Wolf ICBCT30EU Manuale utente

ELECTRIC COOKTOPS

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

3

ENGLISH 4

ESPÃNOL 22

FRANÇAIS 40

ITALIANO 58

DEUTSCH 76

As you follow these instruc tions, you will

notice WARNING and CAUTION symbols.

This blocked information is impor tant for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

5

WOLF ELECTRIC COOKTOPS

BEFORE YOU START

Proper installation is your responsibility.

Have a qualified technician install this

cooktop. You must also assure that electri-

cal installation is adequate and in compli-

ance with all local codes and ordinances.

Installations and repairs must be performed

by a qualified or licensed contractor or

electrician qualified or licensed by the state,

province, or region where this appliance is

being installed.

Make sure you have everything necessary

for correct installation. It is the responsibil-

ity of the installer to comply with the

installation clearances specified in this book

and on the product rating plate. The rating

plate is located on the underside of the

cooktop. Refer to the illustration below.

Electrical ground is required; see Electrical

Requirements on page 16.

This cooktop is intended for indoor use.

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

Save these Installation

Instructions for the local inspector’s use.

Please read the entire Installation Instruc-

tions prior to installation.

This installation must be completed by a

qualified technician.

Installer:

please retain these instructions

for local inspector’s reference, then leave

them with the homeowner.

Homeowner:

please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

IMPORTANT NOTE:

This appliance must be

installed in accordance local codes. The correct

voltage, frequency and amperage must be

supplied to the appliance from a dedicated,

grounded circuit which is protected by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

power ratings are listed on the product rating

plate.

Record the model and serial numbers before

installing the cooktop. Both numbers are on

the rating plate, located on the underside of

the cooktop. Refer to the illustration below.

RATING PLATE

INFORMATION

Model Number

Serial Number

Rating plate location

Location of rating

plate under cooktop

6

WOLF ELECTRIC COOKTOPS

LOCATION IN COUNTERTOP

A)

Minimum flat countertop surface. Must be

equal to or greater than cooktop width.

B)

Minimum 25 mm wide clearance from the

cooktop side edge to any combustible

surface up to 457 mm above the cooktop

(noted by shaded area).

OVERHEAD CABINET DIMENSIONS

C)

Minimum spacing between overhead side

cabinets must be greater than or equal to

the nominal width of the cooktop unit(s).

D)

Minimum 457 mm vertical distance from

the countertop to the bottom of side

cabinets within minimum side clearance.

E)

Minimum vertical distance between the

countertop and combustible materials

above the cooktop must be 762 mm.

F)

Minimum 25 mm from rear wall.

G)

Maximum 330 mm depth of overhead and

side cabinets directly above and within side

clearance.

Failure to locate the cooktop unit

without the proper clearances will result

in a fire hazard.

C

G

D

A

B

E

F

Minimum clearances for installation

SITE PREPARATION

IMPORTANT NOTE:

Installation of the Wolf

electric cooktop must meet the following

location requirements. All dimensions listed

are minimum requirements for safe operation.

Refer to the illustration below.

To eliminate the risk of burns or fire by

reaching over heated surface units,

cabinet storage space located above the

surface units should be avoided. If

cabinet storage is to be provided, the risk

can be reduced by installing a ventilation

hood that projects horizontally a

minimum of 127 mm beyond the bottom

cabinets.

7

INSTALLATION INSTRUCTIONS

INSTALLATION SPECIFICATIONS

The illustrations on pages 8–13 provide the

overall dimensions, installation specifications

and countertop cut-out for each of the Wolf

electric cooktop models.

These cooktops are designed to fit a standard

610 mm deep base cabinet with a 635 mm

deep countertop. Before making the counter-

top cut-out, verify that the cooktop will clear

the side walls of the base cabinet below.

Clearance is required for the terminal block

and conduit located at the right rear of the

cooktop. Refer to the illustration below for

dimensions.

FRAMED ELECTRIC COOKTOPS

For framed models, a minimum 146 mm

clearance is required between the countertop

and any combustible surface directly below

the cooktop.

Wolf framed electric cooktops are designed to

be installed in combination with other cooktop

units.

IMPORTANT NOTE:

When multiple cooktop

units are installed side by side, refer to the

countertop cut-out dimensions on page 11.

Wolf framed electric cooktops can accommo-

date a Wolf downdraft ventilation system.

Refer to installation instructions provided with

the downdraft for additional specifications.

