Eizo MS235WT Manuale del proprietario

Important

Please read PRECAUTIONS, this User’s Manual, and the Setup Guide

(separate volume) carefully to familiarize yourself with safe and

effective usage.

• Please refer to the Setup Guide for basic information ranging from

connection of the monitor to a PC to using the monitor.

• The latest User’s Manual is available for download from our web site:

http://www.eizoglobal.com

Instructions for Use

■User’s Manual

2

Location of Caution Statement

AVERTISSEMENT

WARNING

WARNUNG

This product has been adjusted specically for use in the region to which it was originally shipped. If operated

outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior

arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been

made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are

subject to change without notice.

3

Notice for this monitor

This product is suited to clinical review. It does not support the display of mammography images for diagnosis.

This product has been adjusted specically for use in the region to which it was originally shipped. If the product is

used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

· Power cords provided with the product

· Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to the

composition of the rubber. Check the desk surface before use.

It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after

the monitor power has been turned on or the monitor has recovered from the power saving mode, and then adjust the

monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a

stable display.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may

appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to

“Cleaning” (page 4)).

The screen may have defective pixels or a small number of light dots on the screen. This is due to the characteristics of

the panel itself, and is not a malfunction of the product.

The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact

your local EIZO representative.

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt

to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may

occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until

the dew condensation disappears, otherwise it may cause some damage to the monitor.

(Cautions for the Use of the Touch Panel)

• During touch operation

Be careful of the following points. Otherwise, damage may occur to the monitor.

- Do not strongly press, scratch, or poke the panel.

- Do not touch the panel with hard objects such as ballpoint pens or metals.

4Notice for this monitor

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,

and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

• Do not allow liquid to enter the clearance between the panel and the panel frame.

The stains on the cabinet and panel surface can be removed by using the provided cleaning cloth.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to

the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortably ............................. 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 7

1-1. Features ......................................................... 7

1-2. Controls and Functions ............................... 8

●Attaching the touch pen holder ....................... 9

1-3. EIZO LCD Utility Disk...................................10

●Disk contents and software overview ............10

1-4. Basic Operations and Functions ...............11

●Basic operation of the Setting menu .............. 11

●Functions ........................................................12

Chapter 2 Adjusting Screens .......................... 13

2-1. Compatible Resolutions .............................13

●Analog Input (D-Sub) .....................................13

●Digital Input (DVI-D) .......................................13

●Digital Input (DisplayPort) ..............................13

2-2. Setting the Resolution ................................14

●Windows 10 ....................................................14

●Windows 8.1 / Windows 7 ..............................14

●Windows XP ...................................................14

●Mac OS X .......................................................14

2-3. Adjusting Color ............................................15

●To select the display mode (CAL Switch

Mode) .............................................................15

●To perform advanced adjustments ................15

●Adjustable settings in each mode ..................16

●To adjust brightness .......................................16

●To adjust contrast ...........................................17

●To adjust color temperature ...........................17

●To adjust gamma ...........................................18

●To adjust the color saturation .........................18

●To adjust hue ..................................................19

●To set overdrive intensity................................19

●To adjust gain ................................................ 20

2-4. Screen Adjustment ......................................21

●Digital Signal Input .........................................21

●Analog Signal Input ........................................21

2-5. Screen Size Changing ................................ 25

●Screen Size Changing .................................. 25

●To adjust brightness of non-display area ...... 25

Chapter 3 Setting Monitor ............................... 26

3-1. Adjusting Volume........................................ 26

3-2. Selecting sound source while using the

DisplayPort signal input............................. 26

3-3. Enabling / Disabling DDC/CI

communication .......................................... 26

3-4. Locking Operation Buttons ....................... 27

3-5. Showing and hiding the EIZO logo ........... 27

3-6.

