Denon AVR-2802 Operating Instructions Manual

AV SURROUND RECEIVER

AVR-2802

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

ISTRUZIONI PER L’USO

INSTRUCCIONES DE OPERACION

GEBRUIKSAANWIJZING

BRUKSANVISNING

DVD

START LEARNED/TX

SURR.SP

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

USE/LEARN T.TONE MULTI OUTPUT SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS V.AUX PHONO

VCR-1 CD

CDR

/

TAPE

CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

MASTER VOLUME

FUNCTION

TUNING

PRESET

REC /

MULTI

6.1 / 7.1

SURROUND

SOURCE

AVR-2802

PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER

VOLUME LEVEL

STAND BY

REMOTE

SENSOR

B

PHONES

CH VOLSURROUND

MODE

SURROUND

PARAMETER

ON/STANDBY

¢

OFF£

TONE

CONTROL

SELECT

INPUT

DIMMER

EXT. IN

ANALOG

INPUT MODE

A

B

STATUS

VIDEO SELECT

SPEAKER

TONE DEFEAT

OUTPUT

SIGNAL

DETECT

SURROUND

BACK CH

AUTO

PCM

DTS

SIGNAL

DIGITAL

INPUT

FOR ENGLISH READERS PAGE 112 ~ PAGE 138

FÜR DEUTSCHE LESER SEITE 139 ~ SEITE 174

POUR LES LECTEURS FRANCAIS PAGE 175 ~ PAGE 110

PER IL LETTORE ITALIANO PAGINA 111 ~ PAGINA 146

PARA LECTORES DE ESPAÑOL PAGINA 147 ~ PAGINA 182

VOOR NEDERLANDSTALIGE LEZERS PAGINA 183 ~ PAGINA 218

FOR SVENSKA LÄSARE SIDA 219 ~ SIDA 254

2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product, to which this declaration relates, is in conformity

with the following standards:

EN60065, EN55013, EN55020, EN61000-3-2 and

EN61000-3-3.

Following the provisions of 73/23/EEC, 89/336/EEC and

93/68/EEC Directive.

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses

Produkt, auf das sich diese Erklärung bezieht, den

folgenden Standards entspricht:

EN60065, EN55013, EN55020, EN61000-3-2 und

EN61000-3-3.

Entspricht den Verordnungen der Direktive 73/23/EEC,

89/336/EEC und 93/68/EEC.

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que

l’appareil, auquel se réfère cette déclaration, est

conforme aux standards suivants:

EN60065, EN55013, EN55020, EN61000-3-2 et

EN61000-3-3.

D’après les dispositions de la Directive 73/23/EEC,

89/336/EEC et 93/68/EEC.

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo

prodotto, al quale la nostra dichiarazione si riferisce, è

conforme alle seguenti normative:

EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-

3-3.

In conformità con le condizioni delle direttive 73/23/EEC,

89/336/EEC e 93/68/EEC.

QUESTO PRODOTTO E’ CONFORME

AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que

este producto al que hace referencia esta declaración,

está conforme con los siguientes estándares:

EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-

3-3.

Siguiendo las provisiones de las Directivas 73/23/EEC,

89/336/EEC y 93/68/EEC.

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid

dat dit produkt, waarop deze verklaring betrekking heeft,

in overeenstemming is met de volgende normen:

EN60065, EN55013, EN55020, EN61000-3-2 en

EN61000-3-3.

Volgens de bepalingen van de Richtlijnen 73/23/EEC,

89/336/EEC en 93/68/EEC.

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt,

vilken detta intyg avser, uppfyller följande standarder:

EN60065, EN55013, EN55020, EN61000-3-2 och

EN61000-3-3.

Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC och

93/68/EEC.

NOTE ON USE / HINWEISE ZUM GEBRAUCH /

OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA

• Avoid high temperatures.

Allow for sufficient heat dispersion when

installed on a rack.

• Vermeiden Sie hohe Temperaturen.

Beachten Sie, daß eine ausreichend

Luftzirkulation gewährleistet wird, wenn das

Gerät auf ein Regal gestellt wird.

• Eviter des températures élevées

Tenir compte d’une dispersion de chaleur

suffisante lors de l’installation sur une

étagère.

• Evitate di esporre l’unità a temperature alte.

Assicuratevi che ci sia un’adeguata

dispersione del calore quando installate

l’unità in un mobile per componenti audio.

• Evite altas temperaturas

Permite la suficiente dispersión del calor

cuando está instalado en la consola.

• Vermijd hoge temperaturen.

Zorg voor een degelijk hitteafvoer indien het

apparaat op een rek wordt geplaatst.

• Undvik höga temperaturer.

Se till att det finns möjlighet till god

värmeavledning vid montering i ett rack.

• Keep the set free from moisture, water, and

dust.

• Halten Sie das Gerät von Feuchtigkeit,

Wasser und Staub fern.

• Protéger l’appareil contre l’humidité, l’eau et

lapoussière.

• Tenete l’unità lontana dall’umidità, dall’acqua

e dalla polvere.

• Mantenga el equipo libre de humedad, agua

y polvo.

• Laat geen vochtigheid, water of stof in het

apparaat binnendringen.

• Utsätt inte apparaten för fukt, vatten och

damm.

• Do not let foreign objects in the set.

• Keine fremden Gegenstände in das Gerät

kommen lassen.

• Ne pas laisser des objets étrangers dans

l’appareil.

• E’ importante che nessun oggetto è inserito

all’interno dell’unità.

• No deje objetos extraños dentro del equipo.

• Laat geen vreemde voorwerpen in dit

apparaat vallen.

• Se till att främmande föremål inte tränger in i

apparaten.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Gehen Sie vorsichtig mit dem Netzkabel um.

Halten Sie das Kabel am Stecker, wenn Sie

den Stecker herausziehen.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Manneggiate il filo di alimentazione con cura.

Agite per la spina quando scollegate il cavo

dalla presa.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el

cordón de energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast wanneer

deze moet worden aan- of losgekoppeld.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-uttaget.

• Unplug the power cord when not using the

set for long periods of time.

• Wenn das Gerät eine längere Zeit nicht

verwendet werden soll, trennen Sie das

Netzkabel vom Netzstecker.

• Débrancher le cordon d’alimentation lorsque

l’appareil n’est pas utilisé pendant de

longues périodes.

• Disinnestate il filo di alimentazione quando

avete l’intenzione di non usare il filo di

alimentazione per un lungo periodo di tempo.

• Desconecte el cordón de energía cuando no

utilice el equipo por mucho tiempo.

• Neem altijd het netsnoer uit het stopkontakt

wanneer het apparaat gedurende een lange

periode niet wordt gebruikt.

• Koppla ur nätkabeln om apparaten inte

kommer att användas i lång tid.

• Do not let insecticides, benzene, and thinner

come in contact with the set.

• Lassen Sie das Gerät nicht mit Insektiziden,

Benzin oder Verdünnungsmitteln in

Berührung kommen.

• Ne pas mettre en contact des insecticides,

du benzène et un diluant avec l’appareil.

• Assicuratevvi che l’unità non venga in

contatto con insetticidi, benzolo o solventi.

• No permita el contacto de insecticidas,

gasolina y diluyentes con el equipo.

• Laat geen insektenverdelgende middelen,

benzine of verfverdunner met dit apparaat in

kontakt komen.

• Se till att inte insektsmedel på spraybruk,

bensen och thinner kommer i kontakt med

apparatens hölje.

• Never disassemble or modify the set in any

way.

• Versuchen Sie niemals das Gerät

auseinander zu nehmen oder auf jegliche Art

zu verändern.

• Ne jamais démonter ou modifier l’appareil

d’une manière ou d’une autre.

• Non smontate mai, nè modificate l’unità in

nessun modo.

• Nunca desarme o modifique el equipo de

ninguna manera.

• Nooit dit apparaat demonteren of op andere

wijze modifiëren.

• Ta inte isär apparaten och försök inte bygga

om den.

• Do not obstruct the ventilation holes.

• Die Belüftungsöffnungen dürfen nicht

verdeckt werden.

• Ne pas obstruer les trous d’aération.

• Non coprite i fori di ventilazione.

• No obstruya los orificios de ventilación.

• De ventilatieopeningen mogen niet worden

beblokkeerd.

• Täpp inte till ventilationsöppningarna.

* (For sets with ventilation holes)

CAUTION

• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths,

curtains, etc.

• No naked flame sources, such as lighted candles, should be placed on the apparatus.

• Please be care the environmental aspects of battery disposal.

• The apparatus shall not be exposed to dripping or splashing for use.

• No objects filled with liquids, such as vases, shall be placed on the apparatus.

ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

3

ENGLISH

2 We greatly appreciate your purchase of the AVR-2802.

2 To be sure you take maximum advantage of all the features the AVR-2802 has to offer, read these

instructions carefully and use the set properly. Be sure to keep this manual for future reference,

should any questions or problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE

CABINET FOR FUTURE REFERENCE”

2 INTRODUCTION

Thank you for choosing the DENON AVR-2802 Digital Surround A / V receiver. This remarkable component has

been engineered to provide superb surround sound listening with home theater sources such as DVD, as well as

providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and

operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

z

Before Using........................................................3

x

Cautions on Installation........................................3

c

Cautions on Handling...........................................3

v

Features...............................................................4

b

Connections.....................................................4~8

n

Part Names and Functions ..............................8, 9

m

Setting up the system...................................9~14

,

Remote Control Unit ...................................15~19

.

Operation.....................................................20~23

⁄0

Surround......................................................24~26

⁄1

DSP Surround Simulation............................27~29

⁄2

Listening to the Radio .................................30~32

⁄3

Last Function Memory.......................................33

⁄4

Initialization of the Microprocessor....................33

⁄5

Troubleshooting ...........................................33, 34

⁄6

Additional Information .................................34~38

⁄7

Specifications.....................................................38

2

ACCESSORIES

Check that the following parts are included in addition to the main unit:

erty

q Operating instructions........................................1

w Service station list..............................................1

e Remote control unit (RC-904) ............................1

r R6P/AA batteries................................................2

t AM loop antenna................................................1

y FM indoor antenna.............................................1

1

BEFORE USING

Pay attention to the following before using this

unit:

• Moving the set

To prevent short circuits or damaged wires in the

connection cords, always unplug the power cord

and disconnect the connection cords between all

other audio components when moving the set.

• Before turning the power switch on

Check once again that all connections are proper

and that there are not problems with the connection

cords. Always set the power switch to the standby

position before connecting and disconnecting

connection cords.

• Store this instructions in a safe place.

After reading, store this instructions along with the

warranty in a safe place.

• Note that the illustrations in this instructions

may differ from the actual set for explanation

purposes.

Noise or disturbance of the picture may be generated

if this unit or any other electronic equipment using

microprocessors is used near a tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or

TV.

• Set the antenna wires from the tuner or TV away

from this unit’s power cord and input/output

connection cords.

• Noise or disturbance tends to occur particularly

when using indoor antennas or 300 Ω/ohms feeder

wires. We recommend using outdoor antennas

and 75 Ω/ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space

between the top, back and sides of this unit

and the wall or other components.

B

10 cm or more

wall

10 cm or more

2

CAUTIONS ON INSTALLATION

• Switching the input function when input jacks

are not connected

A clicking noise may be produced if the input

function is switched when nothing is connected to

the input jacks. If this happens, either turn down the

MASTER VOLUME control or connect components

to the input jacks.

• Muting of PRE OUT jacks, HEADPHONE jack and

SPEAKER terminals

The PRE OUT jacks, HEADPHONE jack and

SPEAKER terminals include a muting circuit.

Because of this, the output signals are greatly

reduced for several seconds after the power switch

is turned on or input function, surround mode or any

other-set-up is changed. If the volume is turned up

during this time, the output will be very high after

the muting circuit stops functioning. Always wait

until the muting circuit turns off before adjusting the

volume.

• Whenever the power switch is in the

£ OFF

state, the apparatus is still connected on AC line

voltage.

Please be sure to unplug the cord when you

leave home for, say, a vacation.

3

CAUTIONS ON HANDLING

4

ENGLISH

4

FEATURES

1. Multi Room Music Entertainment System

Multi Source Function:

This unit’s Multi Source function lets you select

different audio or video sources for viewing or

listening Different sources can thus be enjoyed

in the main room and the subroom

simultaneously.

2. Dolby Pro Logic II decoder

Dolby Pro Logic II is a new format for playing

multichannel audio signals that offers

improvements over conventional Dolby Pro Logic.

It can be used to decode not only sources

recorded in Dolby Surround but also regular stereo

sources into five channels (front left/right, center

and surround left/right). In addition, various

parameters can be set according to the type of

source and the contents, so you can adjust the

sound field with greater precision.

3. Dolby Digital

Using advanced digital processing algorithms,

Dolby Digital provides up to 5.1 channels of wide-

range, high fidelity surround sound. Dolby Digital

is the default digital audio delivery system for

North American DVD and DTV.

4. DTS (Digital Theater Systems)

DTS provides up to 5.1 channels of wide-range,

high fidelity surround sound, from sources such as

laser disc, DVD and specially-encoded music

discs.

5. DTS-ES Extended Surround and DTS Neo:6

The AVR-2802 is compatible with DTS-ES Extended

Surround, a new multi-channel format developed by

Digital Theater Systems Inc.

The AVR-2802 is also compatible with DTS Neo:6, a

surround mode allowing 6.1-channel playback of

regular stereo sources.

6. Component Video Switching

In addition to composite video and “S” video

switching, the AVR-2802 provides 2 sets of

component video (Y, P

B

/CB, PR/CR) inputs for the

DVD and TV/DBS inputs, and one set of

component video outputs to the television, for

superior picture quality.

7. Video Select Function

Allow you to watch one source (visual) while

listening to another source (audio).

• Do not plug in the AC cord until all connections

have been completed.

• Be sure to connect the left and right channels

properly (left with left, right with right).

• Insert the plugs securely. Incomplete connections

will result in the generation of noise.

• Use the AC OUTLET for audio equipment only.

Do not use them for hair driers, etc.

• Note that binding pin plug cords together with AC

cords or placing them near a power transformer

will result in generating hum or other noise.

• Noise or humming may be generated if a

connected audio equipment is used independently

without turning the power of this unit on. If this

happens, turn on the power of the this unit

.

Connecting the audio components

5

CONNECTIONS

R

L

R

L

R

INPUT OUTPUT

LRL

R

OUTPUT

L

R

L

INPUT

OPTICAL COAXIAL

OUTPUT

OPTICAL

L

R

L

R

L

R

L

R

OUTPUT

DIGITAL AUDIODIGITAL AUDIO

B

CD player

Connecting a CD player

Connect the CD player’s

analog output jacks

(ANALOG OUTPUT) to this

unit’s CD jacks using pin

plug cords.

Connecting a turntable

Connect the turntable’s output cord to the

AVR-2802’s PHONO jacks, the L (left) plug to

the L jack, the R (right) plug to the right jack.

NOTES:

• This unit cannot be used with MC

cartridges directly. Use a separate head

amplifier or step-up transformer.

• If humming or other noise is generated

when the ground wire is connected,

disconnect the ground wire.

Turntable

(MM cartridge)

Ground

wire

Use these jacks if you wish to connect external power

amplifier(s) to increase the power of the front, center,

surround and surround back sound channels, or for

connection to powered loudspeakers.

To use Surround back with one speaker, connect the

speaker to SURR. BACK L CH.

MD recorder, CD recorder or other component

equipped with digital input/output jacks

CD player or other component equipped

with digital output jacks

Connecting the DIGITAL jacks

Use these for connections to audio equipment with digital output. Refer to

page 13 for instructions on setting this terminal.

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s

tape recording (CDR/TAPE OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this

unit’s tape playback (CDR/TAPE IN) jacks using pin plug cords.

CD recorder or Tape deck

• When making connections, also refer to the operating instructions of the other components.

The power to this outlet is turned on and off when the power is switched between on and standby from the

remote control unit or power switch.

NOTES:

• Use 75 Ω/ohms cable pin cords for coaxial connections.

• Use optical cables for optical connections, removing the cap before

connecting.

Power supply cord

AC 230V, 50Hz

Connecting the AC OUTLET

AC OUTLET

• SWITCHED

(total capacity – 100 W)

The power to this outlet is turned on and off in conjunction with the

POWER operation switch on the main unit, and when the power is

switched between on and standby from the remote control unit.

No power is supplied from this outlet when this unit’s power is at

standby. Never connect equipment whose total capacity is above 100

W.

NOTE:

Only use the AC OUTLET for audio equipment. Never use them for

hair driers, TVs or other electrical appliances.

Route the connection cords, etc., in

such a way that they do not

obstruct the ventilation holes.

NOTE:

If humming noise is generated

by a tape deck, etc., move the

tape deck away.

Connecting the pre-out jacks

5

ENGLISH

Connecting video components

• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can

result in a drop in video quality.

• When making connections, also refer to the operating instructions of the other components.

IN

VIDEO

R

L

ROUTIN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT

VIDEO

OUT

L

AUDIO

L

R

R OUT

VIDEO

OUT

L

AUDIO

L

R

L

R

L

R

L

R

L

RL

B

TV or DBS tuner

DVD player or video disc player (VDP), etc.

Monitor TV

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT)

to the (yellow) TV/DBS IN jack using a 75 Ω/ohms video

coaxial pin plug cord.

• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT)

to the TV/DBS IN jacks using pin plug cords.

AUDIO

VIDEO

Connecting a DVD player or a video disc player (VDP)

MONITOR OUT

• Connect the TV’s video

input jack (VIDEO

INPUT) to the

MONITOR OUT jack

using a 75 Ω/ohms

video coaxial pin plug

cord.

VIDEO

Note on connecting the digital input

jacks

• Only audio signals are input to the

digital input jacks. For details, see page

4.

Video deck 2

Video deck 1

• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the

(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.

Connecting the audio output jacks

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the

VCR-1 OUT jacks using pin plug cords.

Connect the second video deck to the VCR-2/V.AUX jacks in the same way.

AUDIOAUDIO

VIDEO

Connecting a video decks

DVD

• Connect the DVD player’s video output jack (VIDEO OUTPUT) to the

(yellow) DVD IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the DVD player’s analog audio output jacks (ANALOG AUDIO OUTPUT)

to the DVD IN jacks using pin plug cords.

• A video disc player can be connected to the VDP jacks in the same way.

• It is also possible to connect a video disc player, DVD player, video camcorder,

game machine, etc., to the VCR-2/V.AUX jacks.

AUDIO

VIDEO

IN

S-VIDEO

OUT

S-VIDEO

OUT

S-VIDEO

OUT IN

S-VIDEO

OUT IN

S-VIDEO

B

DVD player or video disc player (VDP)

Monitor TV

Video deck 2

Video deck 1

TV or satellite broadcast tuner

Connecting a DVD player or a video disc player (VDP)

Connecting a monitor TV

Connecting the video decks

Connecting a TV/DBS tuner

DVD

• Connect the DVD player’s S-Video output jack to the S-

VIDEO DVD IN jack using an S-Video connection cord.

• A VDP can be connected to the VDP jacks in the same way.

• It is also possible to connect a video disc player, DVD player,

video camcorder, game machine, etc., to the VCR-2/V.AUX

jacks.

MONITOR OUT

• Connect the TV’s S video input (S-VIDEO INPUT) to the

MONITOR OUT jack using a S jack connection cord.

S-VIDEO

• Connect the TV’s or DBS tuner’s S video output jack (S-

VIDEO OUTPUT) to the TV/DBS IN jack using a

S jack connection cord.

S-VIDEO

• Connect the video deck’s S output jack (S-OUT) to the

VCR-1 IN jack and the video deck’s S input jack (S-IN) to the

VCR-1 OUT jack using S jack connection cords.

• Connect the video deck’s S output jack (S-OUT) to the

VCR-2/V.AUX IN jack and the video deck’s S input jack (S-IN) to

the VCR-2/V.AUX OUT jack using S jack connection

cords.

S-VIDEO

Connecting a video component equipped with S-Video jacks

• When making connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit

structures, so that video signals input from the S-jacks are only output from the S-jack outputs and video

signals input from the pin jacks are only output from the pin jack outputs.

When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and

make connections according to the equipment’s instruction manuals.

Connecting a monitor

TV

6

ENGLISH

Connecting the antenna terminals

DIRECTION OF

BROADCASTING

STATION

75 Ω/ohms

COAXIAL

CABLE

FM ANTENNA

FM INDOOR

ANTENNA

(Supplied)

AM LOOP

ANTENNA

(Supplied)

AM OUTDOOR

ANTENNA

GROUND

1

4

2

3

AM loop antenna assembly

Connect to the AM

antenna terminals.

Remove the vinyl tie

and take out the

connection line.

Bend in the reverse

direction.

a. With the

antenna on

top any

stable

surface.

b. With the

antenna

attached to

a wall.

Mount

Installation hole Mount on wall, etc.

Connection of AM antennas

1. Push the

lever.

2. Insert the

conductor.

3. Return the

lever.

Notes:

• Do not connect two FM antennas

simultaneously.

• Even if an external AM antenna is used, do

not disconnect the AM loop antenna.

• Make sure AM loop antenna lead terminals

do not touch metal parts of the panel.

Y CRCB

VIDEO OUT

Y

CR CB

COMPONENT

VIDEO IN

COMPONENT

B

DVD player

Monitor TV

Connecting a DVD player

Connecting a monitor TV

DVD IN jacks

• Connect the DVD player’s color difference (component)

video output jacks (COMPONENT VIDEO OUTPUT) to the

COMPONENT DVD IN jack using 75 Ω/ohms coaxial video

pin-plug cords.

• In the same way, another video source with component

video outputs such as a TV/DBS tuner, etc., can be connected

to the TV/DBS color difference (component) video jacks.

MONITOR OUT jack

• Connect the TV’s color difference (component)

video input jacks (COMPONENT VIDEO INPUT)

to the COMPONENT MONITOR OUT jack using

75 Ω/ohms coaxial video pin-plug cords.

• The color difference input jacks may be indicated differently on some

TVs, monitors or video components (“CR, CB and Y”, “R-Y, B-Y and Y”,

“Pr, Pb and Y”, etc.). For details, carefully read the operating instructions

included with the TV or other component.

Connecting a Video Component Equipped with Color Difference (Component

- Y, P

R

/C

R

, P

B

/C

B

) Video Jacks (DVD Player)

• When making connections, also refer to the operating instructions of the other components.

• The signals input to the color difference (component) video jacks are not output from the VIDEO output jack

(yellow) or the S-Video output jack. In addition, the video signals input to the VIDEO input (yellow) and S-Video

input jacks are not output to the color difference (component) video jacks.

• The AVR-2802’s on-screen display signals are not output from the color difference (component) video output

jacks (MONITOR OUT).

• Some video sources with component video outputs are labeled Y, C

B, CR, or Y, P

b, Pr, or Y, R-Y, B-Y. These

terms all refer to component video color difference output.

7

ENGLISH

L

R

L

R

Decoder with 6-channel

analog output

Front

Surround

Subwoofer

Center

For instructions on playback using the external input (EXT. IN) jacks, see page 21.

Connecting the external input (EXT. IN) jacks

• These jacks are for inputting multi-channel audio signals from an outboard decoder, or a component with a

different type of multi-channel decoder, such as a DVD Audio player, or a multi-channel SACD player, or other

future multi-channel sound format decoder.

• When making connections, also refer to the operating instructions of the other components.

R

L

B

Another room

Integrated pre-main amplifier

For instructions on operations using the MULTI ZONE jacks, see page 23.

Connecting the MULTI ZONE jacks

• If another pre-main (integrated) amplifier is connected, the multi-zone jacks can be used to play a different

program source in another room at the same time.

Speaker Impedance

• Speakers with an impedance of from 6 to 16

Ω/ohms can be connected for use as front and

center speakers.

• Speakers with an impedance of 6 to 16 Ω/ohms

can be connected for use as surround and surround

back speakers.

• Be careful when using two pairs of front speakers

(A + B) at the same time, since use of speakers

with an impedance of less than 8 Ω/ohms will lead

to damage.

• The protector circuit may be activated if the set is

played for long periods of time at high volumes

when speakers with an impedance lower than the

specified impedance are connected.

NOTE:

NEVER touch the speaker terminals when the

power is on.

Doing so could result in electric shocks.

Connecting the speaker cords

1. Loosen by turning

counterclockwise.

2. Insert the cord. 3. Tighten by turning

clockwise.

Speaker system connections

• Connect the speaker terminals with the speakers

making sure that like polarities are matched ( <

with < , > with > ). Mismatching of polarities will

result in weak central sound, unclear orientation of

the various instruments, and the sense of direction

of the stereo being impaired.

• When making connections, take care that none of

the individual conductors of the speaker cord come

in contact with adjacent terminals, with other

speaker cord conductors, or with the rear panel.

Protector circuit

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the

speakers under circumstances such as when the output of the power amplifier is inadvertently short-

circuited and a large current flows, when the temperature surrounding the unit becomes unusually high,

or when the unit is used at high output over a long period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED

flashes. Should this occur, please follow these steps: be sure to switch off the power of this unit, check

whether there are any faults with the wiring of the speaker cables or input cables, and wait for the unit to

cool down if it is very hot. Improve the ventilation condition around the unit and switch the power back

on.

If the protection circuit is activated again even though there are no problems with the wiring or the

ventilation around the unit, switch off the power and contact a DENON service center.

Note on speaker impedance

• The protector circuit may be activated if the set is played for long periods of time at high volumes when

speakers with an impedance lower than the specified impedance (for example speakers with an

impedance of lower than 4 Ω/ohms) are connected. If the protector circuit is activated, the speaker output

is cut off. Turn off the set’s power, wait for the set to cool down, improve the ventilation around the set,

then turn the power back on.

