DTS XR700 SPOT Manuale utente

GB

Made in Italy

XR700 SPOT

User’s Manual Rel 1.2

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

D.T.S

D.T.S.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S.

ARC 1200

XR700 SPOT

2

3

ARC 1200

XR700 SPOT

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 7

6- IMPORTANT SAFETY INFORMATION 8

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING THE LAMP 9

7.1 Lamp alignment

8- VOLTAGE AND FREQUENCY 10

9- INSTALLATION 10

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 11

10.1 Protection

11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 13

13- DISPLAY FUNCTIONS 14

14- PAN & TILT SPEED 17

15- FANS SPEED

16- ERROR MESSAGES 17

17- HIDDEN MENU 18

18- OPENING THE PROJECTOR HOUSING 19

19- REPLACING GOBOS

20- PERIODIC CLEANING 20

20.1 Lenses and reflectors

20.2 Fans and air passages

21- PERIODIC CONTROLS

22- DMX PROTOCOL 21

23- 8 MOTORS CONTROL CARD 36

24- 6 MOTORS CONTROL CARD 37

25- PAN & TILT CARD 38

26- CABLES RESEND CARD

27- DISPLAY CARD

28- LAMP ON-OFF CONTROL CARD

29- ROTATING GOBO WHEEL 39

30- FIXED GOBO WHEEL 40

31- COLOUR WHEEL 1 41

32- COLOUR WHEEL 2 42

ARC 1200

1- SYMBOLS

Graphic symbols used on this manual

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information

regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or experienced

person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON

INFLAMMABLE SURFACES”

2M

THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO

BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

4

F

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP

CAN CAUSE DAMAGE TO EYES AND SKIN”

!

UV

XR700 SPOT

ARC 1200

4- TECHNICAL FEATURES

The XR700 SPOT is a brand new moving head fitted with a 700W discharge lamp, which delivers a

massive 27.000 Lux at 5 m (10°).

The XR700 SPOT is fitted with a Philips MSR Gold 700/2 Fastfit lamp (50.000 Lumens) combined with a

dichroic parabolic reflector.

The XR700 SPOT is one of the most complete moving heads in the 700W range and is particularly

suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed

(clubs and other venues), requiring a light with extremely high luminous output and versatility of

functions.

The XR700 SPOT in fact features a very flexible colour generation, thanks to two colour wheels with 7

colours each, with linear selection for perfect 2-colour beams, and also 2 colour conversion filters

(3200°K and 5600°K).

The XR700 SPOT incorporates also motorized focussing, motorized iris, motorized linear zoom (10°-

30°), 3-facet rotating prism, 1 wash effect filter.

2 gobo wheels are available, featuring respectively: 7 rotating and 16 bit indexable gobos

(interchangeable); 8 fixed gobos (interchangeable).

The XR700 SPOT also includes a new Pan / Tilt locking system with recessed buttons and electronic

ballast.

The XR700 SPOT is the ideal moving head as well for all applications in which noiseless operation is

required, thanks to its silent internal ventilation system and silent pan/tilt operation.

XR 700 SPOT (Cod. 03.MS006.EB.L)

• Electronic ballast 90-260V 50/60 Hz • Black colour

Also available in white (RAL 9003) colour on demand.

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit

Automatic switching ON of lamp in case of accidental switching OFF.

Lamp ON/OFF via DMX; Reset via DMX.

Optical group

27.000 Lux at 5 m (10°)

Dichroic glass reflector

Focus

Motorized focus

Iris

Motorized iris (16 bit)

Zoom

Motorized zoom (10°- 30°)

5

XR700 SPOT

4- TECHNICAL FEATURES

Dimmer / shutter / strobo

Linear dimmer

Shutter

Strobe from 0,85 flash/sec to 6,75 flash/sec

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

2 Colour wheels (7 colours + open with linear selection)

3200°K and 5600°K colour conversion filters

Colour change with blackout sync; rainbow effect

Gobos

2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (8 gobos + open)

Extractable gobo holders for both wheels

Gobo change with synchronized blackout

Gobo scrolling; Gobo shake

Effects

Indexable prism rotating in both directions (3-facet)

Wash effect filter

Pan / Tilt

Pan 540° (3,9 sec.)

Tilt 270° (2,6 sec.)

16-bit resolution

2-Speed function (2 selectable pan/tilt speeds); extremely smooth and precise movements even at the

highest speeds

Pan / Tilt locking system with recessed buttons

Automatic Pan/Tilt repositioning in case of knocks

25 DMX channels (Default)

Internal operating system updatable via DMX

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

POWERCONN connector by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz)

Power consumption: 820 W

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection

Thermal

Operating ambient temperature: -10° / 40°

Weight

31,5 Kg (electronic ballast)

ARC 1200

6

XR700 SPOT

4- TECHNICAL FEATURES

Dimensions

5- ACCESSORIES

As standard

•1 x MSR Gold 700/2 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• User’s manual

Optional (on request)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Unit Dimensions (LxWxH)

525x500x810mm

Weight: 31,5 Kg

Packaging Dimensions (LxWxH)

610 x 540 x 720 mm

Weight: 37 Kg

ARC 1200

7

XR700 SPOT

408 mm

625 mm

500 mm

415 mm

18 0 mm

525 mm

270°

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

MSR Gold 700 Fastfit lamp

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1.5 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology inherent in the XR700 SPOT requires the assistance of specialised personnel for

all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid objects is IP 20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

• Raincover for XR base (top) (cod. 03.MA001)

• Raincover for XR base (bottom) (cod. 03.MA002)

XR700 SPOT uses a PHILIPS /2

ARC 1200

2M

8

F

!

UV

XR700 SPOT

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).

The lamp used on XR700 SPOT is made in quartz glass and should be handled with care. Always follow

the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue

provided in the lamp's packaging. The lamp socket is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.

WARNING: Never look directly at the lamp when it’s lit.

Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit. The lamp alignment is also essential to obtain the

maximum unifirmity and luminous performance by the projection.

3 adjusters X, Y and

Z (photo 5)

you will have an evenly projected light beam, with no shadows or

zones wich are brighter than others.

Philips MSR Gold 700/2 Fastfit

Power 700W

Luminous flux 50,000 lm

Colour temperature 7.500°K

Lampbase PGJX50

Rated life 750 hours

PGJX50

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface

no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto

the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the

until you achieve a uniform flat field.

When the lamp is correctly optimized,

ARC 1200

Photo 2Photo 1 Photo 4Photo 3

Photo 5

9

Lamp

Alignment

UV

XR700 SPOT

8- VOLTAGE AND FREQUENCY

The XR700 SPOT with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR700 SPOT may be either floor or ceiling mounted.

For floor mounting installations, the XR700 SPOT is supplied with four rubber mounting feet on the

base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to

move or shake whilst the XR700 SPOT is moving.

Four quarter turn fast locks placed on the base of the units, allows by using the two fast lock C clamps

provided in the box, to fix the unit in any position.

.

9.1- Safety cable

We recommend the use of a safety cable connected to the XR700 SPOT and to the suspension truss in

order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron

cable can bear the weight of the entire unit.

You may attach the safety cable to the two holes (A) located on the base of the fixture, as shown in the

picture below.

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

A

ARC 1200

!

240 mm

105 mm

10

XR700 SPOT

9.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any

obstructions in the path of the projector's movement.

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended

distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the

base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the

projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature

should NOT exceed 40°C.

10- MAINS CONNECTION

XR700 SPOT with electronic ballast operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 8 amps at 230V,

Or16 amps at 100-120 V

Strict adherence to regulatory norms is strongly recommended.

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR700 SPOT.

A good earth connection is essential for the correct operation of the projector.

540°

270°

ARC 1200

11

2M

F

Electronic ballast

90-260V 50 / 60Hz

Fuse Holder

(12A T 5x20 Fuse)

!

WARNING

Do not place any object in the path

of the projector’s movement

!

XR700 SPOT

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the

projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR

5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable

ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it

to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the

second one.

In this way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

ARC 1200

12

5

3

4

2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S T A N D A R D

D M X 5 1 2

XR700 SPOT

11.1-DMX Addresses

XR700 SPOT can be controlled with 18, 25 (default) or 26 DMX channels.

If you want to use the unit in 25 channels mode (default), set the following addresses on the mixer:

Projector 1 A001

Projector 2 A026 If you want to select the next projector, just add “25”

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will

start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a

faster selection.

Projector 3 A051

….. A….

projector 6 A126

12 FIRMWARE UPDATING

Warning:

This procedure require a base knolewge of computer applications and Windows

Hyperterminal program.

To update the software version of the XR700 SPOT you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface .

(The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updated software version.

Please follow the below procedure to perform the updating:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal program.

It will be possible to download the software from the reserved area of D.T.S. web site:

www.dts-lighting.it.

Please refer to an authorised DTS service centre.

ARC 1200

13

!

XR700 SPOT

13- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The XR700 SPOT display panel shows all the available functions . Using these functions, it is

possible to change some of the parameters and add some functions. Changing the DTS setting

can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.

Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Up-DownMENU ENTERUp-Down

PAN MOVEMENT INVERSION

To reverse Pan movement from left

to right and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTERUp-Down

TILT MOVEMENT INVERSION

To reverse Tilt movement from

bottom upwards and vice versa

Up-Down

Counterclockwise

Clockwise

Up-DownMENU ENTER

DMX MODE

To select DMX mode : 25 (default),

26 or18 DMX channels

25 CHANNELS

(Pan & Tilt 16 bit)

18 CHANNELS

(Pan & Tilt 16 bit)

Up-Down

ENTER

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position

(On the ground or suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

DISPLAY STAND BY

To turn off the display (after 5 seconds)

Or leave it always on.

Display OFF

Display

always ON

ENTER

DMX IN

DMX OUT

DISPLAY

MENU

ENTER

DOWN

UP

MAINS

Electronic ballast

90-260V 50 / 60Hz

FUSE

12 A T 5x20

ARC 1200

14

XR700 SPOT

DMX IN

DMX OUT

Default

Same fixture as XR9 SPOT

26 CHANNELS

(Pan & Tilt 16 bit)

MENU

ENTER

DEFAULT

To restore default setting

ENTER

Up-Down

MENU ENTER

Fan control

To control the fan speed .

Up-Down

ENTER

Up-Down

(DEFAULT : 5 )

MENU ENTER

Up-Down

ENTER

Up-Down

(DEFAULT : 2 )

SPEED control

Pan&Tilt Speed control.

13- DISPLAY FUNCTIONS

ENTER

MENU

Up-Down

ENTER

MENU

Up-Down

ENTER

Up-Down

GOBO ROTATION DURING GOBO SCROLLING

DISABLED (DEFAULT)

.

ENTER

SOFTWARE

Software version for 8 motors and Pan&Tilt circuit

Boards

MENU

Up-Down

RESET

Al motors reset

RESET ENABLED VIA DMX

RESET DISABLED VIA DMX

TOTAL RESET

ENTER

Up-Down

.

ARC 1200

XR700 SPOT

FACTORY SETTINGS

8 MOTORS CIRCUIT BOARD (4.1) AND

PAN&TILT CIRCUIT BOARD (2.7)

15

LAMP

Lamp always ON-always OFF

Or lamp ON-OFF selectable via DMX

ENTER

FORCED ON

ENTER

FORCED OFF

ENTER

ON / OFF VIA DMX (default)

MENU

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ADJUST

To adjust the lamp with no mixer connected.

It’s possible to set the parameters for

PAN, TILT, FOCUS and ZOOM

ENTER

STRIKE

Lamp strikes counter

ENTER

Up-Down

MENU

Up-Down

ENTER

AUTO FOCUS

Automatic focusing during Zoom adjustment

.

Up-Down

AUTOMATIC FOCUS DISABLE (DEFAULT)

AUTOMATIC FOCUS ENABLE

ENTER

GOBO1 Rotation

Gobo1 Rotation during gobo scrolling

GOBO ROTATION DURING GOBO SCROLLING

ENABLED

ENTER

MENU

Up-Down

ENTER

RESERVED

Pan lock-Tilt lock, Pan free-Tilt free and

System Reboot

Up

ENTER

.

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

.

ENTER

Up-Down

ENTER

Up-Down

.

ENTER

PAN LOCK

LOCK THE PAN TO THE DESIRED VALUE

TILT LOCK

LOCK THE TILT TO THE DESIRED VALUE

PAN FREE

REMOVE POWER TO PAN MOTOR

TILT FREE

REMOVE POWER TO TILT MOTOR

MENU ENTER

TIMER

lamp life TIME (reset possible)

and total UNIT LIFE TIME (reset not possible)

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

16

13- DISPLAY FUNCTIONS

ARC 1200

XR700 SPOT

ENTER

BOOT

SYSTEM REBOOT

LAMP LIFE TIME

UNIT LIFE TIME

LAMP LIFE TIME

COUNTER RESET

SILENT

Silent operating mode during PAN&TILT movement.

By activating this function, PAN and TILT motors will

be driven with less power (during aceleration and

deceleration) in order to reduce the noise during

PAN&TILT rotation

ENTER

SILENT MODE DISABLED

ENTER

SILENT MODE ENABLED (DEFAULT)

MENU

Up-Down

ENTER

Up-Down

14- PAN & TILT SPEED (SPEE) (default: 1)

15- FAN SPEED (FANS)( default: 5)

You can set the PAN and TILT motors at high speed on your XR700 SPOT.

Press menu until you see SPEE.

Press ENTER and select a speed with UP-DOWN (there are 2 speeds). Confirm by pressing ENTER.

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be

less than 35° C.