Changing Setting Menu Display Position

... 27

3-7. Setting Language ........................................ 28

3-8. Resetting the Monitor to the Default

Settings ........................................................ 29

●To reset the color adjustments ...................... 29

●To reset all adjustments to the default

settings .......................................................... 29

Chapter 4 Touch Panel Settings ..................... 30

4-1. Touch Panel Setting Method ..................... 30

4-2. Calibrating the Monitor ...............................31

4-3. ConguringTouchPanelOperation

Settings ........................................................ 32

Chapter 5 Power Saving Functions ................ 33

5-1. Setting Power Saving ................................. 33

●Monitor .......................................................... 33

●Audio Output ................................................. 34

5-2. Setting Power Indicator .............................. 34

5-3. Enabling / Disabling Automatic

Brightness Adjustment ............................. 34

5-4. Checking the power saving level .............. 35

5-5. Enabling / Disabling Auto Power-OFF ...... 35

Chapter 6 Troubleshooting .............................. 36

6-1. No picture .................................................... 36

6-2. Imaging problems (for both digital and

analog) ...........................................................37

6-3. Imaging problems (for analog only) ......... 38

6-4. Touch panel problems ................................ 39

6-5. Other problems ............................................41

Chapter 7 Reference ........................................ 42

7-1. Attaching the Optional Arm ....................... 42

7-2. Connecting Multiple PCs ........................... 44

●To switch among input signals ...................... 44

●To set input signal selection .......................... 45

7-3. Making Use of USB (Universal Serial

Bus) ............................................................... 46

●Required System Environment ..................... 46

●Connection Procedure (Setup of USB

Function) ........................................................ 46

7-4. Displaying Monitor Information .................47

7-5. Specications ............................................. 48

●Main Default Settings .................................... 49

●Outside Dimensions ...................................... 50

●Accessories ................................................... 50

6CONTENTS

7-6. Preset Timing ...............................................51

Chapter 8 Glossary .......................................... 52

Appendix .............................................................. 55

Trademark ............................................................... 55

License / Copyright ................................................ 55

Medical Standards ................................................. 56

FCC Declaration of Conformity ............................ 57

EMC Information .................................................... 58

LIMITED WARRANTY ..............................................61

Recycling Information ............................................70

7

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

• 23.0″ wide format LCD

• Supports a resolution of 1920 × 1080

• IPS panel with 89˚ horizontal and vertical viewing angles

• Touch Panel provided

- Projected capacitive technology

- Supported OS: Microsoft Windows 10 / Windows 8.1 / Windows 7 / Windows XP

- Supports the Windows Touch function (multi-touch) of Microsoft Windows 10 / Windows 8.1 / Windows

7.*1

*1 This product supports up to ve simultaneous touches (multi-touch support).

• 3 signal input terminals (DVI-D × 1, DisplayPort × 1, D-Sub × 1)

- Applicable to DisplayPort (applicable to 8 bit)*2

The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.

*2 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with

audio output (see “7-5. Specications” (page 48)).

• The CAL Switch function allows the user to select the display mode optimum to the displayed image.

- The Paper mode reproduces a printed paper effect on the monitor.

- Selectable DICOM (page 52) part 14 complied screen.

See “To select the display mode (CAL Switch Mode)” (page 15).

• Flattening of the bezel allows smooth touch operations.

• Small footprint achieved through low-prole and lightweight design

The monitor can be readily moved and its position adjusted.

• LaidBack Stand allows the monitor to be freely adjusted to a wide range of tilt angles.

Employs a free stop (non-step) system that allows exible angle adjustment to suit the environment or application.

The stand can be used at an angle suitable for reading books. In addition, the stand is designed to prevent screen

vibration during touch operation.

• Power saving function

Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving

function.

- 0 W power consumption when the main power is off

Equipped with main power switch.

When the monitor is not required, the power supply can be shut off using the main power switch.

- EcoView Optimizer 2

The monitor automatically adjusts the screen brightness according to the white level of the input signal. This

function can reduce the power consumption while maintaining the brightness specied by the input signal.

See “5-3. Enabling / Disabling Automatic Brightness Adjustment” (page 34).

• Displays HDCP (High-bandwidth Digital Protection) protected contents.

8Chapter 1 Introduction

1-2. Controls and Functions

7

8

10

12

13

14

15

16

1

2

3

4

5

9

6

11

17

Setting menu*1

1. button Switches input signals for display (page 44).

2. button Changes the CAL Switch mode (page 15).

3. , button*2

• Provides the menu selection as well as the adjustment and setting of a function.

• button: Displays the Brightness adjustment menu (page 16).

button: Displays the volume adjustment menu (page 26).

4. button Displays the Setting menu, determines an item on the menu screen, and saves values

adjusted (page 11).

