Shindaiwa MTA-PS Manuale utente

Tipo
Manuale utente
1????
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE PER L'OPERATORE
MANUAL DE INSTRUCCIONES
MTA-PS
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS IN-
JURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LESRÈGLES DE
SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN
ISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE
FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE
IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA
DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
ADVERTENCIA
LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES
PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SU-
FRIR LESIONES GRAVES.
1Cover
OPERATOR'S MANUAL
ProSweep Attachment
MTA-PS
ENGLISH
(Original instructions)
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Important information
2Important informati on
Please ensure that you read the operator's manual before using your product.
Introduction
This product was designed and manufactured to provide long life and on-the-job dependability.Read and understand
this manual you found in the package. You will find it easy to use and full of helpful operating tips and SAFETY mes-
sages.
Users of the product
You should not use this product until you have read the operator's manual carefully and fully absorbed its content.
This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a
cold, tiredness or otherwise in poor physical condition, or children.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
About your operator's manual
This manual contains necessary information about the assembly, operation, and maintenance of your product. Please
read it carefully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,
and there may be a slight conversion error in some cases.
Loaning or assigning your product
When loaning the product described in this manual to another party, ensure that the person borrowing and working with
the product receives the operator's manual along with the product. If you assign your product to another party, please
enclose the operator's manual with the product when handing it over.
Enquiries
Please contact your dealer for requests regarding information about your product, the purchase of consumables, re-
pairs, and other such enquiries.
Notices
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
This product requires the assembly of some parts.
Please consult your dealer if anything is unclear or of concern.
IMPORTANT
This attachment is designed for use with the PAS-2620ES, M262S and DPAS-2600 power sources. Use of this attach-
ment with any other product will cause premature gear case failure and void the warranty.
WARNING
Read rules for safe operation and instructions carefully. YAMABIKO provides an Operator's Manual of your power
source. That manual and this manual must be read and understood for proper and safe operation, otherwise serious
personal injury may result.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-
placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo australia.com.au/
en_au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au ,Briggs &
Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.
3
Contents
For safe use of your product............................................................................................... 4
Warning notices............................................................................................................. 4
Other indicators ............................................................................................................. 4
Symbols.........................................................................................................................4
Location in which a safety decal is attached.................................................................. 5
Handling the product ..................................................................................................... 5
Description.......................................................................................................................... 9
Before you start ................................................................................................................10
Packing list .................................................................................................................. 10
Assembly ..................................................................................................................... 10
Operation .......................................................................................................................... 12
Maintenance and care ...................................................................................................... 13
Servicing guidelines..................................................................................................... 13
Maintenance and care ................................................................................................. 13
Storage ............................................................................................................................. 16
Specifications.................................................................................................................... 17
Declaration of conformity .................................................................................................. 19
UK Declaration of conformity ............................................................................................ 21
4
For safe use of your product
For safe use of yo ur product
Be careful to read this section before using your product.
The precautions described in this section contain important safety information. Please observe them carefully.
You must also read the precautions that appear in the body of the manual itself.
Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.
Warning notices
Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product
itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.
Other indicators
As well as warning notices, this manual uses the following explanatory symbols:
Symbols
In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what
each symbol means.
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual Keep bystanders away 15 m
Wear eyes, ears and head
protection
Beware of high-temperature
areas
Wear foot protection and
gloves Keep feet away from blade
Thrown objects Beware of electric shocks
5
For safe use of your product
Location in which a safety decal is attached
The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what
the decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.
Handling the product
General precautions
1. Safety decal (Part number 890160-25560)
WARNING
Operator's manual
Be careful to read the operator's manual properly before using your product in order to ensure correct
operation.
Failure to do so could lead to an accident or serious injury.
Do not use the product for anything other than its intended purpose
You must not use the product for any purpose other than those described in the operator's manual.
To do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be
covered by the manufacturer's warranty.
Do not use the product unless it has been checked and maintained
You must not use the product unless it has been checked and maintained. Always ensure that the product is checked
and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
6
For safe use of your product
Precautions for use
Loaning or assigning your product
When loaning your product to another party, ensure that the person borrowing the product receives the operator's
manual along with it.
If you assign your product to another party, please enclose the operator's manual with the product when handing it
over.
Failure to do so could lead to an accident or serious injury.
