.

•Eviter des températures élevées

Tenir compte d’une dispersion de chaleur suffisante lors de

l’installation sur une étagère.

• Evitate di esporre l’unità a temperature alte.

Assicuratevi che ci sia un’adeguata dispersione del calore

quando installate l’unità in un mobile per componenti

audio.

• Evite altas temperaturas.

Permite la suficiente dispersión del calor cuando está

instalado en la consola.

•Vermijd hoge temperaturen.

Zorg voor een degelijk hitteafvoer indien het apparaat op

een rek wordt geplaatst.

• Undvik höga temperaturer.

Se till att det finns möjlighet till god värmeavledning vid

montering i ett rack.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Gehen Sie vorsichtig mit dem Netzkabel um.

Halten Sie das Kabel am Stecker, wenn Sie den Stecker

herausziehen.

• Manipuler le cordon d’alimentation avec précaution.

Tenir la prise lors du débranchement du cordon.

• Manneggiate il filo di alimentazione con cura.

Agite per la spina quando scollegate il cavo dalla presa.

•Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el cordón de

energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast wanneer deze moet

worden aan- of losgekoppeld.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-uttaget.

• Keep the apparatus free from moisture, water, and dust.

• Halten Sie das Gerät von Feuchtigkeit, Wasser und Staub

fern.

•Protéger l’appareil contre l’humidité, l’eau et lapoussière.

•Tenete l’unità lontana dall’umidità, dall’acqua e dalla

polvere.

• Mantenga el equipo libre de humedad, agua y polvo.

• Laat geen vochtigheid, water of stof in het apparaat

binnendringen.

• Utsätt inte apparaten för fukt, vatten och damm.

• Unplug the power cord when not using the apparatus for

long periods of time.

•Wenn das Gerät eine längere Zeit nicht verwendet werden

soll, trennen Sie das Netzkabel vom Netzstecker.

•Débrancher le cordon d’alimentation lorsque l’appareil n’est

pas utilisé pendant de longues périodes.

• Disinnestate il filo di alimentazione quando avete

l’intenzione di non usare il filo di alimentazione per un lungo

periodo di tempo.

• Desconecte el cordón de energía cuando no utilice el

equipo por mucho tiempo.

• Neem altijd het netsnoer uit het stopkontakt wanneer het

apparaat gedurende een lange periode niet wordt gebruikt.

• Koppla ur nätkabeln om apparaten inte kommer att

användas i lång tid.

* (For apparatuses with ventilation holes)

• Do not obstruct the ventilation holes.

• Die Belüftungsöffnungen dürfen nicht verdeckt werden.

• Ne pas obstruer les trous d’aération.

• Non coprite i fori di ventilazione.

• No obstruya los orificios de ventilación.

• De ventilatieopeningen mogen niet worden beblokkeerd.

• Täpp inte till ventilationsöppningarna.

• Do not let foreign objects into the apparatus.

• Keine fremden Gegenstände in das Gerät kommen lassen.

• Ne pas laisser des objets étrangers dans l’appareil.

• E’ importante che nessun oggetto è inserito all’interno

dell’unità.

• No deje objetos extraños dentro del equipo.

• Laat geen vreemde voorwerpen in dit apparaat vallen.

• Se till att främmande föremål inte tränger in i apparaten.

• Do not let insecticides, benzene, and thinner come in

contact with the apparatus.

• Lassen Sie das Gerät nicht mit Insektiziden, Benzin oder

Verdünnungsmitteln in Berührung kommen.

•Ne pas mettre en contact des insecticides, du benzène et

un diluant avec l’appareil.

• Assicuratevvi che l’unità non venga in contatto con

insetticidi, benzolo o solventi.

• No permita el contacto de insecticidas, gasolina y

diluyentes con el equipo.

• Laat geen insektenverdelgende middelen, benzine of

verfverdunner met dit apparaat in kontakt komen.

• Se till att inte insektsmedel på spraybruk, bensen och

thinner kommer i kontakt med apparatens hölje.

• Never disassemble or modify the apparatus in any way.

•Versuchen Sie niemals das Gerät auseinander zu nehmen

oder auf jegliche Art zu verändern.

• Ne jamais démonter ou modifier l’appareil d’une manière

ou d’une autre.

• Non smontate mai, nè modificate l’unità in nessun modo.

• Nunca desarme o modifique el equipo de ninguna manera.

• Nooit dit apparaat demonteren of op andere wijze

modifiëren.

•Ta inte isär apparaten och försök inte bygga om den.

CAUTION:

• The ventilation should not be impeded by covering the ventilation openings with items,

such as newspapers, tablecloths, curtains, etc.

