Spektrum DX8 Manuale del proprietario

Categoria
Giocattoli telecomandati
Tipo
Manuale del proprietario
SD Logo is a
trademark of
SD-3C, LLC
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di istruzioni
Manual de Instrucciones
The Leader in Spread Spectrum Technology
SD Logo is a
trademark of
SD-3C, LLC
Instruction Manual
8-Channel DSM Radio System with
Integrated Telemetry for Airplanes and
Helicopters
The Leader in Spread Spectrum Technology
EN
4

NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc.
For up to date product literature, visit http://www.horizonhobby.com/ProdInfo/Files/SPM8800-manual.pdf.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage
AND a little or no possibility of injury
CAUTION: Procedures, which if not properly followed, create the probability of physical property
damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage,
collateral damage, and serious injury OR create a high probability of supercial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product, personal
property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and
requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by children without direct
adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way
without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance.
It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.

Thank You for purchasing a genuine Spektrum Product. Always purchase products from a Horizon Hobby, Inc. authorized
dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, Inc. disclaims all support and warranty with
regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with
DSM2 or Spektrum.

Visit www.spektrumrc.com/registration today to register your product.
EN
5

Spektrum’s DX8 with Integrated Telemetry ......................................................6
Included Items ..................................................................................................6
System Features ...............................................................................................6
Charging Your Transmitter ................................................................................7
NiMH/LiPo Battery Support ..............................................................................7
Battery and Charging Precautions and Warnings .............................................7
Transmitter Identification Mode 2 .....................................................................8
Transmitter Identification Mode 1 .....................................................................9
Key Input and Display Functions ....................................................................10
Digital Trims ...................................................................................................10
Inactivity Warnings .........................................................................................10
No RF Output Warning ...................................................................................10
Battery Alarm and Display ..............................................................................10
Programmable Alarms ....................................................................................10
AR8000 Receiver ............................................................................................10
Receiver Installation........................................................................................11
Binding ...........................................................................................................11
Failsafe ...........................................................................................................12
SmartSafe .......................................................................................................12
Hold Last Command Failsafe .........................................................................12
Preset Failsafe ................................................................................................12
Range Testing .................................................................................................13
System Setup ...........................................................................................13
Model Select ...................................................................................................14
Model Type .....................................................................................................14
Model Name ...................................................................................................15
Wing Type .......................................................................................................15
Switch Select (Air) ..........................................................................................15
Swash Type .....................................................................................................15
Switch Select (Heli) ........................................................................................16
F-Mode Setup.................................................................................................16
Trim Step ........................................................................................................16
Model Reset ....................................................................................................17
Model Copy ....................................................................................................17
Warnings ........................................................................................................18
Telemetry ........................................................................................................18
Frame Rate ......................................................................................................20
Trainer .............................................................................................................20
System Settings ..............................................................................................20
Transfer SD Card ............................................................................................21
 ........................................................................................22
Servo Setup ....................................................................................................22
D/R and Exponential .......................................................................................23
Differential ......................................................................................................24
Throttle Cut .....................................................................................................25
Throttle Curve (Air) .........................................................................................25
Throttle Curve (Heli) .......................................................................................26
Flap System ....................................................................................................26
Swashplate .....................................................................................................27
Governor .........................................................................................................28
Pitch Curve .....................................................................................................28
Mixing (Air) ....................................................................................................29
Aileron to Rudder Mix ....................................................................................29
Programmable Mixes (Air) .............................................................................29
Tail Curve for Non-Heading Hold Gyro Use Only ...........................................30
Mixing (Heli) ..................................................................................................31
Gyro ................................................................................................................33
Timer ..............................................................................................................33
Monitor ...........................................................................................................35
Troubleshooting Guide ...................................................................................35
General Information ........................................................................................36
Servo Precautions
General Notes
Safety Do’s and Don’ts for Pilots
Federal Aviation Administration.................................................................36
Purpose
Background
Operating Standards
Information Provided by
Daily Flight Checks
Warranty and Repair Policy ............................................................................37
Warranty Period
1-Year Limited Warranty
Damage Limits
Safety Precautions
Warranty Services
Questions, Assistance, and Repairs
Inspection or Repairs
Warranty Inspection and Repairs ...............................................................38
Non-Warranty Repairs
FCC Information .............................................................................................38
Antenna Separation Distance ..........................................................................38
Compliance Information for the European Union ...........................................39
Declaration of Conformity...............................................................................39
Instructions for the Disposal of WEEE ............................................................39
 ......................................................................................................39
Mode Changes ..........................................................................................39
Mechanical Conversion .............................................................................39
Programming Conversion .........................................................................40
Adjustable Stick Tension ...........................................................................41
Advanced Range Testing ............................................................................41
Using a Flight Log—Optional ...................................................................42

EN
6



The DX8 is Spektrum’s first aircraft system that incorporates integrated telemetry.
The transmitter’s screen displays real-time telemetry including receiver battery
voltage, flight log data and signal quality. External sensors allow rpm, external
voltage and temperature to be displayed on screen in real time. Alarms can
be programmed to warn of low battery, over temperature, exceeded rpm and
diminished RF signal strength.
The DX8 offers sophisticated programming to meet the demands of even the
most experienced airplane and helicopter pilots. An easy-to-use rolling selector
combined with intuitive software makes setting up models quick and easy. The
DX8 is SD-card compatible allowing an infinite number of models to be stored
and transferred. Plus firmware updates can be downloaded from the
SPEKTRUMRC.com website providing the user with the latest software upgrades.