8

ENGLISH

Connections

• When making connections, also refer to the operating instructions of the other components.

(

L

)

(

L

) (

R

)

(

R

)

(

L

) (

R

) (

L

) (

R

)

L

R

B

Connection jack for

subwoofer with built-in

amplifier (super woofer),

etc.

SURROUND BACK

SPEAKER SYSTEMS

CENTER SPEAKER

SYSTEM

FRONT SPEAKER

SYSTEMS (B)

• Precautions when connecting speakers

If a speaker is placed near a TV or video monitor, the colors on the screen may be disturbed by the

speaker’s magnetism. If this should happen, move the speaker away to a position where it does not have

this effect.

SURROUND SPEAKER

SYSTEMS

SURROUND BACK SPEAKER SYSTEMS

AVR-2802

PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER

OUTPUT

SIGNAL

DETECT

SURROUND

BACK CH

TUNING

PRESET

REC /

MULTI

6.1 / 7.1

SURROUND

SOURCE

ON / STANDBY

REMOTE

SENSOR

FUNCTION

AUTO

PCM

DTS

SIGNAL

DIGITAL

INPUT

VOLUME LEVEL

MASTER VOLUME

SURROUND

MODE

SURROUND

PARAMETER

TONE

CONTROL

SELECT CH VOL

DIMMER

STATUS TONE DEFEAT

VIDEO SELECT

INPUTSPEAKER

EXT. IN

ANALOG

AB

INPUT MODE

PHONES

ON / STANDBY

OFF

£

¢

!6

!7!8!9@0@1@2@3@4@5@6@7

q wre t y u

io!0 !1 !2 !3 !4 !5

Front Panel

6

PART NAMES AND FUNCTIONS

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

q

Power operation switch .................................(20)

w

Headphones jack (PHONES) ..........................(22)

e

6.1/7.1 SURROUND button............................(26)

r

Front speaker system selecter buttons

(SPEAKER A/B)...............................................(20)

t

INPUT MODE button .....................................(20)

y

ANALOG button .............................................(20)

u

EXT. IN button ................................................(20)

i

VIDEO SELECT button ...................................(22)

o

DIMMER button.............................................(22)

!0

STATUS button ...............................................(22)

!1

TONE DEFEAT button ....................................(22)

!2

SURROUND MODE button............................(21)

!3

SURROUND PARAMETER button .................(25)

!4

SELECT knob..................................................(21)

!5

TONE CONTROL button ................................(22)

!6

CH VOL button...............................................(24)

!7

MASTER VOLUME control ............................(21)

!8

Master volume indicator (VOLUME LEVEL) ..(21)

!9

Display

@0

INPUT mode indicators ..................................(21)

@1

SIGNAL indicators ..........................................(21)

@2

Remote control sensor

(REMOTE SENSOR).......................................(15)

@3

Power indicator ..............................................(20)

@4

FUNCTION knob.............................................(20)

@5

TUNING PRESET button ................................(31)

@6

SOURCE selector button ...............................(20)

@7

REC/MULTI button .........................................(23)

FRONT SPEAKER

SYSTEMS (A)

Integrated amplifier or Power

amplifier

NOTE:

When using two surround back speakers,

connect the integrated pre-main amplifier

to the pre-out jacks (SBL and SBR).

9

ENGLISH

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH/6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

CDR

/

TAPE

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

SYSTEM SETUP button ...............(10)

Test tone button...........................(24)

Surround buttons .........................(21)

Tuner system buttons..................(15)

System buttons............................(15)

Multi source button .....................(23)

INPUT MODE selector

buttons.........................................(20)

Mode selector

switches.......................................(15)

Input source selector

buttons.........................................(20)

Master volume control

buttons.........................................(21)

Tuner buttons...............................(15)

Power button ...............................(20)

MUTING button ...........................(22)

SURROUND PARAMETER

button...........................................(25)

Cursor buttons .............................(10)

STATUS button.............................(22)

Remote control signal

transmitter ...................................(15)

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI

RETURN

DVD

SET UP

STATUS

DISPLAY

ON SCREEN

MUTING

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

ENTER

7

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS”

(see pages 4 to 8), make the various settings described below on the monitor screen using the AVR-2802’s

on-screen display function.

These settings are required to set up the listening room’s AV system centered around the AVR-2802.

• Use the following buttons to set up the system:

• System setup items and default values (set upon shipment from the factory)

System setup Default settings

q

w

r

t

y

Speaker

Configuration

Subwoofer

mode

SB CH Auto

Flag Detect

Channel Level

Digital In

Assignment

On Screen

Display

Input the combination of speakers in your system and their

corresponding sizes (SMALL for regular speakers, LARGE for

full-size, full-range) to automatically set the composition of the

signals output from the speakers and the frequency response.

This selects the subwoofer speaker for playing deep bass

signals.

Set the method of playing the surround backchannel for digital

signals.

This adjusts the volume of the signals output from the speakers

and subwoofer for the different channels in order to obtain

optimum effects.

This assigns the digital input jacks for the different

input sources.

This sets whether or not to display the on-screen display that

appears on the monitor screen when the controls on the remote

control unit or main unit are operated.

Input

source

Digital

Inputs

Front Sp.

Large

Center Sp. Surround Sp.SubWoofer

Small SmallYes

LFE

Front L & R Center Surround L & RSub Woofer

3.6 m (12 ft) 3.6 m (12 ft) 3.0 m (10 ft)3.6 m (12 ft)

Front L

Front R Center

Surround

R

—Subwoofer

0 dB 0 dB 0 dB 0 dB —0 dB

CD DVD TV/DBS

CDR

/TAPE

VDP —

COAXIAL

OPTICAL

1

OPTICAL

2

OPTICAL

3

OFF —

On Screen Display = ON

Surround Back Sp.

Small / 1spkr

DTS-ES / 6.1 Source Auto Flag Detect Mode = OFF

e

Delay Time

This parameter is for optimizing the timing with which the

audio signals are produced from the speakers and subwoofer

according to the listening position.

Surround Back

3.0 m (10 ft)

Surround

Back

0 dB

Surround

L

0 dB

VCR-2

OFF

VCR-1

OFF

A1 ~ A8 87.5 / 89.1 / 98.1 / 108.0 / 90.1 / 90.1 / 90.1 / 90.1 MHz

B1 ~ B8 522 / 603 / 999 / 1404 / 1611 kHz, 90.1 / 90.1 / 90.1 MHz

C1 ~ C8 90.1 MHz

D1 ~ D8 90.1 MHz

E1 ~ E8 90.1 MHz

u

Auto Tuner

Preset

FM stations are received automatically and stored in the

memory.

Crossover

Frequency

Set the frequency (Hz) below which the bass sound of the

various speakers is to be output from the subwoofer.

80 Hz

ON SCREEN button .....................(22)

DVD SETUP button......................(17)

Channel select/enter

button...........................................(10)

LEDs (indicators)..........................(19)

SYSTEM CALL buttons................(18)

SPEAKER select button..............(20)

USE/LEARN selector

button...........................................(18)

NOTES:

• The shaded buttons do not function with the AVR-2802.

(Nothing happens when they are pressed.)

• The button indicated , however, can be used with the learning function.

SYSTEM SETUP button

Press this to display the system setup menu.

ENTER button

Press this to switch the display on the screen.

Also use this button to complete the setting on the screen.

CURSOR buttons

and : Use these to move the cursors (

0 and 1) to

the left and right on the screen.

and : Use these to move the cursors (• and ª) up

and down on the screen.

10

ENGLISH

NOTES:

• The on-screen display signals are not output from the color difference (component) video signal

(MONITOR OUT) jacks.

• The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack during playback

of a video component. For example, if the TV monitor is connected to both the AVR-2802’s S-Video and

video monitor output jacks and signals are input to the AVR-2802 from a video source (VDP, etc.) connected

to both the S-Video and video input jacks, the on-screen display signals are output with priority to the S-

Video monitor output. If you wish to output the signals to the video monitor output jack, do not connect a

cord to the S-VIDEO MONITOR OUT jack. (For details, see page 14.)

• The AVR-2802’s on-screen display function is designed for use with high resolution monitor TVs, so it may

be difficult to read small characters on TVs with small screens or low resolutions.

• The setup menu is not displayed when “HEADPHONE ONLY” is selected.

• Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of eight speaker systems and a

television monitor:

Subwoofer Center speaker system

Surround speaker systems

Surround back speaker system

Front speaker systems

Set these at the sides of the TV or

screen with their front surfaces as flush

with the front of the screen as possible.

Before setting up the system

2

Display the System Setup Menu.