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure that you are pre-
pared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help, the injury could
worsen.
WARNING
WARNING
The area within a 15 m radius is a danger zone
The area within a 15 m radius of the product is a danger zone. Be careful to
observe the following precautions while working with the product.
Do not allow children and other people or pets to enter the danger zone.
If another person enters the danger zone, turn off the unit to stop.
When approaching the operator, signal to him by, for example, throwing
twigs from outside the danger zone, and then check that unit has been turn
off.
Any contact with the cutter blade could cause serious injury.
Avoid hot surfaces
During operation, the complete unit, especially the drive shaft housing and gear box may become very hot,
too hot to touch. Avoid contact during and immediately after operation.
You could burn yourself if you touch a high temperature component.
WARNING
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical condition
people who have not read the operator's manual
children
Failure to observe these instructions could lead to an accident.
Environment of use and operation
Do not use the product in places where there is no sure foothold, such as on steep slopes or after rainfall, as such
places are slippery and dangerous.
Do not operate the product at night or in dark places with poor visibility.
Do not work in odd positions or on ladders. Do not over reach.
A serious injury could result if you fall or slip, or fail to operate the product correctly.
For your own health and your safe and comfortable work, operate the machine within the air temperature range of -
5 oC to 40 oC.
Failure to observe these instructions could result in damage to your health.
7
For safe use of your product
Turn off the engine when moving around
When moving around in the situations described below, turn off the engine.
Moving to the place where you are working
Moving to another area while you are working
Leaving the place where you have been working
Failure to observe these precautions could cause burns or serious injury.
When transporting the product by car, empty the fuel tank, and secure the product firmly in place to prevent it from
moving around.
Travelling by car with fuel in the tank could lead to a fire.
Keep a firm grip
Hold the front and rear handles with both hands with thumbs and fingers tightly encircling the
handles.
Failure to observe these instructions could lead to an accident.
Vibration and cold
It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning, fol-
lowed by loss of colour and numbness in the fingers.
The following precautions are strongly recommended because the minimum exposure which might trigger the ailment
is unknown.
Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not
smoking.
Limit the number of hours of operation.
Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.
If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, consult
your physician before exposing yourself further to cold and vibration.
Failure to observe these instructions could result in damage to your health.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities may put
you at a high risk for developing a repetitive stress injury (RSI).
To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted position.
Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the
repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-
nosed, the more likely permanent nerve and muscle damage can be prevented.
Failure to observe these instructions could result in damage to your health.
Proper training
Do not permit operation without proper training and protective equipment.
Be thoroughly familiar with the controls and proper use of unit.
Know how to stop the unit and shut off the engine.
Never allow anyone to use the unit without proper instruction.
WARNING
8
For safe use of your product
Protective gear
WARNING
Wear protective gear
Always wear the following protective gear.
a Head protection (helmet): Protects the head
b Ear muffs or ear plugs: Protect the hearing
c Safety goggles: Protect the eyes
d Face shield: Protects the face
e Safety gloves: Protect the hands from cold and vibration
f Work clothes that fit (long sleeves, long trousers): Protect the body
g Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes
(with toecaps): Protect the feet
h Shin guards: Protect the legs
Failure to observe these precautions could result in damage to your sight or hear-
ing, or lead to a serious injury.
When necessary, please use the protective gear below.
Dust mask: Protects the breathing apparatus
Bee net: To deal with attacks by bees
Wear proper clothing.
Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the unit.
Do not wear open toed footwear, or go bare-foot or barelegged. In certain situations, to-
tal face and head protection may be required.
Failure to observe these precautions could result in damage to your sight or hearing, or lead
to a serious injury.
9
Description
Description
1. Brushes - Permanently attached to drum holders and
come standard with 0.5 mm diameter nylon bristles. Op-
tional 0.7 mm diameter brushes are available for fine
material sweeping application.
2. Lower drive shaft assembly - Included separately in
the carton and must be assembled to the ProSweep/
gear housing assembly. Contains flexible drive cable,
outer shaft housing and safety decal.
3. Flexible drive cable - Cable end fits into drive shaft
coupler of Pro Attachment Series or Split Boom models.
Lubricate drive cable every 25 hours with high tempera-
ture automotive grease.