Integrated Telemetry•
Quad Bearing Gimbals•
High Speed 11ms frame rate•
2048 resolution•
Telemetry warning system•
Sophisticated Airplane and Helicopter programming•
SD Card compatible•

Note: The DX8 is compatible with all current Spektrum DSM2 aircraft
receivers.
 When using the DX8 with parkflyer receivers (the
AR6100 and AR6110), it’s imperative that these receivers only be flown
in parkflyer-type aircraft (small electric airplanes or mini and micro
helicopters). Flying receivers designed for parkflyers in larger aircraft
could cause loss of connection.
Note: The DX8 is NOT compatible with the original DSM AR600 receiver.

DX8 transmitter
AR8000 8-channel receiver
Power supply w/ adaptors
Neckstrap
SD card
Bind Plug
TM1000 telemetry module
Voltage sensor
Temperature sensor
Data lead
Telemetry Y-Harness
Decal sheet
DX8 instruction manual
Programming Guide
2.0mm L hex wrench
Telemetry module (TM1000)
Voltage Sensor
Temperature Sensor
2.5” Telemetry
Data Lead
2.5” Telemetry
Y-harness
16MB SD Card
Male/female bind plug
12V DC Power Supply
Neckstrap
Decal sheet
EN
7


The DX8 features a built-in multi-chemistry charger designed to charge 4-cell
NiMH and 2-cell LiPo batteries at a charge rate of 200mAh. The charge jack on
the right side of the transmitter is non-polarity-critical, allowing you to use any
type of 12-volt supply to charge the battery regardless of connector polarity.
Using the included SPMB2000NMTX NiMH battery pack, you should plug the
included 12-volt AC to DC power supply in for 10 to 12 hours to fully charge
the battery.
   Never plug in a peak detection or fast charger into your
DX8 as this could damage the internal charge circuit. Use only a 12V DC
source.
With the transmitter power turned off, plug the included 12 volt power supply
into a wall outlet. Then plug the male charge plug into the charge jack. The blue
LED on the front of the transmitter will illuminate. When charging the optional
SPMB4000LPTX, a full charge can take up to 30hrs depending on the initial
charge state of the battery. When charging a LiPo, the blue light will turn off
when the charge cycle is complete.

The DX8 includes a rechargeable NiMH battery pack. A low battery alarm
sounds when the battery reaches 4.3 volts. Spektrum offers an optional 2-cell
LiPo battery pack (SPMB4000LPTX) for the DX8. LiPo batteries have a higher
operational voltage and when switching to a 2-cell LiPo battery in the transmitter,
it is important to change the low battery alarm to the LiPo setting to prevent
over-discharging the pack.

In the System Setting screen (see page 20 in your manual) rotate the roller to
select NEXT at the bottom right of the System setting screen. The following
screen appears.
Rotate the roller to highlight battery type.
Press the roller to access NiMH or LiPo. The low voltage cutoff will default to
the recommended voltage for the battery type selected. The voltage cutoff can be
adjusted from this screen, but normally the default cutoff of 6.4 volts for LiPo is
recommended.





property damage.
• Readallsafetyprecautionsandliteraturepriortouseofthisproduct.
•  allow minors to charge battery packs without adult supervision.
•  drop power supply or batteries.
•  attempt to charge damaged batteries
•  attempt to charge a battery pack containing different types of
batteries.
•  charge a battery if the cable has been pinched or shorted.
•  allow batteries or battery packs to come into contact with moisture
at any time.
•  charge batteries in extremely hot or cold places (recommended
between 50-80 degrees F) or place in direct sunlight.
•  disconnect the battery after charging, and let the charger cool
between charges.
•  inspect a new battery before charging.
•  terminate all processes and contact Horizon Hobby if the product
malfunctions.
•  keep batteries and charger away from any material that could be
affected by heat (such as ceramic and tile), as they can get hot.
•  end the charging process if the charger or battery becomes hot to
the touch or starts to change form (swell) during the charge process.
EN
8


Note: to change transmitter modes see page 39
Antenna
Rolling Selector
Aileron/Elevator
Stick
Elevator Trim
Aileron Trim
Power Switch
SD Card Slot
Throttle Trim
Throttle/Rudder
Stick
Handle
Rudder Trim
Elevator D/R
Clear Button
Back Button
Display Screen
Speaker
Mix/Hold
Aileron D/R
Rudder D/R
Aux 2/Governor
Charge Jack
R Trimmer
Aux 3 Knob
Trainer/Timer
Bind Button
Flap/Gyro
Gear
Flight Mode
L Trimmer

Do not attempt to use the antenna to bear
any weight, pick up the transmitter by the antenna or alter
the antenna in any way. If the transmitter antenna or related
components become damaged the output strength can be
severely impeded which could lead to a crash, injury, and
property damage.
EN
9


Antenna
Rolling Selector
Throttle/Aileron
Stick
Throttle Trim
Aileron Trim
Power Switch
SD Card Slot
Elevator Trim
Elevator/Rudder
Stick
Handle
Rudder Trim
Elevator D/R
Clear Button
Back Button
Display Screen
Speaker
Mix/Hold
Aileron D/R
Flight Mode
Aux 2/Governor
Charge Jack
R Trimmer
Aux 3 Knob
Trainer/Timer
Bind Button
Flap/Gyro
Gear
Rudder D/R
L Trimmer
EN
10


The DX8 utilizes a roller that can be rotated or pressed and two buttons, Back and
Clear that are used to access and program all the functions.
Direct Model Access- From the main screen, you can access the Model Select
screen (used to change models) by pressing the BACK and CLEAR buttons
simultaneously.

The DX8 2.4 features advanced digital trims. The Main screen displays the
graphic position for the trims. The Throttle Aileron, Elevator, and Rudder trim
levers, and when activated the right and left trimmers, feature an audible center
trim beep and a pause. You can adjust the amount of travel per each trim in the
Trim Step Function, located in System Setup Mode. See page 16 for more details.
Note: When the transmitter is turned off, the trims and left and right
trimmer values are stored in memory and recalled when the system is
turned back on.

The DX8 features an inactivity warning that warns if the transmitter is left on
preventing draining the batteries. If the transmitter is left on and no input is given
to the sticks or switches for 10 minutes, an alarm will sound and warning screen
appear. Moving any stick or switch will clear the alarm. Normal RF modulation
continues throughout the alarm maintaining the RF link.

The DX8 features a No RF output warning. If the 2.4GHz band is full, it’s possible
that the DX8 may not be able to find open channels when the transmitter is first
turned on. If the transmitter finds no open channels a warning screen appears and
will remain until the transmitter is able to find two open channels and transmit.

When the transmitter voltage drops below 4.3 volts, “Warning Low Battery” will
flash and an alarm sound. If you are flying when this occurs, land immediately.

The DX8 features programmable alarms that warn of a potential unsafe switch
or stick position when the transmitter is turned on. In Acro mode programmable
alarms include high throttle, gear and mid and land flap positions while in
helicopter mode warnings include high throttle, Stunt 1, Stunt 2, and Hold. If
any of these switches or throttle stick position is in an unsafe position when the
transmitter is turned on, an alarm will sound, the screen will display the offending
switch position and the transmitter will not transmit a signal. Moving the switch
or stick to the desired position will clear the warning and normal operation will
resume. See page 18 for details on programming warnings.

The AR8000 full range 8-channel receiver features DSM2
technology and
is compatible with all Spektrum
and JR
®
aircraft radios that support DSM2
technology including: JR12X, 11X, X9503, X9303, Spektrum DX8, DX7, DX7se,
DX6i, DX5e and Module Systems.
Note: The AR8000 receiver is not compatible with the Spektrum DX6
parkflyer transmitter.











Press the ROLLER to access screens or functions
Rotate the ROLLER to adjust values or to select options
Note: Pressing the ROLLER for more than three seconds will
return to the main screen.
Press the CLEAR button to return the highlighted value to its default setting
Press the BACK button to return to the previous screen
EN
11







Full range up to 8-channel aircraft including:
•Alltypesandsizesofglow,gasandelectricpoweredairplanes
•Alltypesandsizesofno-poweredgliders
•Alltypesandsizesofglow,gasandelectricpoweredhelicopters
Note: Not for use in airplanes that have full carbon fuselages. Not for
use in airplanes that have significant carbon or conductive structures. It is
recommended to use one of the carbon fuselage receivers. (SPMAR9300,
SPMAR6255).
















In gas and glow aircraft install the main receiver by wrapping it in protective foam
and fastening it in place using rubber bands or hook and loop strap.
In electric airplanes or helicopters, you can use thick double-sided foam tape to
fasten the main receiver in place.
Mount the remote in a slightly different location from the primary receiver. This
gives tremendous improvements in path diversity. Essentially, each receiver sees
a different RF environment and this is key to maintaining a solid RF link. This is
especially the case in aircraft with substantial conductive materials (e.g., larger
gas engines, carbon fiber, pipes etc), which can weaken the signal.
Using servo tape, mount the remote receiver keeping it at least 2 inches
away from the primary antenna. Ideally, you should position the antennas
perpendicular to each other. In airplanes, we recommend mounting the primary
receiver in the center of the fuselage on the servo tray and the remote receiver to
the side of the fuselage or in the turtle deck.

Do not use amplified Y-harnesses and servo extensions with Spektrum
equipment. Only use standard non-amplified Y-harnesses and servo extensions.
When converting existing models to Spektrum, replace all amplified Y-harnesses
and/or servo extensions with conventional non-amplified versions

Onboard power systems must provide adequate power, without interruption,
to the receiver even when the system is fully loaded (servos at maximum flight
loads). Inadequate power systems are a primary cause of in-flight failures. Some
components that affect the ability to properly deliver adequate power include:
the selected receiver battery pack (number of cells, capacity, cell type, state of
charge), switch harness, battery leads and, if used, the regulator and power bus.
The AR8000’s minimum operational voltage is 3.5-volts. Test the system per the
following guidelines to a minimum voltage of 4.8-volts during ground testing.
This will compensate for battery discharging or actual flight loads that are greater
than ground test loads.