5. button Turns the power on or off.

6. Power indicator

Indicates the monitor’s operation status.

Blue: Operating

Orange: Power saving mode

OFF: Main power / Power off

7. Main power switch Turns the main power on or off.

8. Power connector Connects the power cord.

9. Security lock slot Complies with Kensington’s MicroSaver security system.

10. Stand

(with cable holder) Used to adjust the angle of the monitor screen.

11. Speaker Outputs audio source.

12. Headphone jack Connects the headphones.

13. Stereo mini jack Connects the stereo mini jack cable.

14. Input signal connector Top: D-Sub mini15-pin connector / Center: DVI-D connector / Bottom: DisplayPort

connector

15. USB port (DOWN) Connects a peripheral USB device.

16. USB port (UP) Connects the USB cable for using the monitor as a touch panel monitor or for using the

USB Hub function (page 46).

17. Touch pen holder

attachment hole*3 Used to attach a touch pen holder.

*1 See “1-4. Basic Operations and Functions” (page 11) for how to use.

*2 In this User’s Manual, the button may be hereafter simply displayed as , and the button as .

*3 Refer to the next page regarding the attachment method.

9

Chapter 1 Introduction

●Attaching the touch pen holder

1. Align the touch pen holder over either the left or right attachment hole.

2.

Attach with the screw supplied with the touch pen.

1. 2.

10 Chapter 1 Introduction

1-3. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents

and the overview of the software programs.

●Disk contents and software overview

The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.txt le on

the disk for software startup procedures or le access procedures.

Item Overview

Screen adjustment pattern les Used when adjusting the image of analog signal input manually.

Touch panel driver Touch panel driver supplied by EIZO*1

TPOffset Software for adjusting the sensitivity of the touch panel*1

Use this software when touch operations are not registered or only

registered after pressing hard.

EIZO ScreenSlicer Software that divides a screen and lays out multiple windows efciently.*1

User’s Manual of this monitor (PDF le)

Readme.txt le

*1 Only for Windows. Refer to the corresponding User’s Manual on the CD-ROM for details on installation and use.

11

Chapter 1 Introduction

1-4. Basic Operations and Functions

●Basic operation of the Setting menu

1. Displaying the Setting menu

1. Press . The Setting menu appears.

2.

Adjusting / Setting

1. Choose a menu to adjust / set with , , and then press . The Sub menu appears.

2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears.

3. Adjust / set the selected item with , , and then press .

3.

Exiting

1. Choose “Return” from the Sub menu and press . The Setting menu appears.

2. Choose “Exit” from the Main menu and press . The Setting menu quits.

Note

• The Setting menu can also be exited by pressing twice quickly.

12 Chapter 1 Introduction

●Functions

The following table shows the Setting menu and setting items of each menu.

Main menu Setting Reference

Color*1 Brightness “2-3. Adjusting Color” (page 15)

Contrast

Temperature

Gamma

Advanced Settings Saturation

Hue

Overdrive

Gain

Color Reset “To reset the color adjustments” (page 29)

Screen Screen Size “Screen Size Changing” (page 25)

Smoothing “2-4. Screen Adjustment” (page 21)

Analog Adjustment*2 Auto Screen Adjust

Auto Range Adjust

Clock

Phase

Hor.Position

Ver.Position

Sound Source “3-2. Selecting sound source while using

the DisplayPort signal input” (page 26)

Power Save “Audio Output” (page 34)

PowerManager Power Save “5-1. Setting Power Saving” (page 33)

Eco Timer “5-5. Enabling / Disabling Auto Power-

OFF” (page 35)

Monitor Settings Input Signal “To set input signal selection” (page 45)

Power Indicator “5-2. Setting Power Indicator” (page 34)

Language “3-7. Setting Language” (page 28)

DDC/CI “3-3. Enabling / Disabling DDC/CI

communication” (page 26)

Border Intensity “To adjust brightness of non-display area”

(page 25)

Menu Settings Logo “3-5. Showing and hiding the EIZO logo”

(page 27)

Menu Position “3-6. Changing Setting Menu Display

Position” (page 27)

Reset “To reset all adjustments to the default

settings” (page 29)

EcoView EcoView Optimizer 2 “5-3. Enabling / Disabling Automatic

Brightness Adjustment” (page 34)

Information “7-4. Displaying Monitor Information”

(page 47)

*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode. The above table shows

the sub menus when the User1 or User2 mode is selected.