ARC 1200

XR700 SPOT

17

16- ERROR MESSAGES

ERROR: COLOR 2 WHEEL POSITION

ERROR: INTERNAL COMMUNICATION

ERROR: ENCODER PAN

ERROR: ENCODER TILT

ERROR: DMX ADDRESS

ERROR: LOAD DATA EEPROM

ERROR: EFFECTS POSITION (FROST - PRISM)

ERROR: COLOR 1 WHEEL POSITION

ERROR: FOCUS POSITION

ERROR: IRIS POSITION

ERROR: ROTATING GOBO WHEEL POSITION

ERROR: ROTATING GOBO INDEX POSITION

ERROR: FIXED GOBO WHEEL POSITION

ERROR: ZOOM POSITION

Up-DownENTER

PAN ALIGNMENT

To align pan

ENTER

Up-DownENTER

TILT ALIGNMENT

To align tilt

ENTER

Up-Down

ENTER

Up-DownENTERUp-Down

ROTATING GOBO WHEEL ALIGNMENT

To align the rotating gobo wheel

ENTER

Up-DownENTER

Up-Down

GOBO ROTATION ALIGNMENT

To align the gobo rotation (index)

ENTER

Up-DownENTERUp-Down

FOCUS ALIGNMENT

To align focus

ENTER

Up-DownENTERUp-Down

COLOR 1 ALIGNMENT

To align color wheel 1

ENTER

Up-DownENTERUp-Down

SHUTTER ALIGNMENT

To align shutter blades

ENTER

Up-DownENTERUp-Down

EFFECT ROTATION ALIGNMENT

To align prism on effects wheel (index)

ENTER

Up-DownENTERUp-Down

ZOOM ALIGNMENT

To align Zoom

ES.

ENTER

17- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

- Reset the XR700 SPOT (reset from the MENU, not from the DMX controller!).

- While reset is running, press the MENU and ENTER keys at the same time.

Electronic calibration of the motors.

Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must

repeat all previous calibrations)

Exit from hidden menu.

Up-DownENTERUp-Down

FIXED GOBO WHEEL ALIGNMENT

To align the fixed gobo wheel

ENTER

Up-DownENTER

Up-Down

ES.

ENTER

Up-DownENTERUp-Down

COLOR 2 ALIGNMENT

To align color wheel 2

ENTER

ARC 1200

XR700 SPOT

18

!

Up-Down

ES.

Up-DownENTER ENTER

EFFECTS ALIGNMENT

To align the effects wheel (frost and prism)

IRIS ALIGNMENT

To align iris

19

18- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

19- REPLACING GOBOS

XR700 SPOT uses a mechanical system which allows the fixture's gobos to be removed without the use

of special tools. Replacement gobos should be made of either heat resistant glass or metal.

An ever-increasing range of gobos is available from your DTS sales network.

Gobo dimensions are as follows:

ø external (ED) = 27.9 mm

ø of image with defined edge (ID) = 24 mm

thickness = from 0.2 to 4 mm (see catalogue)

Photo 1

Photo 2

ARC 1200

XR700 SPOT

Load with coated surface toward the light source.

Max thickness

Coated side

When an object is held up the coated side of the glass gobo there

is no space between the object and its reflection.

Uncoated side

When an object is held up the uncoated side of the glass gobo

there is a space between the object and its reflection.

Coated side

Uncoated side

ED

ID

4 mm

Replacing gobos on the rotating gobo wheel

When replacing gobos, ensure that the projector is switched off.

1) Open the projector housing as described above.

2) Remove the gobo holder to allow easier access to the gobo (photo 1).

3) Release the gobo retaining spring and carefully remove the gobo (photo 3).

4) Reverse the procedure to install a replacement gobo.

20- PERIODIC CLEANING

20.1- Lenses and reflectors

Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses

and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

20.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning

will depend of course, on the conditions in which the projector is operating. Suitable instruments

for performing this type of maintenance are a brush and a common vacuum cleaner or an air

compressor. If necessary, clean the fans and air passages more frequently.

21- PERIODIC CONTROLS

Attention

Disconnect mains power prior to removing the projector housing.

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will

help to avoid the danger of the lamp exploding.

XR700 SPOT lamp lifespan is about 750 hours, then it is necessary to replace it.

Mechanical parts

Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if

necessary. Periodically check the lubrication of all components, particularly the parts subject to

high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.

distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors,

refastening if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR700 SPOT

Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if

necessary.

20

ARC 1200

XR700 SPOT

Photo 1

Photo 3

!

UV

La pagina sta caricando ...

DTS XR700 SPOT Manuale utente

DTS XR700 SPOT Manuale utente

in altre lingue

Documenti correlati

Altri documenti