1. When setting up large or complex aircraft with multiple high-torque
servos, use a current and voltmeter (HAN172). Plug the voltmeter in an
open channel port in the receiver, and with the system on, load the control
surfaces on your aircraft by applying pressure with your hand. Monitor the
current as you load control surfaces. The voltage should remain above 4.8
volts even when all servos are heavily loaded.
2. With the current meter inline with the receiver battery lead, load control
surfaces while monitoring the current. The maximum continuous
recommended current for a single heavy-duty servo/battery lead is 3 amps.
Short-duration current spikes of up to 5 amps are acceptable. If your system
draws more than these currents, you need to use multiple packs of the same
capacity with multiple switches and multiple leads plugged into the receiver.
3. If using a regulator, perform tests for a 5-minute period. A regulator may
provide adequate short-term power, but this tests its ability to maintain
voltage at significant power levels over time.
4. For really large aircraft or complex models, multiple battery packs with
multiple switch harnesses are necessary. No matter what power systems
you choose, always carry out test #1. Make sure the receiver is constantly
provided with 4.8 volts or more under all conditions.
When charging any brand of NiMH battery pack, make sure
the battery is fully charged. Due to the nature of peak charges and variations in
charging rates, heat development, and cell types–the capacity reading of a battery
charged on a fast peak charger may only reach 80% of its nominal value. Use a
charger that displays total charge capacity. Note the number of mAh put into a
discharged pack to verify the charge is at full capacity.

You must bind the receiver to the transmitter before the receiver will operate.
Binding teaches the receiver the specific code of the transmitter, so it will only
connect to that transmitter.
1. To bind an AR8000 to a DSM2 transmitter, insert the bind plug in the BATT/
BIND port on the receiver.
EN
12

Note: To bind an aircraft with an electronic speed controller that powers
the receiver through the throttle channel (ESC/BEC), insert the bind plug
into the BATT/BIND port in the receiver and the throttle lead into the throttle
(THRO) port. Proceed to Step #2.
2. Power the receiver. The LED on the receiver will be flashing, indicating the
receiver is ready to be bound to the transmitter.
3. Move the sticks and switches on the transmitter to the desired failsafe
positions (low throttle and neutral control positions).
4. Press and hold the trainer button while powering on transmitter.
5. The system will connect within a few seconds. Once connected, the LED on the
receiver will go solid indicating connection.
6. Remove the bind plug from the BATT/BND port on the receiver. Power off the
transmitter and store the bind plug in a convenient place.
 Remove the bind plug to prevent the system from entering bind mode
the next time the power is turned on.
7. After setting up your model, rebind the system so the true low throttle and
neutral control surface positions are set.

When you bind your transmitter, you are programming the receiver with failsafe
defaults. If connection is lost between the transmitter and receiver, the receiver
immediately operates in those preprogrammed default positions. Those positions
are failsafes. The AR8000 has three failsafes: SmartSafe Failsafe, Hold Last
Command Failsafe, and Preset Failsafe.
SmartSafe Failsafe
SmartSafe Failsafe is always active in both hold last command failsafe and in
preset failsafe. SmartSafe is a safety feature on the throttle channel only that offers
the following benefits:
• Preventselectricmotorsfromoperatingwhenthereceiveronlyisturnedon
(no signal present)
• Preventsthespeedcontrollerfromarminguntilthethrottleismovedtolow
throttle position after connection is made
• Shutsoffelectricmotorandreducesgas/glowenginestoidleifsignalislost
• Ifthrottleisatanypositionotherthanlow,theESCwon’tarm
• Ifconnectionislostinight:
-SmartSafe sets the throttle to the position it was in during the binding
process.

SmartSafe is automatically set when hold last command failsafe or Preset failsafe
is programmed or the system is bound. Note: It’s important to have the throttle
stick in the low position to store low throttle during binding
To Test
Confirm the failsafe setting is correct by turning off the transmitter. The throttle
should go to the preset low throttle position.
Make sure the aircraft is restrained on the ground. If failsafe is
not set, your aircraft might advance to mid or full throttle.
Hold Last Command
If you lose connection, all channels except for throttle channel hold last given
command and the aircraft continues on its path. So, if you were turning when
connection was lost, your aircraft would continue turning.

1. Leave the bind plug in the bind port through the entire binding process.
2. Remove bind plug only after receiver connects to transmitter
To Test
Confirm the failsafe settings are correct by turning off the transmitter. All channels
except for the throttle should hold the last command.
Make sure the aircraft is restrained on the ground. If failsafe
is not set, your aircraft might advance to mid or full throttle.
Preset Failsafe
If the signal is lost, all channels are driven to their failsafe position set during
binding.
Preset Failsafe is ideal for sailplanes, as spoliers can be deployed during loss of
signal, preventing a flyaway.