• No naked flame sources, such as lighted candles, should be placed on the apparatus.

•Attention should be drawn to the environmental aspects of battery disposal.

• Do not expose the set to dripping or splashing fluids.

• No objects filled with liquids, such as vases, shall be placed on the apparatus.

ACHTUNG:

• Die Belüftung sollte auf keinen Fall durch das Abdecken der Belüftungsöffnungen durch

Gegenstände wie beispielsweise Zeitungen, Tischtücher, Vorhänge o. Ä. behindert werden.

• Auf dem Gerät sollten keinerlei direkten Feuerquellen wie beispielsweise angezündete

Kerzen aufgestellt werden.

• Bitte beachten Sie bei der Entsorgung der Batterien die geltenden Umweltbestimmungen.

• Das Gerät sollte keinerlei Flüssigkeit, also keinem Tropfen oder Spritzen ausgesetzt

werden.

• Auf dem Gerät sollten keinerlei mit Flüssigkeit gefüllten Behälter wie beispielsweise Vasen

aufgestellt werden.

ATTENTION:

• La ventilation ne doit pas être gênée en recouvrant les ouvertures de la ventilation avec des

objets tels que journaux, rideaux, tissus, etc.

• Aucune flamme nue, par exemple une bougie, ne doit être placée sur l’appareil.

•Veillez à respecter l’environnement lorsque vous jetez les piles usagées.

•L’appareil ne doit pas être exposé à l’eau ou à l’humidité.

• Aucun objet contenant du liquide, par exemple un vase, ne doit être placé sur l’appareil.

PRECAUZIONI:

• Le aperture di ventilazione non devono essere ostruite coprendole con oggetti, quali

giornali, tovaglie, tende e così via.

•Non posizionare sull'apparecchiatura fiamme libere, come ad esempio le candele accese.

•Prestare attenzione agli aspetti legati alla tutela dell'ambiente quando si smaltisce la

batteria.

•L’apparecchiatura non deve essere esposta a gocciolii o spruzzi.

•Non posizionare sull'apparecchiatura nessun oggetto contenete liquidi, come ad esempio i

vasi.

PRECAUCIÓN:

• La ventilación no debe quedar obstruida por hacerse cubierto las aperturas con objetos

como periódicos, manteles, cortinas, etc.

• No debe colocarse sobre el aparato ninguna fuente inflamable sin protección, como velas

encendidas.

•A la hora de deshacerse de las pilas, respete la normativa para el cuidado del medio

ambiente.

• No se expondrá el aparato al goteo o salpicaduras cuando se utilice.

• No se colocarán sobre el aparato objetos llenos de líquido, como jarros.

WAARSCHUWING:

• De ventilatie mag niet worden belemmerd door de ventilatieopeningen af te dekken met

bijvoorbeeld kranten, een tafelkleed, gordijnen, enz.

• Plaats geen open vlammen, bijvoorbeeld een brandende kaars, op het apparaat.

• Houd u steeds aan de milieuvoorschriften wanneer u gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan druppels of spatten.

• Plaats geen voorwerpen gevuld met water, bijvoorbeeld een vaas, op het apparaat.

OBSERVERA:

•Ventilationen bör inte förhindras genom att täcka för ventilationsöppningarna med föremål

såsom tidningar, bordsdukar, gardiner osv.

• Inga blottade brandkällor, såsom tända ljus, bör placeras på apparaten.

• Tänk på miljöaspekterna när du bortskaffar batteri.

• Apparaten får inte utsättas för vätska.

• Inga objekt med vätskor, såsom vaser, får placeras på apparaten.

ENGLISHDEUTSCHFRANCAISITALIANOESPAÑOLNEDERLANDSSVENSKA

III

A NOTE ABOUT RECYCLING:

This product’s packaging materials are recyclable and can be reused. Please dispose of any

materials in accordance with the local recycling regulations.

When discarding the unit, comply with local rules or regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with the local

regulations concerning chemical waste.

This product and the accessories packed together constitute the applicable product according to the

WEEE directive except batteries.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist für zum Recyceln geeignet und kann wieder verwendet werden. Bitte

entsorgen Sie alle Materialien entsprechend der örtlichen Recycling-Vorschriften.

Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und Bestimmungen.

Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden; bitte geben Sie die Batterien gemäß

örtlichen Bestimmungen an den Sammelstellen oder Sondermüllplätzen ab.

Dieses Produkt zusammen mit den Zubehörteilen ist das geltende Produkt der WEEE-Direktive, davon

ausgenommen sind die Batterien.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être réutilisés. Veuillez disposer de tout

matériau conformément aux réglements de recylage locaux.

Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations locales.

Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux réglements locaux

concernant les déchets chimiques.

Ce produit et les accessoires emballés ensemble sont des produits conformes à la directive DEEE sauf pour les piles.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali conformemente alle

normative locali sul riciclaggio.

Per smaltire l’unità, osservare la normativa in vigore nel luogo di utilizzo.

Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui rifiuti chimici.

Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad eccezione delle batterie.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar. Disponga de estos

materiales siguiendo los reglamentos de reciclaje de su localidad.

Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.

Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos de su localidad

relacionados con los desperdicios químicos.

Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva RAEE excepto pilas.

EEN AANTEKENING WAT BETREFT HET RECYCLEREN:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt verzocht om zich van

elk afvalmateriaal te ontdoen volgens de plaatselijke voorschriften.

Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed op.

Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke voorschriften

betreffende chemisch afval worden verwijderd.

Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor afgedankte elektrische en

elektronische apparaten (WEEE) van toepassing.

EN KOMMENTAR OM ÅTERVINNING:

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala återvinningsbestämmelser.

När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.

Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser för kemiskt avfall.

Denna apparat och de tillbehör som levereras med den är de som uppfyller gällande WEEE-direktiv, med undantag

av batterierna.

DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKAENGLISH

ENGLISH

Contents

Thank you for choosing the DENON AVR-1707 AV Surround Receiver. This remarkable component has been engineered to provide superb surround sound listening with home theater sources such as DVD, as well

as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding.

Accessories······················································································2

Before using ····················································································2

Cautions on installation·································································3

About the remote control unit······················································3

Inserting the batteries····································································3

Operating range of the remote control unit································3

Part names and functions

Front panel ·····················································································4

Display····························································································4

Rear panel ······················································································5

Remote control unit ···································································5, 6

Easy to setup flow··········································································7

Speaker layout [Basic layout]························································7

Speaker connections ······································································8

Connecting a DVD player and monitor ········································9

Auto Setup

q Connecting a microphone ·······················································10

w Before performing the Auto Setup procedure ························10

e Switching the front speaker ····················································10

r Starting Auto Setup·································································11

Error messages ············································································12

Cable indications ··········································································13

The video conversion function····················································13

Connecting a TV/DBS tuner ························································14

Connecting a video camera or video game ··································14

Connecting the external inputs (EXT. IN) terminals ·················14

Connecting a CD player ·······························································15

Connecting a tape deck, CD recorder or MD recorder··············15

Connecting a VCR·········································································15

Connecting the antenna terminals ·············································16

Connecting the iPod

··································································17

Connecting the power supply cord ············································17

Playing the input source ······························································18

Turning the sound off temporarily (MUTING)·······························19

Listening over headphones··························································19

Switching the front speakers ······················································19

Checking the currently playing program source, etc. ··················19

Switching the brightness of the display·······································19

Using the surround modes

Types of surround modes and their features·························19, 20

Selecting the play mode (DIRECT/STEREO)································20

Selecting the Dolby Digital and DTS Surround mode

(only with digital input) ·································································21

Selecting the Dolby Pro Logic IIx (Pro Logic II) mode·················22

Selecting the DTS NEO:6 mode ··················································23

Surround modes and parameters········································24 ~ 26

Basic Operation

Getting Started

Easy Setup Procedure

Connecting Other Sources

Using the DENON original surround modes

Types of surround modes and their features·······························27

Selecting the DSP surround simulation ·······································28

Setting the tone control ·······························································29

Adjusting the speaker volume ·····················································29

Listening to the radio

Auto preset memory····································································29

Auto tuning···················································································30

Manual tuning ··············································································30

Preset memory ············································································30

Recalling preset stations······························································30

RDS (Radio Data System) ····························································31

RDS search ··················································································31

PTY search ···················································································31

TP search ·····················································································32

RT (Radio Text) ·············································································32

Night mode ···················································································33

User mode function

Storing the settings in the memory ·············································33

Calling the settings out ································································33

Combining the currently playing sound

with the desired image (VIDEO SELECT function)····················33

Personal memory plus function ··················································33

Playing the iPod

·········································································33

Listening to music in the Browse mode······································34

Viewing still pictures and videos (only for iPods

equipped with the slideshow / video function)····························35

Disconnecting the iPod ································································35

Recording the program source

(recording the source currently being monitored)····················35

About the memory functions ······················································35

Initialization of the microprocessor············································35

Advanced Operation

ENGLISH

Speaker Setup

Setting the Speaker Configuration·········································43, 44

Setting the Subwoofer Mode Setup············································44

Setting the Distance ······························································44, 45