56 mm

84 mm

24 mm

22 mm

32 mm

Terminal block dimensions

UNFRAMED ELECTRIC COOKTOPS

For unframed models, a minimum 159 mm

clearance is required between the countertop

and any combustible surface directly below

the cooktop.

IMPORTANT NOTE:

Unframed electric

cooktops are not designed to be installed in

combination with other cooktops.

IMPORTANT NOTE:

Unframed electric

cooktops cannot be installed with a downdraft

ventilation system.

For installation options of the unframed

electric cooktops, refer to Unframed Installa-

tions on pages 14–15.

8

E

102 mm

381 mm

381

mm

51 mm*

min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

340 mm

COOKTOP CUT-OUT

WIDTH

340 mm

COOKTOP CUT-OUT

WIDTH

838 mm

RECOMMENDED

CABINET WIDTH

457 mm

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm

recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out

to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up

to 457 mm above countertop.

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm

min

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

330 mm

max

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

FRONT OF COUNTERTOP

64 mm

min

489 mm

COOKTOP

CUT-OUT DEPTH

51**

mm

Overall Dimensions

Countertop Cut-Out

533 mm

OVERALL

DEPTH

381 mm

OVERALL WIDTH

127 mm

96 mm

TERMINAL BOX

MODEL ICBCT15E

Overall Width 381 mm

Overall Height 96 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance*

102 mm

Cut-Out Width 340 mm

Cut-Out Depth 489 mm

INSTALLATION SPECIFICATIONS – MODEL ICBCT15E

FRAMED MODEL ICBCT15E

The illustrations below provide installation

specifications for Model ICBCT15E.

If Model ICBCT15E is installed above cabinets,

the electrical placement is not critical. A

grounded electrical box should be located

within 1.2 m of the right rear of the cooktop.

For installation above an oven, unless you are

using cabinets deeper than 610 mm, it is

recommended that the electrical supply be

placed in the base cabinet to the right of the

oven.

WOLF

ELECTRIC COOKTOPS

IMPORTANT NOTE:

Do not block the cooling

fan located at the bottom of the cooktop.

*Minimum 146 mm clearance is required

between countertop and any combustible

surface directly below the cooktop.

For detailed terminal block dimensions,

refer to the illustration on page 7.

Dimensions may vary to

±

3 mm.

9

51 mm*min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

457 mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm

min

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

330 mm

max

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

610 mm min

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance

from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

102 mm

254

mm

89 mm

95 mm

min

762 mm OVEN OPENING

E

721 mm COOKTOP

CUT-OUT WIDTH

721 mm

COOKTOP CUT-OUT WIDTH

FRONT OF COUNTERTOP

64 mm

min

489 mm

COOKTOP

CUT-OUT DEPTH

838 mm

RECOMMENDED

CABINET WIDTH

762 mm min

51**

mm

Overall Dimensions

Countertop Cut-Out

533 mm

OVERALL

DEPTH

762 mm

OVERALL WIDTH

127 mm

96 mm

TERMINAL BOX

FRAMED MODEL ICBCT30E

The illustrations below provide installation

specifications for Model ICBCT30E.

For ease of installation, 838 mm cabinets

are recommended for installation of Model

ICBCT30E.

A Wolf 762 mm or 914 mm built-in single oven

may be installed below Model ICBCT30E. For

this installation, unless you are using cabinets

deeper than 610 mm, it is recommended that

the electrical supply be placed in the base

cabinet to the right of the oven.

Refer to installation instructions provided with

the built-in oven for additional specifications.

If Model ICBCT30E is installed above cabinets,

the electrical placement is not critical. A

grounded electrical box should be located

within 1.2 m of the right rear of the cooktop.

IMPORTANT NOTE:

Do not block the cooling

fan located at the bottom of the cooktop.

MODEL ICBCT30E

Overall Width 762 mm

Overall Height 96 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance*

102 mm

Cut-Out Width 721 mm

Cut-Out Depth 489 mm

INSTALLATION SPECIFICATIONS – MODEL ICBCT30E

INSTALLATION

INSTRUCTIONS

*Minimum 146 mm clearance is required

between countertop and any combustible

surface directly below the cooktop.

For detailed terminal block dimensions,

refer to the illustration on page 7.

Dimensions may vary to

±

3 mm.

10

WOLF ELECTRIC COOKTOPS

FRAMED MODEL ICBCT36E

The illustrations below provide installation

specifications for Model ICBCT36E.

For ease of installation, 991 mm cabinets

are recommended for installation of Model

ICBCT36E.

A Wolf 762 mm or 914 mm built-in single oven

may be installed below Model ICBCT36E. For

this installation, unless you are using cabinets

deeper than 610 mm, it is recommended that

the electrical supply be placed in the base

cabinet to the right of the oven.

Refer to installation instructions provided with

the built-in oven for additional specifications.

If Model ICBCT36E is installed above cabinets,

the electrical placement is not critical. A

grounded electrical box should be located

within 1.2 m of the right rear of the cooktop.

IMPORTANT NOTE:

Do not block the cooling

fan located at the bottom of the cooktop.

51 mm*min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

457 mm

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm

min

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

330 mm

max

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

610 mm min

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from

rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

873 mm

COOKTOP CUT-OUT WIDTH

873 mm

COOKTOP CUT-OUT WIDTH

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

102 mm

254

mm

89 mm

914 mm OVEN OPENING

95 mm

min

E

64 mm

min

FRONT OF COUNTERTOP

489 mm

COOKTOP

CUT-OUT DEPTH

51**

mm

Overall Dimensions

Countertop Cut-Out

533 mm

OVERALL

DEPTH

914 mm

OVERALL WIDTH

127 mm

96 mm

TERMINAL BOX

MODEL ICBCT36E

Overall Width 914 mm

Overall Height 96 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance*

102 mm

Cut-Out Width 873 mm

Cut-Out Depth 489 mm

INSTALLATION SPECIFICATIONS – MODEL ICBCT36E

*Minimum 146 mm clearance is required

between countertop and any combustible

surface directly below the cooktop.

For detailed terminal block dimensions,

refer to the illustration on page 7.

Dimensions may vary to

±

3 mm.

11

INSTALLATION INSTRUCTIONS

MULTIPLE COOKTOP

INSTALLATION

If the framed electric cooktop is to be used

with any combination of additional cooktop

units or modules with a filler strip, the cut-out

width is calculated by adding the correspon-

ding units' cut-out dimensions plus 32 mm for

each additional unit. Refer to the illustration

below.

IMPORTANT NOTE:

For Model ICBCT15E,

the cut-out width should be increased from

340 mm to 356 mm when installed with

multiple units.

IMPORTANT NOTE:

Unframed electric

cooktops Models ICBCT30EU and ICBCT36EU

are not designed to be installed in combination

with other cooktop units.

IMPORTANT NOTE:

When multiple units are

installed side by side, each unit must have its

own separate recommended electrical circuit.

64 mm

min

FRONT OF COUNTERTOP

489 mm

CUT-OUT

DEPTH

743 mm

TWO MODULES WIDTH

1130 mm – THREE MODULES WIDTH OR

1124 mm – 762 mm COOKTOP AND ONE MODULE

1518 mm – FOUR MODULES WIDTH OR

1511 mm – 762 mm COOKTOP AND TWO MODULES OR

1276 mm – 914 mm COOKTOP AND ONE MODULE

356 mm

CUT-OUT

WIDTH

Countertop cut-out dimensions for installation of multiple cooktops

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

our website,

wolfappliance.com.

When two or more modules are installed

together, an integrated module filler strip

(IFILLER/S) is recommended. If a 762 mm

downdraft ventilation system is also installed,

an integrated module support for downdraft

ventilation (ISUPPORT) is also required.

Contact your Wolf dealer for information on

these accessory components.

12

51 mm*min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

457 mm

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

762 mm OVEN OPENING

838 mm

RECOMMENDED

CABINET WIDTH

762 mm min

721 mm COOKTOP

CUT-OUT WIDTH

33 mm

RADIUS

62 mm

492 mm

COOKTOP

CUT-OUT DEPTH

11 mm RADIUS

765 mm**

RECESSED AREA FOR

FLUSH MOUNT INSTALLATION ONLY

FRONT OF COUNTERTOP

40 mm

537 mm**

RECESSED AREA

FOR FLUSH MOUNT

INSTALLATION ONLY

**Minimum dimension, but may be exceeded by up to 3 mm.

RECESSED AREA FOR

FLUSH MOUNT INSTALLATION ONLY

8 mm

22 mm

max

COUNTERTOP

PROFILE

330 mm

max

610 mm min

102 mm min

SEE COUNTERTOP

CUT-OUT BELOW

SEE COUNTERTOP

CUT-OUT BELOW

*Minimum clearance from both side edges and back edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

51 mm*

E

254

mm

102 mm

min

TO OVEN

OPENING

89 mm

114 mm

Overall Dimensions

Countertop Cut-Out

533 mm

OVERALL

DEPTH

762 mm

OVERALL WIDTH

140 mm

108 mm

TERMINAL BOX

UNFRAMED MODEL ICBCT30EU

The illustrations below provide installation

specifications for Model ICBCT30EU.

For ease of installation, 838 mm cabinets are

recommended for installation of Model

ICBCT30EU.

A Wolf 762 mm built-in single oven may be

installed below Model ICBCT30EU. For this

installation, unless you are using cabinets

deeper than 610 mm, it is recommended that

the electrical supply be placed in the base

cabinet to the right of the oven. Refer to instal-

lation instructions provided with the built-in

oven for additional specifications.

If Model ICBCT30EU is installed above

cabinets, electrical placement is not critical. A

grounded electrical box should be located

within 1.2 m of the right rear of the cooktop.

For Model ICBCT30EU installation options,

refer to Unframed Installations on pages

14–15.

IMPORTANT NOTE:

For flush mount applica-

tions, it is recommended to measure the

cooktop glass before cutting the countertop to

ensure a proper fit. Small variances may exist

between the template and the cooktop.

MODEL ICBCT30EU

Overall Width 762 mm

Overall Height 108 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance*

114 mm

Cut-Out Width 721 mm

Cut-Out Depth 492 mm

INSTALLATION SPECIFICATIONS – MODEL ICBCT30EU

WOLF ELECTRIC COOKTOPS

*Minimum 159 mm clearance is required

between countertop and any combustible

surface directly below the cooktop.

For detailed terminal block dimensions,

refer to the illustration on page 7.

Dimensions may vary to

±

3 mm.

13

INSTALLATION INSTRUCTIONS

UNFRAMED MODEL ICBCT36EU

The illustrations below provide installation

specifications for Model ICBCT36EU.

For ease of installation, 991 mm cabinets are

recommended for installation of Model

ICBCT36EU.

A Wolf 914 mm built-in single oven may be

installed below Model ICBCT36EU. For this

installation, unless you are using cabinets

deeper than 610 mm, it is recommended that

the electrical supply be placed in the base

cabinet to the right of the oven. Refer to instal-

lation instructions provided with the built-in

oven for additional specifications.

If Model ICBCT36EU is installed above

cabinets, electrical placement is not critical.

A grounded electrical box should be located

within 1.2 m of the right rear of the cooktop.

For Model ICBCT36EU installation options,

refer to Unframed Installations on pages

14–15.

IMPORTANT NOTE:

For flush mount applica-

tions, it is recommended to measure the

cooktop glass before cutting the countertop to

ensure a proper fit. Small variances may exist

between the template and the cooktop.

51 mm*min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

457 mm

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

*Minimum clearance from both side edges and back edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

991 mm

RECOMMENDED CABINET WIDTH

914 mm min

914 mm OVEN OPENING

918 mm**

RECESSED AREA FOR

FLUSH MOUNT INSTALLATION ONLY

873 mm

COOKTOP CUT-OUT WIDTH

33 mm

RADIUS

FRONT OF COUNTERTOP

62 mm

492 mm

COOKTOP

CUT-OUT DEPTH

40 mm

537 mm**

RECESSED AREA

FOR FLUSH MOUNT

INSTALLATION ONLY

11 mm RADIUS

**Minimum dimension, but may be exceeded by up to 3 mm.

RECESSED AREA FOR

FLUSH MOUNT INSTALLATION ONLY

8 mm

22 mm

max

COUNTERTOP

PROFILE

SEE COUNTERTOP

CUT-OUT BELOW

330 mm

max

610 mm min

SEE COUNTERTOP

CUT-OUT BELOW

51 mm*

102 mm

min

E

254

mm

102 mm

min

TO OVEN

OPENING

89 mm

114 mm

Overall Dimensions

Countertop Cut-Out

533 mm

OVERALL

DEPTH

914 mm

OVERALL WIDTH

140 mm

108 mm

TERMINAL BOX

MODEL ICBCT36EU

Overall Width 914 mm

Overall Height 108 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance*

114 mm

Cut-Out Width 873 mm

Cut-Out Depth 492 mm

INSTALLATION SPECIFICATIONS – MODEL ICBCT36EU

*Minimum 159 mm clearance is required

between countertop and any combustible

surface directly below the cooktop.

For detailed terminal block dimensions,

refer to the illustration on page 7.

Dimensions may vary to

±

3 mm.

14

WOLF ELECTRIC COOKTOPS

UNFRAMED INSTALLATIONS

MODELS ICBCT30EU AND ICBCT36EU

Unframed electric cooktop Models ICBCT30EU

and ICBCT36EU can be mounted flush with the

top of the countertop or as a frameless instal-

lation with the glass mounted on top of the

countertop surface.

IMPORTANT NOTE:

The materials required

for a flush mount installation are provided with

the unframed Models ICBCT30EU and

ICBCT36EU. Refer to the instructions provided

with the unframed cooktop installation kit

(#811358) for additional specifications.

FLUSH MOUNT INSTALLATION

There are two options for a flush mount

installation of the unframed electric cooktop;

Option 1 and Option 2.

OPTION 1:

For this flush mount installation, a

recessed area surrounding the standard coun-

tertop cut-out is required. Fabrication of the

recessed area must take place before the final

countertop installation. A template of the coun-

tertop cut-out is provided with the unframed

cooktop for fabrication purposes.

IMPORTANT NOTE:

This fabrication method is

not recommended for molded backsplash style

countertops (triple cove).

For countertop cut-out dimensions, refer to

the Installation Specifications illustration on

page 12 for Model ICBCT30EU and page 13 for

Model ICBCT36EU.

In order to rout the required recessed area for

this flush mount installation, a second

template must be made from 13 mm plywood.

The template will be used as a guide for a top

bearing router bit.

Make the wood template wide enough so that

clamps used to hold this template to the coun-

tertop do not interfere with the router base.

The cut-out dimension of the wood template

should match the outer perimeter of the

template supplied with the cooktop.

Center the wood template over the existing

cut-out in the countertop and clamp. It may be

helpful to use medium-strength double-sided

tape to adhere the template to the countertop;

this will keep the template from shifting during

the routing operation. Make sure that the

adhesive can be easily removed by testing it

on a scrap piece of the countertop. Using a top

bearing router bit with the wood template as a

guide, rout out a 8 mm deep recessed area in

the countertop cut-out.

Flush mount installations are intended

for granite, solid surface or stone coun-

tertop surfaces only. Failure to use high

heat resistant surface will result in coun-

tertop damage if hot cooking utensils are

accidentally moved off the cooking

surface.

15

INSTALLATION INSTRUCTIONS

FRAMELESS INSTALLATION

Unframed electric cooktop Models ICBCT30EU

and ICBCT36EU can be installed as a frameless

application, with the glass mounted on top of

the countertop surface. For countertop cut-out

dimensions, refer to the Installation Specifica-

tions illustration on page 12 for Model

ICBCT30EU and page 13 for Model ICBCT36EU.

UNFRAMED INSTALLATIONS

FLUSH MOUNT INSTALLATION

OPTION 2:

For this flush mount installation,

the countertop cut-out will be the same size as

the outer edge of the glass top. It is recom-

mended that cooktop itself be used as the

template for the cut-out. Turn the cooktop over

and mark the opening using the glass top as a

template.

It will be necessary to attach L-shaped brackets

or cleats to the inner perimeter of the cut-out

to support the cooktop. The top edge of the

bracket can be no wider than 22 mm and will

be attached 8 mm below the surface of the

countertop. Refer to the illustration below.

Attachment of the brackets is up to the

installer's discretion, wherever enough coun-

tertop material is present.

For additional support in the cut-out area,

adhere scrap countertop material to the

bottom side of the countertop. Consult your

countertop supplier for the proper methods of

attachment.

22 mm

8 mm

L-Shaped

Brackets

Flush mount installation brackets

16

WOLF ELECTRIC COOKTOPS

ELECTRICAL REQUIREMENTS

REQUIRED POWER SUPPLY

Model ICBCT15E

220-240 V AC, 50/60 Hz

Models ICBCT30E and ICBCT30EU

220-240 V AC, 50/60 Hz

Models ICBCT36E and ICBCT36EU

220-240 V AC, 50/60 Hz

MAXIMUM CONNECTED LOAD

Model ICBCT15E

3.7 kW

Models ICBCT30E and ICBCT30EU

8.1 kW

Models ICBCT36E and ICBCT36EU

10.5 kW

Verify that power is disconnected from

the electrical box before proceeding.

This appliance must be installed in accordance

with local codes. The correct voltage,

frequency and amperage must be supplied to

the appliance from a dedicated, grounded

circuit which is protected by a properly sized

circuit breaker or time delay fuse. The proper

voltage, frequency and power ratings are listed

on the product rating plate, located on the

underside of the cooktop. Refer to the illustra-

tion on page 5 for location of the rating plate.

17

INSTALLATION INSTRUCTIONS

ELECTRICAL REQUIREMENTS

A properly rated cord should be attached to

the power supply of the electric cooktop as

shown in the illustration below. Open the

power box to expose the screws with corre-

sponding numbers. Loosen the 1, 5, and

ground screws. Run the cord through the

circular hole and into the supply box. Attach

the Neutral wire to the number 1 position.

Attach the line wire to the number 5 position

and attach the ground wire to the correspon-

ding ground screw. After tightening the

screws, tighten the cord strain relief then close

the cover to the power supply box without

pinching any of the wires.

The complete appliance must be properly

grounded at all times when electrical

power is applied.

Do not ground the appliance with the

neutral (white) house supply wire. A

separate ground wire must be utilized.

If aluminum house supply wiring is

utilized, splice the appliance copper wire

to the aluminum house wiring using

special connectors designed and agency

certified for joining copper and

aluminum. Follow the connector manu-

facturer's recommended procedure care-

fully. Improper connection can result in a

fire hazard!

IMPORTANT

NOTE

This appliance

must be installed

in accordance

with local codes.

GROUND

L1

N

Wiring diagram

18

COOKTOP INSTALLATION

Attach the foam strip to the underside of the

cooktop frame. Refer to the illustration below.

IMPORTANT NOTE:

For frameless installa-

tions, adhere the foam strip to the outer edge

of the glass, not the support frame.

IMPORTANT NOTE:

The materials required

for a flush mount installation are provided with

the unframed Models ICBCT30EU and

ICBCT36EU. Refer to the instructions provided

with the unframed cooktop installation kit

(#811358).

Gently lower the unit into the cut-out area in

the countertop and center. Check that the front

edge of cooktop is parallel to the front edge of

the countertop. Check that all required clear-

ances are met.

Attach the brackets to the bottom of the unit,

as shown in the illustration below. Install the

clamping screws into the bracket and tighten

until the screws contact the underside of the

countertop.

Do not overtighten the screws.

IMPORTANT NOTE:

Do not seal the cooktop

to the countertop. It must be removed if

service is necessary.

COOKTOP

FOAM

STRIP

COOKTOP

COUNTERTOP

BRACKET

SCREWS

BRACKET

102 mm

CLAMPING

SCREW

Foam strip Installation brackets

If the ceramic glass top of the cooktop is

broken, turn off power to the unit. Do

not operate until glass has been replaced

by a Wolf authorized service center.

WOLF ELECTRIC COOKTOPS

19

BEFORE OPERATING THE COOKTOP

Clean the ceramic glass surface carefully using

the Cooktop Cleaning Crème provided with the

cooktop. Remove all cleaning residue.

Read the entire Wolf Electric Cooktops

Use & Care Information included with the

cooktop.

COOKTOP

REMOVAL

IMPORTANT NOTE:

This procedure should

only be performed by a Wolf authorized

service center.

If it is necessary to remove the cooktop for

cleaning or service, disconnect the electrical

supply. Remove the mounting brackets on the

right and left side of the unit and remove the

cooktop. Reinstall in the reverse order.

IMPORTANT NOTE:

For flush mount installa-

tions, use a razor blade to carefully cut around

the RTV perimeter seal. A new RTV installation

kit (#811358) will be required to reinstall the

cooktop. This kit is available through your

Wolf dealer. To obtain local dealer information,

visit our website, wolfappliance.com.

INSTALLATION INSTRUCTIONS

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

our website,

wolfappliance.com.

20

This cooktop must be repaired only by a

Wolf authorized service center. The unit

must be disconnected from power prior

to service.

WOLF ELECTRIC COOKTOPS

TROUBLESHOOTING

IF COOKTOP DOES NOT OPERATE

IMPORTANT NOTE:

If the electric cooktop

does not operate properly, follow these

troubleshooting steps:

Verify that power is being supplied to the

cooktop.

Check electrical connections to ensure that

the installation has been completed

correctly.

Follow troubleshooting procedures as

described in the Wolf Electric Cooktops

Use & Care Information.

If the cooktop still does not work, contact

a Wolf authorized service center. Do not

attempt to repair the cooktop yourself.

Wolf is not responsible for service required

to correct a faulty installation.

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

our website,

wolfappliance.com.

La pagina sta caricando ...

Wolf ICBCT30EU Manuale utente

Wolf ICBCT30EU Manuale utente

in altre lingue

Documenti correlati

Altri documenti