WisyCom MCR54 Manuale utente

Multi-band

Quad True Diversity

Camera Receiver

rev.7 (reference FW 1.7)

Date: 26 March 2021

MCR54 User Manual

1

SAFETY INSTRUCTION

 Read this safety instruction and the manual first

 Follow all instructions and information.

 Do not lose this manual.

 Do not use this apparatus under the rain or near the water.

 Do not install the apparatus near heaters or in hot environments, do not use outside the

operating temperature range.

 Do not open the apparatus, only qualified service technicians are authorized to operate on it.

The apparatus needs servicing when it is not properly working or is damaged by liquids,

moisture or other objects are fallen in the apparatus.

 Use only accessories or replacement parts authorized or specified by the manufacturer.

 Clean the apparatus only with dry cloths, do not use liquids.

 Report the serial number and the purchasing date in front of the manual. It is needed to have

proper replacement parts or accessories from the manufacturer.

 When replacement parts are needed, use only replacement parts authorized from the

manufacturer. Substitution with not authorized parts could result in electric shock, hazards or

fire.

 Keep attention on all the labels with warnings or hazards on the apparatus.

WARNING: The apparatus is intended for professional use; the manufacturer alerts the user that

the headphone output power of the apparatus could exceed the level of 85 dB(A) of sound

pressure level and this could be dangerous for the hearings. Do not use the headphone with high

power level or for long time. Reduce the power or suspend the hearing in case of any kind of

hearing problem.

MCR54 User Manual

2

MAIN FEATURES

MCR54 is a camera mount quad true diversity wireless-microphone receiver system in a modular

stand-alone or slot-in configuration (compatible with most camera’s slot):



Wideband just isn’t enough anymore! Upgrade to a Multi-Band system with up 790 MHz

tuning range to find your frequency, anywhere in the World.



With the combination of Narrowband Modulation (High Density) and Linear transmitters,

set your channels every 200kHz without intermodulation distortion and get an extra 3dB

sensitivity.

 With eight internal receiver boards, the MCR54 boasts an unprecedented capacity for

range and reliability.

 DSP delivers ENC and ENR algorithms for perfect audio in any application with less than

1ms delay –Create and shape presets for the desired sound. This enables the use of

third-party transmitters with Wisycom receivers



Modular configurations for stand-alone or slot-in formats in many Cameras or Audio

Devices



Monitor & control through USB C or Bluetooth 5 (long range) on Wisycom Manager 2.2

(computer SW)



High contrast OLED display and 4 buttons enable quick manual setup



DSP Analog & Digital Audio Output (AES3)



Extreme low noise VCO with ultrafast spectrum scan for optimal quick & easy setup



Wisycom exclusive digital sub-carrier telemetry technology enables:

o

remote TX battery monitoring

o

advanced tone-squelch operating

o

Push-to-talk function (via optional back-panel module):

Simply pushing this button (PTT), the presenter causes the remote switching of the

receiver’s output-line, from the “main line” to the additional “intercom line”, in order to

be able to talk “off-air” directly with the technical team. Then all PTT’s MICs can be

connected in pre-fading allowing a clever intercom setup.



Rear antenna connectors and micro audio and power adapter

 40 groups of 60 channels fully user programmable (2400 frequencies)

TECHNICAL DESCRIPTION

The MCR54 is a professional quad true diversity receiver for wireless microphones reception

designed for broadcast television production, live performances, theatres and many other

professional applications.

The winning features:

 High immunity on strong RF environment

 Massive switching bandwidth

 Dynamic audio performances and flexibility with analog or digital processors

 Unprecedented reliability and durability

MCR54 User Manual

3

One of the milestones in the design of the MCR54 is unprecedented reliability: most of the circuitry

of the receiver is independent one from each other. Above a schematic with an overview of main

receiver functions.

