StarTech ARMBARDUOV Manuale del proprietario

Marca
StarTech
Modello
ARMBARDUOV
Tipo
Manuale del proprietario

Questo manuale è adatto anche per

Manual Revision: 12/04/2018
For the latest information, technical specications, and support for
this product, please visit www.StarTech.com/ARMBARDUOV.
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
ARMBARDUOV
Dual-Monitor Stand - Vertical
*actual product may vary from photos
Instruction manual
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other
countries.
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction manual
i
Varningsmeddelanden
Se till att du monterar produkten i enlighet med instruktionerna. Om du inte gör det kan skada på
person eller egendom uppstå.
Se till att skärmens vikt inte överstiger produktens viktkapacitet. Om viktkapaciteten överstigs kan
skada på person eller utrustning uppstå. Denna produkt har stöd för följande vikter: 10 kg per skårm.
Använd aldrig produkten om delar saknas eller är skadade.
Avertissements
Assemblez ce produit conformément aux instructions. Si vous ne respectez pas ces instructions, vous
risquez de vous blesser ou d’endommager l’équipement.
Vériez que le poids du moniteur ne dépasse pas la capacité pondérale du produit. Si vous dépassez
la capacité pondérale, vous risquez des blessures corporelles ou des dommages matériels. Ce produit
peut supporter 10 kg par ’ecran.
N’utilisez pas ce produit si des pièces sont endommagées ou manquantes.
Warnhinweise
Montieren Sie dieses Produkt gemäß den Anweisungen. Anderenfalls kann dies zu Verletzungen von
Personen oder Schäden an Eigentum führen.
Das Gewicht des Monitors darf die zulässige Traglast des Produkts nicht übersteigen. Wenn die Traglast
überschritten wird, kann dies zu Verletzungen von Personen oder Schäden an Geräten führen. Dieses
Produkt ist für folgendes Gewicht geeignet: 10 kg per monitor.
Das Produkt darf nicht bedient werden, wenn Teile fehlen oder beschädigt sind.
Dichiarazioni di avvertenza
Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle istruzioni potrebbe causare
danni a persone o proprietà.
Vericare che il peso del monitor non superi la capacità di supporto del prodotto. In caso di
superamento della capacità di supporto potrebbero vericarsi danni a persone o apparecchiature. Il
prodotto è in grado di supportare i seguenti pesi: 10 kg per monitor.
Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
Mensagens de aviso
Certique-se de que monta este produto de acordo com as instruções. O incumprimento pode resultar
em ferimentos pessoais ou danos de propriedade.
Certique-se de que o peso do monitor não excede a capacidade de peso deste produto. Se exceder
a capacidade de peso, pode sofrer ferimentos pessoais ou danos no equipamento. Este produto pode
suportar o seguinte peso: 10 kg por monitor.
Nunca opere este produto se faltarem peças ou estas estiverem danicadas.
Waarschuwingen
Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit niet goed gebeurt kan
lichamelijk letsel of materiële schade ontstaan.
Zorg dat het gewicht van het scherm de maximale capaciteit van dit product niet overschrijdt. Als u de
gewichtscapaciteit overschrijdt, kan persoonlijk letsel of schade aan de apparatuur ontstaan. Dit product
ondersteunt het volgende gewicht: 10 kg per monitor.
Gebruik dit product nooit als er onderdelen ontbreken of beschadigd zijn.
Warning statements
Make sure to assemble this product according to the instructions. Failure to do so might result in
personal injury or property damage.
Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you
exceed the weight capacity, you might experience personal injury or damage to the equipment. This
product can support the following weight: (10 kg) 22 lb. per monitor mount.
Never operate this product if parts are missing or damaged.
Advertencias de uso
Asegúrese de ensamblar este producto según las instrucciones. De lo contrario, pueden producirse
lesiones personales o daños de propiedad.
Asegúrese de que el peso del monitor no exceda la capacidad de carga de este producto. Si se excede
dicha capacidad se podrían producirse lesiones personales o daños al equipo. Este producto tiene
capicidad para el siguiente peso: 10 kg por monitor.
Nunca opere o ponga en funcionamiento este producto si faltan piezas o hay daños en las mismas.
注意
必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤った場合に、傷害を負う恐れ
や物的損害が発生する恐れがあります。
取り付けるモニターの重量が、本製品で定められた最大積載重量を超えないようにして下さい。最大積
載重量をオーバーした場合、傷害を負う恐れやモニターや本製品に損害が発生する恐れがあります。
本製品は、モニター1台あたり10kgまで支持できます。
本製品で使用している部品の一部が紛失していたり損傷している状態で使用するのは絶対に止
めて下さい。
Instruction manual
ii
Table of Contents
Warnings ......................................................................................................................................................i
Introduction ............................................................................................ 1
Product diagram ........................................................................................................................................1
Product dimensions ................................................................................................................................. 2
Technical specications .......................................................................................................................... 3
Package contents ...................................................................................................................................... 4
Requirements ............................................................................................................................................. 6
Assembly .................................................................................................7
Assemble the lower pole ........................................................................................................................7
Attach a VESA monitor mount..............................................................................................................8
Attach the upper pole ............................................................................................................................. 9
Attach the second VESA monitor mount.........................................................................................10
Attach monitors to the VESA monitor mounts ...............................................................................11
Adjust the tilt angle of your monitor .................................................................................................15
Adjust the monitors .................................................................................................................................16
Technical support ...................................................................................17
Warranty information ............................................................................ 17
Instruction manual
1
Introduction
Product diagram
Lower pole
Upper pole
Cable-management clip
Pole connector
Baseplate
Cable-management clip
VESA monitor mount
VESA monitor mount
Instruction manual
2
Product dimensions
48 mm
35 mm
75 mm
100 mm
113 mm
75 mm
100 mm
116 mm
818 mm
316 mm
434 mm
±45°
±45°
360°
Instruction manual
3
Technical specications
Type of measurement Measurement
VESA mounting hole pattern
75x75
100x100
Weight capacity
Up to 10 kg (22 lb.)
per monitor mount
Tilt
+45 to -45
Screen size
Between 330 mm and 686 mm
(13 in. and 27 in.)
Rotate
360
Swivel
+45 to -45
kg
Instruction manual
4
Package contents
Baseplate
Qty: One
Lower pole
Qty: One
Upper pole
Qty: One
Pole connector
Qty: One
VESA monitor mounts
Qty: Two
Cable-management clips
Qty: Two
2
1
3
4
65
Instruction manual
5
Cap
Qty: One
3 mm hex key
Qty: One
5 mm hex key
Qty: One
6 mm hex key
Qty: One
M4x12 mm screws
Qty: Eight
M5x12 mm screws
Qty: Eight
8
7
9 10
11
12
Instruction manual
6
Washers
Qty: Eight
Instruction manual
Qty: One
13 14
Requirements
• Two monitors or displays that are compatible with one of the mounting hole
patterns that ARMBARDUOV supports
• A Phillips screwdriver
Requirements are subject to change. For the latest requirements, please visit
www.StarTech.com/ARMBARDUOV.
Instruction manual
7
Assembly
Warning! Make sure that the weight of the monitors does not exceed the weight
capacity of this product. If you exceed the weight capacity, you might experience
personal injury or damage to the product.
This product can support the following weight: Up to 22 lb. (10 kg).
Assemble the lower pole
1. Thread the cable-management clip onto the pole.
2. Thread the cap onto the pole.
3. Screw the pole into the baseplate. (gure 1)
4. Use the 3 mm hex key to tighten the screws and attach the pole to the baseplate.
5. Push the cap down so that it sits ush against the baseplate and covers the screws.
(gure 2)
gure 1
Lower pole
Cable-management clip
Cap
Baseplate
gure 2
Cap
3 mm hex key
Baseplate
Cable-management clip
Instruction manual
8
Attach a VESA monitor mount
1. Slide one of the VESA monitor mounts down the lower pole. (gure 3)
gure 3
VESA monitor mounts
Lower pole
2. When the VESA monitor mount is at the desired height, use the 5 mm hex key to
tighten the screw at the back of the VESA monitor mount. (gure 4)
gure 4
5 mm hex key
VESA monitor mount
Instruction manual
9
Attach the upper pole
1. Screw the pole connector onto the lower pole.
2. Attach the other cable-management clip to the upper pole.
3. Screw the upper pole into the pole connector. (gure 5)
gure 5
Lower pole
4. Use the 3 mm hex key to tighten the two screws in the side of the pole connector.
(gure 6)
gure 6
Cable-management clip
Upper pole
Pole connector
Pole connector
3 mm hex key
Instruction manual
10
Attach the second VESA monitor mount
1. Slide the other VESA monitor mount down the upper pole. (gure 7)
gure 7
VESA monitor mount
2. When the VESA monitor mount is at the desired height, use the 5 mm hex key to
tighten the screw at the back of the VESA monitor mount. (gure 8)
gure 8
VESA monitor mount
Upper pole
5 mm hex key
Instruction manual
11
Attach monitors to the VESA monitor mounts
Warning! Attaching a monitor is a two-person job. Do not attempt to complete this
task by yourself.
Tipping hazard! The ARMBARDUOV is free-standing and when you attach monitors
to it, you increase the tipping hazard. A second person is required to keep the
ARMBARDUOV upright as you attach the monitors.
ARMBARDUOV is designed to be used with monitors that are the same size and weight.
If you attach monitors that are dierent sizes and weights to the ARMBARDUOV, you
do so at your own risk
Use the 100x100 VESA mounting hole pattern to attach a monitor
To accommodate dierent monitor sizes, the ARMBARDUOV comes with two sets of
screws that are dierent lengths and diameters.
To select the appropriate screws for the type of monitor that you’re using, complete
the following:
• Determine the depth of the mounting holes on the monitor.
• Determine the diameter of the mounting holes on the monitor.
1. Place two of the washers over the top two mounting holes on the back of the
monitor.
2. Insert two of the M4x12 mm screws or M5x12 mm screws through the washers
and into the back of the monitor. (gure 9)
Caution! At this point in the assembly, do not tighten the screws so that they are ush
against the monitor. To attach the monitor to the VESA monitor mount, you need to
leave a small gap between the screws and the monitor.
Monitor
M4x12 mm screw
or
M5x12 mm screw
Washer
gure 9
Instruction manual
12
3. Carefully hook the screws into the top two slots on the VESA monitor mount on the
upper pole. (gure 10)
gure 10
Monitor
M4x12 mm screw
or
M5x12 mm screw
VESA monitor mount
4. Use a Phillips screwdriver to tighten the screws. (gure 11)
Caution! If the VESA monitor mount starts to slip down the upper pole when you add
the weight of the monitor, remove the monitor and use the 5 mm hex key to tighten
the screw in the side of the VESA monitor mount. When the screw is tightened, repeat
step 3 to reattach the monitor.
Warning! Do not over-tighten the screws. If you encounter resistance while you’re
tightening the screws, stop tightening. Failure to do so could result in damage to the
monitor.
gure 11
Instruction manual
13
5. Place two washers over the mounting holes in the VESA monitor mount.
6. Insert two M4x12 mm screws or M5x12 mm screws through the washers, the
mounting holes in the VESA monitor mount, and into the back of the monitor.
(gure 12)
Warning! Do not over-tighten the screws. If you encounter resistance while you’re
tightening the screws, stop tightening. Failure to do so could result in damage to the
monitor.
7. Repeat steps 1 to 6 to attach a monitor to the VESA monitor mount attached to the
lower pole.
gure 12
Monitor
M4x12 mm screw
or
M5x12 mm screw
Washer
Instruction manual
14
Use the 75x75 VESA mounting hole pattern to attach a monitor
To accommodate dierent monitor sizes, the ARMBARDUOV comes with two sets of
screws that are dierent lengths and diameters.
To select the appropriate screws for the type of monitor that you’re using, complete
the following:
• Determine the depth of the mounting holes on the monitor.
• Determine the diameter of the mounting holes on the monitor.
1. Line up the mounting holes on the back of the monitor with the 75x75 mounting
holes in the VESA monitor mount on the upper pole.
2. While someone holds the monitor in place, insert the M4x12 mm screws or
M5x12 mm screws through the washers, the mounting holes in the VESA monitor
mount, and into the back of the monitor. (gure 13)
3. Use a Phillips screwdriver to tighten the screws.
Caution! If the VESA monitor mount starts to slip down the upper pole when you add
the weight of the monitor, remove the monitor and use the 5 mm hex key to tighten
the screw in the side of the VESA monitor mount. When the screw is tightened, repeat
step 2 to reattach the monitor.
Warning! Do not over-tighten the screws. If you encounter resistance while you’re
tightening the screws, stop tightening. Failure to do so could result in damage to the
monitor.
4. Repeat steps 1 to 3 to attach a monitor to the VESA monitor mount attached to the
lower pole.
gure 13
Monitor
VESA monitor mount
M4x12 mm screw
or
M5x12 mm screw
Washer
Instruction manual
15
Adjust the tilt angle of your monitor
1. To change the angle that a monitor is tilted at, use the 6 mm hex key to turn the
screw in the side of the VESA monitor mount counterclockwise.
2. When the screw is loose, position the monitor at the angle that works best for you.
3. Use the 6 mm hex key to turn the screw clockwise to tighten it. (gure 14)
+45°
-45°
6 mm hex key
gure 14
4. When you’re done adjusting the tilt angle, you can store the 5mm hex key and the
6 mm hex key in the hex key holder in one of the cable-management clips.
(gure 15)
gure 15
Hex key holder
Instruction manual
16
Adjust the monitors
360°
360°
-45°
+45°
-45°
+45°
La pagina si sta caricando...
La pagina si sta caricando...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

StarTech ARMBARDUOV Manuale del proprietario

Marca
StarTech
Modello
ARMBARDUOV
Tipo
Manuale del proprietario
Questo manuale è adatto anche per
Scarica PDF
rapporto

in altre lingue

Documenti correlati

Altri documenti