*2 These functions can be adjusted with analog input.

13

Chapter 2 Adjusting Screens

2-1. Compatible Resolutions

The monitor supports the following resolutions.

●Analog Input (D-Sub)

Resolution Applicable Signals Vertical Scan

Frequency Dot Clock

640 × 480 VGA, VESA ~75 Hz

148.5 MHz

(Max.)

720 × 400 VGA TEXT 70 Hz

800 × 600 VESA ~75 Hz

1024 × 768 VESA ~75 Hz

1280 × 720 CEA-861 60 Hz

1280 × 960 VESA 60 Hz

1280 × 1024 VESA ~75 Hz

1680 × 1050 VESA CVT, VESA CVT RB 60 Hz

1920 × 1080*1 CEA-861 60 Hz

●Digital Input (DVI-D)

Resolution Applicable Signals Vertical Scan

Frequency Dot Clock

640 × 480 VGA 60 Hz

148.5 MHz

(Max.)

720 × 400 VGA TEXT 70 Hz

800 × 600 VESA 60 Hz

1024 × 768 VESA 60 Hz

1280 × 720 CEA-861 60 Hz

1280 × 960 VESA 60 Hz

1280 × 1024 VESA 60 Hz

1680 × 1050 VESA CVT, VESA CVT RB 60 Hz

1920 × 1080*1 CEA-861 60 Hz

●Digital Input (DisplayPort)

Resolution Applicable Signals Vertical Scan

Frequency Dot Clock

640 × 480 VGA, CEA-861 60 Hz

148.5 MHz

(Max.)

720 × 400 VGA TEXT 70 Hz

720 × 480 (4:3) CEA-861 60 Hz

720 × 480 (16:9) CEA-861 60 Hz

800 × 600 VESA 60 Hz

1024 × 768 VESA 60 Hz

1280 × 720 CEA-861 60 Hz

1280 × 960 VESA 60 Hz

1280 × 1024 VESA 60 Hz

1680 × 1050 VESA CVT, VESA CVT RB 60 Hz

1920 × 1080*1 CEA-861 60 Hz

The graphics board should comply with the VESA standard and CEA-861 standard.

*1 Recommended resolution

14 Chapter 2 Adjusting Screens

2-2. Setting the Resolution

When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change the

resolution, follow the procedure below.

●Windows 10

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Display Settings”.

3. On the “Customize your display” dialog box, click “Advanced display settings”.

4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.

5. Click the “Apply” button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

●Windows 8.1 / Windows 7

1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.

2. Right-click the mouse anywhere on the desktop except for icons.

3. From the displayed menu, click “Screen resolution”.

4. On the “Screen Resolution” dialog box, select the monitor.

5. Click “Resolution” to select the desired resolution.

6. Click the “OK” button.

7. When a conrmation dialog box is displayed, click “Keep changes”.

●Windows XP

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Properties”.

3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution

for “Screen resolution” under “Display”.

4. Click the “OK” button to close the dialog box.

●Mac OS X

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.

4. Your selection will be reected immediately. When you are satised with the selected resolution, close the

window.

15

Chapter 2 Adjusting Screens

2-3. Adjusting Color

●To select the display mode (CAL Switch Mode)

This function allows easy selection of a desired mode according to monitor application.

Display Modes

Mode Purpose

User1 Select this to dene a desired set of parameter settings.

User2

sRGB Suitable for color matching with sRGB compatible peripherals.

Paper Produces a printed paper effect. Suitable for displaying images from media such as books

and documents.

DICOM Selected for the display in the DICOM mode.

The mode menu

appears.

Procedure

1. Press .

The mode menu appears at the bottom left of the screen.

2. The mode among the list is highlighted in turn each time is pressed.

You can switch the mode with or while the mode menu is displayed.

→User1←→User2←→sRGB←→Paper←→DICOM←

Note

• The Setting menu and the Mode menu cannot be displayed at the same time.

●To perform advanced adjustments

The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each

mode.

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the

monitor power has been turned on, and then adjust the monitor.

• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation automatically”

(page 24)).

• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics. Make

ne color adjustment visually when matching colors on multiple monitors.

16 Chapter 2 Adjusting Screens

●Adjustable settings in each mode

The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)

√: Adjustable -: Not adjustable

Function CAL Switch Mode

User1 User2 sRGB Paper DICOM

Brightness √√√√-

Contrast √ √ ---

Temperature √ √ -√-

Gamma √ √ ---

Advanced Settings Saturation √ √ ---

Hue √ √ ---

Overdrive √ √ ---

Gain √ √ ---

Color Reset √√√√-

●To adjust brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back

panel).

Adjustable range

0 to 100

Procedure

1. Press .

2. Use or for adjustment.

3. Press to exit.

Note

• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.

• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

• To adjust the screen brightness automatically and comfortably, see “5-3. Enabling / Disabling Automatic Brightness

Adjustment” (page 34).

17

Chapter 2 Adjusting Screens

●To adjust contrast

The brightness of the screen is adjusted by varying the video signal level.

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Contrast” in the “Color” menu, and press .

The “Contrast” menu appears.

3. Use or for adjustment.

4. Press to exit.

Note

• In the contrast of 50, every color gradation is displayed.

• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation

characteristics, prior to the contrast adjustment.

• Perform the contrast adjustment in the following cases.

- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)

●To adjust color temperature

Color temperature can be adjusted.

The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.

The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame

temperature. A gain preset value is set for each color temperature setting value.

Adjustable range

Off, 4000 K-10000 K (specied by every 500 K unit, including 9300 K)

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Temperature” in the “Color” menu, and press .

The “Temperature” menu appears.

3. Use or for adjustment.

4. Press to exit.

Note

• The value shown in “K” is available only as reference.

• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 20)).

• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).

• When gain is changed, the color temperature is changed to “Off”.

18 Chapter 2 Adjusting Screens

●To adjust gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the

variation rate is not proportional to the input signal. To keep the balance between the input signal and the

brightness of the monitor is called as “Gamma correction”.

Adjustable range

1.8, 2.0, 2.2

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Gamma” in the “Color” menu, and press .

The “Gamma” menu appears.

3. Use or for adjustment.

4. Press to exit.

Note

• If “Paper” is selected in the CAL Switch mode, the gamma value is displayed for “Paper”. The setting “Paper” is

specially meant to get the displayed image look like it is printed on paper.

●To adjust the color saturation

This function allows you to adjust color saturation.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Advanced Settings” in the “Color” menu, and press .

3. Choose “Saturation” in the “Advanced Settings” menu, and press .

The “Saturation” menu appears.

4. Use or for adjustment.

5. Press to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The minimum value (-50) changes the screen to monochrome.

19

Chapter 2 Adjusting Screens

●To adjust hue

This function allows you to adjust hue.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Advanced Settings” in the “Color” menu, and press .

3. Choose “Hue” in the “Advanced Settings” menu, and press .

The “Hue” menu appears.

4. Use or for adjustment.

5. Press to exit.

Attention

• Using this function may make some color gradations unavailable for display.

●To set overdrive intensity

This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags

by setting it to “Enhanced” when displaying animated images.

Adjustable range

Enhanced, Standard, Off

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Advanced Settings” in the “Color” menu, and press .

3. Choose “Overdrive” in the “Advanced Settings” menu, and press .

The “Overdrive” menu appears.

4. Use or for adjustment.

5. Press to exit.

Attention

• The overdrive function is disabled in the following cases:

- The vertical scan frequency of input signals is more than 70 Hz

- Select “Normal” during “Screen Size” (excluding the case that display resolution is 1920 × 1080).

- When the display resolution is set to 640 × 480, 720 × 480, 800 × 600 (only for 56.25 Hz vertical scan frequency)

20 Chapter 2 Adjusting Screens

●To adjust gain

The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of

“white” by adjusting gain.

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Advanced Settings” in the “Color” menu, and press .

3. Choose “Gain” in the “Advanced Settings” menu, and press .

The “Gain” menu appears.

4. Adjust gain with or for each of red, green, and blue.

5. Press to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to “Off”.

La pagina sta caricando ...

Eizo MS235WT Manuale del proprietario

Eizo MS235WT Manuale del proprietario

in altre lingue

Documenti correlati