4. Brush gear housing assembly - Brushes come pre-
assembled to the gear housing in the carton. Brushes
rotate towards the operator viewed from the operators
position.
5. Type and serial number
10
Before you start
Before you start
Packing list
Assembly
Gear housing assembly to lower drive shaft assembly
1. Remove vinyl cap from attachment drive shaft.
2. Place brush gear housing assembly on a flat surface with
gear housing shaft mount at 45° angle.
3. Remove gear housing locator screw (A).
4. Loosen gear housing mounting bolt (B).
The following parts are packed separately in the packing box.
When you have unpacked the box, please check the parts that it contains.
Contact your dealer if anything is missing or broken.
1. Lower drive shaft assembly
2. Brushes / gear housing assembly
3. Storage hook assembly
4. Operator's manual
WARNING
Read the operator's manual carefully to ensure that you assemble the product correctly.
Using a product that has been incorrectly assembled could lead to an accident or serious injury.
11
Before you start
5. Position lower drive shaft (end without serial number decal)
into gear housing shaft mount.
6. Align hole in drive shaft housing with gear housing shaft hole
(C) and seat lower drive shaft end into gear housing shaft
mount.
7. Install and tighten locator screw (A).
8. Tighten gear housing mounting bolt (B).
Power head shaft/lower shaft assembly
1. Turn gear housing assembly over so that gear housing
mounting bolt (E) faces upward.
2. Pull locator pin (A) out, and turn anticlockwise 1/4 turn to
lockout position.
3. Remove cardboard spacer from coupler, if necessary.
4. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages upper drive shaft mount.
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower
shaft hole. Insure locator pin is fully engaged by twisting low-
er drive shaft. Locator pin should snap flush in coupler. Full
engagement will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamp-
ing knob (D).
7. To disassemble, reverse assembly instructions.
CAUTION
Thrown objects hazard. Install lower drive shaft so that gear
housing mounting bolt (E) faces upwards. Otherwise debris will
be thrown toward user.
12
Operation
Operation
1. Hold unit on your right side resting sweeper brushes on work
surface.
2. Firmly grasp rear grip with right hand and front handle with
left hand.
3. Position unit at an angle to the work surface well out in front
of your body.
4. Accelerate to full speed and allow brushes to push debris
ahead. Sweep to an area where debris can be piled and col-
lected.
5. Debris may be swept out and away from corners by turning
unit over to reverse brush direction. Grip unit securely using
both hands. Operate trigger lever with thumb of right hand.
For extended use, reposition front handle to allow comforta-
ble grip. Return handle to normal position for regular opera-
tion.
6. When sweeping wide areas, angle brushes to pile debris in
rows; then collect material.
7. Use an angle of 15-30º. This helps direct debris and reduces
operator fatigue.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
Always turn off the unit, disconnect the spark plug wire or remove the battery, and make sure all moving parts have
come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Failure to observe these instructions could lead to an accident or injury.
NOTE
When use the electric motor unit: if you first use the unit under low temperature after purchase, it may not operate smoothly
in rare instances. This phenomenon does not indicate a product failure. In this case, condition the unit to room temperature
(normal temperature), and turn on and off power to the unit repeatedly before use.
WARNING
The sweeper brushes rotate towards the operator. Do not
operate unit at an angle with brushes close to your body
which could result in loss of control and possible serious
injury.
IMPORTANT
When use the engine: extended use of unit at low throttle set-
tings could cause damage to clutch because of clutch slipping.
WARNING
Turning unit over to reverse sweeper drum rotation will
cause debris to be swept toward operator. Reduce speed,
and be alert for unstable footing caused by loose debris.
13
Maintenance and care
Maintenance and care
Servicing guidelines
Maintenance and care
Lubrication
Gear housing
1. Clean all loose debris from gear housing.
2. Remove screw plug (A) and check level of grease.
3. Add grease if necessary. Do not over fill.
4. Install screw plug (A).
Drive shaft assembly
1. Remove gear housing locator screw (A).
2. Loosen gear housing mounting bolt (B).
3. Pull gear box from drive shaft housing.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop the unit, disconnect the spark plug wire or remove the battery, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before
performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
Component/System Maintenance Procedure Frequency
Drive shaft Grease Every 25 hours of use
Gear housing Grease Yearly
Brushes Inspect/Tighten/Replace Before each use
Screws, bolts and nuts Inspect/Tighten/Replace Before each use
IMPORTANT
Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance.