RF layout:

For each antenna the RF signal is split in 4 to receiver 1,2,3 and 4 (antenna A and antenna B) with a

wide band splitter. Then 3 banks of filters are selected according to the frequency of the 4

receivers:

MCR54-B1 (UK)

MCR54-B2 (USA/EU)

MCR54-B3 (JP)

FILTER BANK 1:

470-800MHz Tuneable filter with 32MHz of bandwidth

FILTER BANK 2:

961-1000 MHz

823-832 MHz

806-810 MHz

FILTER BANK 3:

1045-1075 MHz

940-960 MHz

1240-1260 MHz

NOTE: the tuning frequencies of all the 4 receivers has to be in the same bank of filter!

All the 4 receivers are true diversity receivers: each one is made of two receivers tuned on the

same frequency. Subsequently the selection of the band filter between 100 kHz or 200kHz allows

to work with Narrowband (High Density) or Wideband transmitters respectively.

Each receiver has its own demodulated signal and its own RSSI signal (Receiver Signal Strength

Indication); RF squelch used measurement of RSSI level for antenna diversity and for audio

enabling. In addition to the RSSI level, each receiver measures the Channel Quality. It is a more

powerful tool than RF squelch because it actually looks at the quality of the signal from the TX

relative to the noise floor on the channel which can vary over time. With the noise squelch set to

on you can set the RF squelch to a much lower level.

A DSP selects or combines signals from section A & B to have the best audio.

MCR54 User Manual

4

Audio Layout

As shown on the above schematic, MCR54 provides the following audio signals:

 HP [HEADPHONE]: an analog monitor audio output to headphone 3.5mm jack socket.

Thanks to the “Setup>Headphone” menu the user can select which of the 4 receivers he

wants to listen to and can adjust the volume from 0 to -24 step 1dB.

 BOT [MAIN]: 4 audio signal streams come out in the connector on the bottom and

depending on the plugged slot-in can be configured according to the following table:

Slot in (SLK54-IK/SX)

BASE outputs (on BPA54)

CH1

CH2

CH1

CH2

CH3

CH4

AES3 en.

None

An [RXi]

An [RX1]

An [RX2]

An [RX3]

An [RX4]

AUX

An [RXi]

An [RX1]

An [RX2]

An [RX3]

An [RX4]

MAIN

(Base

outputs)

AES**

[RX1+RX2]

AES**

[RX3+RX4]

AES

[RX1+RX2]

AES

[RX3+RX4]

-

 TOP [AUX]: 2 audio signal streams come out in the TA5 top feed connector and can be

configured in digital (enabling AES3 on AUX outputs) or in analog

AUX (on TOP FEED)

CH1

CH2

AES3 en.

None

An [RXi]

AUX

AES

[RX1+RX2]

AES

[RX3+RX4]

MAIN

(Base outputs)

An [RXi]

MCR54 User Manual

5

Product overview

❶

SMA antenna connectors

❷

Mini XLR 5-pin connector

2 channels analog audio outputs electronically balanced or

4 channels digital audio outputs (AES3)

1 GND

2 CHANNEL1+

3 CHANNEL1-

4 CHANNEL2+

5 CHANNEL2-

❸

LED power supply

GREEN The receiver is on with an external power supply

PALE GREEN The receiver is on with battery

GREEN BLINKING The external power is low

PALE GREEN BLINKING The power of the battery is low

RED BLINKING Relative transmitter battery is low:

- slowly blinking if 25% lifetime

- quickly blinking if 12% lifetime

❹

Led Bleutooth BLUE

❺

DISPLAY 128 x 96 pixels

❻

LED receiver status

OFF Relative receiver is not active

RED RF level below squelch and/or Noise squelch on both diversity receivers

RED BLINK frequency is out of filter (32MHz) see NOTE page 3

GREEN RF level above squelch and/or Noise squelch and receiver A is active (ANTENNA A)

BLUE RF level above squelch and/or Noise squelch and receiver B is active (ANTENNA B)

❼

Headphone output (jack 3.5 mm)

❽

“PWR/EXIT” BUTTON

Push and keep this button to power on/off the receiver. The on/off status is permanently

memorized into the non-volatile memory, this way the system can be setup to automatically

turn on the receiver when power up.

During menu navigation push this button to exit from current menu (escape function).