Setting the Crossover Frequency ················································45

Setting the Test Tone ···································································45

Troubleshooting············································································

Additional Information···························································

51, 52

Specifications················································································

List of preset codes ············································End of this manual

Operating DENON audio components ·······································46

Setting the preset memory function··········································46

Operating a component stored in the preset memory····47 ~ 49

Setting the punch through function···········································50

Advanced Setup – Part 2

Operating the remote control unit

Accessories

Check that the following parts are attached in addition to the main

unit:

q Operating instructions ..............................................................1

w Service station list ....................................................................1

e Remote control unit (RC-1049).................................................1

r R6P/AA batteries ......................................................................2

t AM loop antenna ......................................................................1

y FM indoor antenna ...................................................................1

u Setup microphone (DM-S205) (Approx. 6 m)...........................1

Getting Started

Before using

Pay attention to the following before using this unit:

• Moving the unit.

To prevent short-circuits or damaged wires in the connection cables,

always unplug the power supply cord and disconnect the connection

cables between all other audio components when moving the unit.

• Cautions on using mobile phones.

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

•Before turning the power operation button on.

Check once again that all connections are correct and that there are

not problems with the connection cables. Always set the power

operation button to the standby position before connecting and

disconnecting connection cables.

• Store these instructions in a safe place.

After reading, store this instructions along with the warranty card in

a safe place.

• Whenever the power operation button is in the STANDBY state,

the unit is still connected to AC line voltage.

Please be sure to turn off the power operation button or unplug

the cord when you leave home for, say, a vacation.

• Note that the illustrations in these instructions may differ from

the actual unit for explanation purposes.

System setup items and default values·······························36, 37

Navigating through the System Setup items ···························38

About the front display································································38

Input Setup

Setting the Digital In Assignment ················································39

Setting the iPod Assignment ······················································39

Setting the Component In Assignment ·······································39

Setting the Video Convert····························································40

Setting the Audio Delay ·······························································40

Setting the EXT. IN Subwoofer Level ·········································40

Setting the Auto Preset Memory·················································41

Option Setup

Setting the Power Amplifier Assignment ····································41

Setting the Volume Control··························································42

Setting the 2ch Direct/Stereo Custom·········································42

Setting the Auto Surround Mode·················································43

Advanced Setup – Part 1

Getting Started Getting Started

ENGLISH

About the remote control unit

In addition to controlling the AVR-1707, the attached remote control

unit (RC-1049) can also be used to control the following products:

q DENON component products

w Component products other than DENON:

• Set using the preset memory function ( page 46).

Cautions on installation

Wall

Note

Note:

For heat dispersal, do not install this unit in a confined space

such as a bookcase or similar enclosure.

Inserting the batteries

q Remove the remote control

unit’s rear cover.

w Set two R6P/AA batteries in

the battery compartment in

the indicated direction.

e Put the rear cover back on.

Notes on batteries:

• Replace the batteries with new ones if the set does not operate

even when the remote control unit is operated nearby the unit.

(The attached batteries are only for verifying operation.)

• When inserting the batteries, be sure to do so in the proper

direction, following the “<” and “>” marks in the battery

compartment.

•To prevent damage or leakage of battery fluid:

• Do not use a new battery together with an old one.

•Do not use two different types of batteries.

•Do not short-circuit, disassemble, heat or dispose of batteries

in flames.

• Remove the batteries from the remote control unit when you do

not plan to use it for an extended period of time.

• If the battery fluid should leak, carefully wipe the fluid off the

inside of the battery compartment and insert new batteries.

• Remove the batteries from the remote if it will not be in use for

long periods.

Operating range of the remote control unit

30°

Approx. 7 m

• Point the remote control unit at the remote sensor when operating

it.

• The remote control unit can be used from a distance of approximately

7 meters, at a horizontal angle of up to 30° with respect to the

sensor.

NOTE:

• It may be difficult to operate the remote control unit if the remote

sensor is exposed to direct sunlight or strong artificial light.

Getting Started Getting Started

ENGLISH

Display

Signal channel indicator

Lights when the preset channel is displayed at

Information display

Input signal indicators

Master volume indicator

This displays the volume level.

The Setup item number is displayed in System

Setup.

STEREO indicator

This lights when an FM stereo broadcast has

been received.

AUTO indicator

This lights when the broadcast station is

selected in the AUTO tuning mode.

TUNED indicator

This lights when an FM/AM broadcast has been

received.

RDS indicator

This lights when an RDS broadcast has been

received.

Part names and functions

Front panel

For details on the functions of these parts, refer to the pages given in parentheses ( ).