IMPORTANT
Lower and upper drive shaft must be lubricated with grease
every 25 hours of operation, otherwise drive shaft assembly
overheating and failure can result.
14
Maintenance and care
4. Pull flexible cable from the drive shaft housing, wipe clean
and re-coat with a thin coating 15 ml of Lithium based
grease.
5. Slide the flexible cable back in the drive housing. Do not get
dirt on the flex cable.
6. Position lower drive shaft (end without safety decal) into gear
housing shaft mount.
7. Align hole in drive shaft housing with gear housing shaft hole
(C), and seat lower drive shaft end into gear housing shaft
mount.
8. Install and tighten locator screw (A).
9. Tighten gear housing mounting bolt (B).
Brush replacement
Brushes that are broken off, deformed, or worn to within 25.4 mm
of the brush holder drum should be replaced for best sweeping
efficiency.
1. Locate brush holder access hole (A) near outer drum end.
2. Hold 8 mm nut (B) from turning with open end wrench insert-
ed through drum holder cap.
3. Loosen and remove bolt and lock nut with cross head screw-
driver through holder access hole (A).
4. Remove drum cap (C). Slide brush holder drum off square
axle shaft.
15
Maintenance and care
5. Install new brush holder drum, aligning hole (A) in drum axle
with axle shaft hole.
6. Install drum cap, aligning cap holes with axle shaft and brush
holder drum holes.
7. Install bolt and locknut. Tighten securely.
16
Storage
Storage
1. Clean this attachment bristles with water.
2. Apply thin coating of oil to metal parts to prevent rust.
3. Lubricate lower shaft assembly with grease.
4. Store this attachment in a dry place out of reach of children.
Do not store attachment with the weight resting on brushes
which could bend over a long period of time. Store attach-
ment with lower shaft housing in a horizontal or vertical po-
sition to prevent grease loss from open shaft end.
Storage hook installation
1. Insert small end of hook into locating hole on attachment
shaft.
2. Slide plastic cap onto end of attachment shaft.
IMPORTANT
Do not immerse this attachment in water. Water will enter gear
housing and damage gears, bearings and seals.
17
Specifications
Specifications
MTA-PS
External dimensions:
Length x Width x Height 797 × 598 × 317 mm
Masses 5.3 kg
Drive Shaft 6.15 mm
Lubrication Good quality lithium grease
Gear Case
Reduction ratio 42.75
Lubrication Good quality lithium grease
Rotational direction of output seen from right side Anticlockwise
maximum rotational frequency of the spindle 280 r/min
Brushes
Specified brush diameter 317 mm
Max sweeping width 589 mm
Vibration levels: (ISO 22867) ahv,eq
Front handle / Rear handle 4.7 / 4.6 m/s²
Uncertainty: K 4.0 m/s²
Sound pressure level: (ISO 22868) LpAeq 94.9 dB (A)
Uncertainty: KpA 2.5 dB (A)
Sound power level: (ISO 22868) LWARa 105.7 dB (A)
Uncertainty: KWA 2.5 dB (A)
Applicable model PAS-2620ES and M262S
18
Specifications
These specifications are subject to change without notice.
MTA-PS
External dimensions:
Length x Width x Height 797 × 598 × 317 mm
Masses 5.3 kg
Drive Shaft 6.15 mm
Lubrication Good quality lithium grease
Gear Case
Reduction ratio 42.75
Lubrication Good quality lithium grease
Rotational direction of output seen from right side Anticlockwise
maximum rotational frequency of the spindle 220 r/min
Brushes
Specified brush diameter 317 mm
Max sweeping width 589 mm
Vibration levels: (ISO 22867) ahv,eq
Front handle / Rear handle 2.5 / 1.3 m/s²
Uncertainty: K 1.5 m/s²
Sound pressure level: (ISO 22868) LpAeq 77.3 dB (A)
Uncertainty: KpA 3.0 dB (A)
Sound power level: (ISO 22868) LWARa 90.1 dB (A)
Uncertainty: KWA 3.0 dB (A)
Applicable model DPAS-2600
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Shindaiwa MTA-PS Manuale utente

Tipo
Manuale utente