❾

“MENU/SEL” BUTTON

Push this button to navigate function menu’s and to confirm the chosen setup.

❿

“Arrow down/SCAN” BUTTON

Push and keep this button to start the automatic scan.

During menu navigation push this button to move-down and select the previous item.

⓫

“Arrow up/SYNC” BUTTON

Push and keep this button to start a synchronization with a Wisycom transmitter (follow

instructions on display). Before starting synchronization IRDA must be enabled on Wisycom

transmitter.

During menu navigation push this button to move -up and select the previous item.

❷

❹

❸

❶

❼

❺

❶

❻

❾

❽

⓫

❿

MCR54 User Manual

6

Display menu

Using navigation buttons it is possible to quick & easy navigate through the menu:

- SEL/Exit to enter or exit a level

- Arrow up/down to circle on the same level

- To save the modified parameters press and hold the SEL /MENU button ❾ until appears the

message "SAVED!".

Status screen

Tree menu

Main

Preset

Active

Load

U01-Preset1/U02-Preset2/U03-Preset3…. U16-Preset16

Save

U01-Preset1/U02-Preset2/U03-Preset3…. U16-Preset16

Factory

Setup

Info

Supply/ Model / Serial / Range / Base / HW/ FW / Diagnostic / Alarms

Bluetooth

Pwr on

No/Yes

Group

Channel

Frequency

Audio Modulation Bar

(from -42 to 0 dB)

Peak deviation ≥ 56KHz

RF bar

(8 steps of 10dBµV,

from 10 to 80 dBµV)

TX Battery

Level

RX Number

WARNING!

RX Number and Rx red

LED blink if frequency is

out of filter (32MHz)

see NOTE page 3

MCR54 User Manual

7

Infrared:

By activating the infrared, you can connect the MCR54 to other devices (such as Wisycom

Transmitter MTP40S/MTP41S/MTH410/MTB40S o the programmer UPKmini)

Preset:

The preset menu has the following two submenus:

 Act: that allows to verify the active preset

 Load: that allows to reload up to 16 Preset

 Save: that allows to save up to 16 Presets

Setup:

Select Setup menu to access to the main parameters setting.

Info

In the info menu the following information are displayed:

Info

description

example

Supply

Supply voltage measured (on the rear connector)

12.0Volt

Model

MCR54

Serial

The serial number composed by 1 letter+7 numbers

X3536539

Range

Frequency range according to the MCR54 band

(minimum and maximum frequency)

470--960

Base

Version of rear panel:

BPA54

SLK 54-SX

SLK 54-IK

BPA54

HW

Country

Country code

EU

Main rev.

Hardware revision of the main board

1

Main opt.

Option of the main board

-

RF rev.

Hardware revision of the RF board

2

RF opt.

Option of the RF board

-

Panel rev.

Hardware revision of the panel board

1

Panel opt.

Option of the panel board

-

Base rev.

Hardware revision of the Base (rear panel)

0

Base opt.

Option of the Base (rear panel)

-

FW

Version:

FW version

v2.0.5

BL:

Bootloader version

v.1.0.18

App:

Application version

v2.5d

DSP:

DSP version

v0.0.55r

Diagnostic

Alarms

Number of alarms.

If the number of alarms is > 0 push SEL button to enter on

the Alarms list. For each error a brief description and the

error code is showed.

0

MCR54 User Manual

8

Setup Menu

Active RXs

RX1 RX2 RX3 RX4

Edit RX1/RX2/RX3/RX4

Name

"8 characters max"

Frequency

Group / Channel and Frequency selection

Ch. Modulation

Wide/Narrow (HD)

Compander

ENR Wis/ENC Wis…

Sq. mode

Long Range/Normal/User

Audio Out

LINE level

AES3 level

Sign. Phase

Cal. Tone

Cal Tone

OFF/ON

Frequency

400/600/1000 Hz

Level

-30 to 0 dB (1 dB step)

