Moog Videolarm PFD7TS-3 Manuale utente
- Categoria
- Accessori per telecamere di sicurezza
- Tipo
- Manuale utente
www.videolarm.com
PFD7CN-3
SView™ Outdoor Pressurized FusionDome
Installation and Operation Instructions for the following models:
PFD7CN-3 IP Network Ready 7” Pressurized Outdoor PTZ
Camera System with 36x zoom compression, full D1.
Clear dome, with 24Vac input, heater/ blower
PFD7CS-3 (Analog version)
IP Network Ready 7” Pressurized Outdoor PTZ Camera
System with 36x zoom compression, full D1. Clear dome,
with 24Vac input, heater/ blower
Before attempting to connect or operate this product, please read these
instructions completely. To be used with the 81-IN5409 Instruction Manual.
CERTIFIED
81-IN5382
01-15-2009
© 2009, Videolarm, Inc. All Rights Reserved
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
UNPACKING
SERVICE
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with damp cloth.
7 Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8 Cable Runs- All cable runs must be within permissible distance.
9 Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the
unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the
integrity of the installation is intact. Failure to comply with the foregoing could result in the
unit separating from the support structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make
future shipments of the equipment.
2 These Installation and Operating Instructions.
If technical support or service is needed, contact us
at the following number:
The lightning flash with an arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of non-insulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk
to persons.
Este símbolo se piensa para alertar al usuario a la
presencia del “voltaje peligroso no-aisIado” dentro del
recinto de los productos que puede ser un riesgo de
choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la
presence “de la tension dangereuse” non-isolée dans la
clôture de produits qui peut être un risque de choc
électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença
“di tensão perigosa non-isolada” dentro do cerco dos
produtos que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla
presenza “di tensione pericolosa” non-isolata all’interno
della recinzione dei prodotti che può essere un rischio di
scossa elettrica
.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones
importantes en la literatura que acompaña la
aplicación.
Ce symbole de point d’exclamation est prévu pour
alerter l’utilisateur à la presence des instructions
importantes dans la littérature accompagnant
l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der
Literatur alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido
alertar o usuário à presença de instruções importantes
na literatura que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti
nella letteratura che accompagna l'apparecchio.
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1- 800 - 554 -1124
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICE-
ABLE PARTS INSIDE. REFER SEVICING TO
QUALIFIED SERVICE PERSONNEL.
LIMITEDWARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARMINC. warrantsthis Productto be free from defectsin materialor workmanship,as follows:
PRODUCTCATEGORY PARTS LABOR
All Enclosures and Electronics Five (5) Years Five (5) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years
Controllers Five (5) Years Five (5) Years
Power Supplies Five (5) Years Five (5) Years
Accessory Brackets Five (5) Years Five (5) Years
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc.
Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package
an equal degree of protection with a
RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide
Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.
1.NOTIFICATIONOF CLAIMS: WARRANTYSERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice
with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the
warranty period. If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall p
ay Videolarm
for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall
extend the warranty period as to the entire Product. The
warranty on the repaired part only shall be in for a period of ninety (90) days
following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.
2.EXCLUSIVE REMEDY: ACCEPTANCE:Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3.EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service
during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts
of God (i.e., hurricanes, earthquakes),
failure of the end-user to follow the directions outlined in the product instructions, failure of the
end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,
or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is
for regular
replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by
personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original
(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold
AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying
documentation furnished with, or as part of the Product is furnished “AS IS”(i.e., without any warranty of any kind), except where expressly provided
otherwise in any documentation or license agreement furnished with the Product.
4.PROOF OF PURCHASE:The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMEROF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH
REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMME
RCIAL CODE AND/OR IN ANY OTHER COMPARABLE
STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM
PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE
PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
/tour operation
/tour operation
**6 months if used in autoscan
/tour operation
**6 months if used in autoscan
/tour operation
SView Series Five (5) Years
Five (5) Years
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
TERMS AND CONDITIONS
24 VAC
3.3 Amps
Total Power: 80 Watts
Accessories: Heater: 50 Watts/Blower: 2 Watts
Camera Power: 28 Watts
Tools Required: .100” Flat Head Screwdriver
Phillips Head Screwdriver
7/16” Wrench or Socket
24 VAC
3.3 amperios
Energía Total: 80 vatios
Accesorios: Calentador: 50 Watts/Blower: 2 vatio
Energía De la Cámara fotográfica: 28 vatios
Las Herramientas Requirieron: Destornillador Principal Plano Del 100"
Destornillador Principal Phillips
24 VCA
3.3 ampères
Puissance Totale : 80 watts
Accessoires : Réchauffeur : 50 Watts/Blower : 2 watts
Puissance D'Appareil-photo : 28 watts
Les Outils besoin : Tournevis Principal Plat De 100"
Tournevis Principal Phillips
24 VAC
3.3 Ampere
Gesamtenergie: 80 Watt
Zusatzgeräte: Heizung: 50 Watt/Blower: 2 Watt
Kamera-Energie: 28 Watt
Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher
Kreuzkopfhauptschraubenzieher
24 VAC
3.3 ampères
Poder Total: 80 watts
Acessórios: Calefator: 50 Watts/Blower: 2 watt
Poder Da Câmera: 28 watt
As Ferramentas Requereram: Chave de fenda Principal Lisa Do 100"
Chave de fenda Principal Phillips
24 VAC
3.3 ampère
Alimentazione Totale: 80 watt
Accessori: Riscaldatore: 50 Watts/Blower: 2 watt
Alimentazione Della Macchina fotografica: 28 watt
Attrezzi Richiesti: Cacciavite Capo Piano Del 100"
Cacciavite Capo "phillips"
Electrical Specifications
Power 24VAC
Class 2 Only
!!
PFD7CN-9
PFD7CS-9
Français
Deutsch
Italiano
Portuguese
Español
English
Contents of Box
*** Pan Tilt boxed separately along with its instructions.
1
Securely mount bracket to wall. Pull wiring
through bracket and position grommet as shown.
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
4
Screw the (2) bolts into the coupling.
• Atornille (2) los pernos en el acoplador.
• Vissez (2) les boulons dans l'accouplement.
• Schrauben Sie die (2) Schraubbolzen in die Koppe-
lung.
• Parafuse (2) os parafusos no acoplamento.
• Avviti (2) i bulloni nell'accoppiamento.
2
Wrap Teflon tape around the pipe threads
to ensure a tight seal.
• La cinta del Teflon del abrigo alrededor de la pipa rosca
para asegurar un sello apretado.
• La bande de teflon d'enveloppe autour de la pipe filète
pour assurer un joint serré.
• Verpackung Teflonklebeband um das Rohr verlegt, um
eine feste Dichtung sicherzustellen.
• A fita adesiva do Teflon do envoltório em torno da
tubulação enfía para assegurar um selo apertado.
• Il nastro del Teflon dell'involucro intorno al tubo filetta per
accertare una guarnizione stretta.
TM
3
Screw the coupling onto the pipe threads
until it is hand tight.
• Atornille el acoplador sobre los hilos de rosca de la pipa
hasta que es mano firmemente.
• Vissez le couplage sur les fils de pipe jusqu'à ce que ce
soit main fortement.
• Schrauben Sie die Koppelung auf die Rohrgewinde, bis
es Hand fest ist.
• Parafuse o acoplamento nas linhas da tubulação até
que esteja mão firmemente.
• Avviti l'accoppiamento sui filetti del tubo fino a che non
sia fortemente mano.
SOLD SEPARATELY
SOLD SEPARATELY
SOLD SEPARATELY
SOLD SEPARATELY
5
Loop the lanyard over the set screw to
temporarily hold housing.
• Coloque el acollador sobre el tornillo de presión para
celebrar temporalmente la cubierta.
• Faites une boucle la lanière au-dessus de la vis de réglage
pour tenir temporairement le logement.
• Schlingen Sie die Abzuglinie über der Klemmschraube, um
Gehäuse vorübergehend zu halten.
• Dê laços no colhedor sobre o parafuso de fixação para
prender temporariamente a carcaça.
• Colleghi la cordicella in circuito sopra la vite di arresto
temporaneamente per tenere l'alloggiamento.
6
Make the appropriate wiring connections
from the dome to the gooseneck.
• Haga las conexiones apropiadas del cableado de la bóveda
al gooseneck.
• Établissez les rapports appropriés de câblage à partir du dôme
au col de cygne.
• Stellen Sie die passenden Verdrahtung Beziehungen von der
Haube zum gooseneck her.
• Faça as conexões apropriadas da fiação da abóbada ao
gooseneck.
• Faccia i collegamenti adatti dei collegamenti dalla cupola al
gooseneck.
7
Undo the lanyard, pull housing up and twist
secure with the locking bolt and washers.
• Deshaga el acollador, tire de contener para arriba y tuerza seguro
con el perno y las arandelas de fijación.
• Défaites la lanière, tirez loger vers le haut et tordez bloqué avec le
boulon et les rondelles de fermeture.
• Annulieren Sie die Abzuglinie, ziehen Sie oben unterbringen und
verdrehen Sie sicheres mit dem verriegelnschraubbolzen und den
Unterlegscheiben.
• Undo o colhedor, puxe abrigar acima e torça seguro com o
parafuso e as arruelas travando.
• Undo la cordicella, tiri l'alloggio in su e torca sicuro con il bullone e
le rondelle di bloccaggio.
8
Slide the grommet down over the coupling to prevent
water from entering and complete the assembly.
• Resbale el ojal abajo sobre el acoplador para evitar que el agua
entre y para terminar a la asamblea.
• Glissez le canon isolant vers le bas au-dessus de l'accouplement
pour empêcher l'eau d'entrer et pour accomplir l'assemblée.
• Schieben Sie die Gummimuffe unten über der Koppelung, um zu
verhindern, daß Wasser und die Versammlung durchzuführen
hereinkommt.
• Deslize o ilhó para baixo sobre o acoplamento para impedir que a
água entre e para terminar o conjunto.
• Faccia scorrere il gommino di protezione giù sopra l'accoppiamento
per impedire l'acqua entrare e per completare il complessivo.
SOLD SEPARATELY
SOLD SEPARATELY
SOLD SEPARATELY
SOLD SEPARATELY
RJ45
RJ45
24VAC
1
2
Camera/Heater/Blower
Camera/Heater/Blower
Yellow
Green
SNC-RZ50/SNC-RZ30
28 Watts
52 Watts
1/0
1
2
Alarm 1
Common
Blue
Violet
A
B
C
D
Wire as shown below for IP
models:(PFD7CN-9; PFD7TN-9)
Make the appropriate male and female connec-
tions. Indoor model does not include pre-run cables.
• Haga las conexiones masculinas y femeninas apropiadas. El
modelo de interior no incluye pre-funciona los cables.
• Établissez les rapports masculins et femelles appropriés. Le
modèle d'intérieur n'inclut pas pré-courent des câbles.
• Stellen Sie die passenden männlichen und weiblichen
Beziehungen her. Innenmodell schließt nicht vor-laufen lassen
Kabel ein.
• Faça as conexões masculinas e fêmeas apropriadas. O
modelo indoor não inclui pre-funciona cabos.
• Faccia i collegamenti maschii e femminili adatti. Il modello
dell'interno non include pre-fa funzionare i cavi.
MM
2
AWG
,5 ,75 1,0 1,5 2,5 4 6
22 20 18 16 14 12 10
The beam angle may be adjusted on the
bottom of the unit.
• Éstos se recomiendan las distancias máximas para
24VAC con una gota del voltage del 10%.
• Ceux-ci sont recommandés des distances maximum
pour 24VAC avec une chute de tension de 10%.
• Diese werden maximale Abstände für 24VAC mit
einem 10% Spannungsabfall empfohlen.
• Estes são recomendados distâncias máximas para
24VAC com uma queda de tensão de 10%.
• Questi sono suggeriti distanze massime per 24VAC
con una differenza de potenziale di 10%.
12
These are recommended maximum distances
for 24VAC with a 10% voltage drop.
Remove Pan/Tilt from shipping carton.
Install in base bracket in housing.
• Quite Pan/Tilt del cartón del envío. Instale en soporte
bajo en la cubierta.
• Enlevez Pan/Tilt du carton d'expédition. Installez dans
la parenthèse basse dans le logement.
• Entfernen Sie Pan/Tilt vom Verschiffenkarton. Bringen
Sie in niedrigen Haltewinkel im Gehäuse an.
• Remova Pan/Tilt da caixa do transporte. Instale no
suporte baixo na carcaça.
• Rimuova Pan/Tilt dalla scatola di trasporto. Installi in
staffa bassa in alloggiamento.
A
B
C
D
RJ45
RJ45
24VAC
1
2
Camera/Heater/Blower
Camera/Heater/Blower
Yellow
Green
SNC-RZ50/SNC-RZ30
13 Watts
52 Watts
1/0
1
2
3
4
RS-485RX A
RS-485RX B
RS-485TX A
RS-485TX B
Blue
Violet
Gray
White
Make the appropriate male and female connec-
tions. Indoor model does not include pre-run cables.
• Haga las conexiones masculinas y femeninas apropiadas. El
modelo de interior no incluye pre-funciona los cables.
• Établissez les rapports masculins et femelles appropriés. Le
modèle d'intérieur n'inclut pas pré-courent des câbles.
• Stellen Sie die passenden männlichen und weiblichen
Beziehungen her. Innenmodell schließt nicht vor-laufen lassen
Kabel ein.
• Faça as conexões masculinas e fêmeas apropriadas. O
modelo indoor não inclui pre-funciona cabos.
• Faccia i collegamenti maschii e femminili adatti. Il modello
dell'interno non include pre-fa funzionare i cavi.
Wire as shown below for analog
models: (PFD7CS-9; PFD7TS-9)
11
10
9
12
To install the dome align the tabs and twist
counter clockwise to secure.
• Para instalar la bóveda alinee las lengüetas y tuerza al revés
a la derecha para asegurar.
• Pour installer le dôme alignez les étiquettes et tordez contre
dans le sens des aiguilles d'une montre pour fixer.
• Um die Haube anzubringen richten Sie die Vorsprünge aus
und verdrehen Sie sich entgegengesetzt nach rechts um zu
sichern.
• Para instalar a abóbada alinhe as abas e torça-as contra no
sentido horário para fixar-se.
• Per installare la cupola allinei le linguette e torca contro in
senso orario per fissare.
Hand tighten the screws on the dome.
Recommended torque 12 inches/lb (1.35Nm).
• La mano aprieta los tornillos en la bóveda. Esfuerzo de
torsión recomendado 12 inches/lb (el 1.35Nm).
• La main serrent les vis sur le dôme. Couple recom-
mandé 12 inches/lb (1.35Nm).
• Hand ziehen die Schrauben an der Haube fest.
Empfohlene Drehkraft 12 inches/lb (1.35Nm).
• A mão aperta os parafusos na abóbada. Torque
recomendado 12 inches/lb (1.35Nm).
• La mano stringe le viti sulla cupola. Coppia di torsione
suggerita 12 inches/lb (1.35Nm).
When pressurizing unit be sure to set the
guage or regulator from 10-20psi (.7-1.4bar).
• Al presurizar la unidad sea seguro fijar la medida o el
regulador de 10-20psi (7-1.4bar).
• En pressurisant l'unité soyez sûr de placer la jauge ou le
régulateur de 10-20psi (7-1.4bar).
• Wenn Sie Maßeinheit unter Druck setzen, seien Sie sicher,
das Eichmaß oder den Regler von 10-20psi (7-1.4bar)
einzustellen.
• Ao pressurizar a unidade seja certo ajustar o guage ou o
regulador de 10-20psi (7-1.4bar).
• Nel pressurizzare l'unità sia sicuro regolare il misuratore o
il regolatore da 10-20psi (7-1.4bar).
PSI
0
50
100
150
200
250
300
Nitrogen
Tank
Hose
Regulator
Air Chuck
580
Fitting
CAPTIVE SCREW
To secure in place, tighten captive screw.
• Para asegurar en lugar, apriete el tornillo prisionero.
• Pour fixer en place, serrez la vis captive.
• Um im Platz zu sichern, ziehen Sie Sicherheitsschraube
fest.
• Para fixar-se no lugar, aperte o parafuso prisioneiro.
• Per fissare sul posto, stringa la vite prigioniera.
15
14
13
16
Place the air chuck on the tank valve and
begin filling until pressure relief valve opens.
• Coloque la tirada del aire en la válvula del tanque y comience
a llenar hasta que la válvula de descarga de presión se abre.
• Placez le mandrin d'air sur la valve de réservoir et commencez
à remplir jusqu'à ce que la valve de décompression s'ouvre.
• Setzen Sie die Luftklemme auf das Behälterventil und fangen Sie
an zu füllen, bis Druckablaßventil sich öffnet.
• Coloque o mandril do ar na válvula do tanque e comece a
encher-se até que a válvula de escape de pressão abra.
• Disponga il mandrino dell'aria sulla valvola del carro armato e
cominci a riempirsi fino a che la valvola limitatrice della
pressione non si apra.
Air Chuck
Tank
Valve
Open the relief valve. Drain all air from the housing and
repeat twice to remove all moisture.
• Abra la válvula de descarga. Drene todo el aire de la cubierta y
de la repetición dos veces para quitar toda la humedad.
• Ouvrez la soupape de sécurité. Évacuez tout l'air le logement et la
répétition deux fois pour enlever toute l'humidité.
• Öffnen Sie das Sicherheitsventil. Lassen Sie alle Luft aus dem
Gehäuse und der Wiederholung zweimal ab, um alle Feuchtigkeit
zu entfernen.
• Abra a válvula de escape. Drene todo o ar da carcaça e do
repeat duas vezes para remover toda a umidade.
• Apra la valvola di sfiato. Vuoti due volte tutta l'aria
dall'alloggiamento e dalla ripetizione per rimuovere tutta l'umidità.
The beam angle may be adjusted on the
bottom of the unit.
• Energía encima de la unidad.
• Puissance vers le haut de l'unité.
• Energie herauf die Maßeinheit.
• Poder acima da unidade.
• Alimentazione sull'unità.
12
Power up the unit.
After purging check the housing pressure. It
should be around 5psi (.34bar).
• Después de purgar el cheque la presión de la cubierta.
Debe estar alrededor de 5psi (34bar).
• Après la purge du contrôle la pression de logement. Elle
devrait être autour de 5psi (34bar).
• Nachdem Überprüfung der Gehäusedruck bereinigt
worden ist. Sie sollte um 5psi (34bar) sein.
• Após ter removido a verificação a pressão da carcaça.
Deve ser em torno de 5psi (34bar).
• Dopo l'eliminazione dell'inceppo del controllo la pressione
dell'alloggiamento. Dovrebbe essere intorno a 5psi
(34bar).
PSI
0
5
10
15
20
25
30
17
19
18
20
PRESSURIZED HOUSING
Replacement Parts List
4
3
2
1
1
5
7
6
12
11
8
10
9
16
14
15
17
13
Part No. Description
1 RPPFDT02 Housing Top (Extended)
2 RPVL1938 Removable Pendent Coupling
3 RPVL1802 Plastic Rain Shroud
4 RPVL1795 Tank Valve Gasket
5 RP96RSORG11 Main O-Ring 9.25"
6 RPPFDTR01 Trim Ring w/o Dome
7 RCPFD7 Clear Dome with sealing O-Ring
7b RCTPFD7 Tinted Dome with sealing O-Ring
8 RPPFDT03 Internal Sealing Bracket Assembly
9 RP96RSORG10 Small O-Ring 4.5"
10 RP70PT07a Hermetic Connector, Gasket, Cable
11 RP95VALV08 5 to 7 psi Pressure Relief Valve
12 RP95VALV07 Tank Valve
13 RPFD072 24VAC Heater
14 RP46PKH3063 Spacers Packet
15 RPFD050 Connection PCB
16 RPFD060 Main Bracket Assembly
17 RPFD080 Blower
N/S RP40CAPPFD811 External Input Video/Power Cables
N/S RP46PKH2200 Packet Assembly-Hardware
N/S RP46PKE1100 Packet Assembly-Electrical
19
20
18
21
23
22
18 RPVL2857 P/T Base Bracket
19 RP76v385A P/T Connection Card
(Network Models Only)
20 RPVL3097 IP Card Bracket
21 RP70p14015 IP Card
22 RP96PSGK08 P/T Grommet (2)
23 RP76P0F060E IP Connection Card
(Network Models Only)
(Network Models Only)
N/S WM20G GOOSE NECK (SOLD SEPARATELY
)
Product Registration/Warranty
Thank you for choosing Videolarm. We value your patronage and are solely committed to
providing you with only the highest quality products available with unmatched customer service
levels that are second-to-none in the security industry.
Should a problem arise, rest assure that Videolarm stands behind its products
by offering some of the most impressive warranty plans available: 3 Years
on all Housings, Poles, Power Supplies, and Accessories and 5 Years on
all camera systems (SView, QView, Warriors), and InfraRed Illuminators.
Register Your Products
Option 1: Online Option 2: Mail-In
Take a few moments and validate your purchase with our Online Product Registration Form
at
www.videolarm.com/productregistration.jsp
or complete and mail-in the bottom portion of this flyer.
Register your recent Videolarm purchases and benefit from the following:
Simple and Trouble-Free RMA process•
Added into customer database to receive product updates / news•
Eliminate the need to archive original purchase documents: •
Receipts, Purchase Orders, etc…
Main Contact Info
First Name: Last Name:
Professional Title: Company:
Address 1: Address 2:
City: State / Province/Country:
Zip / Postal Code: Phone Number: E-mail Address:
Product Information
Please Circle One: Business Personal
Name & Location of Company / Store where Purchased:
(City, State, Country)
Videolarm Product ID Product Description
Serial #
(Available only for Camera Systems, IR Illuminators, Wireless Devices)
PO#
Cut at the dotted Line
Place in envelope, affix stamp and mail to:
Videolarm ATTN: Warranty
2525 Park Central Ave.
Decatur, GA 30035
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Moog Videolarm PFD7TS-3 Manuale utente
- Categoria
- Accessori per telecamere di sicurezza
- Tipo
- Manuale utente
in altre lingue
- English: Moog Videolarm PFD7TS-3 User manual
Documenti correlati
-
Moog Videolarm SView PFD7CS-3 Installation And Operation Instructions Manual
-
-
Moog Videolarm FDW75 Installation And Operation Instructions Manual
-
-
-
-
-
-
-
Moog Videolarm FDP7C12S-3 Manuale utente