TITLE

SYSTEM

SETUP

1

Check that all the connections are correct, then turn on the main unit’s power.

• The composition of the signals output from the different channels and the frequency response are adjusted

automatically according to the combination of speakers actually being used.

Setting the type of speakers

1

At the System Setup Menu select “Speaker Configuration”.

2

Switch to the speaker configuration screen.

ENTER

Center Sp.

Front Sp.

Subwoofer

Surround Sp.

Surround back Sp.

NOTES:

• Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s

capacity for playing low frequency (bass sound below frequency set for the Crossover Frequency mode and

below) signals. If you do not know, try comparing the sound at both settings (setting the volume to a level

low enough so as not to damage the speakers) to determine the proper setting.

• When “2spkrs” is selected for the surround back channel, and external integrated pre-main amplifier or

power amplifier must be connected to the pre-out jacks (SBL and SBR). (See page 8.)

3

Set whether or not speakers

are connected and, if so, their

size parameters.

• To select the speaker

• To select the parameter

4

Press the ENTER button to finalize the setting.

ENTER

• Parameters

Large.................Select this when using speakers that have sufficient performance for reproducing bass

sound below the frequency set for the Crossover Frequency mode.

Small.................Select this when using speakers that do not have sufficient performance for reproducing

bass sound below the frequency set for the Crossover Frequency mode. When this is set,

bass sound with a frequency below the frequency set for the Crossover Frequency mode

is sent to the subwoofer.

When this setting is selected, low frequencies of below the frequency set for the Crossover

Frequency mode are assigned to the subwoofer.

None……..........Select this when no speakers are installed.

Yes/No… ...........Select “Ye s” when a subwoofer is installed, “No” when a subwoofer is not installed.

2spkrs/1spkr .....Set the number of speakers to be used for the surround back channel.

If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when

“Small” is set for the front, center and surround speakers.

For the majority of speaker system configurations, using the Small setting for all five main speakers and

Subwoofer On with a connected subwoofer will yield the best results.

11

ENGLISH

Setting the Crossover Frequency and Subwoofer mode

1

Select the “Crossover Frequency” mode.

3

Enter the setting.

The System Setup Menu reappears.

ENTER

This screen is not displayed when not using a subwoofer.

• Set the crossover frequency and subwoofer mode according to the speaker system being used.

Select the Frequency.

2

Select the “Subwoofer Mode”.

Select the setting.

The subwoofer mode setting is only valid when “Large” is set for the front speakers and “Yes ” is set

for the subwoofer in the “Speaker Configuration” settings (see page 10).

NOTES:

— Assignment of low frequency signal range —

• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or

DTS signals) and the low frequency signal range of channels set to “Small” in the setup menu. The low

frequency signal range of channels set to “Large” are produced from those channels.

— Crossover Frequency —

• When “Subwoofer” is set to “Ye s” at the “Speaker Configuration Setting”, set the frequency (Hz) below

which the bass sound of the various speakers is to be output from the subwoofer (the crossover

frequency).

• For speakers set to “Small”, sound with a frequency below the crossover frequency is cut, and the cut bass

sound is output from the subwoofer instead.

NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When

using small speakers, however, setting the crossover frequency to a high frequency may improve

frequency response for frequencies near the crossover frequency.

— Subwoofer mode —

• When the “LFE+MAIN” playback mode is selected, the low frequency signal range of channels set to

“Large” are produced simultaneously from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending

on the size and shape of the room, interference may result in a decrease of the actual volume of the low

frequency range.

• Selection of the “LFE ” play mode will play the low frequency signal range of the channel selected with

“Large” from that channel only. Therefore, the low frequency signal range that are played from the

subwoofer channel are only the low frequency signal range of LFE (only during Dolby Digital or DTS signal

playback) and the channel specified as “Small” in the setup menu.

• Select the play mode that provides bass reproduction with body.

• When the subwoofer is set to “Ye s”, bass sound is output from the subwoofer regardless of the subwoofer

mode setting in surround modes other than Dolby/DTS.

Set the operation for the digital signals when playing in the 6.1 SURROUND and DTS-ES surround modes.

Setting the SB CH Auto Flag Detect

1

At the System Setup Menu select “SB CH

Auto Flag Detect” and press the ENTER

button.

ENTER

Setting

q Auto Flag Detect Mode (AFDM)

ON: This function only works for sources containing DTS-ES or 6.1-channel surround identification signals.

When this function is used, sources that have been recorded in 6.1-channel surround or DTS-ES are

automatically played in the 6.1-channel surround mode using the surround back speaker(s). (Refer to

w for the method of playback of the surround back speaker in this case.)

OFF: Set this mode if you wish to play normal 5.1-channel sources or sources not containing the

identification signals described below in the 6.1-channel mode.

w Non-Flag Source SBch Output

MTRX ON: Sources are played using the surround back speaker(s). The surround back channel is played

with digital matrix processing.

NON-MTRX: Sources are played using the surround back speaker(s). The same signals as those of the

surround channel are output from the surround back speaker(s).

OFF: Sources are played without using the surround back speaker(s).

2

Select the desired setting.

We recommend setting this to “OFF”.

When set to “ON”, then set the operation

for software for which no identification

signals are recorded (Non-Flag Source).

NOTES:

• The “SB CH Auto Flag Detect” setting screen is displayed when the surround back speaker(s) is/are set to

“Large” or “Small” at “Speaker Configuration”.

• The surround back speaker(s) can also be turned on and off using the “6.1/7.1 Surround” surround

parameter. (See page 26.)

3

Enter the setting.

The System Setup Menu reappears.

ENTER

12

ENGLISH

• Input the distance between the listening position and the different speakers to set the delay time for the

surround mode.

• The delay time can be set separately for surround speakers A and B.

Setting the delay time

Preparations:

Measure the distances between the listening position and the speakers

(L1 to L5 on the diagram at the right).

L1: Distance between center speaker and listening position

L2: Distance between front speakers and listening position

L3: Distance between surround speakers and listening position

L4: Distance between surround back speaker and listening position

L5: Distance between subwoofer and listening position

L1

L2

L5

L3

L4

Center FRFL

Subwoofer

SL

Listening position

SR

SB

1

At the System Setup Menu select “Delay Time”.

2

Switch to the Delay Time screen.

ENTER

Example: When “Meters” is selected

3

Select the desired unit, meters or feet.

Select (darken) the desired units, “Meters” or “Feet”.

4

Once “Meters” or “Feet” is selected in Step 3,

the Delay Time screen appears automatically.

5

Select the speaker to be set.

Example: When the distance is set to

3.6 m for the center speaker

6

Set the distance between the

center speaker and listening

position.

The distance changes in units

of 0.1 meters (1 foot) each

time the button is pressed.

Select the value closest to the

measured distance.

If “Ye s” is selected for “Default”, the settings are

automatically reset to the default values.

Please note that the difference of distance for every speaker

should be 4.5 m (15 ft) or less. If you set an invalid distance,

a CAUTION notice, such as screen right will appear. In this

case, please relocate the blinking speaker(s) so that its

distance is no larger than the value shown in highlighted line.

7

Enter the setting.

The System Setup Menu reappears.

The AVR-2802 automatically sets the optimum surround delay time for the listening room.

ENTER

NOTE:

• If the distance unit is changed after the delay time is set, the settings are reset to the factory default values

(see page 9).

• Use this setting to adjust so that the playback level between the different channels is equal.

• From the listening position, listen to the test tones produced from the speakers to adjust the level.

• The level can also be adjusted directly from the remote control unit. (For details, see page 24.)

Setting the channel level

1

At the System Setup Menu select “Channel Level”.

2

Switch to the Channel Level screen.

ENTER

3

Select “Test Tone Mode”.

13

ENGLISH

Example: When the “Auto” mode is selected

4

Select the mode.

Select “Auto” or “Manual”.

• Auto:

Adjust the level while listening to the test tones produced

automatically from the different speakers.

• Manual:

Select the speaker from which you want to produce the

test tone to adjust the level.

5

Select “Test Tone Start”.

Use the CURSOR buttons to adjust all the speakers to the same volume.

The volume can be adjusted between –12 dB and +12 dB in units of 1 dB.

When the surround back speaker setting is set to “2spkrs” for “Speaker

Configuration”, this is set to “SBR”, “SBL”.

Example: When the volume is set to

–12 dB while the test tone

is being produced from the

subwoofer

FL C FR SR

SBR SBL

SL SW

SB

6

Select “Ye s”.

7

a. If the “Auto” mode is selected:

Test tones are automatically emitted from the different

speakers.

The test tones are emitted from the different speakers in

the following order, at 4-second intervals the first time and

second time around, 2-second intervals the third time

around and on:

Flashing

Example: When the volume is set to

–12 dB while the

subwoofer is selected

b. When the “Manual” mode is selected

Use the and cursor buttons to select the speaker

for which you want to output test tones, then use the

and cursor buttons to adjust so that the volume of

the test tones from the various speakers is the same.

Flashing

8

After the above settings are completed, press the ENTER button.

The “Channel Level” screen reappears.

Press the ENTER button again, the “System Setup Menu” screen reappears.

ENTER

To cancel the settings, select “Level Clear” and “Yes ” on the “Channel Level” screen, then make the

settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter

at the listening position.

If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because

adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural

balance.

NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s

own volume control.

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel

level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level

adjustment mode.

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the

individual surround modes and adjust channel levels that will be remembered for each of those modes.

Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments

for just that mode will be recalled. Check the instructions for adjusting channel levels within each

surround mode on page 24.

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/6 CH

STEREO, DOLBY/DTS SURROUND, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and

MATRIX.

• This setting assigns the digital input jacks of the AVR-2802 for the different input sources.

Setting the Digital In Assignment

1

At the System Setup Menu select “Digital In Assignment”.

2

Switch to the Digital In Assignment screen.

ENTER

3

Select the digital input jack to be assigned to the input source.

• To select the input source

• To select the digital input jack

Select “OFF” for input sources for which no digital input jacks are used.

If “Ye s” is selected for “Default”, the settings are automatically reset

to the default values.

4

Enter the setting.

The System Setup Menu reappears.

ENTER

NOTES:

• The OPTICAL 3 jacks on the AVR-2802’s rear panel are equipped with an optical digital output jack for

recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording

between a digital audio source (stereo - 2 channel) and a digital audio recorder.

• Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-2802’s rear

panel to any jack other than the OPTICAL 3 IN jack.

•“PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.

14

ENGLISH

• Use this to turn the on-screen display (messages other than the menu screens) on or off.

Setting the on-screen display (OSD)

1

At the System Setup Menu select “On Screen Display”.

2

Switch to the On Screen Display screen.

ENTER

3

Select “ON” or “OFF”.

4

Enter the setting.

The System Setup Menu reappears.

ENTER

Use this to automatically search for FM broadcasts and store up to 40 stations at preset channels A1 to 8, B1 to

8, C1 to 8, D1 to 8 and E1 to 8.

NOTE:

• If an FM station cannot be preset automatically due to poor reception, use the “Manual tuning” operation to

tune in the station, then preset it using the manual “Preset memory” operation.

Auto tuner preset

1

Use the CURSOR buttons to specify “Auto Tuner Presets”

from the “System Setup Menu” screen.

2

Press the ENTER button.

The “Auto Preset Memory” screen appears.

ENTER

3

Use the CURSOR button to select “Yes”.

“Search” flashes on the screen and searching begins.

“Completed” appears once searching is completed.

The display automatically switches to screen.

This completes system setup. Once these settings are made, there is no need to change them unless

different AV components are connected or the speakers are repositioned.

This button can be pressed at any time during the system setup process to complete the process.

After completing system setup

1

At the System Setup Menu, press the SYSTEM SETUP button.

The changed settings are entered and the on-screen display turns off.

TITLE

SYSTEM

SETUP

• On-screen display signals

1

2

3

4

Signals input to the AVR-2802 On-screen display signal output

VIDEO signal input

jack (yellow)

S-video signal

input jack

VIDEO MONITOR OUT video

signal output jack (yellow)

S-video MONITOR OUT video

signal output jack

E

C

E

C

E

C

E

C

(

C

:

Signal

E

:

No signal)(

C

: On-screen signals output

E

:

On-screen signals not output)

NOTES:

• The on-screen display signals are not output from the color difference (component) video signal

MONITOR OUT jacks.

• For 4 above, the on-screen display signals are output to the VIDEO MONITOR OUT video signal output

jack (yellow) if the monitor TV is not connected to the S-video MONITOR OUT video signal output jack.

15

ENGLISH

B

• Point the remote control unit at the remote sensor on the

main unit as shown on the diagram.

• The remote control unit can be used from a straight

distance of approximately 7 meters from the main unit,

but this distance will be shorter if there are obstacles in

the way or if the remote control unit is not pointed directly

at the remote sensor.

• The remote control unit can be operated at a horizontal

angle of up to 30 degrees with respect to the remote

sensor.

NOTES:

• It may be difficult to operate the remote control unit if the

remote sensor is exposed to direct sunlight or strong

artificial light.

• Do not press buttons on the main unit and remote control

unit simultaneously. Doing so may result in malfunction.

• Neon signs or other devices emitting pulse-type noise

nearby may result in malfunction, so keep the set as far

away from such devices as possible.

Approx. 7 m

30°

Using the remote control unit

8

REMOTE CONTROL UNIT

• The included remote control unit (RC-904) can be used to operate not only the AVR-2802 but other remote

control compatible DENON components as well. In addition, the memory contains the control signals for

other remote control units, so it can be used to operate non-Denon remote control compatible products.

Inserting the batteries

q Remove the remote control unit’s rear

cover.

w Set three R6P/AA batteries in the battery

compartment in the indicated direction.

e Put the rear cover back on.

Notes on Batteries

• Use R6P/AA batteries in the remote control unit.

• The batteries should be replaced with new ones

approximately once a year, though this depends on the

frequency of usage.

• Even if less than a year has passed, replace the batteries

with new ones if the set does not operate even when the

remote control unit is operated nearby the set. (The

included battery is only for verifying operation. Replace it

with a new battery as soon as possible.)

• When inserting the batteries, be sure to do so in the

proper direction, following the “≈” and “√” marks in the

battery compartment.

• To prevent damage or leakage of battery fluid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

• Remove the batteries from the remote control unit when

you do not plan to use it for an extended period of time.

• If the battery fluid should leak, carefully wipe the fluid off

the inside of the battery compartment and insert new

batteries.

• When replacing the batteries, have the new batteries

ready and insert them as quickly as possible.

• The learned remote control signals may be cleared if no

batteries are in the remote control unit for about 5

seconds.

The factory-installed codes are in permanent memory,

however.

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

3

2

1

3

CDR

/

TAPE

Operating DENON audio components

1

Set mode switch 1 to “AUDIO (AVR/AVC)”.

2

Set mode switch 2 to the position for the

component to be operated.

• Turn on the power of the different components before operating them.

AVR/AVC VIDEO

AUDIO

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

3

Operate the audio component.

• For details, refer to the component’s operating instructions.

While this remote control is compatible with a wide range of infrared controlled components, some

models of components may not be operated with this remote control.

1. CD player (CD) and CD recorder and

MD recorder (CDR/MD) system buttons

2. Tape deck (TAPE) system buttons

VOLUME DISC SKIP+

VCR-2/V.AUX

TV/VCR

A / B

+10

VOLUME DISC SKIP+

VCR-2/V.AUX

TV/VCR

A / B

+10

6, 7 : Manual search (forward and reverse)

2 :Stop

1 : Play

8, 9 : Auto search (cue)

3 : Pause

DISC : Switch disc

SKIP + (for CD changers only)

6 : Rewind

7 : Fast-forward

2 :Stop

1 : Forward play

3 : Pause

8 : Reverse play

A/B : Switch between decks A and B

3. Tuner system buttons

DVD

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

123

4

SET CALL OFF

ON

/

SOURCE

56

789

CDR

/

TAPE

SHIFT : Switch preset channel range

CHANNEL : Preset channel up/down

+, –

*

For the tuner only, the following buttons can also be

operated:

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

RETURN

STATUS

DISPLAY

ON SCREEN

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

ENTER

TUNING •, ª : Tuning up/down

BAND : Switch between AM and FM bands

MODE : Switch between auto and mono

MEMORY : Preset memory

SHIFT : Switch preset channel range

RDS : RDS search

PTY : PTY search

RT : Radio text

Preset codes set upon shipment from the factory.

16

ENGLISH

• DENON components can be operated by setting the preset memory for CDR or MD. Operation is not

possible for some models, however. In this case use the learning function (see page 18) to store the

remote control signals.

• For instructions on clearing the presettings stored in the preset memory, see page 19.

Preset memory (Audio component)

1

Set the slide switch to “AUDIO”.

AVR/AVC VIDEO

AUDIO

2

Set the slide switch to “CDR/MD”.

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

3

2

1

CDR

/

TAPE

3

Holding in the POWER button, press the button for the

components you want to set.

The LEARNED/TX LED flashes.

• DENON and other makes of components can be operated by setting the preset memory for your make of

video component. Operation is not possible for some models, however. In this case use the learning

function (see page 18) to store the remote control signals.

• For instructions on clearing the presettings stored in the preset memory, see page 19.

Preset memory (Video component)

1

Set the slide switch to “VIDEO”.

AVR/AVC VIDEO

AUDIO

2

Set the slide switch to the component to be

registered (DVD, VDP, VCR or TV). .

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

3

3,4

4

2

1

CDR

/

TAPE

4

Next, while holding the POWER button, press the button for

the code in block B. (Refer to Table 1.) The operation is

completed when the button is released and the LEARNED/TX

LED lights.

“CDR/MD”

(DIRECT) (STEREO) (EXT. IN)

DIRECT

STEREO

EXT.IN

DENON CDR A DENON CDR B DENON MD(POWER)

ON

/

SOURCE

Combinations of Personal System Codes

Keep the POWER button pressed in when

performing steps 3 and 4

()

3

Holding in the POWER button, press the button for the

corresponding manufacturer in block A. (Refer to Table 1.)

The LEARNED/TX LED flashes.

Flashes

5

To continue registering other components, repeat steps 2 to 4.

• This remote control unit can be used to operate components of

other manufacturers without using the learning function by

registering the manufacturer of the component as shown on Table 1.

17

ENGLISH

“DVD”

Table 1: Combinations of Personal System Codes for Different Manufacturers

“VDP”

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

(VCR/V. AUX)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

A / B

CHANNEL

–

CHANNEL

+

SHIFT

DENON A

—

PANASONIC

—

SONY

PIONEER

TOSHIBA

—

DENON B

—

DIRECT

STEREO

EXT.IN

(DIRECT) (STEREO) (EXT. IN)A

B

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

(VCR/V. AUX)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

A / B

CHANNEL

–

CHANNEL

+

SHIFT

DENON A

—

MITSUBISHI

PANASONIC

—

SONY A

PIONEER

TOSHIBA

—

PHILIPS

RCA

—

MAGNAVOX

DENON B

—

SONY B

—

DENON C

—

SONY C

—

DIRECT

STEREO

EXT.IN

(DIRECT) (STEREO) (EXT. IN)A

B

“VCR”“TV”

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

(VCR/V. AUX)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

A / B

CHANNEL

–

CHANNEL

+

SHIFT

—

HITACHI A

MITSUBISHI A

PANASONIC A

JVC (VICTOR) A

SONY A

PIONEER

TOSHIBA A

SANYO A

SHARP A

NEC A

PHILIPS A

RCA A

MAGNAVOX A

—

HITACHI B

MITSUBISHI B

PANASONIC B

JVC (VICTOR) B

SONY B

—

TOSHIBA B

SANYO B

SHARP B

NEC B

PHILIPS B

RCA B

MAGNAVOX B

—

MITSUBISHI C

PANASONIC C

JVC (VICTOR) C

SONY C

—

NEC C

PHILIPS C

—

MAGNAVOX C

DIRECT

STEREO

EXT.IN

(DIRECT) (STEREO) (EXT. IN)A

B

q (DVD)

w (VDP)

e (TUNER)

r (TV/DBS)

t

y (PHONO)

u (VCR-1)

i (CD)

o (CDR/TAPE)

(VCR/V. AUX)

p

(SHIFT)

(CHANNEL +)

(CHANNEL –)

(A/B)

A / B

CHANNEL

–

CHANNEL

+

SHIFT

—

DENON/HITACHI

MITSUBISHI A

PANASONIC A

JVC (VICTOR)

SONY

PIONEER

TOSHIBA

SANYO

SHARP

NEC

PHILIPS A

RCA

MAGNAVOX

—

MITSUBISHI B

PANASONIC B

—

DIRECT

STEREO

EXT.IN

(DIRECT) (STEREO) (EXT. IN)A

B

GENERAL

ELECTRIC A

GENERAL

ELECTRIC B

GENERAL

ELECTRIC A

GENERAL

ELECTRIC B

Preset codes set upon shipment from the factory.

NOTES:

• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental

operation, cover the remote control unit’s transmitting window while setting the preset memory.

• Some models and years of manufacture of components of the manufacturers listed on Table 1 cannot be

used.

• The signals stored at “learned” buttons have priority over the preset codes. If you wish to clear the

“learned” signals, do so as described on page 19.

• Some manufacturers use different types of remote control codes for their products. If the component does

not operate when set to remote codeset A, try setting to the B or C codesets.

Operating a video component stored in the preset memory

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

CDR/TAPE

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

3

2

3

1

3

1

Set the slide switch to “VIDEO”.

AVR/AVC VIDEO

AUDIO

2

Set the slide switch to the component to be

registered (DVD, VDP, VCR or TV).

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

3

Operate the video component.

• For details, refer to the component’s operating instructions.

Some models cannot be operated with this remote control

unit.

DVD

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

CDR

/

TAPE

1. DVD player system buttons

POWER : Turns power on and off

(ON/SOURCE)

6,7 : Manual search (forward and reverse)

2 :Stop

1 : Play

8,9 : Auto search (cue)

3 : Pause

SKIP + : (for DVD changers only)

TITLE : Call out title

MENU : Call out menu

DISPLAY : Switch display

DVD SET UP

: DVD setup

RETURN : Menu return

•,ª : Cursor up/down

0,1 : Cursor left/right

SELECT : Enter setting

NOTE:

Some manufacturers use different names for the DVD remote control

buttons, so also refer to the instructions on remote control for that

component.

2. Video disc player (VDP)

system buttons

3. Video deck (VCR) system

buttons

4. Monitor TV system buttons

POWER : Power on/off

(ON/SOURCE)

6,7 : Manual search

(forward and reverse)

2 :Stop

1 : Play

8,9 : Auto search (cue)

3 : Pause

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123

4

SET

A / B

CALL OFF

ON

/

SOURCE

56

789

+10

0

CDR

/

TAPE

POWER : Power on/off

(ON/SOURCE)

6,7 : Manual search

(forward and reverse)

2 :Stop

1 : Play

3 : Pause

CHANNEL : Switch channel

+, –

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123

4

SET

A / B

CALL OFF

ON

/

SOURCE

56

789

+10

0

CDR

/

TAPE

POWER : Power on/off

(ON/SOURCE)

VOLUME : Volume

•,ª up/down

TV/VCR : Switch between TV

and VCR

CHANNEL : Switch channel

+, –

DVD

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

123

4

SET

A / B

CALL OFF

ON

/

SOURCE

56

789

+10

0

CDR

/

TAPE

18

ENGLISH

• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets,

you can “teach” the AVR-2802’s remote control to “learn” the codes from the component’s original remote

control.

• The buttons that can be “learned” are the CD, TAPE and CDR/MD system

buttons (see page 15) and the DVD, VDP, VCR and TV system buttons (see

page 17). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can

also be “learned”, and for the DVD and TV, the B block buttons can also be

“learned”.)

Learning function

1

Press the USE/LEARN selector button with the

tip of a pen etc., to set the learn mode. Both

the START and LEARNED/TX indicators flash.

2

Set the program switch to the side to be

learned.

Set to the AUDIO side for the CD, tape deck or

CDR/MD position, to the VIDEO side for the

DVD, VDP, VCR or TV position.

AVR/AVC VIDEO

AUDIO

3

Set the program switch to the position to be

learned.

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

A

2

4

3

B

1,8

CDR

/

TAPE

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

4

Set the remote control units so they are facing

each other, then press the button to be learned

on this unit’s remote control unit.

5

Check that the START LED is lit, then press the

button to be “learned” on the other remote

control unit.

6

Once the START LED turns off and the

LEARNED/TX LED lights, release the button on

the other remote

control unit.

7

To “learn” other buttons, repeat steps 2 to 6.

8

Once the learning operation is completed,

press the USE/LEARN selector button again.

The two LEDs stop flashing and the learning

mode is cancelled.

This unit’s remote

control unit

Flashes

The indicator stops flashing and the START LED

lights.

The learnable buttons are the buttons which can

be operated with the DENON system codes for

the CD player, tape deck, CD recorder, MD

recorder, the buttons which can be operated

with the preset memory for the DVD, VCR, VDP

and TV. For the TV only, however, the buttons in

the section indicated “A” on the diagram above

can also be “learned”. Use these to “learn” TV

channels.

This unit’s remote

control unit

Transmitting windows

Other remote

control unit

Approx.

5 cm

Light

This unit’s remote

control unit

Other remote

control unit

The two LEDs start

flashing again.

Light

Check that the stored

codes work properly.

NOTES:

• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once

again light when the button(s) is released.

• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For

limited number of models, codes cannot be stored in RC-904.

• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full,

and the code you have just attempted to store was not stored.

To “learn” that code, first perform the resetting operation. (See page 19.)

• The included remote control unit is equipped with a system call function for transmitting multiple remote

control signals when a single button is pressed (this is often referred to as a “macro” function).

This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s

power, turn on a source component’s power and start playback, etc., all at the touch of a button.

(1) System call buttons

The buttons that can be used for the system call function are shown on the table below.

A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up

to 5 operations can be performed with other buttons.

System call signals are already preset at the buttons indicated in the shaded section. System call signals can

also be stored at any button on the remote control unit, including the buttons in this section. (See page 19.)

System call function

Button

No.

transmissions

Stored

operation 1

The system call signals for the POWER

OFF and POWER ON buttons are

transmitted from the remote control unit

approximately once every second.

The signals for the other buttons (DVD,

VDP, TV / DBS, VCR-1 and CD) are

transmitted approximately once every

1.5 seconds.

Stored

operation 2

Stored

operation 3

Stored

operation 4

Stored

operation 5

Stored

operation 6

Stored

operation 7

Stored

operation 8

Stored

operation 9

Stored

operation 10

POWER OFF 10

POWER ON 10

DVD 5

Receiver

power on

DVD player

(DVD)

power on

Receiver

input source

switched to

DVD

TV power on

DVD player

(DVD)

playback

VDP 5

Receiver

power on

LD player

(VDP)

power on

Receiver

input source

switched to

VDP

TV power on

LD player

(VDP)

playback

TV/DBS 5

Receiver

power on

TV power on

Receiver

input source

switched to

TV/DBS

VCR-1 5

Receiver

power on

Video (VCR)

power on

Receiver

input source

switched to

VCR-1

TV power on

Video (VCR)

playback

CD 5

Receiver

power on

Receiver

input source

switched to

CD

(2) Using the system call function

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

2

1

CDR

/

TAPE

1

Press the system call button.

• The LEARNED/TX LED flashes for 5

seconds.

CALL

2

Press the button at which the desired system call signals are

stored while the LEARNED/TX LED is flashing.

• The preset signals or the signals you have stored at that

button are transmitted in succession.

19

ENGLISH

(3) Storing signals

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

1,5

2

3

CDR

/

TAPE

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

1,3

2

CDR

/

TAPE

(4) Clearing system call settings

1

Press the SET button.

• The START LED and LEARNED/TX LED both

flash.

AVR/AVC VIDEO

AUDIO

2

Press the button at which you want to store the

system call signals.

• The START LED flashes.

3

Set the mode switch to the position for the

component whose remote control signals you

want to store.

SET

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

4

Press the buttons whose remote control

signals you want to store one by one.

5

Press the SET button.

SET

1

Press the SET button.

SET

2

Press the button whose settings you want to

clear.

3

Press the SET button.

• The button is reset to the settings shown on

the table on page 18.

SET

NOTES:

• The remote control signals for the buttons pressed while storing the system call signals are transmitted

when the buttons are pressed, so cover the remote sensor or take other measures so that the components

do not operate while the signals are being stored.

• The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have

pressed or if you have already stored the maximum number of signals.

Clearing “learned” remote control signals

1

Press the USE/LEARN selector button with the

tip of a pen, etc., to set the learn mode.

2

To clear “learned” remote control signals, set

the slide switch to the position at which the

signals were “learned”.

AVR/AVC VIDEO

AUDIO

3

Set the slide switch to the position at which the

signals were “learned”.

DVD TV

VDP VCR

CD

MULTI

CDR/MDTAPE

4

Press the SYSTEM CALL SET button, and hold

it in for at least four seconds.

• When both the START and LEARNED/TX

LEDs light simultaneously, all the stored

codes are cleared.

Light

SET

5

Press the USE/LEARN selector button.

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI DVD

SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

4

2

1,5

3

CDR

/

TAPE

20

ENGLISH

9

OPERATION

34

VOLUME LEVEL

AUTO

LOCK

STAND BY

DIGITAL

PCM

SIGNAL

DIGITAL

INPUT

REMOTE

SENSOR

B

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

USE/LEARN T.TONE MULTI SET UP

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

2

4

3

CDR

/

TAPE

Before operating

1

Refer to “CONNECTIONS” (pages 4 to 8) and

check that all connections are correct.

2

Set the remote control unit’s slide switch to the

AUDIO position. (only when operating with the

remote control unit)

ON / STANDBY

OFF

£

¢

ON

/

SOURCE

ON/STANDBY

Lights

(Main unit) (Remote control unit)

• ¢ ON/STANDBY

The power turns on and “ON/STANDBY”

indicator is light.

Several seconds are required from the time

the power operation switch is set to the “¢

ON/STANDBY” position until sound is output.

This is due to the built-in muting circuit that

prevents noise when the power switch is

turned on and off.

Set the power operation switch to this

position to turn the power on and off from the

included remote control unit (RC-904).

• £ OFF

The power turns off and “ON/STANDBY”

indicator is off.

In this position, the power cannot be turned

on and off from the remote control unit (RC-

904).

3

Turn on the power.

Press the POWER operation switch (button).

AVR/AVC VIDEO

AUDIO

4

Select the front speakers.

Press SPEAKER A or B turn the speaker on.

SPEAKER

(Main unit) (Remote control unit)

1135

2

3

VOLUME LEVEL

AUTO

LOCK

STAND BY

DIGITAL

PCM

SIGNAL

DIGITAL

INPUT

REMOTE

SENSOR

B

Playing the input source

DVD

START LEARNED/TX

SPEAKER

TUNING

BAND

TITLE

MENU/GUIDE

MODE

MEMORY

RDS

PTY

RT

RETURN

STATUS

DISPLAY

ON SCREEN

DOLBY / DTS

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

INPUT MODE

ANALOG EXT.IN

MUTING

MASTER VOL.

VOLUME DISC SKIP+

SYSTEM CALL POWER

VDP TUNER SHIFT

TV/DBS PHONO

VCR-1 CD

CDR

/

TAPE

CHANNEL

VCR-2/V.AUX

TV/VCR

AVR/AVC VIDEO DVD TV

AUDIO

VDP VCR

CD

MULTI

CDR/MDTAPE

SYSTEM

SETUP

SURROUND

PARAMETER

CH SELECT

SELECT

RC-904

123

4

SET

A / B

CALL OFF

ENTER

ON

/

SOURCE

56

789

+10

0

1

3

2

5

1

Select the input source to be played.

Example: CD

To select the input source

when REC MULTI OUT or

TUNING PRESET is selected,

press the SOURCE button

then operate the input function

selector.

SOURCE

FUNCTION

CD

8

(Main unit) (Remote control unit)

AUTO PCM DTS

• Selecting the external input (EXT. IN) mode

Press the EXT. IN to switch the external input.

EXT.IN

(Main unit) (Remote control unit)

• Selecting the AUTO, PCM and DTS modes

The mode switches as shown below each

time the INPUT MODE button is pressed.

Input mode selection function

Different input modes can be selected for the different

input sources. The selected input modes for the separate

input sources are stored in the memory.

q AUTO (auto mode)

In this mode, the types of signals being input to the

digital and analog input jacks for the selected input

source are detected and the program in the AVR-

2802’s surround decoder is selected automatically

upon playback. This mode can be selected for all input

sources other than PHONO and TUNER.

The presence or absence of digital signals is detected,

the signals input to the digital input jacks are identified

and decoding and playback are performed

automatically in DTS, Dolby Digital or PCM (2 channel

stereo) format. If no digital signal is being input, the

analog input jacks are selected.

Use this mode to play Dolby Digital signals.

w PCM (exclusive PCM signal playback mode)

Decoding and playback are only performed when PCM

signals are being input.

Note that noise may be generated when using this

mode to play signals other than PCM signals.

e DTS (exclusive DTS signal playback mode)

Decoding and playback are only performed when DTS

signals are being input.

r ANALOG (exclusive analog audio signal playback

mode)

The signals input to the analog input jacks are decoded

and played.

t EXT. IN (external decoder input jack selection mode)

The signals being input to the external decoder input

jacks are played without passing through the surround

circuitry.

NOTE:

• Note that noise will be output when CDs or LDs

recorded in DTS format are played in the “PCM”

(exclusive PCM signal playback) or “ANALOG”

(exclusive PCM signal playback) mode. Select the

AUTO or DTS mode when playing signals recorded in

DTS from a laser disc player or CD player.

Note on playing a source encoded with DTS

• Noise may be generated at the beginning of

playback and while searching during DTS

playback in the AUTO mode. If so, play in the

DTS mode.

(Main unit)

2

Select the input mode.

• Selecting the analog mode

Press the ANALOG button to switch to the

analog input.

ANALOG

(Main unit) (Remote control unit)

INPUT MODE

(Main unit) (Remote control unit)

La pagina sta caricando ...

Denon AVR-2802 Operating Instructions Manual

Denon AVR-2802 Operating Instructions Manual

in altre lingue

Documenti correlati

Altri documenti