Sync

Scan

Scan now

Channel/Freq

Scan squelch

OFF- 0/3/6/9/12/15/18/21/24/28/32/36/40/46 dBμV

Scan BNT

Channel/Freq

View last

Headphones

Volume

0/-24 step 1dB

RX sel

RX1/RX2/RX3/RX4

Display

LED mode

Full/Alarm/OFF

Brightness

0/5

Low Timeout

5/60 sec (step 5 sec)

OFF Timeout

10/120 sec (step 10 sec) / OFF

Adv. Audio

AES3 enabled

None/MAIN/AUX

AUX1

RX1/RX2/RX3/RX4

AUX2

RX1/RX2/RX3/RX4

AUX1 level

18dBu/-24dBu step 1dB

AUX2 level

18dBu/-24dBu step 1dB

Signalling

Audio off

RX1 RX2 RX3 RX4

visible only with

SLK54-IKSS

TX Batt.

RX1 RX2 RX3 RX4

Act. Code

Panel locked

No/Yes

MCR54 User Manual

9

Power on

Allow to enable/disable each single receivers:

Edit RX (same menu for each of the 4 receivers)

Edit RX: Name

Selecting Name, it’s possible to edit the name of the receiver (12 characters). The number of visible

characters depends on the type of characters used (uppercase or lowercase characters).

Edit RX: Frequency

Select current group and channel. If the specific group/channel is not locked, frequency can be

edited in this menu.

Edit RX: Channel modulation

Narrowband or Wideband software selectable according to transmitter modulation.

NOTE: During the SYNC process the receiver sends the type of modulation (NB or WB) and the TX adapts

automatically to the receiver’s modulation settings accordingly.

Edit RX: Compander

MCR54 supports 5 different type of “Compander systems” (others on request through Digicom)

ENS: designed for voice and music applications

ENR-Wisy: designed for maximum noise reduction. Ideal for use in louder environments.

ENC-Wisy: designed for maximum audio fidelity (use this in case of special vocal application or to

remote instruments). Ideal for use in quite environments.

ENR-1.2*/ENC-1.2*: to use with some type of camera (ex. Canon® C300, Canon® XF305, Sony®

Pmw200, Sony® Pmw300, Sony® PmwF5, Sony® Fs7, Nikon® D600 or Nikon® D800,

Canon® SD mark3...) which accept a signal with reduced dynamic. This type of expansion

doesn't add artifacts to the signal and allows to have a less noisy signal. It allows to

improve the quality of the audio registration (compared to the ENR/ENC standard)

increasing the S/N ratio up to 15dB.

To use these expanders, it’s necessary to set ENR on the transmitter and ENR 1.2 on the

receiver or set ENC on the transmitter and ENC 1.2 on the receiver.

ENR-1.2 it’s used for the optimization of noise, ENC-1.2 it’s used to optimize the voice.

NOTE: The compander of the receiver must be the same as the transmitter

MCR54 core is a power digital audio processor that, besides an unbeatable audio quality and

flexibility, can emulate most expanders systems on the market. On this menu you can setup the

MCR54 User Manual

10

audio expanding chipset emulation. ENR is emulating the Philips™ SA572 and PTT digital data of

Wisycom transmitters. Other setups can be loaded on request.

Edit RX: Sq. Mode

Squelch Mode is available in 2 possible configurations: Normal or Long Range.

Relevant setup are summarized in the following table:

FIXED PARAMETERS

RF squelch

[dBµV]

Noise

Squelch [dB]

Squelch ON

delay [ms]

Tone squelch

TSQ delay

[ms]

Normal

6

11

0

ON

500

Long

Range

3

8

0

OFF

500

NOTE: For expert users, there is an 4

th

configuration named User which allows to modify each

single parameter using the Wisycom Manager.

VARIABILE PARAMETERS

RF squelch

[dBµV]

Noise Squelch

[dB]

Squelch

ON delay

[ms]

Tone squelch

TSQ delay

[ms]

User

OFF/0/3/6…

/46

From 8 to 25

0 to 2000

ON/OFF

0 to 2000

RF Squelch

RF squelch is a function that acts to suppress the audio output of a receiver in the absence of a sufficiently

strong desired input signal.