Power operation button

(ON/STANDBY)··········································(10)

Power indicator ·········································(10)

Power switch ·······································(10, 35)

Headphones jack (PHONES)·····················(19)

ANALOG button ········································(18)

SPEAKER buttons································(10, 35)

SURROUND BACK button ························(21)

SHIFT button··············································(30)

USER MODE buttons ································(33)

PRESET buttons···································(29, 30)

V. AUX INPUT terminals

Remove the cap covering the terminals when

you want to use them.

SETUP MIC jack ·········································(10)

SYSTEM SETUP button ····························(38)

SURR. MODE/SURR. PARA button··········(18)

SELECT/ENTER knob ··························(20, 28)

#0 @8 @6@9

@3@5 @2 !9 !7@1

!8@4

r y i o !1 !4!2 !5 !6

u !0

rtiyu

Cursor buttons (

) ·······························(21)

MASTER VOLUME control knob··············(18)

TUNING buttons (•, ª) ·····························(30)

RT button····················································(32)

PTY button ·················································(31)

RDS button·················································(31)

SURROUND BACK indicator·····················(21)

Display

INPUT mode indicators·····························(18)

SIGNAL indicators ·····································(21)

BAND button··············································(30)

@7 EXT. IN button············································(18)

Remote control sensor································(3)

INPUT MODE button·································(18)

INPUT SELECTOR knob ····························(18)

• The SELECT/ENTER knob on the main unit operates in

the same way as the CURSOR

and

buttons on

the remote control unit.

• The control functions in the same way as the

CURSOR

button when turned counterclockwise,

as the CURSOR

button when turned clockwise.

• The control functions in the same way as the

ENTER button when pressed the knob.

Getting Started Getting Started

ENGLISH

Remote control unit

Remote control signal

transmitter························(3)

Power buttons··········(10, 47)

Master volume control

buttons····························(18)

CH SELECT/ENTER

button··················(21, 29, 47)

NIGHT/AUDIO

button························(33, 47)

MUTING button··············(19)

STATUS/RETURN

button························(19, 47)

Tuner system/System

buttons ···················(30 ~ 32)

Rear panel

PRE OUT terminal········································(8)

EXT. IN terminals·······································(14)

DIGITAL terminals

(Optical/Coaxial) ·······································(9, 15)

AUDIO OUT terminals···························(9, 15)

Speaker terminals ·································(8, 41)

Power supply cord·····································(17)

AC outlet ····················································(17)

COMPONENT VIDEO terminals··················(9)

VIDEO/S-VIDEO terminals··························(9)

DOCK CONTROL jack ································(17)

AUDIO IN terminals·····································(9)

ANTENNA terminals ·································(16)

VIDEO SELECT/SETUP

button························(33, 47)

Input source selector

buttons····························(18)

Indicator ··························(46)

Cursor buttons

(

) ··············(11, 21)

DISPLAY button··············(47)

DIMMER/MENU

button························(19, 47)

Mode selector

switches····················(10, 46)

System buttons ·····(47 ~ 49)

!2 !1 !0 o i u y

e r t

[ Front ]

USER MODE buttons·····(33)

Getting Started Getting Started

ENGLISH

Power buttons················(47)

Input source selector/

Number buttons·······(18, 47)

SURROUND PARAMETER/

AUDIO button···········(18, 47)

ENTER button···········(21, 47)

Cursor buttons

(

)········(11, 21, 47)

INPUT MODE/RETURN

button························(18, 47)

SURROUND MODE

buttons······················(20, 28)

TEST TONE/DISPLAY

button························(45, 47)

Tuner system/System

buttons······················(30, 47)

SYSTEM SETUP/SETUP

button························(38, 47)

[ Rear ]

NOTE:

• If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated

too.

Easy Setup Procedure

ENGLISH

Speaker layout [Basic layout]

Example of basic layout with eight speakers and a monitor.

Subwoofer Center speaker

Surround speaker

Surround back speaker

Front speaker

Set these at the sides of the

monitor or screen with their front

surfaces as flush with the front of

the screen as possible.

• This section contains the basic steps necessary to configure the AVR-1707 according to your listening

room environment and the source equipment and loudspeakers you are using.

•To set the sound field manually ( page 43 ~ 45).

Easy to setup flow

Easy Setup Procedure

Auto setup flow

1) Speaker Configuration

2) Distance

3) Channel Level

Connecting a microphone ( page 10).

The measurement of the speakers in the

listening position.

Check of the measurement result.

Placing the speakers.

Connecting the speakers.

Connect the DVD player to

the AVR-1707.

Connect the AVR-1707’s

monitor output terminal to

the TV’s video input

terminal ( page 9).

Store the measurement result in the memory.

Play a DVD.

• Do not plug in the power supply cord until all connections have been completed.

><<>><<>

><><

(

) (

)

(

) (

)

(

) (

)

Easy Setup Procedure Easy Setup Procedure

ENGLISH

¢ Connections

•With the AVR-1707, up to ten speakers can be connected for surround playback.

• When making connections, also refer to the operating instructions of the other components.

When using only one surround back

speaker, connect it to the left channel.

Connection terminal for

subwoofer with built-in

amplifier.

Front speakers

(A)

Surround

speakers

Front speakers

(B)

Subwoofer

Surround back

speakers

Center

speaker

ImpedanceSpeaker

Connecting the speaker cables

Speaker connections

Connect the speaker terminals with the speakers

making sure that like polarities are matched (

with

¢ Speaker impedance

Note on speaker impedance

When using speakers with an impedance

below the designated value (for example 4

Ω/ohms), playing for long periods of time with

the volume high could cause the temperature

to rise, activating the protection circuit.

When the protection circuit is activated, the

output to the speakers is cut off and the power

indicator blinks. If this happens, unplug the

power cord, wait for the set to cool off and

improve ventilation around the unit. Also check

the wiring of the input cables and the speaker

cables. After doing this, plug the power cord

back in and turn the unit’s power back on.

If the protection circuit is activated again even

though there are no problems with the wiring or

the ventilation around the unit, switch off the

power and contact a DENON service center.

NOTE:

When making connections, take care that

none of the individual conductors of the

speaker cable come in contact with adjacent

terminals, with other speaker cable

conductors, or with the rear panel and

screws.

NEVER touch the speaker terminals when

the power is on. Doing so could result in

electric shocks.

1. Loosen by turning

counterclockwise.

Either tightly twist or terminate the core

wires.

2. Insert the cable.

3. Tighten by turning clockwise.

6 ~ 16 Ω/ohms

Center

Surround

Surround back

6 ~ 16 Ω/ohmsFront A, B

12 ~ 16 Ω/ohmsFront A+B

Easy Setup Procedure Easy Setup Procedure

ENGLISH

• For best picture quality (especially with progressive DVD and other high definition sources), choose the

component video connection to your monitor. S-Video and composite video outputs are also provided if

your monitor does not have component video inputs.

Connecting a DVD player and monitor

•To connect the video output from the DVD player to the AVR-1707, you only need to choose one

connection type. For more information about the video up conversion function ( page 13).

•To connect the digital audio output from the DVD player, you can choose from either the coaxial or

optical connections. If you choose to use the coaxial connection, it needs to be assigned. For more

information about Digital Input Assignment ( page 39).

Audio signal flow is shown with white arrows, video signal flow is shown with gray arrows.

• Connect a non-DVD video disc player (such as a laser disc, VCD/SVCD, or future high definition disc

player) to the DVD/VDP terminals in the same way.

• The component video input and/or output terminals may be labelled differently on some monitors or

video components. Check the owner’s manuals for other components for further information.

DVD player

S VIDEO

OUT

AUDIO OUT

VIDEO

OUT

COMPONENT VIDEO OUT

OPTICAL

OUT

S VIDEO

VIDEO

Monitor

COMPONENT VIDEO IN

Easy Setup Procedure Easy Setup Procedure

ENGLISH

Auto Setup

The AVR-1707’s auto setup use the attached microphone to measure

the acoustic properties in the room and automatically make the

optimum settings.

•To make the sound field settings manually ( page 43 ~ 45).

q Connecting a microphone

Connect the attached setup microphone to

SETUP

MIC

Mount the setup microphone on a camera tripod, etc.,

and set with the receptorpointing towards the ceiling.

Microphone

Place the setup microphone’s sound receptor at the height of the

ears in the listening position.

It is not possible to measure properly if there are any obstacles

between the speakers and microphone. Check that there are no

obstacles.

About the button names in this explanation

: Buttons on the main unit

[]: Buttons on the remote control unit

Button name only :

Buttons on the main unit and remote control unit

Sound receptor

Press

ON/STANDBY

or [ON/SOURCE].

• The power indicator blinks green and the power turns on.

Press

POWER

£ OFF:

The power turns off and the indicator is off.

¢ ON:

The power indicator lights red.

Turn on your subwoofer.

Set the volume to halfway and set the crossover frequency to

the maximum or Low pass filter off if your subwoofer can adjust

the output volume and the crossover frequency.

Some subwoofers have a standby mode. Be sure to turn this

function off before performing the Auto Setup procedure.

Turn on your monitor.

w Before performing the Auto Setup procedure

Set [MODE SELECTOR 1] to “AUDIO”.

• Auto Setup mode is not displayed when using headphones.

e Switching the front speaker

Press

SPEAKER

to select the front speaker (Front A,

Front B or Front A+B).

[MODE SELECTOR 1]

[ON/SOURCE]

D H F G

D H F G

<POWER>

Easy Setup Procedure Easy Setup Procedure

ENGLISH

r Starting Auto Setup

Press

to start the Auto Setup.

• Start the measurements.

Measurement of each channel is performed as follows:

Disconnect the setup mic to finish Auto Setup.

Cautions during measurements:

• Loud test tones are output during the measurements. Be careful

for example when small children are nearby.

•Proper measurements may not be possible if there are obstacles

between the speaker and the setup microphone.

• During the measurements, do not stand between or near the

speakers and setup microphone.

•To avoid influencing the measurements, turn off the power of air-

conditioners or any other equipment producing sound in the

room. Perform the measurements with the room as quiet as

possible.

•Measurement is cancelled when VOLUME is operated while the

Auto Setup is performed.

FL FR C SW SL SR

SBL SBR

1 2

1: The subwoofer speaker is measured twice.

2: Not displayed when “Front A” and “Front B” are set at

“Setting the Power Amplifier Assignment” ( page 41).

After each channel is measured, “Calculating” appears.

The display switches to the speaker check display

automatically.

M e a s u r e : F L < C c l

C a l c u l a t i n g

S p e a k e r : 3 / 4 / . 1

¢ Check the results of the speaker detection

Example: 7.1-channel systems

S p e a k e r : 3 / 4 / . 1

Subwoofer

Surround and Surround back speaker

Front and Center speaker

Press

DD HH

to select “Store”, then press

Cancel:

Cancel the checked measurement values.

Store:

Store the checked measurement values.

All parameters are stored.

Retry:

Measure again.

¢ About automatic retry

To confirm the results of the measurements, remeasurement is

automatically performed.

Remeasurement is performed up to two times. During this time,

“Retry1” or “Retry2” is displayed on the display.

O v e r l o a d R e t r y 1

• When measurements have been made using the measurement

microphone, speakers with a built-in filter such as subwoofers might

be set with a value that differs from the physical distance because

of the internal electrical delay.

NOTE:

• Do not change the speaker connections or subwoofer volume

after making the measurements.

• Do not turn off the power while the data is being stored.

S e t u p < S t o r e

S t o r i n g

A u t o S e t < S t a r t

MeasuresCauseExample

Easy Setup Procedure Easy Setup Procedure

ENGLISH

q The speakers required for producing suitable reproduction

have not been detected.

• Check that the pertinent speakers are properly

connected.

w The speaker polarity is connected in reverse.

• Check the polarity of the pertinent speakers.

• For some speakers, the screen below may be

displayed even though the speakers are properly

connected.

If so, select “Skip

”.

Error messages

An error message is displayed if the measurements could not be

completed automatically due to the speaker layout, the measuring

environment, etc. Please check the following matters, reset the

pertinent items, and measure again.

Be sure to turn off the AVR-1707’s power before checking the speaker

connections.

C a u t i o n : S P N o n e

F L

C a u t i o n : P h a s e

F L / R

e When accurate measurements cannot be made due to

the input level of the microphone being too high.

• Set up the speakers so that their position is farther

away from the listening position.

• Lower the volume of the subwoofer speaker.

C a u t i o n

O v e r l o a d < E x i t

Press

DD HH

to select the items, then press

ENGLISH

Cable indications

Signal direction

The hookup diagrams on the subsequent pages assume the use of the following optional connection cables (not supplied).

Video cableAudio cable

NOTE:

• Do not plug in the power supply cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with speaker cables. Doing so could result in humming or noise.

Analog connections (Stereo)

(Orange)

Pin-plug cable

Analog connections (Monaural, for subwoofer)

Pin-plug cable

Digital connections (Coaxial)

Coaxial cable (75 Ω/ohms pin-plug cable)

(Yellow)

Digital connections (Optical)

Optical fiber cable

Speaker connections

Speaker cable

Video connections

Video cable (75 Ω/ohms video pin-plug cable)

S-Video

connections

S-Video cable

Audio signal

Video signal

(White)

(Red)

Component video connections

Component video cable

(Y)

B/C

R/CR)

(Green)

(Blue)

(Red)

IN OUT OUT IN

Connecting Other Sources

With the AVR-1707, the Video signal and the S-Video signal which

were inputted are mutually converted. And also the Video signal and

the S-Video signal which were inputted are converted into a higher

quality.

The flow of the video signals.

This unit’s input

terminals

This unit’s output

terminals

(Component Video

terminals)

(Component Video

terminals)

(S-Video terminal)

(Video terminal)

The video conversion function

(S-Video terminal)

(Video terminal)

Connecting Other Sources Connecting Other Sources

ENGLISH

Connecting a TV/DBS tuner

• For best picture quality choose the component video connection to your TV or DBS tuner. S-Video and

composite video outputs are also provided.

•To connect the digital audio output from the TV or DBS tuner, you can choose from either the coaxial or

optical connections. If you choose to use the coaxial connection, it needs to be assigned. For more

information about Digital Input Assignment ( page 39).

TV/DBS tuner

S VIDEO

OUT

AUDIO OUT

VIDEO

OUT

COMPONENT VIDEO OUT

OPTICAL

OUT

Connecting the external inputs (EXT. IN) terminals

• These terminals are for inputting multi-channel audio signals from an outboard decoder, or a component

with a different type of multi-channel decoder, such as a DVD-Audio player, or a multi-channel Super

Audio CD player, or other future multi-channel sound format decoder.

• The video signal connection is the same as that for a DVD player ( page 9).

• For instructions on playback using the external input (EXT. IN) terminals ( page 18).

•With discs on which special copyright protection measures have been taken, however, the digital signals

may not be output from the DVD player. In this case, connect the DVD player’s analog multi-channel

output to the AVR-1707’s EXT. IN terminals for playback. Also refer to your DVD player’s operating

instructions.

DVD Audio-Video /

Super Audio CD player /

External decoder

FRONT

7.1ch AUDIO OUT

CENTER

SURROUND

BACK

SUB-

WOOFER

Connecting a video camera or video game

Video camera /

Video game

AUDIO OUT

VIDEO

OUT

Connecting Other Sources Connecting Other Sources

ENGLISH

Connecting a VCR

• For best picture quality choose the component video connection to your VCR. S-Video and composite

video outputs are also provided.

• If you wish to perform analog dubbing from a digital source, such as a DVD recorder to an analog

recorder such as a cassette deck, you will need to connect the analog inputs and outputs as shown

below, in addition to the digital audio connections.

•When recording to a VCR, it is necessary that the type of cable used with the playback source

equipment be the same type that is connected to the AVR-1707 VCR OUT terminal.

Example: TV IN → S-Video cable : VCR OUT → S-Video cable

TV IN → Video cable : VCR OUT → Video cable

Video deck

S VIDEO

OUT

S VIDEO

AUDIO IN

AUDIO OUT

VIDEO

OUT

VIDEO

COMPONENT VIDEO OUT

Connecting a tape deck, CD recorder or MD recorder

AUDIO OUT

AUDIO IN

Tape deck /

CD recorder /

MD recorder

Connecting a CD player

To connect the digital audio output from the CD player, you can choose from either the coaxial or optical

connections. If you choose to use the optical connection, it needs to be assigned. For more information

about Digital Input Assignment ( page 39).

AUDIO OUT

CD player

COAXIAL

OUT

Connecting Other Sources Connecting Other Sources

ENGLISH

¢ AM loop antenna assembly

Connect to the AM

antenna terminals.

Remove the vinyl tie

and take out the

connection line.

Bend in the reverse

direction.

a. With the antenna on

top any stable

surface.

b. With the antenna

attached to a wall.

Mount

Installation hole Mount on wall, etc.

NOTE:

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the AM loop antenna.

• Make sure the AM loop antenna lead terminals do not touch metal parts of the panel.

An FM antenna cable plug can be connected directly.

Connecting the antenna terminals

Direction of broadcasting station

75 Ω/ohms Coaxial cable

FM antenna

FM indoor antenna (Supplied)

AM loop antenna

(Supplied)

AM outdoor antenna

Ground

Connection of AM antennas

1. Push the lever.

2. Insert the conductor.

3. Return the lever.

La pagina sta caricando ...

Denon Stereo Receiver AVR-1707 Manuale utente

Marca: Denon

Modello: Stereo Receiver AVR-1707

Tipo: Manuale utente

Questo manuale è adatto anche per

AVR-1707

Scarica il pdf

rapporto

in altre lingue

English: Denon Stereo Receiver AVR-1707 User manual

Denon Stereo Receiver AVR-1707 Manuale utente

Questo manuale è adatto anche per

Denon Stereo Receiver AVR-1707 Manuale utente

in altre lingue

Documenti correlati

Altri documenti