1. Insert the bind plug and power on the receiver.
2. When the receiver LEDs blink indicating bind mode, remove bind plug
before binding the transmitter to the receiver.
3. LED lights will continue to blink.
4. Move transmitter’s control sticks and switches to the desired Preset Failsafe
positions then turn it on in bind mode.
5. The system should connect in less than 15 seconds.
 Failsafe features vary according to receiver, so if using a receiver other
than the AR8000, consult your receiver’s instructions for the failsafes that apply.
Before flight, ALWAYS confirm your binding is good and failsafe is set. To do
this, make sure the system is connected, turn your transmitter off. Confirm that
low-throttle is active.
Make sure the aircraft is restrained on the ground. If failsafe is
not set, your aircraft might advance to mid or full throttle.
EN
13


The Range Test function reduces the power output. This allows for a range
test to confirm the RF link is operating correctly. Perform a range check at the
beginning of each flying session to confirm system operation.

With the transmitter on and the main or telemetry screen displayed, press the
roller. The Function list displays.
Rotate the roller to highlight Range Test then press the roller to access the Range
Test function.
With the Range Test screen displayed, push and hold the trainer button. The
screen displays Reduced Power. In this mode the RF output is reduced allowing
for an operational range test of your system.
If you let go of the trainer button, the transmitter will go back to Full Power.
Range Testing the DX8
1. With the model restrained on the ground, stand 30 paces
(approx. 90 feet/28 meters) away from the model.
2. Face the model with the transmitter in your normal flying position and place
the transmitter into Range Test mode (see above) and push the trainer button
reducing the power output.
3. Operate the controls. You should have total control of your model with the
transmitter in Range Test mode.
4. If control issues occur contact the appropriate Horizon Product Support
office for assistance.
5. If performing a range test while a telemetry module is active, the display will
show flight log data.

The DX8 organizes the programming screens in two separate categories:
System Setup Mode and Functions Mode. The System Setup Mode contains
programming that is generally used when initially setting up a model, and
seldom used at the field. System Setup functions includes Model Type, Model
Name, Wing Type, (Swashplate Type for Helis) Model Reset, etc. Note: No
radio transmission occurs when a System Setup screen is displayed to prevent
accidental servo operation. This protects linkages/servo gears from damage when
making programming changes. System Setup in Airplane and Heli Model type
includes the following screens.
 
Model Select page 14 Model Select page 14
Model Type page 14 Model Type page 14
Model Name page 15 Model Name page 15
Wing Type page 15 Swash Type page 15
Switch Select page 15 Switch Select page 16
Trim Step page 16 F-Mode Setup page 16
Model Reset page 17 Trim Step page 16
Model Copy page 17 Model Reset page 17
Warnings page 18 Model Copy page 17
Telemetry page 18 Warnings page 18
Frame Rate page 20 Telemetry page 18
Trainer page 20 Frame Rate page 20
System Settings page 20 Trainer page 20
Transfer SD Card page 21 System Settings page 20
Transfer SD Card page 21

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.

In the System Setup list rotate the roller to highlight the desired function then
press the roller to access. The selected function screen will appear.
30 paces (90 feet/28 meters)
EN
14


The Model Select function is used to change to a different model memory, typically
when switching from the current model. You can store up to 30 models in the DX8’s
model memory. You can access the model select function through the System
Setup mode or through Direct Model Access. Direct Model Access allows you to
access the model select function at any time the main screen or a telemetry screen
is displayed.

Press the Clear and Back buttons simultaneously to access the Model Select screen
To directly access the Model Select Screen any time from the Main Screen or the
Telemetry screen, press the Clear and Back buttons simultaneously. The Model
Select screen displays for 10 seconds. If no activity occurs, the screen returns to
the previous Main or Telemetry screen.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Highlight Model Select then press the roller to access the function.
The following screen appears. Rotate the roller to highlight the desired model
then press to select. The model name will display on the main screen.

The DX8 features ModelMatch technology that prevents operating a model using
the wrong model memory. This feature can prevent stripped servo gears, broken
linkages and even a crash due to attempting to operate a model using the wrong
memory.

Each individual model memory (30 in total) has its own embedded code
transferred to the receiver during the binding process. The receiver actually
learns the specific model memory selected during binding. When bound, it
operates only when that model memory is selected. If a different model memory
is selected, the receiver won’t connect. At any time you can reprogram the receiver
to operate with any other model memory by rebinding with the transmitter
programmed to the desired model.

Model Type programs the selected model memory to function in Helicopter or
Airplane programming. You should program Model Type first when setting up a
new model. Note: You can assign each model memory its own model type.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Type then press to access the function.
The following screen appears:
Rotate the roller to highlight the desired model type (Helicopter or Airplane) then
press the roller to select.
The following screen appears. Rotate the roller to highlight YES then press the
roller to accept the model type. Selecting NO will return you to the previous
screen.
Note: When you change model types (Heli to Acro or Acro to Heli) all
current programming in the selected model memory will reset to the
factory default settings. All previous settings will be lost.
You can return to the System Setting screen at anytime by
pressing the

button on the transmitter once.
To return to the Main screen press the  button on the
transmitter twice or press and hold the Roller for more than
three seconds.
EN
15


The Model Name function allows you to name a model using up to 10 characters.
This makes identifying and selecting models much easier. Naming a model is
normally done during initial setup. You can modify or change names at any time
without affecting other programming. Typical model names include Vibe 50 3D,
Extra 300, Blade 400, Sport 40 #1, etc. Note that upper case, lower case, numbers
and symbols are available.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Name then press to access the function.
The following screen appears:
Rotate the roller to highlight the desired character then press to accept.
Repeat the process until complete. The name will display on the main screen.
Pressing  will erase the current character.

Use the Wing Type function to program the wing and tail mix to match your
airplane. Eight wing types (Normal, elevon, dual aileron, 1 aileron and 1 flap,
flaperon, 1 aileron and 2 flaps, 2 ailerons and 1 flap, 2 ailerons and 2 flaps) and
five tail types (normal, V-Tail, dual elevator, dual rudder, dual rudder/ elevator) are
available. You must select the correct wing and tail type to match your airplane
before doing any other wing or tail related programming (e.g., Flaps, Travel
Adjust, Sub-Trim, etc.).

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Wing Type then press to access the function.
The following screen appears:
Rotate the roller to highlight Wing and press to access the function. Rotate the
roller to the desired wing mix. Press the roller to select.

Rotate the roller to highlight Tail then press.
Rotate the roller to access the desired tail type. Press the roller to select.

The Switch Select function allows the switches, knob and right and left trimmers
to be assigned to the gear, Aux1, Aux2 or Aux3 channels or inhibit.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight the desired switch, knob or trimmer then press the
roller to access.
Rotate the roller to select the desired channel or function you wish the switch,
knob or trimmer to operate. Press the roller to accept. Note that the channel or
function can only be assigned once.
Repeat to select all desired switch positions.

Use the Swash Type screen to program the swashplate mix to match your
helicopter swashplate type. Six swashplate types are available: Normal, 3-servo
120 CCPM, 3-servo 140 CCPM, 3-servo 90 CCPM, 3-servo 135 CCPM, and
2-servo 180 CCPM. Select the correct swashplate type to match the specific
helicopter before doing any other cyclic programming e.g., Pitch Curve, Travel
Adjust, Sub-Trim, etc.). If in doubt consult your helicopter’s manual for correct
swashplate mixing.
EN
16


Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Swash Type then press the roller to access the
function. The following screen appears:
Highlight the current swashplate type then rotate the roller to select the desired
swashplate mix. When the desired Swashplate mix is displayed press the roller
to select. In Systems Settings highlight User Name then press the roller to select
that function. Select the desired mode then press to accept.

The Switch Select function allows the switches, left knob and right and left
trimmers to be assigned to functions, channel or inhibit. In helicopter mode the
following options are available:

Inhibit Gear
Aux 2, Aux 3


Inhibit Gear
Aux 2 channel Aux 3 channel

Gear Aux 2 channel Aux 3 channel
Throttle Pitch

Can be assigned to one of the following:
Inhibit Hover Pitch
Hover throttle Gyro trim
Governor trim Gear Channel
Aux 2 channel Aux 3 channel

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight the desired switch, knob or trimmer then press.
Select the channel or function you wish to assign. See chart for options. Press the
roller to accept. Note that a channel or function can only be assigned once.
Repeat to select all desired switch positions.

The F-Mode setup screen is used to assign the switches that will be used for
Flight Mode and Hold. Flight Mode setup is defaulted to Flight Mode -flight
mode switch and Hold- Inhibited.
You can assign the flight mode and hold functions to any of 9 switches including:
Inhibit, Aileron D/R, Elevator D/R, Rudder D/R, Gyro switch, Flight Mode Switch,
Hold and the Governor switch.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight F-Mode Setup then press.
The following screen appears:
Highlight the Flight mode or Hold function then press to access that function.
Rotate the roller to select the desired switch.
TRIM STEP
The Trim Step function allows servo movement adjustment per click of trim. For
example you usually want a large trim step (8 to 10) for a new model. Each click
of trim will have a large amount of trim travel so you can quickly adjust an out-of-
trim model in flight. Later you can use a finer trim step (1-5) to adjust for precise
flight. The Trim Step function allows the trims to be common or independent in
each active flight mode. Many helicopter pilots use independent trims because
they are automatically active when a flight mode is activated. Important: The
trim step function has no effect on the overall trim travel, only the total number of
clicks available. If you select a 0 value in trim step, the trim is turned off.
EN
17


Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Trim Setup then press to access the function.
The following screen appears:
Highlight the desired Trim value then press the roller to access. Rotate the roller to
change to the desired trim value. Press to accept. Repeat to adjust all trim steps.

Rotate the roller to highlight Trim Type and press to access.
Select F-Mode (each flight mode has its own trims) or Common (trim are always
common regardless of flight mode).
Common Trim - When common trim is selected, trim values are common in all
flight modes.
F-Mode Trim - When F-Mode is selected, each flight mode including hold has its
own trims that are automatically active when that flight mode is selected.

Model Reset is typically used to clear the programming for a model you will no
longer be flying. Model Reset resets the programming for the selected model
to factory defaults. No other model memories will be affected. When a model’s
memory is reset all programming for that model is permanently deleted and
cannot be recovered.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Reset then press to access the function.
The following screen appears:
Verify that the model displayed on this screen is the model you wish to reset. If
not then see page 14 Model Select to access the desired model. Rotate the roller
to highlight Reset and then press to access the Confirm Reset screen.
Highlight YES If you’re sure you want to reset this model to factory default
settings, press the roller. The screen will return to the main screen.

The Model Copy function copies the currently selected model’s programming of
another model memory. Thirty model memories are available. Some of the more
common uses of the Model Copy function include:
•Movingtheorderofmodelsaroundinmodelmemorysotheycanbeorganized
by category, type, etc. Note: You will need to re-bind after moving models.
•Experimentingwiththeprogrammingforanaircraftwhilepreservingacopy
of the original setup. Note: If you want to use the model copy function to try
two slightly different setups with the same model you will need to rebind the
receiver each time you switch between model memories.
•Copyingtheprogrammingforanexistingmodelovertoanewmodelthat
is similar. Many pilots find this to be a good way to provide more accurate
baseline programming for the new model. For example Vibe 50 w/120CCPM
mixing, gyro and governor programming provides a good base programming
for any other nitro powered 120CCPM mixing helicopter. An Extra 300 with
dual aileron and elevator servos that is properly programmed with dual flap and
dual elevator mixing in Wing Type provides good foundational programming
for another aerobatic airplane with the same basic control system.
Important: The model memory you are copying to will be over-written by the
copied programming, permanently deleting any programming that may already exist.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Copy then press.
The following screen appears:
EN
18

Verify that the current model displayed on this screen is the model you wish to
copy. If not then see page 14 Model Select to access the desired model. Rotate
the roller to select the model memory (1 - 30) that the model will be copied to.
Select an unused model memory to copy to. When the desired model memory is
displayed, press the roller to access the Confirm Copy screen.
If you want to Copy this model to the selected model memory, press the roller
to copy. The screen returns to the main screen when the copy is complete. The
original model memory you just copied will still be selected.

The Warnings function programs an alarm to sound if specific switches or stick
positions are in an unsafe position when the transmitter is first turned on. In
helicopter model type default warnings include Throttle, Stunt 1, Stunt 2 and
Hold. In airplane model type these warnings include Throttle Low, Flaps, Gear,
Flight Mode 1 and Flight Mode 2. If you turn the transmitter on and any of these
switches or the throttle is not at the low position, the alarm will sound; the screen
will display the warning and no transmission will occur until the stick or switch is
in the correct position.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Warning then press.
The following screen appears:
Highlight the desired warning (Throttle, Stunt 1, Stunt 2 or Hold or Throttle, Flaps,
Gear, Flight Mode 1 and Flight Mode 2 for airplane model) then press the roller to
select. Now rotate the roller to inhibit or activate the selected warning.
To verify the warning is functioning turn the transmitter off, move the selected switch
or throttle in the offending position then turn the transmitter on. The alarm will
sound; the screen will display the specific warning and no modulation will occur.

Spektrum’s TM1000 telemetry module is compatible with all Spektrum and JR
receivers that have a Data (Flight Log) port including:

•AR7000 •AR9000
•AR7600 •AR9200
•AR8000 •AR9300
•AR12000 •AR7100
•AR7100R •AR9100
JR
•R921 •R1221
•R922 •R1222

Mount the TM1000 module near the receiver in a position that allows the 3-inch
data lead to extend from the receiver’s Data port to the Data port on the telemetry
module. You can use servo tape to secure the TM1000 module or wrap it in foam
with the receiver. Plug the Data lead into the TM1000 port marked DATA and plug
the other end of the lead into the receiver’s DATA port.
 Route and secure the antenna away from any metallic or conductive
materials to give the best range.
At this point the internal telemetry including the flight log data and the receiver
pack voltage is fully functional.
Before continuing, bind the system to the transmitter and confirm the telemetry
system is functioning.

1. Press and hold the bind button on the side of the TM1000 telemetry module.
2. While depressing the bind button, power the receiver. The main receiver,
all attached remote receivers and the TM1000 telemetry module will blink
indicating the system is in bind mode.
3. With the stick and switches in the desired failsafe positions (normally low
throttle and neutral sticks), put the transmitter into bind mode.
4. The main screen displays the receiver type. After several seconds, the
system connects and reverts to the main screen.
EN
19

5. From the main screen rotate the roller to access the telemetry screen and
verify the flight log data and receiver voltage displays.

The TM1000 includes a temperature and external voltage sensors. Optional RPM
sensors are available for Gas/Glow and electric brushless models to monitor RPM.
Temperature Sensor
To monitor the temperature of most any component, secure the sensor on the
object. It must come into contact with the surface to get an accurate temperature
reading. You can loop the temperature sensor around the engine’s cylinder head
to assist in tuning an engine. To monitor battery temperature, you can wrap the
sensor around the battery.
The mounting position of the sensor, especially on gas or glow engines, will
result in different temperature readings. So it’s important to experiment with
different positions.
Installation
Insert the temperature sensor connector into the port labeled TEMP/VOLT.
The temperature sensor is now active and the actual temperature displays
on screen.

