Motorola CLS446 Manuale utente

English

1

Contents

Safety And General Information 2

Transmit and Receive Procedure 2

Exposure to Radio Frequency Energy 2

Portable Radio Operation and EME Exposure 3

Electromagnetic Interference/Compatibility 3

Safety and General Use While Driving 4

Operational Warnings 4

Operational Cautions 5

Charger Safety Instructions 5

Getting Started 7

Diagram of your radio 7

Your New Radio 8

Turning Your Radio On and Off 8

Radio Etiquette 8

Batteries and Battery Charging 8

Talking And Listening 12

Setting the Channel 12

Setting the Code 12

Features 12

Hands Free Use (VOX) 12

Call Tones and Vibrate Feature 13

Scan 13

Voice Scrambling 14

Microphone Gain 14

Signal Strength and Channel Busy Indicator 14

Keypad Lock 15

Roger Beep (Talk Confirmation Tone) 15

Time-Out Timer 15

Keypad Tones 15

Battery Save Mode 15

Restore Factory Defaults 15

Fitting the Swivel Holster 16

Further Information 16

Talk Range 16

Troubleshooting 17

Use and Care 19

Specifications 19

Warranty Information 20

Copyright Information 20

?????-CLS446 User Guide 25/9/03 4:11 PM Page 1

2

English

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio

The information provided in this document supersedes the

general safety information contained in user guides

published prior to July 2000.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver.

To control your exposure and ensure compliance with the

general population/uncontrolled environment exposure

limits, always adhere to the following procedure:

• Transmit no more than 50% of the time.

• To transmit (talk), press the Push to Talk (PTT) button.

• To receive calls, release the PTT button.

Transmitting 50% of the time, or less, is important because

the radio generates measurable RF energy exposure only

when transmitting (in terms of measuring standards

compliance).

Exposure to Radio Frequency Energy

Your Motorola radio is designed to comply with the

following national and international standards and

guidelines regarding exposure of human beings to radio

frequency electromagnetic energy:

• United States Federal Communications Commission, Code

of Federal Regulations; 47 CFR part 2 sub-part J

• American National Standards Institute (ANSI)/Institute of

Electrical and Electronic Engineers (IEEE) C95. 1-1992

• Institute of Electrical and Electronic Engineers (IEEE)

C95.1-1999 Edition

• International Commission on Non-Ionizing Radiation

Protection (ICNIRP) 1998

• Ministry of Health (Canada) Safety Code 6. Limits of

Human Exposure to Radio Frequency Electromagnetic

Fields in the Frequency Range from 3 kHz to 300 GHz, 1999

• Australian Communications Authority

Radiocommunications (Electromagnetic Radiation -

Human Exposure) Standard 2003 (applicable to wireless

phones only)

• ANATEL, Brasil Regulatory Authority, Resolution 256 (April

11, 2001) "additional requirements for SMR, cellular, and

PCS product certification."

To assure optimal radio performance and make sure

human exposure to radio frequency electromagnetic

energy is within the guidelines set forth in the above

standards, always adhere to the following procedures.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 2

English

3

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement

antenna. Unauthorized antennas, modifications, or

attachments could damage the radio and may violate FCC

regulations.

DO NOT hold the antenna when the radio is "IN USE."

Holding the antenna affects the effective range.

Two-Way Radio Operation

When using your radio as a traditional

two-way radio, hold the radio in a vertical

position with the microphone one to two

inches (2.5 to 5 cm) away from the lips.

Body-Worn Operation

To maintain compliance with FCC/Health Canada RF

exposure guidelines, if you wear a radio on your body

when transmitting, always place the radio in a Motorola-

supplied or approved clip, holder, holster, case, or body

harness for this product. Use of non-Motorola-approved

accessories may exceed FCC/Health Canada RF exposure

guidelines. If you do not use one of the Motorola-supplied

or approved body-worn accessories, and are not using the

radio held in the normal use position, ensure the radio and

its antenna are at least one inch (2.5 cm) from your body

when transmitting.

Data Operation

If applicable, when using any data feature of the radio with

or without an accessory cable, position the radio and its

antenna at least one inch (2.5 cm) from the body.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately

shielded, designed, or otherwise configured for

electromagnetic compatibility.

Facilities

To avoid electromagnetic interference and/or compatibility

conflicts, turn off your radio in any facility where posted

notices instruct you to do so. Hospitals or health care

facilities may be using equipment that is sensitive to

external RF energy.

Aircraft

When instructed to do so, turn off your radio when on

board an aircraft. Any use of a radio must be in

accordance with applicable regulations per airline crew

instructions.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 3

4

English

Medical Devices - Pacemakers

The Advanced Medical Technology Association

recommends that a minimum separation of six inches (15

cm) be maintained between a handheld wireless radio and

a pacemaker. These recommendations are consistent with

the independent research by, and recommendations of the

U.S. Food and Drug Administration.

Persons with pacemakers should:

• ALWAYS keep the radio more than six inches (15 cm)

from their pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the

potential for interference.

• Turn the radio OFF immediately if you have any reason to

suspect that interference is taking place.

Medical Devices - Hearing Aids

Some digital wireless radios may interfere with some

hearing aids. In the event of such interference, you may

want to consult your hearing aid manufacturer to discuss

alternatives.

Other Medical Devices

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to

assist you in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations on the use of radios in the

area where you drive. Always obey them. When using your

radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a

call if driving conditions so require.

Operational Warnings

For Vehicles With An Air Bag

Do not place a portable radio in the area over an air bag or

in the air bag deployment area. Air bags inflate with great

force. If a portable radio is placed in the air bag

deployment area and the air bag inflates, the radio may be

propelled with great force and cause serious injury to

occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a

potentially explosive atmosphere, unless it is a radio type

especially qualified for use in such areas as "Intrinsically

?????-CLS446 User Guide 25/9/03 4:11 PM Page 4

English

5

Safe." Do not remove, install, or charge batteries in such

areas. Sparks in a potentially explosive atmosphere can

cause an explosion or fire resulting in bodily injury or even

death.

Note: The areas with potentially explosive atmospheres

referred to above include fueling areas such as below

decks on boats, fuel or chemical transfer or storage

facilities, areas where the air contains chemicals or

particles, such as grain, dust or metal powders, and any

other area where you would normally be advised to turn

off your vehicle engine. Areas with potentially explosive

atmospheres are often but not always posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations,

turn off your radio when you are near electrical blasting

caps, in a blasting area, or in areas posted: "Turn off two-

way radio." Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged

antenna. If a damaged antenna comes into contact with

your skin, a minor burn can result.

Batteries

All batteries can cause property damage and/or bodily

injury such as burns if a conductive material such as

jewelry, keys, or beaded chains touch exposed terminals.

The conductive material may complete an electrical circuit

(short circuit) and become quite hot. Exercise care in

handling any charged battery, particularly when placing it

inside a pocket, purse, or other container with metal

objects.

Charger Safety Instructions

Before using the battery charger, read all instructions and

cautionary markings on:

1. the battery

2. the battery charger, and

3. the radio using the battery.

Caution: To reduce the risk of injury, only charge the

Motorola approved rechargeable battery for this product.

Other types of batteries may burst, causing personal injury

and damage.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 5

6

English

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has

received a sharp blow, or has been dropped or damaged

in any way.

3. Never alter the AC cord or plug provided with the unit. If

the plug will not fit the AC outlet, have the proper outlet

installed by a qualified electrician. An improper condition

can result in a risk of electric shock.

4. To reduce the risk of damage to the cord or plug, pull the

plug rather than the cord when disconnecting the

charger from the AC outlet.

5. To reduce the risk of electric shock, unplug the charger

from the AC outlet before attempting any maintenance or

cleaning.

6. Use of an attachment not recommended or sold by

Motorola may result in a risk of fire, electric shock, or

personal injury.

7. Make sure the cord is located so it will not be stepped

on, tripped over, or subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could

result in a risk of fire and/or electric shock. If an

extension cord must be used, make sure:

• That the pins on the plug of the extension cord are the

same number, size, and shape as those on the plug of the

charger.

• That the extension cord is properly wired and in good

electrical condition, and

• That the cord size is 18 AWG (1mm2) for lengths up to

100 feet (30 metres) and 16 AWG (1.3mm2) for lengths up

to 150 feet (45 metres).

9. The supply cord of this charger cannot be replaced. If

the cord is damaged please return to your place of

purchase.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 6

English

7

Getting Started

Diagram of your radio

Use P to:

Turn radio on or off

Adjust radio volume

Use B to:

Transmit call tone

Use T to:

Monitor the frequency

Scan channels

Use S to:

Lock the keypad

Scroll through menus

LED indicator lamp

Microphone

Accessory jack

Use Push to Talk (PTT) to:

Talk

Save a setting

Use ] and [ to:

Change channels

and codes

Change menu settings

Speaker

?????-CLS446 User Guide 25/9/03 4:11 PM Page 7

8

English

Your New Radio

Motorola CLS446 two-way radios operate on PMR446

frequencies, and can be used in any country where

PMR446 frequencies are authorized, subject to applicable

regulations. This license-free, two-way radio service is for

family and group recreational use. Use of this radio outside

the country where it was intended to be distributed is

subject to government regulations and may be prohibited.

Read this manual carefully and make sure you know how

to properly operate the radio before use.

Please retain your original dated sales receipt for your

records. For warranty service of your Motorola two-way

radio you will need to provide a copy of your dated sales

receipt to confirm warranty status.

Turning Your Radio On and Off

Turn P clockwise to turn the radio on, and adjust the

volume to a comfortable level. The radio will beep and both

the red LED and the segments on the display will illuminate

briefly. Turn P anticlockwise to turn the radio off.

Radio Etiquette

It is good radio etiquette to monitor the channel for activity

before you transmit, to ensure that you do not interrupt

other users already on the channel. Press and hold T

briefly to check for channel activity.If you hear static, the

channel is clear for use. Press T again to stop monitoring.

Batteries and Battery Charging

Your CLS446 radio operates with a rechargeable Lithium

Ion (Li Ion) battery. A battery tray is available which allows

3 AAA alkaline batteries to be used. Please contact your

dealer or retailer for more information.

Installation of Li Ion Battery

• Press the dimple on the battery door to release the clip

and slide it off the radio.

• Insert the battery, printed arrows first, into the battery

compartment and press into place.

• Slide and snap the battery door into place.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 8

English

9

Installation of AAA Batteries

• Press the dimple on the battery door to release the clip

and slide it off the radio.

• Insert 3 AAA batteries into the battery tray as shown by

the markings inside the tray.

• Insert the battery tray into the battery compartment and

press into place.

• Slide and snap the battery door into place.

• Press S until A or n flashes (this menu does not appear

if using a Motorola Li Ion battery).

• Press ] or [ to select A for alkaline batteries, or n for

rechargeable AAA cells.

Charging the Battery

Use only the charger supplied with the radio, or other

_ Series power accessories. For optimum battery life,

do not charge the battery for prolonged periods after it is

fully charged. Charging the battery over the weekend is

acceptable.

Using the Drop-in Charger

• Place the charger on a flat surface.

• Insert the jack plug of the power supply into the jack

socket on the charger.

• Plug the power supply into a standard AC wall socket.

• Ensure radio is off. If the radio is on while charging, it will

take longer to fully charge.

• Insert the radio (with battery installed) into the front

section of the charging pocket.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 9

10

English

Note: The radio will fit in the charger with the holster on.

The drop-in charger will also sequentially charge a spare

SNN5571 Li Ion battery. The spare battery will not begin to

charge until the radio battery is fully charged. Both

batteries will charge in approximately 2–6 hours.

Using the Optional Multi Unit Charger

Please contact your dealer or retailer for more information.

The Multi-Unit Charger (MUC) allows drop-in charging of

up to 6 radios or batteries. Batteries can be charged inside

the radios or removed and placed in the MUC separately.

Each of the 6 charging pockets can hold a radio or battery,

but not both.

• Place the charger on a flat surface.

• Insert the jack plug of the power supply into the jack

socket on the MUC.

• Plug the power supply into a standard AC wall socket.

• Ensure radio is off.

• Insert the radio or battery into the charging pocket.

Battery Charging Pocket

Cloning

The cloning feature is available with the MUC. This

enables you to copy your radio's settings to other radios.

Please refer to the user manual supplied with your MUC.

Charging LEDs

On the drop-in charger, the radio and battery charging

pockets have their own LEDs. On the MUC, each of the 6

charging pockets has an LED. The LEDs are grouped into

pairs to show which charging pockets are paired.

The LED is solid red when the battery is charging, and solid

green when charging is complete.

Radio Charging Pocket

?????-CLS446 User Guide 25/9/03 4:11 PM Page 10

English

11

The Battery Meter

The battery meter in the upper left corner of the display

shows how much battery power is remaining.

Battery Type 3 Bars 2 Bars 1 Bar Flashing

dbcm

Li Ion 100%–85% 85%–25% 25%–10% Final 10%

AAA Alkaline 100%–75% 75%–40% 40%–10% Final 10%

Battery Life

The approximate (typical) battery life for:

Li Ion batteries is 12 Hours

AAA Alkaline batteries is 10 Hours

This is based on a 5% transmit, 5% receive and

90% standby cycle

Note: For optimal battery life, high capacity alkaline

batteries are recommended.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 11

12

English

Talking And Listening

Your radio has 8 channels and 121 interference eliminator

codes. If you are in a group and you wish to talk to each

other, all radios must be set to the same channel and

interference eliminator code. If you experience

interference and need to change channel, ensure that you

change the channel of all radios in your group.

Before talking, please remember to monitor the channel,

as described previously. Then press and hold the Push to

Talk (PTT) button. When you are finished talking, release

the PTT button and the radio will beep (if the talk

confirmation tone is enabled). For maximum clarity, hold

the radio 5 to 7 cm away from your mouth and speak

directly into the microphone. Do not cover the microphone

while talking.

Setting the Channel

• Press S until the channel number flashes.

• Press ] or [ to select a channel.

• Press PTT to confirm.

Setting the Code

• Press S until the code number flashes.

• Press ] or [ to select a code.

• Press PTT to confirm.

You can specify a different code for each channel

• To set a channel and code combination, press S and

then press ] or [ to select the channel.

• Press S again and then press ] or [ to select a code.

• Press PTT to exit the menu and to save the channel and

code combination.

Features

Hands Free Use (VOX)

VOX allows you to transmit "hands free" by talking while

using VOX accessories connected to the radio. A VOX

compatible headset is supplied with your radio.

Note: When using audio accessories with your radio, turn

the volume of your radio down before you place the

accessory on your head or in your ear.

To Use The VOX Feature:

• Switch off your radio.

• Open the accessory cover and insert the audio accessory

into the accessory jack. If the VOX icon g is flashing and

you are setting up VOX for the first time, set the VOX

sensitivity level (please see below).

• Switch on your radio. The g icon will appear in the

display to indicate that the VOX feature is active.

• To transmit, speak into the accessory microphone. To

receive, stop talking.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 12

English

13

• Pressing PTT or removing audio accessory will disable

VOX operation.

Note: There is a short delay after you start talking, before

the radio transmits.

Setting Sensitivity Levels

Adjusting your radio’s VOX sensitivity level helps to

minimize the possibility of unintended noises triggering a

transmission, or enhances the ability to pick up quiet

voices.

• With an audio accessory fitted, press S until g and H

show in the display.

• Press ] or [ to select the sensitivity level as follows:

1 - If you speak loudly, or are in a noisy environment.

2 - Suitable for most applications.

3 - If you speak softly, or are in a quiet environment.

• Press PTT to set level.

Call Tones and Vibrate Feature

Your radio can transmit call tones to other radios in your

group so you can alert them that you are about to talk. Your

radio is programmed at the factory with call tones turned

off (set to 0), but you can change this setting to choose a

distinctive call tone.

The vibrate feature is an additional call tone option that

makes your radio vibrate briefly when it receives (if you

have not transmitted or received in the last 30 seconds).

Select call tone 4 to turn the vibrate feature on. i will

show in the display.

To Set the Call Tone

• Press S until E appears in the display.

• Current call tone setting 0-4 will begin to flash.

• Press ] or [ to change and hear call tones while the

setting number is flashing. If you set call tone to 4 you

will feel the radio vibrate as well as hearing the call tone.

• Press PTT to set new call tone.

To transmit your call tone, press B which is on the left

side of the radio.

Scan

Use scan to monitor channels for transmissions, or to find

someone in your group who has accidentally changed

channels.

To Use The Scan Feature:

• Press S. The display shows h and the radio begins to

scan the channels. When the radio detects activity, it

stops on that channel and displays w and the channel

number.

• To talk to the person transmitting without switching

channels, press PTT within 5 seconds. If PTT is not

?????-CLS446 User Guide 25/9/03 4:11 PM Page 13

14

English

pressed within 5 seconds, scanning resumes.

• To stop scanning, briefly press T.

If you press PTT while the radio is scanning, the radio

transmits on the channel you were on before you started

scanning.

Skipping and Scanning

Scan has two temporary features to make it easier to use:

1. Scan advance: If the radio stops scanning on a channel

you do not want to listen to, press ] to resume

scanning for the next active channel.

2. Nuisance delete: Press and hold [ to temporarily

remove a channel from the scan list. The channel

returns the next time you use the scan feature.

Editing the Scan List

For faster scanning and to avoid hearing unwanted

transmissions, you can edit the scan list to skip channels.

• Press S until h displays and the channel number and Y

or n flash.

• Press ] or [ to select the channel you want to remove

from the scan list.

• Press T to display either Y to include the channel or n to

exclude the channel.

• Press PTT to exit.

Voice Scrambling

This feature gives you additional privacy. Anyone who is

listening on the same channel and code will hear distorted

speech, unless they have a voice scrambling code that

matches yours.

• Select the channel on which you wish to set up the voice

scrambling code.

• Press S until e shows in the display.

• Use ] or [ to select the required code. (code 0

disables the voice scrambling code).

• Press PTT to exit.

Microphone Gain

Adjusting your radio’s microphone sensitivity level helps to

minimize the possibility of unintended noises triggering a

transmission, or enhances the ability to pick up quiet

voices.

• Press S until g and ? show in the display.

• Press ] or [ to select the sensitivity level as follows:

1 - If you speak loudly, or are in a noisy environment.

2 - Suitable for most applications.

3 - If you speak softly, or are in a quiet environment.

• Press PTT to set level.

Signal Strength and Channel Busy Indicator

If another radio is transmitting on your set channel and

code w will show in the display and the red LED will flash

?????-CLS446 User Guide 25/9/03 4:11 PM Page 14

English

15

at a faster rate of once per second. The strength of the

received signal will be between 1 (weakest) and 6

(strongest). The icon will also display a strength scale

between v and p. This feature can help determine when

a radio in your group is moving out of range.

Note: Obstacles that block the signal path may affect the

strength of the incoming signal.

Keypad Lock

You can lock the keypad to avoid accidentally changing

your radio settings.

• Press and hold S for 3 seconds.

• To unlock, press and hold S for 3 seconds.

Roger Beep (Talk Confirmation Tone)

When you enable this feature, your two-way radio

transmits a unique tone when you finish transmitting. It’s

like saying 'Roger' or 'Over', and lets others know you’ve

finished talking. Your radio is programmed at the factory

with roger beep turned off.

• To enable the roger beep, press and hold ] as you turn

your radio on.

• When you release the PTT button you will hear the roger

beep.

• To disable the roger beep, press and hold ] as you turn

your radio on.

Time-out Timer

The Time-out Timer feature helps extend battery life by

preventing you from accidentally transmitting. The radio

will emit a continuous warning tone after PTT is pressed

for 60 continuous seconds and will stop transmitting.

Keypad Tones

Every time you press a button on your radio's keypad it

beeps to confirm unless you disable the tones. Your radio

is programmed at the factory with keypad tones turned on.

• To disable the tones, hold down [ while switching on

your radio.

• When you press any button on the keypad you will no

longer hear the tone.

• To enable, again hold down [ while switching on your

radio.

Battery Save Mode

When this feature is disabled (factory default is on) it

improves the attack time, which is the brief period of time

between when the radio receives a transmission and the

sound coming out of the speaker. However this decreases

battery life by approximately 20%.

Restore Factory Defaults

This returns radio to its original factory settings.

Hold down PTT and S while switching on your radio.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 15

16

English

Fitting the Swivel Holster

• Slide the bottom of the radio into the holster until it snaps

into place.

• To remove, push the tab on the holster and pull the radio

away from the holster.

Further Information

Talk Range

Your radio has been designed to maximize performance

and improve transmission range in the field. It is

recommended that you do not use the radios closer than

1.5 meters apart, to avoid interference.

Talk range depends on the terrain. It will be affected by

concrete structures, heavy foliage and by operating radios

indoors or in vehicles.

Optimal Range Outdoors

Flat, open areas

Medium Range Outdoors

Buildings or trees

Also near residential buildings

Minimal Range Outdoors

Dense foliage or mountains

Also inside some buildings

Optimal range occurs in flat, open areas, with up to 3

kilometres of coverage. Medium range occurs when

buildings and trees are in the way. Minimal range occurs

when dense foliage and mountains obstruct the

communication path.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 16

English

17

Troubleshooting

No power • Recharge or replace Li Ion battery.

• Reposition or replace alkaline batteries.

Message not transmitted • Make sure PTT button is completely pressed while you transmit.

• Reposition, replace or recharge batteries.

• Verify the red LED is illuminated while speaking.

• Confirm channel and code settings are correct.

Message not received • Confirm all radios have same channel and code settings.

• Make sure PTT button is not inadvertently being pressed.

• Reposition, replace or recharge batteries.

• Obstructions, and operating indoors or in vehicles may interfere with communication.

Change your location.

• Check to make sure volume is turned up.

• Verify radio is not in scan mode.

Hearing other conversation • Shared channel may be in use, try another.

or noise on a channel

Limited talk range • Steel or concrete structures, heavy foliage and use in buildings and in vehicles will

decrease range. Check for clear line of sight to improve transmission.

• Wearing radio close to body such as in a pocket or on a belt will decrease range.

Change location of radio.

Heavy static or interference • Radios too close. Radios must be at least 1.5 metres apart.

• Radios too far apart. Obstacles interfere with transmission.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 17

18

English

Keypad Locked • Unlock by holding S for 3 seconds.

Low batteries • Recharge or replace batteries. Extreme operating temperatures affect battery life.

Charger light does not come on • Reinsert radio and/or battery.

• Clean battery and/or charger contacts.

• Verify that the charging pin on the transformer is inserted correctly into the drop-in

charger.

• AAA cells installed in radio. Remove and replace with Li Ion battery.

Low battery meter reading • Check radio is set to the correct battery type.

although new batteries • Verify high-capacity alkaline batteries are used for optimal battery life.

are installed

Cannot activate VOX • Feature not set and on.

• Sensitivity set to 0.

• Verify that accessory is VOX compatible.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 18

English

19

Use and Care

To clean radio:

• Use a soft damp cloth

• Do not immerse in water

• Do not use alcohol or cleaning solutions

If your radio gets wet:

• Turn it off and remove batteries

• Dry with soft cloth.

• Battery contacts may be wiped with a dry, lint-free cloth

• Do not use until completely dry

Specifications

Channels 8

Codes 121

Operating Frequency 446.00625-446.09375 MHz

Talk Range Up to 5 kilometres

Power Source Li Ion Battery or 3 AAA

alkaline batteries (with

optional battery tray)

Type Designation CLS446

Transmitter Power (Watts) 0.5 ERP

Modulation Type Phase (Angle)

Channel Spacing (kHz) 12.5

?????-CLS446 User Guide 25/9/03 4:11 PM Page 19

20

English

Warranty Information

How to Get Warranty Service

The authorised Motorola dealer or retailer where you

purchased your Motorola two-way radio and/or original

accessories will honour a warranty claim and/or provide

warranty service.

Please return your radio to your dealer or retailer to claim

your warranty service. Do not return your radio to

Motorola.

In order to be eligible to receive warranty service, you

must present your receipt of purchase or a comparable

substitute proof of purchase bearing the date of purchase.

The two-way radio should also clearly display the serial

number. The warranty will not apply if the type or serial

numbers on the product have been altered, deleted,

removed, or made illegible.

What Is Not Covered By The Warranty

1. Defects or damage resulting from use of the Product in

other than its normal and customary manner or by not

following the instructions in this user manual.

2. Defects or damage from misuse, accident or neglect.

3. Defects of damage from improper testing, operation,

maintenance, adjustment, or any alteration or

modification of any kind.

4. Breakage or damage to aerials unless caused directly by

defects in material or workmanship.

5. Products disassembled or repaired in such a manner as

to adversely affect performance or prevent adequate

inspection and testing to verify any warranty claim.

6. Defects or damage due to range.

7. Defects or damage due to moisture, liquid or spills.

8. All plastic surfaces and all other externally exposed

parts that are scratched or damaged due to normal use.

9. Products rented on a temporary basis.

10. Periodic maintenance and repair or replacement of

parts due to normal usage, wear and tear.

Copyright Information

The Motorola products described in this manual may

include copyrighted Motorola programs, stored

semiconductor memories or other media. Laws in the

United States and other countries preserve for Motorola,

certain exclusive rights for copyrighted computer

programs, including the exclusive right to copy or

reproduce in any form, the copyrighted Motorola

programs.

Accordingly, any copyrighted Motorola computer

programs contained in the Motorola products described in

this manual may not be copied or reproduced in any

manner without express written permission of Motorola.

?????-CLS446 User Guide 25/9/03 4:11 PM Page 20

La pagina sta caricando ...

Motorola CLS446 Manuale utente

Questo manuale è adatto anche per

Motorola CLS446 Manuale utente

in altre lingue

Documenti correlati

Altri documenti