AJA OG-ROI-DVI Manuale utente

Marca: AJA

Modello: OG-ROI-DVI

Categoria: Apparecchiature musicali supplementari

Tipo: Manuale utente

Questo manuale è adatto anche per

OG-ROI-HDMI

OG-ROI Series

Region of Interest Converters

HDMI-to-SDI, DVI-to-SDI Scalers

Version 1.6

Published January 27, 2020

Installation and Operation Guide

OG-ROI Series openGear card v1.6 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of

AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and

V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web https://www.aja.com

Support Email suppor[email protected]

Sales Email [email protected]

OG-ROI Series openGear card v1.6 3 www.aja.com

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Video Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Audio Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

HDCP Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pixel Clock Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

OG-ROI Processing Capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Simplied Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

openGear and AJA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OG-ROI-HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OG-ROI-DVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Analog Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SDI Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Reference Video Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Signal Indicators on the OG-ROI Series Card. . . . . . . . . . . . . . . . . . . . .9

DashBoard Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rear OG-ROI Series Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . 10

Front OG-ROI Series Card Installation . . . . . . . . . . . . . . . . . . . . . . . . 11

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Typical ROI Congurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Using the DashBoard Control System. . . . . . . . . . . . . . . . . . . . . . . . . . 17

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Control Interface Basic Components . . . . . . . . . . . . . . . . . . . . . . . . 17

Input Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Click and Drag Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Output Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

About the Rotation, Flip, and Frame Delay Controls . . . . . . . . . . . . . . . 24

Monitor Matrix Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Genlock Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Audio Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Upload Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Rebooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 33

OG-ROI-HDMI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

OG-ROI-DVI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . .37

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . .45

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . . 45

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Contents

OG-ROI Series openGear card v1.6 4 www.aja.com

Chapter 1 – Introduction

Overview

AJA’s OG-ROI family of scalers/scan converters provide exceptionally high quality

conversion of computer and video signals in an openGear form factor. The OG-

ROI models offer Region of Interest (ROI) support allowing DVI and HDMI input

signals to be scaled and converted to a SDI output. With incredible image scaling,

extensive aspect ratio and frame rate conversion, OG-ROI fulfills the need to scale

computer and video to a desired resolution, all in realtime.

The two models of OG-ROI openGear cards available are:

• OG-ROI-DVI

• OG-ROI-HDMI

Designed for use in high-density openGear 2RU frames, including AJA’s OG-X-

FR 2RU frame, the OG-ROI Series is capable of communicating with Ross Video’s

DashBoard Control System. DashBoard runs on Windows®, macOS®, and Linux®,

providing convenient, industry-standard configuration, monitoring and control of

the openGear architecture over a PC or local network.

Video Processing

In default mode, the OG-ROI-DVI and OG-ROI-HDMI models automatically detect

the input signal format and convert it to the SDI output video format. Their

respective DVI and HDMI outputs pass the signal through without any processing,

maintaining the incoming signal aspect ratio.

In Auto mode, if there is a difference in aspect ratio relative to the input and

output format, the unused area is filled with a user-configurable matte color. For

example, a 720p input will matte with a 625i output and vice versa. However, a

720p input will not matte with a 1080p output.

Audio Handling

Analog audio from the host can be input via 3-pin analog audio connectors

and mapped to the embedded SDI output stream. Alternatively, when an HDMI

input signal is present, the HDMI input's embedded audio can be mapped to the

embedded SDI output stream.

OG-ROI Series openGear card v1.6 5 www.aja.com

The OG-ROI-DVI model can receive both DVI and HDMI protocol input, and

accepts audio if it is embedded in an HDMI signal. However, the DVI protocol does

not carry audio, so if the OG-ROI-DVI is receiving DVI input, only analog audio can

be embedded to the output.

HDCP Protection

The OG-ROI honors HDCP, and will not allow an HDCP link. If the input content is

HDCP protected, no source video will be displayed on the OG-ROI’s DVI pass-

through connector, or on the OG-ROI’s SDI output.

Features

OG-ROI-DVI

• Converts DVI input to 3G, HD, or SD-SDI output

OG-ROI-HDMI

• Converts HDMI input to 3G, HD, or SD-SDI output

Both OG-ROI Models

• openGear compatible card (requires 2 slots, rear card included)

• Use with openGear 2RU frames

• Controlled by DashBoard network control software

• High quality scaling and scan conversion

• User-adjustable “region of interest,” separate controls for input and output

• 4:3/16:9 conversion modes supported

• Frame-rate conversion

• Automatic configuration to input video raster and frame rate

• SDI output configurable to most common SD, HD and 3G formats (1080p 60

max)

• Edge filtering control

• Rotation, Horizontal and Vertical flip controls

• Monitor Matrix setup controls

• Frame delay control

• Rear card external reference input select

• OG frame reference input 1 select

• OG frame reference input 2 select

• Rear card reference input 75 ohm termination select

• Adjustable Horizontal and Vertical video delay from sync input

• Audio input via 3-pin analog audio connectors or 8-channel embedded (if

present)

• Embedded SDI audio out (up to 8 channels)

• 5-year warranty

Pixel rates are limited to a 165MHz maximum rate.

OG-ROI Series openGear card v1.6 6 www.aja.com

Pixel Clock Rate

The source video pixel clock is a combination of the video resolution and its

vertical rate. Some sources can generate pixel clock rates that exceed the

capabilities of the OG-ROI-DVI and OG-ROI-HDMI converters. It may not be

obvious what the resulting pixel clock will be for a particular resolution or vertical

rate.

For example, when a downstream sink device is connected to the OG-ROI output

monitor connector, the source and sink could potentially negotiate a display

format (using EDID) that is beyond the capability of OG-ROI’s video processing

circuitry.

When this error occurs, an “Exceeds max rate” yellow alarm message will be

displayed on the DashBoard user interface, and the OG-ROI will generate a full

screen red matte on the SDI output. A downstream DVI/HDMI/SDI monitor will

still display the incoming video.

Possible solutions include:

• Disconnect the downstream device (for example, a computer monitor) from

the OG-ROI. Once disconnected, OG-ROI will negotiate directly with the

source to generate a video resolution that is within the OG-ROI’s processing

capability.

• Reconfigure the source signal to a resolution that OG-ROI supports.

OG-ROI Processing Capabilities

The OG-ROI models utilize a powerful scaling processor, however, some specific

combinations of input and output OG-ROI selections, de-interlacing, and 180°

rotations or flips can exceed the processing capacity of the OG-ROI cards.

In these cases, a “Processing Limit Exceeded” red error message is displayed on

the DashBoard user interface, and the OG-ROI will automatically turn off certain

features in order to process the picture. These features that have been turned off

will be reported and will be in red. For an example, see "Processing Limit Exceeded"

on page 25.

Possible solutions include:

• Reduce the size of the Region of Interest selections; input OG-ROI, output OG-

ROI, or a combination of both.

• Turn off 180 degree rotation and/or H and V flips, or frame delay.

• Use a progressive rather than interlace input signal.

OG-ROI Series openGear card v1.6 7 www.aja.com

Simplified Block Diagram

Figure 1. OG-ROI Converter/Scaler, Simplified Block Diagram

Reference

Input

3-Pin

Analog Audio

Connectors

Input

Pass-Thru Path

Free Run

Audio Delay

Audio ADC

8 CH

SRC

Processed

SDI Output

HDMI/DVI

Video Input

OG-ROI Model

Input and Output

Connectors:

Embedder

OG-ROI-DVI

DVI-D

Connector

OG-ROI-HDMI

HDMI

Connector

Unprocessed

Video Output

Sync Stripper

InterlacerFRC/Genlock

Deinterlacer KeyerROI Scaler

Matte Gen

HDMI/DVI/

SDI Output

ControlDashBoard

openGear and AJA

openGear is an open-architecture, modular frame system designed by Ross

Video and supported by a diverse range of terminal equipment manufacturers,

including AJA. Ross Video manufactures the frames, power supplies and network

cards for openGear. AJA is a reseller of the openGear frames.

AJA Video is a leading manufacturer of video interface technologies, converters,

digital video recording solutions and professional cameras, bringing high-

quality, cost-effective products to the professional, broadcast and post-

production markets. AJA products, including openGear cards, are designed and

manufactured at our facilities in Grass Valley, California.

I/O Connections

OG-ROI-HDMI

Figure 2. I/O Connections for the OG-ROI-HDMI Converter/Scaler

SDI Output

BNC (J1)

HDMI Input

Reference

Input

BNC (J2)

(inactive)

HDMI Output

Analog Audio

Input L

Analog Audio

Input R

(inactive)

HDMI Input

Connects to your computer or single-link source device.

OG-ROI Series openGear card v1.6 8 www.aja.com

To connect a DVI video input to the OG-ROI-HDMI input connector, use a passive

DVI-to-HDMI adapter (user-supplied). You can also use a cable adapter that has a

DVI connector on one end of the cable and an HDMI connector on the other.

HDMI Output

This is a pass-through output for use on a second computer monitor. Connections

are the same as described for DVI/HDMI input above.

OG-ROI-DVI

Figure 3. I/O Connections for the OG-ROI-DVI Converter/Scaler

SDI Output

BNC (J1)

DVI Input

Reference

Input

BNC (J2)

DVI Output

Analog Audio

Input L

Analog Audio

Input R

DVI Input

Connects to your Computer or single-link source device.

To connect an HDMI video input to the ROI DVI input connector, use a passive

HDMI-to-DVI adapter (user-supplied). You can also use a cable adapter that has an

HDMI connector on one end of the cable and a DVI connector on the other.

DVI Output

This is a pass-through output for use on a second computer monitor. Connections

are the same as described for DVI/HDMI input above.

Analog Audio

Two 3-pin analog audio connectors accept two channels of analog audio which

can be embedded into the SDI output as determined by the audio configuration

set using DashBoard.

SDI Video Output

The SDI output BNC delivers the processed output signal which has scaling,

region of interest, converted raster, converted frame rate, and embedded audio.

Reference Video Input

The Reference BNC accepts an Output timing reference signal. The reference can

be SD Blackburst or HD tri-level sync.

OG-ROI Series openGear card v1.6 9 www.aja.com

Signal Indicators on the OG-ROI Series Card

Located at the upper front area of the OG-ROI Series card, the LEDs shown in

Figure 4 below indicate the status of the card's power, signal presence and signal

lock.

Figure 4. LED lights on card

Power LED

Signal Present LED

Signal Locked LED

Power LED

The Power LED indicates the state of the card as displayed in DashBoard. It can be

green, yellow or red.

• Green: no DashBoard card state alarm is present.

• Yellow: a yellow DashBoard card state alarm is present. See DashBoard for

more information.

• Red: a red DashBoard card state alarm is present. See DashBoard for more

information.

Signal Present LED

The Signal Present LED can be green or off.

• Green: incoming signal has been identified and acquired.

• Off: no signal is detected.

Signal Lock LED

The Signal Locked LED can be solid green, blinking green, or off.

• Solid Green: The signal detected matches the reference selected (Auto, HDMI,

Ref In, Free Run) from the Genlock control on the Genlock tab in DashBoard.

Note that in DashBoard, the Status tab shows what signal you are locked to

(HDMI, Reference Input, or Free Run).

• Blinking Green: A signal is present, but it does not match the reference

selected in DashBoard.

• Off: No reference is present.

OG-ROI Series openGear card v1.6 10 www.aja.com

DashBoard Control System

IMPORTANT: DashBoard version 8.5.1 or later is required to support the OG-ROI-HDMI

and OG-ROI-DVI cards.

The DashBoard Control System, created by Ross Video, provides a control

interface between Windows, macOS and Linux computers and the cards installed

in an openGear frame. DashBoard operates through TCP/IP communication

and requires an Ethernet connection between the controlling computer and an

openGear frame.

Details for acquiring and using the DashBoard Control System are provided in

"Using the DashBoard Control System" on page 17.

Parts List

Quantity Description

1 OG-ROI Series Front Card in ESD bag

1 DVI / HDMI Rear Card

2 WECO mating connectors, part number

107654-00

Installation

Summary

Installing an OG-ROI Series card into an OG-X-FR or OG-3-FR openGear frame

consists of the following steps:

• Install the Rear Panel onto the back of the frame corresponding to the slot pair

you will be using for the OG-ROI Series card.

• Insert the OG-ROI Series card into the frame in the right (even numbered) slot

of the pair.

• Connect the BNC and audio cabling to the Rear Panel.

ESD Susceptibility - Static discharge can cause serious damage to sensitive

semiconductor devices. Avoid handling circuit boards in high static

environments such as carpeted areas, and when wearing synthetic fiber

clothing. Always exercise proper grounding precautions when working on circuit

boards and related equipment.

Unpacking

Unpack each openGear product you received from the shipping container and

ensure that all items are included. If any items are missing or damaged, contact

your sales representative or AJA directly.

Rear OG-ROI Series Card Installation

1. Ensure that the frame is properly installed.

2. Locate the card frame slot on the rear of the openGear frame into which you

wish to install the openGear card.

NOTE: An OG-ROI Series card occupies two slots in the frame.

OG-ROI Series openGear card v1.6 11 www.aja.com

3. Using a Phillips screwdriver, unscrew the top screw from the desired blank

rear plate and remove the rear plate.

4. Seat the bottom of the Rear Card in the seating slot at the base of the frame

back plane.

Figure 5. Rear Card Inserting Into Frame Seating Slot

5. Align the top screw of the Rear Card with the screw hole on the top edge of

the frame back plane.

6. Ensure the Rear Card aligns with the desired card slot before tightening the

screw.

7. Using a Phillips screwdriver, fasten the Rear Card to the frame back plane.

Do not over tighten.

Figure 6. Rear Card Inserted Into Frame Seating Slot

8. Ensure proper frame cooling and ventilation by having all rear frame slots

covered with rear modules or blank metal plates if plates are not pre-

installed.

Front OG-ROI Series Card Installation

1. Open the openGear frame door as follows:

A. Gently pull the side door tabs towards the center of the door, releasing the

door from the frame.

B. Using both hands, pull the door towards you. The door extender arms

prevent the door from falling.

OG-ROI Series openGear card v1.6 12 www.aja.com

2. Locate the Rear Card you installed as described above. The interior slot

number is dependent on the slot combinations into which you installed the

Rear Card. This allows adequate spacing to avoid damaging the card, the

cards installed in the neighboring slots, or both.

3. Hold the card by the edges and carefully align the card edges with the rails

inside the frame. The slots are numbered starting from the left-most slot

when facing the frame front.

IMPORTANT: OG-ROI Series cards are installed into the right (even numbered) slot of the

pair in order to connect with the rear panel.

4. Fully insert the card into the frame until the card is properly seated in the

Rear Card. There are two stages to inserting the card:

A. After you feel the card's first click, its position in the frame will resemble the

photograph below in Figure 7.

B. Next, press against the white plastic tab again until you feel the second

click. The card's position will resemble the photograph below in Figure 8.

WARNING: Some cards require more pressure than others to be fully inserted.

Make sure that the plastic tab at the bottom of the front edge of the card is

completely upright. If it is tilting forward, the card is not yet fully inserted.

Figure 7. The card on the right is already fully inserted. The card to its left

(second from the right) is not yet fully inserted, as indicated by the white

plastic tab tilting forward.

OG-ROI Series openGear card v1.6 13 www.aja.com

Figure 8. The white plastic tab for the card second from the right is now

upright. All cards are shown fully inserted.

5. Close the frame door as follows:

A. Slide the door into the frame.

B. Pull and release the door tabs to ensure the frame door is securely locked

to the frame.

Cabling

Refer to "I/O Connections" on page 7 to identify the input and output signal

connectors.

Two WECO audio mating connectors are included with each OG-ROI Series card.

1. Insert connecting audio wires into their corresponding holes from the rear

(Figure 9).

Figure 9. Rear view of the WECO mating audio connector

2. Tighten the screws on the other side of the audio mating connector (Figure

8).

Figure 10. Front view of the WECO mating audio connector showing the

tightening screws

OG-ROI Series openGear card v1.6 14 www.aja.com

3. After you have secured the wiring for each WECO mating audio connector,

connect them to the audio output connectors on the rear panel of the

OG-ROI Series card.

4. Add tie wraps around the audio connectors for strain relief.

Typical ROI Configurations

This section covers six example configurations of OG-ROI.

Two typical configurations for using the OG-ROI for scaling of desktop region-

of-interest computer-sourced video are illustrated in the following two figures.

In these configurations, the pass-through monitor is used to view the subject

desktop video.

Figure 11. OG-ROI with Laptop Computer, System Interconnect Diagram

OG-ROI

HDMI/DVI

Ethernet

SDI Output

Source Computer

w/ DashBoard

Video

Monitor

Computer Desktop

Monitor

(ROI Pass-through)

Figure 12. OG-ROI with Tower Computer & Two Monitors, System Interconnect

Diagram

OG-ROI

Ethernet

SDI Output

Source Computer

Tower

w/ DashBoard

Video

Monitor

Computer

2nd Desktop

Monitor

(ROI Pass-through)

Computer Desktop

Monitor

Monitor 2 Out

Monitor 1 Out

HDMI/DVI

OG-ROI Series openGear card v1.6 15 www.aja.com

A third example (Figure 13) illustrates use of the OG-ROI Rotation feature to

send selected areas of a SDI signal to portrait mounted on-set monitors at full

resolution. Each monitor uses one OG-ROI converter, accomplishing the task at a

much lower cost than dedicating DVE channels for rotation and resizing.

Figure 13. OG-ROI Rotation with Portrait Mounted On-Set Monitors

OG-ROI B

Ethernet

HDMI Output

OG-ROI A

Portrait

SDI Monitors

Built Into Set

Region

HDMI/DVI

Loop-Through

- Input ROI Selection: 9x16 Fixed Aspect

- Output ROI Out Scaling: Full Screen Rotated 90 Degrees

SDI converted to

HDMI/DVI

Digital Video

Camera

Computer

w/ DashBoard

A fourth example below illustrates sending HDMI digital video from a camera to

an OG-ROI to allow region of interest video input to a video switcher.

Figure 14. OG-ROI-HDMI with Video Camera to Switcher Interconnect

Diagram

OG-ROI

HDMI

Ethernet

SDI

Output

Computer

w/ DashBoard

Video Switcher

Digital Video

Camera

Computer Desktop

Monitor

(ROI Pass-through)

SDI converted to

HDMI/DVI

In a parallel configuration as Figure 14, Figure 15 below shows a basic

configuration of the OG-ROI being used to send a 3G-SDI digital video signal

from a 3G-HDMI or 3G-DVI source to allow region of interest video input to a

video switcher. You can use methods for adjusting the region of interest selection

described in the section for the "Input Screen" on page 19 with the processed

3G-SDI output signal feeding a monitor.

OG-ROI Series openGear card v1.6 16 www.aja.com

Figure 15. OG-ROI-HDMI or OG-ROI-DVI with HDMI or DVI Source to Switcher

Interconnect Diagram

OG-ROI

HDMI/DVI

Ethernet

SDI

Output

Computer

w/ DashBoard

Video Switcher

HDMI/DVI Monitor

HDMI/DVI Source

OG-ROI Series openGear card v1.6 17 www.aja.com

Chapter 2 – Operation

IMPORTANT: Once you have configured the OG-ROI card using DashBoard, and as long

as the input format remains the same, the settings will persist when the frame

is disconnected from a controlling computer (in stand-alone mode). If you

anticipate that the input format may change, and if the current configuration

settings wouldn't make sense for a different input format, you can enable Auto

Bypass Mode (Auto Bypass Mode checkbox is selected from the Input tab). When

enabled, Auto Bypass Mode forces the OG-ROI card to use Auto in all applicable

settings when the input format changes. When the original input format is

re-connected, the OG-ROI will exit Auto Bypass Mode and restore all previously

configured settings for that format.

Using the DashBoard Control System

The DashBoard Control System, created by Ross Video, is available as a free

download from the Ross Video website:

https://www.rossvideo.com/products-services/management-systems/

automated-production-control/dashboard/

Ross Video offers comprehensive documentation that covers the extensive

capabilities of the DashBoard Control System:

https://www.rossvideo.com/support/product-documentation/dashboard/

This manual addresses only those essential aspects of the DashBoard Control

System needed to control the OG-ROI Series cards.

Requirements

The DashBoard Control System requires the following components:

• openGear frame with a Frame Controller card

• Ethernet connection betweeen the controlling computer and the openGear

frame

NOTE: The openGear frame ships from AJA with the MFC-8322-S Frame Controller card

for controlling the new AJA DashBoard cards. The openGear frame also supports

the MFC-0G3-N Advanced Networking Frame Controller card, which can be used

to control compatible OG cards.

IMPORTANT: DashBoard version 8.5.1 or later is required to support the OG-ROI-HDMI

and OG-ROI-DVI cards.

DashBoard automatically discovers openGear and DashBoard Connect devices,

such as openGear frames and cards that are present and accessible on your

network.

Control Interface Basic Components

The basic components of the DashBoard Control System user interface consist of

the basic tree view of frames and cards, the card information and status panel,

and the parameter controls panel. These elements are shown below in Figure 14.

Main Sections of the DashBoard User Interface.

The basic tree view of frames and cards shows the frames and cards that are

discoverable by DashBoard on your network.

The card information and status panel, shown in the middle panel, display the

basic status of the card currently selected in DashBoard.

OG-ROI Series openGear card v1.6 18 www.aja.com

The parameter controls panel shows the tabs and parameters that the selected

card has available for configuration and control.

Figure 16. Main Sections of the DashBoard User Interface

Parameter

Controls

Card Information

and Status

Basic Tree View of

Frames and Cards

OG-ROI Series openGear card v1.6 19 www.aja.com

Input Screen

Proxy Screen

Click on the Input tab to view and make changes to the converter’s input region-

of-interest settings.

An input signal is required before the Input menu configuration controls are

available. When no input signal is present, the OG-ROI unit grays out the Input

menu controls.

The Proxy Screen shows the current region of interest setting in green with the

selection pixel size at the bottom and the input pixel size at the top. Various

controls are also available on the left.

NOTE: The adjustments made on the green proxy screens are live and can be viewed

on the SDI output.

NOTE: Portions of this screen are grayed out if no input signal is present.

ROI Selection

Using this pulldown menu you can choose a selection mode:

Auto - Selects the entire signal detected at the input to the ROI (default setting).

Scales the input region-of-interest as large as possible to fit into the SDI

output region while maintaining the incoming aspect ratio. Matte may result if

the input’s aspect ratio does not match the SDI out aspect ratio.

NOTE: Auto selections in the Input screen and the Output screen are linked. Selecting

Auto from one screen will also select Auto in the other screen.

OG-ROI Series openGear card v1.6 20 www.aja.com

Variable - Allows user-adjustable selection of all or a portion of the input signal.

When you select Variable as the selection type, you can choose the region-of-

interest selection in three ways with no constraints:

• Use the X,Y coordinates and W,H (width, height) size fields. Within these

fields, you can enter values (if they are valid) or use your keyboard arrow

keys to increment one pixel/line at a time for fine adjustment.

• If configuring a multiple monitor matrix, you can use the Monitor Matrix

screen to select the ROI and, when applied, will fill the X, Y, W, and H fields

with the correct values. See "Monitor Matrix Screen" on page 26.

• Drag the edges of the image representation (green proxy screen) at the

right of the selection pane. See "Click and Drag Options" on page 21.

Fixed Aspect - Opens a ROI Fixed Aspect drop-down menu allowing fixed

aspect input region-of-interest selection. In this mode, the size of the selected

region-of-interest can change but the aspect ratio is held constant:

• 4:3 (SD aspect ratio)

• 16:9 (HD aspect ratio)

• 3:4 (useful for presentation on vertically oriented monitors)

• 9:16 (useful for presentation on vertically oriented monitors)

NOTE: Pixel aspect ratio (PAR) is accounted for in fixed aspect mode. The storage aspect

ratio will change based on the input's PAR to achieve a display aspect ratio

equivalent to your configured settings.

Fixed Size - Opens a ROI Fixed Size drop-down menu allowing fixed size input

region-of-interest selection. In this mode, the region-of-interest selection can

change position on the input screen but the size cannot be changed. These

settings allow you to easily select standard video sizes for region-of-interest.

• DV

• NTSC

• PAL

• 720HD

• 1080HD

SDI Out - Forces the region-of-interest to have the same aspect ratio as the

current SDI Out Format setting.

RGB Range Menu

The RGB Range pulldown menu allows you to select either Full range (0-1023) or

SMPTE range (typically 64-940) for RGB color input.

Full Screen Button

Click the Full Screen button to set the region-of-interest to the full input raster

size.

Center Button

If you choose anything other than a full-sized image (Auto) in the ROI Select

menu, you will have complete control of where the region of interest selection

is placed. To quickly and precisely center the region-of-interest, click the Center

button.

Auto Bypass Mode

Once you have configured the OG-ROI card using DashBoard, and as long as

the input format remains the same, the settings will persist when the frame is

disconnected from a controlling computer (in stand-alone mode).

La pagina si sta caricando...

AJA OG-ROI-DVI Manuale utente

Marca: AJA

Modello: OG-ROI-DVI

Categoria: Apparecchiature musicali supplementari

Tipo: Manuale utente

Questo manuale è adatto anche per

OG-ROI-HDMI

Scarica PDF

rapporto

in altre lingue

English: AJA OG-ROI-DVI User manual
Deutsch: AJA OG-ROI-DVI Benutzerhandbuch

AJA OG-ROI-DVI Manuale utente

Questo manuale è adatto anche per

AJA OG-ROI-DVI Manuale utente

in altre lingue

Documenti correlati

Altri documenti