Noise Squelch

Noise squelch is a more powerful tool than RF squelch because it actually looks at the quality of the signal from

the TX relative to the noise floor on the channel which can vary over time. With the noise squelch set to ON

you can set the RF squelch to a much lower level.

Tone Squelch

MCR54 is able to detect a digital tone squelch generated by a Wisycom transmitters (ex.

MTH410/MTH400/MTP40S/ MTP41S/MTB40S/RPU500).

Tone squelch ON: when the tone squelch is enabled the audio is muted unless the correct carrier is detected.

Tone squelch allows to work with lower RF squelch, increasing the coverage and the robustness especially in

presence of digital television carriers (DVB-T).

Edit RX: Audio Out

Max audio level output can be set:

 from -24dBu to 18 dBu for analog output

 from 0 to -30 dBFS step 1 for digital AES3 output

Edit RX> Audio Out: Sig. Phase

To change audio phase of 0 deg. or 180 deg.

MCR54 User Manual

11

Edit RX> Audio Out: Cal. Tone

If Cal. tone is enabled, a calibration tone is transmitted from the outputs of the receiver and the

audio LED of the relative RX become blue (to turn off the calibration tone, go on the menu

Advanced > RX and press EXIT)

It’s possible to select the audio level between -30dB to 0 dB (referred to the maximum output

level set on the audio outputs). It represent the reference of the peak deviation (56KHz).

The frequency of the tone can be chosen between 400/600/1000 Hz.

Edit RX: Sync

The SYNC function is useful to tune a transmitter on the same

frequency of the receiver via the IR interface. Before starting

the sync function tune the receiver on desired channel,

manually or using the SCAN utility. After this, enable the IR

interface on the transmitter. Now press UP&EXIT buttons

together or enter in the Sync menu to start the SYNC function.

Keep the IR window of the transmitter in front of the IR window of the receiver and, as soon as the

connection is done, the receiver will send to the transmitter all the information needed.

If the operation is not possible, (i.e. the frequency range of the transmitter is not compatible with

the frequency of the receiver), the display will show an error message.

If the transmitter has the function “NAME” enabled, when the sync function is completed it will

show the same name of the synchronized receiver.

MCR54 User Manual

12

Scan

The MCR54 allows the user to scan using the Group/Channel frequency file in the unit or by

scanning a manual selection of frequencies. Select which type of scan by going into the scan menu.

Channel

Once started a channel scan operation the receiver asks for

group to be used*. Press and hold the SEL button to select the

group to scan.

Then it prompts to turn off all transmitters. This is in order to

provide the most accurate scan data.

Press SEL to start the scan!

After few seconds, scan results are displayed sorted by level,

making easier to pick up the best one.

The dotted line in the graph indicate the squelch threshold.

Under the graph are reported the following parameters:

- Ch: Channel

- Rank: Ranking position (Best/Lowest Noise Level to

Worst/Highest Noise Level)

- Freq: Frequency

- Lev: RF level

Pushing simultaneously UP and DOWN button, the results can

be also displayed on a chart in ascending order according to

the number of the channel.

After the selection of the desired channel, a screen appears

with the selected frequency, channel and group and it is

possible to Set or Synchronize the receiver with the

transmitter. We recommend setting the frequency and then

synchronize it with the transmitter.

MCR54 User Manual

13

Headphones:

This menu the user can select which of the 4 receivers he wants to listen to and can adjust the

volume from 0 to -24 step 1dB.

Display:

In this menu item it’s possible to set the mode of switch on of the front LEDs and the contrast and

timeout of the display.

LEDs mode can be:

 Full: all LEDs are activated

 Alarm: the LEDs are ON only in case of alarm (only red)

 OFF: all LEDs are always off

Low timeout indicates the time until the display stays on with the contrast set (after which, the

display contrast is lowered and after another “Low timeout” the display shows the Status screen).

Freq

The Frequency scan allows to select a range of frequency to

scan, between a maximum and a minimum value and the step

with which to perform the scans. Press and hold the SEL

button to confirm.

Then it prompts to turn off all transmitters.

Press SEL to start the scan!

After few seconds, scan results are displayed on a chart in

ascending order according to the frequency (step 1MHz). The

dotted line in the graph indicate the squelch threshold.

Pushing simultaneously UP and DOWN button it’s possible to

zoom the graph to show all the steps of scan

After the selection of the desired frequency, a screen appears

with the selected frequency and the RF level and it is possible

to Set or Synchronize the receiver with the transmitter. We

recommend setting the frequency and then synchronize it

with the transmitter.

MCR54 User Manual

14

Off timeout is the time until the display stays on (after which, the display will automatically turn

off). If Off timeout is set to OFF the display never turn off automatically.

Advanced audio:

This menu allows to decide the type of audio outputs (digital AES3 or analog) and what receivers

come out to the connectors.

Depending on the plugged slot-in it can be configured according to the following tables:

With BPA54 it is possible to enabled AES outputs on AUX (Top Feed) or on MAIN (Base outputs).

When AES is disabled (set to None) or enabled on AUX, analog Base outputs can be configured

with any combination of 2 receivers (RX1+RX2, RX2+RX3, …)

AUX (on TOP FEED)

BASE outputs (on BPA54)

1 GND

2 CHANNEL1+

3 CHANNEL1-

4 CHANNEL2+

5 CHANNEL2-

CH1

CH2

CH1

CH2

CH3

CH4

AES3 en.

None

An [RXi]

An [RX1]

An [RX2]

An [RX3]

An [RX4]

AUX

AES

[RX1+RX2]

AES

[RX3+RX4]

An [RX1]

An [RX2]

An [RX3]

An [RX4]

MAIN

(Base outputs)

An [RXi]

AES

[RX1+RX2]

AES

[RX3+RX4]

-

With SLK54-IK it is possible to enabled AES outputs on AUX (Top Feed) or on MAIN (Base Outputs).

When AES is disabled (set to None) or enabled on AUX, analog Base outputs can be configured

with any combination of 2 receivers (RX1+RX2, RX2+RX3, …)

AUX (on TOP FEED)

BASE outputs (on SLK54-IK)

2 CHANNEL1+

3 CHANNEL1-

15 CHANNEL2+

16 CHANNEL2-

1 GND

2 CHANNEL1+

3 CHANNEL1-

4 CHANNEL2+

5 CHANNEL2-

CH1

CH2

CH1

CH2

AES3 en.

None

An [RXi]

AUX

AES

[RX1+RX2]

AES

[RX3+RX4]

An [RXi]

MAIN

(Base outputs)

An [RXi]

AES [RX1+RX2]

AES [RX3+RX4]

MCR54 User Manual

15

With SLK54-SX it is possible to enabled AES outputs only on AUX (Top Feed). Analog Base outputs

can be configured with any combination of 2 receivers (RX1+RX2, RX2+RX3, …)

AUX (on TOP FEED)

MAIN (on SLK54-SX)

2 CHANNEL1

3 CHANNEL2

1 GND

2 CHANNEL1+

3 CHANNEL1-

4 CHANNEL2+

5 CHANNEL2-

CH1

CH2

CH1

CH2

AES3

en.

None

An [RXi]

AUX

AES [RX1+RX2]

AES [RX3+RX4]

An [RXi]

MCR54 User Manual

16

ACCESSORIES AND PARTS

BPA54: Stand alone socket

Hirose HR10A-F

1 GND

4 +VDC

1 GND

2 CHANNEL1+

3 CHANNEL1-

4 CHANNEL2+

5 CHANNEL2-

1 GND

2 CHANNEL3+

3 CHANNEL3-

4 CHANNEL4+

5 CHANNEL4-

SLK54-SX: Sony slot-in

"Slot-in" kit (upper flange +rear-panel) for Sony camera.

SUBD-15pin:

1 GND

2 CH1 Anal (unbalanced)

3 CH2 Anal (unbalanced)

4 VDC

NOTE:

not all Sony cameras has the internal double pin enable.

CHECK IF YOUR CAMERA SUPPORT 2 CHANNELS ON SLOT-IN

SLK54-IK: Ikegami super slot

“Slot-in” compatible with:

- Sound Device SuperSlot (4 audio outs in capable devices,

i.e. Soundevices™ SL-2)

- MRK16 Multi Slot rack (4 audio out)

- Unislot (Ikegami, Panasonic cameras1)

SUBD-25 pinout:

1 GND

2 CH1+ Anal/ CH1,2 AES3+

3 CH1- Anal/ CH1,2 AES3-

4 GND

5 VDC (6-18 VDC)

6 RX_ON

7 RX_WARNING

15 CH2+ Anal/ CH3,4 AES3+

16 CH2- Anal/ CH3,4 AES3-

22 UART from Wireless receiver

23 UART to Wireless receiver

25 GND

MCR54 User Manual

17

BCA54: Stand alone with

lithium battery pack

- 2 mini XLR-5pin male audio

outputs

- 1 Hirose connector for external

power

- Battery pack for RRC2040

33.2Whr

lithium battery

CABLES

CAM50-3

AF cable (50 cm), mini XLR-5F / 2 XLR-3M

connectors

FOR ANALOG OUTPUTS (2 channels)

CAM50-41

AF cable (50 cm), mini XLR-5F / 1 XLR-3M

connectors

FOR AES3 DIGITAL OUTPUTS (2 channels)

CDC34

External power feeding cable, hirose/raw wires (50

cm)

PSP910-H

AC/DC Power Supply, Switch Mode with Hirose 4 pin

connector (to use one “desktop” apparatus alone)

Input:100 ÷ 240V ac

Ouput:12V@700mA, 8W

Plug type: EU

MCR54 User Manual

18

CAUSBC1

USB Cable 1m

USB B - USB C Male Black

To monitor/control/power on MCR54 receiver

CAP52-IK

STAND ALONE HARNESS CABLE- DB25

(to MCR54/MCR42,Ikegami/Panasonic slot-in

compatible)

2 XLR-3M (line output isolated with audio

tranformer) + hirose (for power supply)

MCR54 (2 analog audio outputs or 4 AES3 audio

outputs)

CAP52-SX

STAND ALONE HARNESS CABLE- DB15

to MCR54/MCR42, Sony slot-in compatible)

2 XLR-3M (line output isolated with audio

tranformer) + hirose (for power supply)

MCR54 (2 analog audio outputs)

ANTENNAS

AWS-BK

Whip antenna UHF 470-608 MHz

SMA connector, black cap

AWS-YL

Whip antenna UHF 572-694 MHz

SMA connector, yellow cap

AWS-GN

Whip antenna UHF 670-870 MHz

SMA connector, green cap

AWS-BL

Whip antenna UHF 820-1160 MHz

SMA connector, blue cap

AWS-RD

Whip antenna UHF 1060-1300 MHz

SMA connector, red cap

MCR54 User Manual

19

AWS-BK-RA

Whip antenna UHF 470-700 MHz

SMA connector, black cap

Right angle

AWS-GN-RA

Whip antenna UHF 670-870 MHz

SMA connector, green cap

Right angle

AWS-BL-RA

Whip antenna UHF 820-1160 MHz

SMA connector, blue cap

Right angle

How to update the firmware:

1. Connect the MCR54 to the PC through the USB-C cable

2. Check if the version of Wisycom Manager installed in your PC is the latest version. If not,

upgrade to the new version

3. Run Wisycom Manager

4. Power up the receiver MCR54

5. Push FW UPDATE button

6. Download the .xupf file from the website and load the file using FW library > Import

button.

7. Select the file

8. Select the receiver and Play

First the program erases the flash memory and later it writes the flash memory. A green bar below

the panel shows the progress of this process. Take care do not disconnect the USB

communication or power off the MCR54 during this process.

La pagina sta caricando ...

WisyCom MCR54 Manuale utente

WisyCom MCR54 Manuale utente

in altre lingue

Documenti correlati

Altri documenti