DTS Nick Wash 600 Manuale utente

Marca
DTS
Modello
Nick Wash 600
Categoria
Proiettori
Tipo
Manuale utente

Questo manuale è adatto anche per

Made in ItalyMade in Italy
D.T.S. Illuminazione srl
Via Fagnano Selve 10/12/14
47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 [email protected] http://www.dts-lighting.it
GBGB
User’s Manual Rel 1.2User’s Manual Rel 1.2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
ARC 1200
NICK WASH 600
2
ARC 1200
3
NICK WASH 600
INDEX
1- SYMBOLS 4
2- GENERAL WARNING 4
3- GENERAL WARRANTY CONDITION 4
4- TECHNICAL FEATURES 5
5- TECHNICAL SPECIFICATIONS 5
6- ACCESSORIES 7
7- IMPORTANT SAFETY INFORMATION 8
7.1 Fire prevention
7.2 Prevention of electric shock
7.3 Safety
7.4 Level of protection against the penetration of solid and liquid objects
8- VOLTAGE AND FREQUENCY 9
9- INSTALLATION 9
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION 10
10.1 Protection
11- DMX SIGNAL CONNECTION 11
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING 12
13- DISPLAY FUNCTIONS 13
14- PERIODIC CLEANING 22
15- PERIODIC CONTROLS 22
16- DMX PROTOCOL 23
ARC 1200
1- SYMBOLS
Graphic symbols used on this manual
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information
regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced
person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON
INFLAMMABLE SURFACES”
0,5M
THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO
BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
4
F
!
NICK WASH 600
ARC 1200
5
NICK WASH 600
4- TECHNICAL FEATURES
The FAR features also a Free Axis Rotation (“FAR”) system.
The FAR allows limitless pan and tilt rotation: the NICK head rotates freely on its axes, horizontally or
vertically, without interruption, in either direction, never having to reverse motion.
NICK WASH 600
03.LDR005.T
03.LDR005.TF
03.LDR005.TWS
5- TECHNICAL SPECIFICATIONS
Overview
NICK WASH 600 is a self-contained compact high-output LED moving head projector with 13,5° - 40°
motorized zoom.
NICK WASH 600 is one of the brightest compact LED projectors on the market: luminosity at 5 m is no
less than 3.100 Lux (13,5°).
Applications
NICK WASH 600 is ideal in various applications, such as: lighting shopping malls, libraries, museums,
exhibitions, clubs, restaurants, buildings, monuments, as well as special events, fashion displays, etc.
The unit is easily installable even in the most refined settings, thanks to its attractive appearance.
LED technology
NICK WASH 600 light source is composed of 120 LEDs (30 Red,30 Green, 30 Blue, 30 White) with 9.750
total lumens.
The LEDs even distribution pattern featuring the same quantity of red, green, blue and white LEDs
guarantees high colour mixing quality and a uniform projection on surfaces, no matter what colour
is used.
NICK WASH 600 offers 2 different colour mixing modes (RGBW / CMY) and can generate 16 million
colours; colour temperature can be varied over a linear range from 2800°K to 6500°K.
Also, users can memorize a personalized white either from the menu or via DMX. The white is recalled
with the dedicated DMX “White” channel.
NICK WASH 600 is also available with 90 White +30 Amber LEDs, or in an RGBA version (on request).
Zoom . Pan/Tilt . Full-range power supply
NICK WASH 600 features a motorized linear Zoom (13,5°- 40°) with a high efficiency optics system;
zoom movement is smooth and uniform.
NICK WASH 600 features a motorized movement on horizontal (540° pan) and vertical (270° tilt) axes;
the unit can operate in vertical, horizontal or inverted positions, and can be positioned on the floor or
ground, or fitted to trusses; it is complete with a practical accessory for anchorage to the ground.
NICK WASH 600
NICK WASH 600 has a full-range AC 90-260 V, 50-60 Hz power supply, therefore ensures reliable
operation even in the case ofvoltage drops. Also, the unit can be used all over the world with no
specific adaptations, as the right voltage is always supplied.
