Belkin 8820ed00380_F7D4302_v1 Manuale utente

Play WIRELESS ROUTER

User Manual

8820ed00380_F7D4302_v1

English

Français

DEutsch

nEDErlanDs

TABLE OF CONTENTS

Getting Started ........................................... 3

What’s in the Box ............................................. 3

Initial Setup .................................................. 3

Advanced Tools & Settings..................................... 8

The Belkin Router Manager .................................... 9

Manual Setup Using Your Browser ............................. 10

Adding Computers to Your Network ............................ 11

Adding USB Devices ......................................... 13

Bundled Software ........................................... 16

Additional Capabilities ....................................... 18

Getting to Know Your Router .............................. 19

Front Panel ................................................. 19

Back Panel .................................................20

Technical Features .......................................... 21

Technical Details ........................................22

System Requirements ........................................22

Troubleshooting, Support, and Warranty ...................24

Troubleshooting ............................................. 24

Belkin International, Inc., Limited 2-Year Product Warranty .........34

Regulatory Information ................................... 37

FCC Statement.............................................. 37

3

What’s in the Box

Play Wireless Router

Ethernet cable (attached to router)

Power supply (attached to router)

Network information card (attached to router)

Belkin Setup CD with User Manual

Initial Setup

Where to Place Your Router

For the best results, place the Router next to your modem in

an open location away from large metal objects and magnets

such as those found in speakers. Raising the Router above

floor level can improve the strength of your wireless signal.

GETTING STARTED

4

GETTING STARTED

How to Set It Up

2 3

modem

1

5

GETTING STARTED

1. Connect your Router’s Ethernet cable to your modem’s Ethernet

port (on the back of your modem). This port might be labeled

differently on your particular modem. If you are adding a

Router for the first time, this port may be connected to your

computer by an Ethernet cable. It is OK to disconnect your

computer and plug the Router into the modem instead.

2. Plug the Router’s power supply into a wall outlet.

3. Put the CD into your computer. If the CD doesn’t

open automatically, please browse to your CD drive

and double-click on the Belkin Setup CD icon.

4. Click the Setup icon on the CD menu.

Setup

6

GETTING STARTED

5. After a brief installation, the setup software will ask you

for the network name and password from the network

information card that is attached to your Router. Store the

card under the base of your Router for future reference.

7

GETTING STARTED

6. A progress screen will appear while additional software is

installed. This may take a few minutes to complete. Once

finished, a “Success” message will appear indicating that you

are connected to the Internet via your new Belkin Router.

During setup you may be asked for additional information.

You may need to enter a username and password provided

by your ISP. This username and password is likely to be

found on materials that came from your ISP when you

signed up for service. If necessary, you may need to contact

your ISP to retrieve your username and password.

If you have a static IP address, you may need to enter

additional information also provided by your ISP.

If your computer doesn’t have a wireless adapter, or the

setup software is unable to control it, you may be asked to

connect your computer to the Router with a network cable.

8

GETTING STARTED

Advanced Tools & Settings

After the initial setup is complete, you have the option to

change settings like your network name, security type, and

password. To make these changes and others, click on the

Advanced Tools icon at the CD Setup menu and select one

of the following settings that you would like to change:

Network Name & Security – Personalize your network name

(SSID), password, and strength of wireless security.

Internet Service Provider & Login Settings – Have

you moved or changed Internet Service Providers?

If you’d like to change these settings without running

through the setup process again, this is the place.

9

GETTING STARTED

The Belkin Router Manager

Belkin.2234

Router Settings

User Manual

USB Print & Storage Manager

Memory Safe: Get Started!

Daily DJ: Get Started!

Music Labeler

Check for Updates

Options

Exit

The Belkin Router Manager appears in your system tray

(Windows) or menu bar (Mac). Its icon indicates the current

status of your Router and also allows you to access your

Router’s settings to make changes. It also provides quick

access to software that came bundled with your Router.

To access the Router settings, click on the icon

and select from the menu that appears.

The status of your Router is shown by the Belkin Router Manager

icon, which closely mimics the light on the front of the Router.

Green: You are connected to your Belkin Router

and it is connected to the Internet.

Amber: You are connected to your Belkin Router,

but it is not connected to the Internet.

10

GETTING STARTED

In your browser, type “http://router” (you do not need to type

in anything else such as “www”). Then press the Enter key. If

you’re still having trouble running the manual setup option, type

“192.168.2.1” in your browser (you do not need to type in anything

else such as “http://” or “www”). Then press the Enter key.

Manual Setup Using Your Browser

11

GETTING STARTED

Adding Computers to Your Network

Wireless devices such as computers, network printers, and gaming

systems can connect to your Router with a few simple steps.

Using the CD

1. Put the Setup CD into your computer. If the CD

doesn’t open automatically, browse to your CD

drive and open the Belkin Setup CD icon.

2. Click the Setup icon on the CD menu.

3. After a brief installation, the setup software will ask you for the

network name and password from the network information card

that came with your Router. This card is most likely now located

underneath the foot of your Router in the provided card slot.

4. A progress screen will appear while additional software is

installed. This may take a few minutes to complete. Once

finished, a “Success” message will appear indicating that you

are connected to the Internet via your new Belkin Router.

Note: The setup software runs only on

Windows and Mac OS X systems.

12

GETTING STARTED

Manually

If you choose not to use the included Setup CD for

adding additional computers or wireless devices, you

can manually add these items to your network.

1. Locate the wireless-network-connections option

on your computer or wireless device.

2. Select your Belkin Router from the list of available networks. You

can identify your Belkin Router by locating the network name

(SSID) from the card located underneath the foot of your Router.

3. Enter your network password (located on

your network information card).

Your wireless device will take a few moments to connect to your

network. If the connection is not made the first time, try this

process again. If you still have difficulty connecting to your network

after trying this process a few times, see the “Troubleshooting”

section in this manual for help with connecting to your network.

Note: In some cases you may be prompted to select the

security type. It is printed on the card for your convenience.

Using the WPS Button

1. Start WPS Push Button Connection (WPS PBC) on your

computer or other Wi-Fi device that you would like to connect

wirelessly to your Router. Often there will be a button for this

purpose in software that came with the device, or a physical

“WPS,” “PBC,” or “Security” button on the device itself.

2. Within two minutes, press the WPS button on your Router.

The WPS light (small light above WPS button) will blink green while

it listens for your Wi-Fi device. Once a connection is established, the

light will turn green and then go out. If a connection is not established,

the light will blink amber. You may repeat the process to try again.

You can repeat this process for each WPS-enabled

device you’d like to add to your network.

13

GETTING STARTED

Adding USB Devices

USB

14

GETTING STARTED

Adding a Drive

You can share a USB hard drive or flash drive to your network via

your Router’s USB port. Once connected, you can share files and

music with other computers and devices within your network.

Plug your USB hard drive into the USB port on the back

of your Router. When the light above the USB port is lit,

your drive is available to computers on your network.

You can manually check the status of your shared drive by visiting

the USB Print and Storage Manager, found under the Belkin Router

Manager icon displayed in your system tray (Windows) or menu

bar (Mac). If you have difficulty sharing a drive on your network,

please see the “Troubleshooting” section of this manual.

Adding a Printer

You can add a printer to your network via your Router’s

USB port. Once connected, you can print from various

computers and wireless devices within your network.

Plug your printer’s USB cable into the USB port located on

the back of your Router. When the light above the USB port is

lit, your printer is available to computers on your network.

You can manually check the status of your printer by visiting the

USB Print and Storage Manager, found under the Belkin Router

Manager icon displayed in your system tray (Windows) or menu

bar (Mac). If you have difficulty sharing a printer on your network,

please see the “Troubleshooting” section of this manual.

Note: Each computer that will use the printer must have

both the Belkin software and the printer’s driver installed.

If the print driver is not installed, you will be asked to install

it by the Belkin USB Print and Storage Manager.

15

GETTING STARTED

Adding Other USB Devices

Other USB devices may also be shared via your Router.

Plug your device into the USB port located on the back of

your Router. When the light above the USB port is lit, your

device is available to computers on your network.

Computers running the Belkin USB Print and Storage Manager will

be able to make use of the shared device by visiting the USB Print

and Storage Manager, found under the Belkin Router Manager

icon displayed in your system tray (Windows) or menu bar (Mac).

16

GETTING STARTED

Bundled Software

USB Print and Storage Manager

The USB Print and Storage Manager helps to manage and

monitor the use of your USB printers, scanners, hard drives,

and other devices that are connected to your Router’s USB

port and shared across your network. USB Print and Storage

Manager is found in the Belkin Router Manager icon displayed

in your system tray (Windows) or menu bar (Mac).

When you have one or more USB devices attached to your

Router, the main actions for those devices are available

directly from the Belkin Router Monitor menu.

Memory Safe

Memory Safe allows you to set up a routine backup of your

files to a hard drive or flash drive attached to your Router.

Memory Safe is found in the Belkin Router Manager icon

displayed in your system tray (Windows) or menu bar (Mac).

Music Labeler

Belkin Music Labeler corrects metadata (track names, artist

names, track numbers, etc.) in your iTunes and Windows Media

libraries, making it easy to find the music you are looking for.

Music Labeler is found under the Belkin Router Manager icon

displayed in your system tray (Windows) or menu bar (Mac).

17

GETTING STARTED

Daily DJ

Belkin Daily DJ delivers personalized playlists from your

music collection, automatically, every day. It’s like having your

own personal DJ playing the songs that you want to hear. It

works great with iTunes and Windows Media Player. Daily

DJ is found under the Belkin Router Manager icon displayed

in your system tray (Windows) or menu bar (Mac).

18

GETTING STARTED

Additional Capabilities

Guest Access

You can allow guests to use your Internet connection without

joining your personal network. The network name and

password for the guest network is located on the network

information card found under the foot of your Router.

A person using your guest network will be able to join

without a password, but will be shown a login page when

they attempt to surf the Web. They will need to enter

the guest password into this page to continue.

Video Max

Video Max automatically prioritizes your network traffic to

ensure high-quality streaming video, VoIP calls, and games.

Music Mover

Music Mover sends music from a USB drive attached to your

Router to any UPnP (Universal Plug-and-Play) or DLNA-compatible

device on your network. These devices include certain gaming

systems, televisions, Blu-ray players, and cell phones.

18

GETTING TO KNOW YOUR ROUTER

A) Router Status Light

Your Router’s status is shown by the light on the front.

Off: The Router is not plugged into a power source.

Blinking Green: The Router is starting up.

Solid Green: The Router is connected to the Internet.

Blinking Amber: The Router can’t detect the modem. Either the

modem is off, is not plugged into the Router, or is unresponsive.

B) Wi-Fi Protected Setup (WPS) Light and Button

The WPS button on the front of your Router can be used to

help establish a secure connection between your Router and

other WPS-enabled Wi-Fi devices such as computers. To use

the WPS feature on your Router, see “Getting Started > Adding

Computers to Your Network > Using the WPS Button”.

The small light near the WPS button shows what is happening

while you are using WPS to establish a connection.

Off: Idle

Blinking Green: The Router is listening for a

WPS-enabled computer or other device.

Solid Green: The Router has made a secure

connection with the computer or other device.

Amber: A connection was not created.

Front Panel

(a)

(b)

19

GETTING TO KNOW YOUR ROUTER

A) Modem (WAN) Connector

Connect your modem to this

port using an Ethernet cable.

B) Wired (LAN) Connectors

Connect computers and other

wired network devices to these

ports using Ethernet cables.

C) USB Port

USB printers, disks, and other

USB devices plugged into this

port will be shared on your

network. Each USB port has a

light that indicates its status.

Off: No USB device is

connected or the attached

USB device is not in use.

Blinking: Please wait to

unplug the device until

the light turns off.

On: The USB device is

connected and being

shared on your network.

D) Reset Button

This button is used to restart

your Router in rare cases when it

functions incorrectly. Resetting

the Router will preserve your

settings. This button may also

be used to restore the factory

default settings. Please see

the Troubleshooting section

for more information.

E) Power Connector

Connect the included power

supply to this jack.

Back Panel

(a)

(b)

(c)

(d)

(e)

La pagina sta caricando ...

Belkin 8820ed00380_F7D4302_v1 Manuale utente

Questo manuale è adatto anche per

Belkin 8820ed00380_F7D4302_v1 Manuale utente

in altre lingue

Documenti correlati