External voltage telemetry is commonly used to monitor flight pack voltage or
you can monitor ignition batteries on gas engine equipped aircraft. You can set
warnings to prevent over-discharging batteries.
Installation
Plug the connector of the voltage sensor into the TEMP/VOLT port in the
Telemetry module.
Attach the opposite ends of the voltage sensor (stripped wires) to the
voltage source you wish to monitor.
Note the polarity (Red = + positive /Black = - Negative).
Typically, you can solder the wires to the battery connector. At this point the
External voltage displays on the telemetry screen.
Note: A Y-harness is provided if you want to use temperature and voltage
sensors simultaneously.

Two RPM sensors are available: SPMA9569 for nitro and gas engines,
SPMA9558 for brushless electric motors.
Engine RPM Sensor
The optional engine RPM sensor mounts inside the backplate of aircraft engines.
The sensor picks up the crankpin as the engine rotates giving accurate RPM.
Additionally, you can use this sensor as an RPM pickup on any rotating gear/
collar or shaft that has a steel setscrew or other magnetic metal by locating the
sensor within 5 mm of the rotating steel object.
Note: On some engines you may need to space the sensor further away
from the backplate. The sensor picks up the crankpin only; on some
engines if the sensor is too close, it will not distinguish the crankpin from
the crank weight.
Installation
Install the backplate sensor in the backplate.
Install the connector into the RPM port in the TM1000.
Testing
Turn the transmitter and receiver on and scroll to the RPM telemetry screen.
Rotate the engine rapidly and the RPM should register on the screen.
The RED LED on the TM1000 indicates the sensor is picking up properly.
You may need to adjust the sensor’s position to optimize the pickup. Move
the sensor closer or farther away until you have a reliable RPM pickup.
EN
20

Electric RPM Sensor
The optional electric RPM sensor is designed to be used with any brushless
motor. The sensor has two leads to attach to any two of the three motor wires.
This is typically done by soldering.
Installation
To install the electric RPM sensor using servo tape, attach the sensor in
a convenient place that allows the leads to reach the motor wires and the
TM1000 telemetry unit.
Solder the two sensor wires to any two motor leads.
Plug the sensor lead into the RPM port on the TM1000 telemetry module.
Testing
Turn the transmitter and receiver on and scroll to the RPM telemetry screen.
Run the motor and the RPM should register on the screen.
The RED LED on the TM1000 indicates the sensor is picking up properly.
 It is necessary to program a matching pole count in the telemetry
RPM screen to have accurate reading on screen. The motor’s pole count is
normally in the motor manufacturer’s instructions or on the manufacturer’s
website.

The Frame Rate function allows the selection of 11ms or 22ms frame rate. When
a 11ms frame rate receiver is used, the transmitter defaults to 11ms frame rate.
This fast frame rate is not compatable with some types of analog servos and the
Frame Rate screen allows the selection of a 22ms frame rate when a high frame
rate receiver is being used with analog servos.

Press and hold the roller while turning on the the transmitter. When system setup
appears on screen relese the roller. The DX8 is now in System Setup mode.
Rotate the roller to highlight Frame Rate then press.
The following screen appears:
Rotate the roller to highlight the frame rate then press. Now rotate the roller to
select 11ms or 22 ms frame rate.

The DX8 features a programmable trainer function with three trainer modes. The
transmitter assigns the trainer function to the trainer button. The function activates
when the switch is depressed and one of the three trainer modes is selected. The
three trainer Modes include:

In Inhibit you can use the transmitter as a slave only. However, the slave
transmitter must have the same programming as the master (e.g., servo
reversing, travel adjust, sub-trim, trims).

With Programmable Master you can program the transmitter to transfer any or
all channels when you activate the trainer switch. This is ideal for beginners
so the student learns control of individual channels (aileron only for example)
while the trainer maintains control of all other channels.
Note: When Programmable Master is selected for the master transmitter,
all settings for the slave transmitter (i.e. Servo reversing, wing type, Sub
trim, Travel Adjust, Mixing, etc.) must match the master’s transmitter
programming. If two DX8’s are being used simply copy and transfer the
model memory using the SD card from the master’s model to the slave.
The slave transmitter is then programmed to inhibit in the trainer screen.

When Pilot Link Master is selected the slave transmitter has control of the
stick function only (aileron, elevator rudder and throttle) while the master
maintains control of all other channels and functions including D/R and
switch positions. This is ideal for complex models as the master maintains
control of all secondary functions and controls all other channels.

Use Slave mode when flying with the DX8 as a slave when the master
radio has activated its Pilot Link. In this case, there is no need to match
programming between the slave and master transmitter.

Use the System Setting screen to establish the overall transmitter setting that will
apply to ALL model memories. These settings include: User Name, Contrast,
Mode, Region and Language. If you select Mode One, then Mode One will be
selected for all 30 model memories. Note: Even when models are imported from
an SD card the system settings in the transmitter will remain.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Highlight System Settings then press. The following screen appears:
Highlight the function you wish to change then press the roller to select.
User Name
User Name allows the identification of the owner to be programmed into the
transmitter. The user name appears during the startup process at the lower left
corner of the startup screen.
EN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208

Spektrum DX8 Manuale del proprietario

Categoria
Giocattoli telecomandati
Tipo
Manuale del proprietario