Electr. Power Supply, Motorized Zoom, Black colour
Electr. Power Supply, Motorized Zoom, F.A.R. system, Black colour
Electr. Power Supply, Motorized Zoom, Wireless DMX ready, Black colour
LED technology
120 LEDs (30 Red, 30 Green, 30 Blue, 30 White); total luminous flux 9.750 Lumens
RGBW colour generation (16 million colours); 3 different colour mixing modes: RGBW, CMY, HSV
Colour temperature variable on a linear range (2.800°K÷6.500°K); no infrared / no ultraviolet emissions
LEDs average lifespan: 100.000 hours
Zoom
Motorized Zoom 13,5°- 40°
User interface
OLED colour display + 4 buttons
5- TECHNICAL SPECIFICATIONS
Free Axis Rotation (“FAR”) system;
Independent operation
Fully programmable via built-in user interface
Master or Slave capability (chains of up to 32 interconnected units)
Remote control
Remotely controlled by cable or wireless;
USITT DMX 512 serial digital protocol (reception / transmission)
DMX
17-20 DMX channels
Protection
IP20 protection rate
Movements (horizontal/pan – vertical/tilt axes)
Motorized movement 540° Pan (2.0 sec) / 270° Tilt (1.2 sec)
Power supply / consumption
Full range AC 90-260V, 50-60Hz
Power consumption:
* 90 V – 2,65 A – 240 W * 120 V – 2 A – 240 W * 230 V – 1 A – 240 W * 260 V – 0,9 A – 240 W
Thermal
Operating ambient temperature - 10° / + 40°
Finishes
Black or white finish
Certification and Safety
Certification CE;
LED Class
Class 2 LED product
Weight
7,9 Kg
ARC 1200
6
Dimensions
NICK WASH 600
Unit Dimensions (LxWxH)
360x217x440mm
Weight:
7,9 Kg
Packaging Dimensions (LxWxH)
430
Weight:
x 515 x 290 mm
10 Kg
6- ACCESSORIES
As standard
03.LDR005.T
03.LDR005.TF
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•1 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
03.LDR005.TWS
• 1 x INDOOR IP20 omnidirectional 2dBi antenna cod. 0508A033
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•1 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
Optional (on request)
03.LDR005.T)
Electr. Power Supply, Motorized Zoom, Black colour
Electr. Power Supply, Motorized Zoom, F.A.R. system, Black colour
Nick Wash 600 Electr. Power Supply, Motorized Zoom, Wireless
DMX ready, Black colour
Flight cases
• Professional Flight case for 4 units; compartment for accessories, swivel wheels, cover with hinges
with-stay, dishes on cover for piling, 8 handles (2 eachside) (cod. 0521C046.1)
Wireless DMX receivers retrofits (for
• Wireless DMX Receiver Card with INDOOR IP20 omni. 2dBi antenna included (cod.03.LA.117)
Clamps / safety wires
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1/4 turn 1 couple (2 pieces) (Cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
ARC 1200
7
NICK WASH 600
7- IMPORTANT SAFETY INFORMATION
7.1 Fire prevention:
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 0,5 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
7.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head.
-The level of technology inherent in the NICK WASH 600 requires the assistance of specialised personnel
for all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
7.3 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C.
Never handle the unit until at least 10 minutes have elapsed since the
projector was turned off.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
7.4 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 20.
ARC 1200
0,5M
8
F
!
!
NICK WASH 600
8- VOLTAGE AND FREQUENCY
The NICK WASH 600 can operate at 90-260 VOLT 50 or 60 Hz.
9- INSTALLATION
NICK WASH 600 may be either floor or ceiling mounted.
For floor mounting installations, the NICK WASH 600 is supplied with four rubber mounting feet on the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the NICK WASH 600 is moving.
Two 1/4 turn Fast Locks connections placed in the base of the units allow to hang the NICK WASH 600
by using the Fast Lock ‘C’ clamps provided in the box.
.
9.1- Safety cable
We recommend the use of a safety chain/cord connected to the NICK WASH 600 and to the suspension
truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the
iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain/cord to the attachment point (A) located on the base of the fixture, as
shown in the picture below.
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
ARC 1200
9
!
NICK WASH 600
!
A
SAFETY CHAIN/CORD
ATTACHMENT POINT
9.3- Movement
Unlimited Pan rotation; unlimited Tilt rotation (NICK WASH 600 ZOOM F.A.R.)
Pan 540° (2,0 sec.), Tilt 270° (1,2 sec.) (NICK WASH 600 ZOOM)
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 0,5 MT.
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on the head
of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in
operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
10- MAINS CONNECTION
NICK WASH 600 operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 1,5 amps at 230V,
Or 3 amps at 90 V
Strict adherence to regulatory norms is strongly recommended.
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each
NICK WASH 600.
ARC 1200
10
0,5M
F
!
Mains
90-260V AC 50 / 60Hz
NICK WASH 600
Netzanschluss
90-260V AC 50 / 60Hz
03.LDR005.T
03.LDR005.TWS
!
WARNING
Do not place any object in the path
of the projector’s movement
540°
270°
Free Axis Rotation ("F.A.R.”)
No Free Axis Rotation ("F.A.R.”)
03.LDR005.TF
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR
5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable
ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
ARC 1200
11
5
3
4 2
1
1=GND
2=DATA-
3=DATA+
CONTROLLER
STANDARD
DMX 512
NICK WASH 600
11.1-DMX Addresses
11.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
NICK WASH 600 can be used in 2 different DMX modes: 17 DMX control channels (default for NO FAR
models) , 20 DMX control channels (default for FAR model).
Here below is described the DMX channels addressing for the controller when NICK WASH 600 is set to
17 and 20 DMX control channels :
17 channels mode (default for NO FAR models)
Projector 1 A001
Projector 2 A018 If you want to select the next projector, just add “17”
Projector 3 A035
….. A….
projector 6 A086
20 channels mode (default for FAR model)
Projector 1 A001
Projector 2 A021 If you want to select the next projector, just add “20”
Projector 3 A041
….. A….
projector 6 A101
Please refer to an authorised D.T.S. service centre.
D.T.S. Firmware upgrade utility program.
D.T.S. Firmware upgrade utility
12 FIRMWARE UPDATING
Warning:
This procedure require a base knolewge of computer applications and Windows
Hyperterminal program.
To update the software version of the NICK WASH 600 you will need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Driver for the D.T.S. RED BOX interface .
(The driver and the installation procedure are available in our web site www.dts-lighting.it)
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using program.
ARC 1200
12
!
NICK WASH 600
ARC 1200
13
DISPLAY FUNCTIONS
The NICK WASH 600 display panel shows all the available functions . Using these functions, it is
possible to change some of the parameters and add some functions. Changing the DTS setting
can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.
Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Display
Up-Down
Up-DownENTER
Display Position
ON THE GROUND (Default)
SUSPENDED
ENTER
Menu
DISPLAY POSITION / STAND BY
Display Position:
Reverses display's reading depending on the
mounting position
(On the ground or suspended).
Display Standby:
To turn off the display (after 5 seconds)
Or leave it always on.
Display Standby
OFF = Display Standby disabled
(Default)
ON = Display goes OFF after 5
seconds
ENTER
MENU ENTER DOWN
UP
AA
DISPLAY
MENU ENTER DOWN
UP
OFF
DISPLAY
POSITION
STANDBY
NICK WASH 600
Software version 1.19
2dBi IP20
omnid.Antenne
Netz Eingang
elektronisches Schaltnetzteil
90-260V AC, 50/60Hz
Sicherung 5AT
(5x20mm)
DMX Ausgang
DMX Eingang
DMX Ausgang
DMX Eingang
Netz Eingang
elektronisches Schaltnetzteil
90-260V AC, 50/60Hz
Sicherung 5AT
(5x20mm)
DMX Eingang
DMX Ausgang
MENU
ENTER
DOWN
UP
DISPLAY
ARC 1200
14
13- DISPLAY FUNCTIONS
DMX Set
Up-Down
Up-DownENTER
DMX mode
17 channels (Default for NO FAR
MODELS)
20 channels (Default for FAR model)
ENTER
Menu
DMX MODE / MACRO
DMX Mode
To select DMX mode : 17 ch (default for
NO FAR models) or 20 DMX channels
(default for FAR model).
Macro
Macro Function, enable channel
mapping macro rainbow effects
STD (default)
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
17 ch not FAR
DMX SET
DMX MODE
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
STD
DMX SET
MACRO
MACRO
Standard mode enabled (Default)
Extended mode enabled: Rainbow
effects on MACRO channel
LED
Up-Down
Up-DownENTER
RED Min default =0
RED Max default = 255
ENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
LED
RED MIN
RGBA MINIMUM VALUES
This menu allow to select the
minimum levels for Red, Green,
Blue and Amber/White
RGBA MAXIMUM VALUES
This menu allow to select the
maximum levels for Red, Green,
Blue and Amber/White
These settings have priority on
Master Dimmer (DMX channel 7)
SMOOTH VALUE
This menu allow to select the value
of the delay ( in millisecons) for
RGBA and Dimmer channels
reaction to DMX or Program
variation.
4 = 25 ms delay (Fast response)
20 = 250 ms delay (Slow response)
GAMMA CORRECTION
This menu allow to select between
Linear current output or Quadratic
current output for LEDs.
Default = Linear
OUTPUT FREQUENCY
This menu allow to adjust the PWM
frequency value (Hz) in order to
reduce flickering in the process of
your camera recordings
BOOST DRIVING
This menu allow to increase the
LED’s current from 350mA to 500
mA
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
LED
GREEN MIN
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
LED
BLUE MIN
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
LED
AMBER MIN
BLUE Min default =0
BLUE Max default = 255
GREEN Min default =0
GREEN Max default = 255
AMBER Min default =0
AMBER Max default = 255
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
4
LED
SMOOTH
SMOOTH
Range = Off - 20
Default = 4
NICK WASH 600
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
20 ch With FAR
DMX SET
DMX MODE
ARC 1200
13- DISPLAY FUNCTIONS
15
LED
Up-Down
Up-DownENTER
GAMMA CORRECTION
Linear = Linear courrent output
Quadratic = Linear light output
ENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
LINE
LED
GAMMA CORR.
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
610
LED
OUTPUT FREQ.
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
ON
LED
BOOST
OUTPUT FREQUENCY
Range = 610 Hz -10 KHz
Default = 610 Hz
BOOST
Whit BOOST active,the LED’s current
is set to 500mA (30% more gain).
Default = Enabled
GAMMA CORRECTION
This menu allow to select between
Linear current output or Quadratic
current output for LEDs
Default = Linear
OUTPUT FREQUENCY
This menu allow to adjust the PWM
frequency value (Hz) in order to
reduce flickering in the process of
your camera recordings
BOOST DRIVING
This menu allow to increase the
LED’s current from 350mA to 500
mA
AUTO
Up-Down
Up-DownENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
AUTO
NICK WASH 600
SURE?
Menu - NO
Enter - YES
ENTER
AUTOMATIC MODE
Automatic demo game without
DMX controller.
PERSONAL COLOURS
RGBA, Dimmer, Shutter, Pan, Tilt
and Zoom values selectable by
user.
FIXED COLOURS
Sixteen Colour Macros as on
“MACRO” channel.
Dimmer, Shutter, Pan, Tilt and
Zoom values selectable by user.
STEP 01/16
Chase with 16 steps previously
created in REC MODE
Speed time, Wait time, Dimmer,
Pan, Tilt and Zoom values
selectable by user.
RAINBOW
Rainbow colours effect.
Speed time, Dimmer, Shutter,
Pan, Tilt and Zoom values
selectable by user.
WHITE MACROS
Sixteen macros for White color
from 2800 to 6500 ° K.
Dimmer, Shutter, Pan, Tilt and
Zoom values selectable by user.
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
01/16
AUTO-PROGRAM
STEP
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
120
AUTO-PERS.COL.
RED
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0010
AUTO-RAINBOW
SPEE
13- DISPLAY FUNCTIONS
AUTOMATIC MODE
Automatic demo game without
DMX controller
AUTO
Up-Down
Up-DownENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
1
AUTO-WHITE
WHITE NO.
20 ch
DMX SET
DMX MODE
1
AUTO-FIXED COL.
COLOR
MENU ENTER DOWN
UP
MENU ENTER DOWN
UP
ARC 1200
16
NICK WASH 600
ENTER
SLAVE
Up-Down
Up-DownENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
128
SLAVE
PAN
ENTER
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
SLAVE
SURE?
Menu - NO
Enter - YES
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
128
SLAVE
TILT
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
SLAVE
ZOOM
SLAVE MODE SETTING
This menu allow to set the Nick
Wash 600 as slave unit.
DMX signal must be present from
MASTER unit (set in AUTO MODE)
in order to ran the units in SLAVE
mode.
By setting all the SLAVE units
connected to the MASTER, to
DMX address 1, them will be
sinchronized with the Master unit
following the chase selected on it,
but running their own Pan&Tilt
and Zoom position.
The SLAVE unit receive DMX signal
from the MASTER unit.
By setting all the SLAVE units
connected to the MASTER, to DMX
address 1, them will be sinchronized
with the Master unit following the
chase selected on it, but running
their own Pan&Tilt and Zoom
position.
By setting all the units connected to
the MASTER, to DMX address 1,
them will be sinchronized with the
Master unit following the chase
selected on it, including TIME, WAIT,
Pan&Tilt and Zoom position of the
MASTER unit.
FIXED COLOURS
Sixteen Colour Macros as on
“MACRO” channel.
Dimmer, Shutter, Pan, Tilt and
Zoom values selectable by user.
WHITE MACROS
Sixteen macros for White color
from 2800 to 6500 ° K.
Dimmer, Shutter, Pan, Tilt and
Zoom values selectable by user.
WIRELESS
Up-Down
Up-DownENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
WIRELESS
UNLINK
20 ch
DMX SET
DMX MODE
OFF
WIRELESS
SELECTION
MENU ENTER DOWN
UP
MENU ENTER DOWN
UP
ENTER
13- DISPLAY FUNCTIONS
ARC 1200
17
NICK WASH 600
WIRELESS DMX
Wieless DMX enabled / disabled.
By activating WDMX MODE, it will
be possible to control Nick Wash
600 via D.T.S. ANTENNA Wireless
DMX Transmitter (cod. 03.E1271).
WIRELESS DMX system is
already installed on Nick Wash
600 with code 03.LDR005.TWS
WIRELESS DMX system on
Nick Wsh 600 with code
03.LDR005.T and
03.LDR005.TF is available on
request.
20 ch
DMX SET
DMX MODE
ON
WIRELESS
SELECTION
MENU ENTER DOWN
UP
MENU ENTER DOWN
UP
WIRELESS DMX SYSTEM
DISABLED
WIRELESS DMX SYSTEM
ENABLED
ENTER
UNLINK = LOG OUT
ENTER
Logging on Nick Wash 600 (WIRELESS DMX must be enabled on the unit)
To log on the NICK WASH 600 in the WIRELESS system simply press and quickly release the function button on the transmitter .
The transmitter will start flashing rapidly red/green scanning for new free receivers / NICK WASH 600 units. When a NICK WASH 600
logs on to the transmitter the LINK green light on transmitter starts to flash rapidly.
After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data. The NICK WASH 600
now try to synchronize to the transmitter.
When synchronized to the transmitter, 2 different modes are possible:
1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the transmitter and solid
display is seen on NICK WASH 600.
2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on NICK WASH 600
To log off NICK WASH 600 from a transmitter simply select UNLINK function under WIRELESS DMX MENU and press ENTER.
When NICK WASH 600 is logged off the display is blinking, meaning its available for log in on a new transmitter.
Logging out a NICK WASH 600
Select UNLINK function under WIRELESS DMX MENU and press ENTER.
When Nick Wash 600 is logged off the display is blinking, meaning its available for log in on a new transmitter.
Logging out all NICK WASH 600 linked to a transmitter
Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on Nick Wash 600, it mean
that the units are logged out.
Transmitter, Status LED
Flashing red/green, no dmx connected.
Solid green, dmx signal detected and transmitted.
Fast flashing red/green, log in mode (every free Nick Wash 600 unit, not logged in to any other transmitter, will be logged on)
NICK WASH 600 Status
Display blinking, not logged on to a transmitter (free).
Solid display, logged on to a transmitter and receiving dmx data.
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
OFF
EMERGENCY
SELECTION
EMERGECY
Up-Down
Up-DownENTER
Menu
EMERGENCY
Disabled = Default
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
1
EMERGENCY
WHITE
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
255
EMERGENCY
DIMMER
EMERGENCY
Emergency operating mode.
By setting Emergency mode, it
will be possible to select one of
the 16 preprogrammed WHITE
cues that will then ran if DMX
signal is missing or not available.
Usefull for Emergency EXIT
ilumination on public areas.
Dimmer leveL, Pan&Tilt and
Zoom values selectable by user.
WHITE 1-16
Default = WHITE 1
DIMMER
Default = 255
ENTER
13- DISPLAY FUNCTIONS
ARC 1200
18
NICK WASH 600
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
128
EMERGENCY
PAN
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
128
EMERGENCY
TILT
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0
EMERGENCY
ZOOM
PAN
Default = 128
TILT
Default = 128
ZOOM
Default = 0
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
ON
EMERGENCY
SELECTION
EMERGENCY
Enabled
13- DISPLAY FUNCTIONS
ARC 1200
19
DEFAULT SET
Up-Down
Up-DownENTER
Menu
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
DEFAULT SET
SURE?
Menu - NO
Enter - YES
DEFAULT SETTINGS
To restore default settings
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
DEFAULT SET
ENTER
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
028.7
TEMPER. °C
TEMPER. °C
Up-Down
ENTER
Menu
TEMPERATURE
Unit temperature
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
13 Hr - 08 min
TIME
TIME
Up-Down
ENTER
Menu
LIFE TIME
This menu show the total UNIT life time
and the RGBA life time
UNIT
Up-Down
ENTER
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0 Hr - 08 min
TIME
RED
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0 Hr - 08 min
TIME
GREEN
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0 Hr - 08 min
TIME
BLUE
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
0 Hr - 08 min
TIME
AMBER
NICK WASH 600
ARC 1200
20
13- DISPLAY FUNCTIONS
SYSTEM
Up-Down
ENTER
Menu
PAN INVERTION / TILT INVERTION /
PAN-TILT SPEED / FAN MAX SPEED /
RESET BY DMX / MOTORS FIRMWARE
UPGRADE.
Up-Down
ENTER
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
NORM
SYTEM
PAN INVERSION
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
NORM
SYTEM
TILT INVERSION
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
4
SYTEM
PAN-TILT SPEED
MENU ENTER DOWN
UP
DMX SET
DMX MODE
MENU ENTER DOWN
UP
100%
SYTEM
FAN MAX SPEED
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
ENAB
SYTEM
RESET BY DMX
MENU ENTER DOWN
UP
20 ch
DMX SET
DMX MODE
MENU ENTER DOWN
UP
SYTEM
MOTORS
FW UPGRADE
PAN INVERSION
This menu allows to set the Pan
movement.
Normal or Reversed.
TILT INVERTION
This menu allows to set the Pan
movement.
Normal or Reversed.
PAN TILT SPEED
Pan Tilt Speed control (1-4)
PAN INVERTION
Default = NORM
TILT INVERTION
Default = NORM
PAN TILT SPEED CONTROL
Default = 4
FAN MAX SPEED
This menu’ allow to select the
internal fans speed.
FAN MAX SPEED
50% - 100%
Default = 100%
RESET BY DMX
Enable: Motors reset enabled via
DMX (Default).
Disabled: Motors reset disabled via
DMX.
Now: Instant motors reset.
MOTORS FIRMWARE UPGRADE
This menu’ allow to upgrade the
firmware for ZOOM and Pan&Tilt
circuit boards.
MOTORS FIRMWARE UPGRADE
Zoom and Pan&Tilt circuit boards
firmware upgrade.
NICK WASH 600
RESET BY DMX
This menu’ allow to enable / disable
the Motors reset control (Pan&Tilt
and Zoom) via DMX.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

DTS Nick Wash 600 Manuale utente

Marca
DTS
Modello
Nick Wash 600
Categoria
Proiettori
Tipo
Manuale utente
Questo manuale è adatto anche per
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti