Dedicated Micros 2060 PTZ Dome Manuale del proprietario

MENU SYSTEM MANUAL

HANDLEIDING MENUSYSTEEM

MANUEL D’UTILISATION ET DE PARAMETRAGE

MANUALE DI SISTEMA DEI MENU

MENÚ DEL MANUAL DEL SISTEMA

This product is marked with the CE symbol and indicates

compliance with all applicable directives.

Directive 89/336/EEC.

A “Declaration of Conformity” is held at Dedicated Micros Ltd.,

11 Oak Street, Swinton, Manchester, M27 4FL.

Contents

1. THE DENNARD 2060 DOME CAMERA 3

2. THE DENNARD 2040 DOME CAMERA 5

3. PROGRAMMABLE FEATURES 7

3.1 Preset Positions 7

3.2 Preset Position Titles 7

3.3 Tours 7

3.4 Real Time Clock 7

3.5 Alarm Response 7

3.6 Bottom Flip 8

3.7 Camera Mode 8

3.8 Digital Zoom Extension 8

3.9 Dome Selection Cursor 8

3.10 Text Positioning and Selection 8

3.11 Joystick Range 8

3.12 Host polling 8

3.13 Error Reporting 9

3.14 Activity light 9

3.15 User Timeout 9

3.16 Set Video Amplification 9

3.17 Privacy mode 9

4. OPERATION WITH A CONTROL PANEL 10

4.1 Dome Menu Structure with Dennard controllers 10

4.2 Main Menu 11

4.2.1 Go to Preset or Start Tour 11

4.2.2 PIN number entry 12

4.3 Supervisor Menu 15

4.3.1 Store/Edit Preset 15

4.3.2 Store/Edit Tour 16

4.3.3 Alarm Setup 17

Dennard 2040 / 2060 Menu System Manual Page. 1

4.3.4 Supervisor Options 19

4.3.5 Enter New PIN 22

4.3.6 Privacy Zone Setup 22

4.4 Technician Menu 23

4.4.1 Camera set up 23

4.4.2 Enable/Disable options 24

4.4.3 Joystick control 24

4.4.4 Miscellaneous Services 25

4.4.5 Enter New PIN 26

5. MENU FLOW CHART 27

6. ALTERNATIVE CONTROLLERS 31

6.1 Dedicated Micros Digital Sprite 2 31

6.1.1 Up the coax control 31

6.1.2 RS485 control 32

6.2 Baxall / Vista controllers 32

6.3 Dennard dtx1000/dc 33

6.4 Building Block Video TX1000/DC 34

6.5 Dennard dtx400/dc 35

6.6 Building Block Video TX400DC 36

7 TROUBLE SHOOTING GUIDE 37

Dennard 2040 / 2060 Menu System Manual Page. 2

1. THE DENNARD 2060 DOME CAMERA

The Dennard 2060 Dome Camera is a precision unit, offering a wide variable speed range, together

with a large pre-set memory for positions, tours and alarm responses. It has a switchable

colour/monochrome camera (colour-only on indoor units) with an 18:1 or 26:1 zoom lens plus x 4

digital enhancement.

The unit has a comprehensive set of features as standard, which can be tailored for individual

preferences. These can be accessed through an internally generated set of menus overlaid on the

video signal if the controller does not have a suitable layout. Each Dome Camera is delivered with a

separate weatherproof power supply.

Outline Specification:

Dennard 2040 / 2060 Menu System Manual Page. 3

Speed range 0.05 to 300° / second max (both Pan and Tilt)

Repeatability 5 minutes of arc

Control

RS 485 half duplex or simplex, 9600 Baud OR ‘Up the coax’ using

built in DEN PANEL or BAX PANEL protocol converter for Dennard,

BBV & DM or Baxall controls

Storage capacity

200 positions, with identifying title of up to 20 characters

100 tours of up to 16 preset positions

100 deep alarm response memory

Power Supply

24Va.c, Camera & control electronics:-10VA

Heater & blower unit:-10VA

Dimensions

Dome Camera: 150mm diameter hemisphere x 230mm overall

Power Supply: 165L x 135W x 95H.

Protection BS EN 60529 to level IP66 (no water ingress)

Weight

Dome Camera: 1.7 kg + mounting bracket

Power Supply: 1.3 kg

Mounting Configurations

Ceiling mount, pendant mount, wall bracket, corner mount, snowdrop

& tile mounts available

18X zoom camera module

26X zoom camera module

Dennard 2040 / 2060 Menu System Manual Page. 4

Optical range

4.1mm to 73.8mm zoom; F1.4 to F3.0

Auto-focus with manual override

Privacy zones 24 programmable zones (8 on screen at any time)

Video sensitivity 0.7 lux colour

Video resolution

768 horizontal x 494 vertical pixels

More than 470 TVL

Video output 1.0v p-p composite, negative synch

Optical range

3.5mm to 91.0mm zoom; F1.6 to F3.8

Auto-focus with manual override

Privacy zones 24 programmable zones (8 on screen at any time)

Video sensitivity 1.0 lux colour

Video resolution

768 horizontal x 494 vertical pixels

More than 470 TVL

Video output 1.0v p-p composite, negative synch

2. THE DENNARD 2040 DOME CAMERA

The Dennard 2040 Dome Camera is a precision indoor unit, offering a wide variable speed range,

together with a large pre-set memory for positions, tours and alarm responses. It has a colour

camera with a 18:1 zoom lens.

The unit has a comprehensive set of features as standard, which can be tailored for individual

preferences. These can be accessed through an internally generated set of menus overlaid on the

video signal if the controller does not have a suitable layout.

Outline Specification:

Dennard 2040 / 2060 Menu System Manual Page. 5

Speed range 0.05 to 300° / second max (both Pan and Tilt)

Repeatability 5 minutes of arc

Control

RS 485 half duplex or simplex, 9600 Baud OR 'Up the coax' using

built in DEN PANEL or BAX PANEL protocol converter for Dennard,

BBV & DM or Baxall controls

Storage capacity

100 positions with identifying title of up to 20 characters

50 tours of up to 16 preset positions

50 alarm responses

Power Supply 24Va.c, camera & control electronics; 10VA

Dimensions

150mm diameter hemisphere with 220mm ceiling ring

110mm height behind ceiling panel

Weight 1.5 kg

Mounting Configurations Tile mount.

18X zoom camera

Dennard 2040 / 2060 Menu System Manual Page. 6

Optical range

4.1mm to 73.8mm optical zoom; F1.4 to F3.0

Auto focus with manual override

Privacy zones 24 programmable zones with 8 on screen at any time

Video sensitivity 3 Lux colour

Video resolution

768 horizontal x 494 vertical pixels

More than 470 TVL

Video output 1.0v p-p composite, negative sync

3. PROGRAMMABLE FEATURES

The Dennard 2040 / 2060 Camera's have a number of features which can be selected by the

System Supervisor when the dome is installed. Any of these can be altered subsequently, or

cancelled altogether, to give the best operational responses for any particular application. They are

invoked or cancelled through on-screen menu structures, described in section 4, and the settings

are then retained in non-volatile memory so that they are not affected by a loss of power.

The features, and what they offer, are described below:

3.1 Preset Positions

Up to 200 (Dennard 2060) or 100 (Dennard 2040) positions can be stored and recalled at any time.

Each position stores the Pan, Tilt, Zoom, and Focus positions as well as the position title.

3.2 Preset Position Titles

Each preset position title can have up to 20 alphanumeric characters to identify the associated

position uniquely. The default title position lies at the top left hand corner of the video picture, left

justified, but this can be altered if required.

The preset position titles only appear at the position they identify: any movement from that position

will remove them.

3.3 Tours

Up to 100 (Dennard 2060) or 50 (Dennard 2040) tours can be stored and recalled at any time.

Each tour can contain up to 16 positions together with a ‘Dwell’ time at each position plus the

‘Travel Time’ that the dome unit must take to reach the next position. When the last position in the

tour is reached, the tour ‘loops’ back to the first position.

3.4 Real Time Clock (Not applicable to the Dennard 2040)

The Dennard 2060 dome camera is fitted with a real time clock to provide time and date marks for

the operator and the recording system if required. A range of selectable formats can provide time

and date displays and the unit is able to use the information to provide enhanced alarm functions

where the reaction to an alarm can be modified depending on the time of day or the day of the

week.

3.5 Alarm Response

Up to 100 (Dennard 2060) or 50 (Dennard 2040) Alarm responses can be stored. Each alarm

response creates a specified reaction to an alarm number. This is a very powerful feature, allowing

a number of domes, or any other device conforming to the Dennard protocol, to invoke a pre-set

alarm action from one single loop broadcast command.

Dennard 2040 / 2060 Menu System Manual Page. 7

3.6 Bottom Flip

The dome will automatically pan through 180 degrees as fast as possible when tilted fully down so

that it is possible to follow a person or car, moving directly underneath the dome, with only a single

joystick direction to consider.

3.7 Camera Mode

The camera in both Dennard 2060 and Dennard 2040 can be switched between colour and

monochrome mode. In the Dennard 2060 it can be selected as colour/mono in which case it will

automatically switch to mono when the light level is insufficient for good quality colour pictures.

3.8 Digital Zoom Extension

The camera system allows an extension of the optical zoom by selecting more of the central part of

the picture and expanding this to fill the frame. This feature is selectable.

3.9 Dome Selection Cursor

The menu structure itself, and the choices and selections offered, are searched and invoked by a

single cursor or flashing character and the direction in which this moves depends on the particular

control panel in use. The direction of movement can be reversed separately for horizontal and

vertical movement if required.

3.10 Text Positioning and Selection

All text can be positioned where it is wanted, replaced with default text (eg: Position 31, or Sector

18), or removed as required.

3.11 Joystick Range

Even if the control panel has a wide range proportional joystick output, the dome has such a wide

speed range that both a fast and a slow speed range are needed to realise the full performance

(provided of course that the control panel in question has a facility to invoke these separately).

The slow speed range is simply the same as the fast speed range following the same in-built

correlation law, but divided by a constant. This constant can be set between 2 and 128.

3.12 Host polling

When the dome is configured for communication using RS485 protocols it can be set to check its

communication link at regular intervals. If a continuous data stream is expected from the controller,

enabling Host Polling will get the dome to report a communications error if nothing is received for 5

seconds. Normally, this setting is disabled.

Dennard 2040 / 2060 Menu System Manual Page. 8

3.13 Error Reporting

The dome constantly monitors its own health and is able to indicate that a problem has occurred by

a flashing square in the top right hand corner of the transmitted picture. The cause can

subsequently be requested when convenient. Alternatively, the unit can display the error text

instead of the flashing square.

3.14 Activity light

A green LED provides some diagnostic help when first switching the dome on and also indicates

when command signals are received. As it may be visible externally it can be switched on or off.

3.15 User Timeout

There is a possibility that the dome may be left pointing at an unhelpful scene and, for whatever

reason, ‘forgotten’. To cater for this eventuality, two settings have the specific function of acting to

prevent this happening. These are Preset 001 and Tour 001.

A time delay can be set between 1 and 999 seconds and a default response to the timeout being

reached also defined. If the time is exceeded after any joystick/key entry Pan and Tilt input at the

Control Panel then the default action will occur.

If a delay time of 0 is set, no default action will occur and the unit will wait indefinitely for the next

user input.

If a dome menu screen is left waiting for an input for more than 3 minutes then the system times

out and the dome resumes its previous activity.

3.16 Set Video Amplification

This facility allows the video gain to be adjusted from the normal setting, with four levels available.

Video lift can be tuned on or off and is normally set to the Off position.

3.17 Privacy mode

It is sometimes desirable to prevent operators from viewing certain areas. To meet this requirement

the Privacy mode allows black patches to be set up to cover these areas.

The size of the patch overlaid is the size of the monitor view at whatever zoom setting is used.

When zooming out, the patch reduces in size so that it only covers the original area.

Dennard 2040 / 2060 Menu System Manual Page. 9

4. OPERATION WITH A CONTROL PANEL

NB: This will vary between control panels. Please refer to the Controller manual.

The Dome Camera's are open protocol devices. Consequently, there are several different

manufacturers’ controllers available to drive it. All of the many features offered by the dome are

programmed from one of three menu structures. Each controller will have individual control

configurations which make it essential that the user reads the controller manual to ascertain which

button activation gives access to the menu features. Section 6 gives these functions for several

popular controllers.

The following instructions will guide you through the menu structure when using the Dome & PSU

(with address set to No. 253… DEN PANEL) controlled by either a Dennard dtx400dc or dtx1000dc

4.1 Dome Menu Structure with Dennard controllers

The Menus appear on the screen when activated by the following commands:

Note that the ‘shift’ key must be held down while the selection is made.

On activation, the menu will appear on the monitor screen against the normal video scene

background with a cursor on the left hand edge. A choice is made by positioning the cursor over the

desired feature and operating an “ACCEPT” button(s) which, for the Dennard controllers, is as

follows:-

For Dennard dtx1000dc, hold the preset button and press CAMERA SELECT 1

For Dennard dtx 400dc, press preset 1 button

Dennard 2040 / 2060 Menu System Manual Page. 10

Dennard dtx1000dc

access

Dennard dtx400dc

access

User Menu shift wash shift 1

Supervisor Menu (password required) shift wipe shift 2

Technicians Menu (password required) shift autopan shift 3

4.2 Main Menu

When called, the Main Menu screen will display the following options, against a camera display

background, with a cursor at the left hand edge:

Using the joystick, or direction arrow keys, move up or down the list to select the feature required

then press the appropriate key(s) to accept/select it. If ‘Exit’ is chosen the menu is cleared and no

other action is taken by the dome.

4.2.1 Go to Preset or Start Tour

These selections allow the operator to recall the full range of stored Preset positions and Tours,

even if the control panel has neither the numerical range nor general ability to do so.

Note that this screen only allows existing preset positions and tours to be accessed. To set

up new presets or tours, see section 4.3.1 or 4.3.2

The display will prompt for the required numerical entry with the following subsidiary menu:

The cursor can be moved across the numerical line, using the joystick or control buttons, until the

desired number is reached. The characters will flash their position in turn and, as soon as one is

selected with the ACCEPT button(s), will be displayed in the _ _ _ part of the display.

Leading zeros need not be entered (eg 001 may be entered simply as ‘1’) but the entry must be

within range, eg 001 - 250 for Presets and 001 - 100 for Tours (Dennard 2060) and 001 - 100 for

Presets and 001 - 50 for Tours (Dennard 2040). Entries outside the range will cause an ‘Illegal

Entry’ message to flash, and the entry must be cleared and re-entered.

When the digits have been selected, Accept Entry will invoke that choice and the screen will

automatically clear to the desired camera position.

Dennard 2040 / 2060 Menu System Manual Page. 11

Go to Preset

Start Tour

Technician Menu

Supervisor Menu

Exit

Preset Number___ (orTourNumber)

0123456789

Accept Entry

Clear Entry

Return

To change the choice, ‘Clear Entry’ will start the process again.

Note that Preset number 1 and Tour number 1 should be allocated to the most common or

important views. These values are the ones to which the dome automatically returns

following a power cut if no operator is in attendance. See the section on power fail, sec

4.4.2.

4.2.2 PIN number entry

When the Technician or Supervisor menu is called the following screen appears. The password

or PIN Number is keyed in using the same method as used with previous entries.

The cursor is run across the numerical line, using the joystick or control buttons, until the desired

number is reached. The characters will flash their position in turn and as soon as one is selected

with the ACCEPT button(s) it will be displayed in the _ _ _ _ part of the display.

When all four digits have been selected, Accept Entry will invoke that choice and the screen will

automatically change to the selected menu i.e. the Technician or Supervisor menu.

Dennard 2040 / 2060 Menu System Manual Page. 12

Enter PIN____

0123456789

Accept Entry

Clear Entry

Cancel

THE FACTORY SET PASSWORDS (PINs), WHICH CAN BE

CHANGED BY THE TECHNICIAN OR SUPERVISOR IN THEIR

RESPECTIVE MENUS, ARE PRINTED BELOW.

TO PREVENT UNAUTHORISED CHANGES BEING MADE TO

SETTINGS OR STORED CAMERA POSITIONS, IT IS ADVISED

THAT PIN NUMBERS ARE KEPT IN A SAFE PLACE.

IF IT IS FELT NECESSARY, CUT THIS PAGE OUT OF THE

MANUAL.

Dennard 2040 / 2060 Menu System Manual Page. 13

To gain access to the Supervisor Menu, enter PIN as ‘1111’

To gain access to the Technician Menu, enter PIN ‘9999’

THIS PAGE IS INTENTIONALLY LEFT BLANK

Dennard 2040 / 2060 Menu System Manual Page. 14

4.3 Supervisor Menu

The SUPERVISOR MENU allows the supervisor not only to duplicate the operator menu functions,

but also to programme Preset positions (with their identifying title) and Tours. Additionally, cursor

setting and text positioning and selection are accessed here.

The functions are split into a series of underlying menus in ‘layers’. When returning from most

underlying menus, the overlying menu is re-presented. The functions which are less likely to be

needed lie deeper in the structure.

The Supervisor Menu displays:

4.3.1 Store/Edit Preset

The first option enables the supervisor to define a view (including pan, tilt and zoom settings) and

store it for future recall. Note that storing a Preset requires that the desired camera view is already

visible when this screen is entered. Selecting this option calls up the following underlying screens.

Selecting the preset number is achieved as with the previous numerical entry screens. When the

number is accepted, a new display will allow the supervisor to give this position a name (such as

‘Main Gate’ or ‘Front Door’) or use the default names stored in the dome software. The screen will

prompt with:

Edit Preset Text -

Yes

No

Preset Number___

0123456789

Accept Entry

Clear Entry

Return Without Change

Delete Preset

Store/Edit Preset

Store/Edit Tour

Alarm Setup

Supervisor Options

Change PIN

Privacy Zone Setup

Return

Exit

Dennard 2040 / 2060 Menu System Manual Page. 15

Select ‘No’ to use the default names or ‘Yes’ to enter a new name through the following screen.

The title choice is made as usual with the cursor and accepted when ready (which will store the

chosen Title with the stored Preset position). Backspace allows a correction to be made while

‘Return without change’ will store the Preset position with the default title. The title appears in the _

_ space as it is compiled.

Note that the ‘_’ symbols indicate where the title will appear - they do not appear on-screen

4.3.2 Store/Edit Tour

A Tour is a predefined journey taken by the camera, between a number of Preset positions. Before

accessing this facility, ensure that all the required Preset positions have been stored, as shown in

section 4.3.1. Choosing to program a Tour first requires the Tour Number to be entered in an

identical procedure to selecting a Position (except that the range must lie between 001 and 100).

Once the number has been accepted, a subsidiary menu is displayed:

If a tour has already been established on this number its initial data is displayed as ‘Old’. This data

can be edited by adding new values or a new tour can be established.

Here the entry format follows the now-familiar procedure but the _ _ _ characters have specific

functions: The first three characters, PPP, represent a Preset position number. ‘DD’ is the dwell

time that the camera must spend stationary at that position and ‘SS’ represents the time that the

camera must take to reach the next position in the tour. The times are entered as seconds,

between 01 and 99. If no value is entered, the Tour will use the default values of 2 seconds dwell

time and 3 seconds travel time.

When all characters are completed and then accepted, the display clears the entry ready to receive

the next position information and the ‘Item’ counter is incremented. When all entries are complete,

select the ‘Store Tour’ instruction.

Dennard 2040 / 2060 Menu System Manual Page. 16

ABCDEFGHIJKLMNOPQRSTUVWX

YZabcdefghijklmnopqrstuv

wxyz0123456789:/*=+.-

Backspace

Return Without Change

Accept Entry

____________

Item ___intour___

PPPDDTT

Old_______

New_______

0123456789

Accept Entry

Clear Entry

Return Without Change

Store Tour

4.3.3 Alarm Setup

Alarms are inputs into the dome which require the dome to undertake a specific action. They may

come from a number of external sources, such as door entry systems or PIR motion sensors. The

Dennard 2060 dome has a clock function that enables the supervisor to select different actions

depending on the time of day or the day of the week. This clock function is not available in the

Dennard 2040, go to section 4.3.3.1. The Alarm Setup screen provides access to three options:

4.3.3.1 Alarm Action Setup

On selecting this function the supervisor must select an alarm number in the usual way with the

following screen:

Accepting the Alarm number brings up the following screen:

This allows a specified preset position P or tour T to be stored, along with its identification number

‘nnn’ which will be implemented when the alarm is activated. To select an option, use the code ‘01’

for Tour or ‘10’ for Preset (the 1 under the P or T selects its use; 11 is invalid). Accepting the entry

will increment the alarm number allowing all inputs to have an action allocated to them or their

existing action, shown as ‘Old’, modified. The alarm action will be sustained for a duration set by

the user timeout (see section 4.3.4.1).

Dennard 2040 / 2060 Menu System Manual Page. 17

Alarm Action Setup

Mask Alarm

Select Holidays

Return

Exit

Alarm Number___

01234567890

Accept Entry

Clear Entry

Return Without Change

Delete Alarm

Alm___Select P or T

PTnnn

Old____

New____

0123456789

Accept Entry

Clear Entry

Return Without Change

(This screen is not applicable to Dennard 2040)

4.3.3.2 Mask Alarms (Not Applicable to Dennard 2040)

Alarm responses can be modified, depending on when they are activated. Selecting this facility will

bring up the following screen:

The letters displayed indicate:

MTWTFSS Monday to Sunday

H Holiday

hhmm Time of ‘Mask On’

hhmm Time of ‘Mask Off’

Entering a ‘1’ under a day of the week means that the alarms will be masked – i.e. they will not

cause a response from the dome – on that day. Similarly, a ‘1’ under the Holiday means that the

alarm is masked on specified holidays (note that the setting for a holiday will override the setting for

a day of the week). The mask will operate throughout the days selected unless a mask on and off

time are entered. This is achieved through numerical entry of the time using the 24hr clock. The

mask temporarily disables all connected alarms.

For example, if motion sensors have been connected into the dome but are only required to

operate outside of normal working hours they can be masked by entering the code

‘1111100008301800’. This masks the alarms on Mon – Fri between 08.30 a.m and 6 p.m. Outside

these times, and at the weekends and on holidays, the dome will respond to the alarms as desired.

To add complete flexibility, up to ten levels of configuration are available, indicated by the ‘Item

number’ on the screen. As each entry is accepted the number increments until the full action is

saved. Secondary levels allow different masking times to be selected on different days. In the

example above, it may be that the building closes early on Friday. To achieve the different times,

the first code (item) would be modified to ‘1111000008301800’ and a second item code entered as

‘0000100008301400’. Now, the first mask only applies from Monday to Thursday while the second

level masks the alarms on Fridays, between 8.30 a.m. and 2 p.m. More complex masks can be built

up using the same logic for more variations.

4.3.3.3 Select Holidays (Not Applicable to Dennard 2040)

Up to 15 days can be programmed in as holidays, to cover periods such as Christmas or Bank

Holidays, when the alarm action may require modification. When the option is selected the following

screen is displayed:

Dennard 2040 / 2060 Menu System Manual Page. 18

Item___ofAlarm Mask

PTWTFSSHhhmmhhmm

Old______________

New____

0123456789

Accept Entry

Clear Entry

Return Without Change

Save and Return

__________

La pagina si sta caricando...

Dedicated Micros 2060 PTZ Dome Manuale del proprietario

Questo manuale è adatto anche per

Dedicated Micros 2060 PTZ Dome Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti