EnGenius A8J-EUB1200AC-1 Manuale utente

EnGenius

®

EUB1200AC Dual Band Wireless AC1200 USB Adapter

User Manual

V1.0.0

TABLE OF CONTENTS

I

TABLE OF CONTENTS

Introduction

Introduction 1-1

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

USB Adapter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Ad-hoc (peer-to-peer) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Infrastructure Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

WPS Setup 1-3

TABLE OF CONTENTS

II

Windows

USB Adapter 2-1

Before you Begin 2-1

Installing and Uninstalling the Driver 2-1

Installing the Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Uninstalling the Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Wireless LAN Utility 2-4

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Wireless Network Properties Dialog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Adding a Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

Editing a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Available Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

Wi-Fi Protected Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12

TABLE OF CONTENTS

III

MAC OS X

USB Adapter 3-1

Installing and Uninstalling the Driver 3-1

Installing the Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Uninstalling the Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Wireless LAN Utility 3-4

Link Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Wireless Network Properties Dialog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

Adding a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6

Editing a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8

Available Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

Wi-Fi Protected Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Appendix A

Federal Communication Commission Interference Statement A-1

Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2

TABLE OF CONTENTS

IV

Appendix B

Industry Canada Statement B-1

Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Appendix C

Europe – EU Declaration of Conformity C-1

Appendix D

WorldWide Technical Support D-1

Introduction

Chapter 1

INTRODUCTION INTRODUCTION

1-1

1.1 Introduction

The EnGenius EUB1200AC delivers the next generation of

802.11ac wireless technology and makes your wireless connec-

tivity faster and wider to meet the growing demand for stream-

ing high-bandwidth video and other multimedia applications.

It supports the 2T2R MIMO architecture with fully forward com-

patibility with IEEE802.11n. With up to 300 or 867 Mbps speed

and dual band technology, the EUB1200AC can avoid Wi-Fi

signal interference and ensure top Wi-Fi speeds and reliable

connections. The incredible speed of the EUB1200AC USB

adapter makes heavy traffic networking activities more flexible

and takes the wireless into practical road.

Features

 Up to 300 or 867 Mbps Wireless Speed

 Backward compatible with IEEE 802.11a/b/g/n

 Dual-Frequency Band (2.4GHz/5GHz)

 High Speed USB 3.0 Interface

 WPS Button for Wireless Easy Setup

 Support WEP/WPA and WPA2 Security Encryption

Package contents

Open the package carefully, and make sure that none of the

items listed below are missing. Do not discard the packing

materials, in case of return; the unit must be shipped in its origi-

nal package.

 1x EUB1200AC

 1x Quick Start Guide

 1x CD Manual/Utility

USB Adapter Description

The LED shows the Power and Link (traffic) status. The WPS

button is located on the opposite side of the LED.

WPS

LED

INTRODUCTION SYSTEM REQUIREMENTS

1-2

System Requirements

The following are the minimum system requirements in order to

use the USB adapter.

 PC/AT compatible computer with a USB interface.

 Windows 2000/XP/Vista or MAC OS operating system.

 30 MB of free disk space for installing the USB adapter

driver and utility program.

Applications

EnGenius wireless LAN products are easy to install and easy to

use. The following list describes some of the many applications

made possible through the EnGenius wireless LAN products:

 Difficult-to-wire environments

 Temporary workgroups

 Accessing real-time information

 Frequently changing environments

 Small Office and Home Office (SOHO) networks

 Wireless extensions to Ethernet networks

 Wired LAN backup

 Training and Educational facilities

Network Configuration

To better understand how the wireless LAN products work

together to create a wireless network, it might be helpful to

depict some of the possible wireless LAN PC card network con-

figurations.

EnGenius wireless LAN products can be configured as:

 Ad-hoc (or peer-to-peer) for departmental or SOHO LANs.

 Infrastructure for enterprise LANs.

Ad-hoc (peer-to-peer) Mode

This is the simplest network configuration with several comput-

ers equipped with the PC Cards that form a wireless network

whenever they are within range of one another. In ad-hoc

mode, each client is peer-to-peer, would only have access to

the resources of the other client and does not require an access

point. This is the easiest and least expensive way for the SOHO

to set up a wireless network. The image below depicts a net-

work in ad-hoc mode.

Infrastructure Mode

The infrastructure mode requires the use of an Access Point

(AP). In this mode, all wireless communication between two

computers has to be via the AP. It doesn’t matter if the AP is

stand-alone or wired to an Ethernet network. If used in stand-

alone, the AP can extend the range of independent wireless

LANs by acting as a repeater, which effectively doubles the dis-

tance between wireless stations.

INTRODUCTION WPS SETUP

1-3

1.2 WPS Setup

1. Press and hold down the WPS button on your router

(check with the User Manual that came with your router

for any further instructions if necessary).

2. Within 2 minutes, press and hold down the WPS button

on the EUB1200AC for 2 seconds. The LED should start

to blink.

3. Wait for 2 minutes.

4. Confirm that the connection was successful by opening a

web browser or checking the wireless signal indicator

icon.

Windows

Chapter 2

WINDOWS USB ADAPTER

2-1

2.1 USB Adapter

2.1.1 Before you Begin

During the installation, XP may need to copy systems files from its installation CD. Therefore, you may need a copy of the Windows

installation CD at hand before installing the drivers. On many systems, instead of a CD, the necessary installation files are archived

on the hard disk in C:\WINDOWS\OPTIONS\CABS directory.

2.1.1 Installing and Uninstalling the Driver

Installing the Driver

Before you can use the EUB1200AC Dual Band USB Adapter

you must install the device driver.

To install the USB adapter drivers, follow these steps:

1. Insert the CD-ROM that was provided to you in this pack-

age. The setup should run automatically. If the setup does

not run automatically, then the setup.exe file must be

selected manually from the CD-ROM drive.

WINDOWS INSTALLING THE DRIVER

2-2

2. Click on Windows Driver to start the install process. 3. Click on the Next button to begin the driver installation.

WINDOWS UNINSTALLING THE DRIVER

2-3

4. Wait until the driver and client utility is installed. 5. When installation is complete click on the Finish button to

restart your computer.

Uninstalling the Driver

If you want to remove the EUB1200AC EUB1200AC Dual Band

USB Adapter from your system, use device’s uninstall applica-

tion or the Windows uninstall process.

WINDOWS WIRELESS LAN UTILITY

2-4

2.2 Wireless LAN Utility

There are five sections that allow the user to configure and

monitor the device: general, profile, available networks, status,

and Wi-Fi protected setup.

Additional configuration options located at the bottom of the

window that define the behavior of the utility. The available

options are as follows:

Show Tray Icon: Show/hide the Utility icon in the system tray.

Radio Off: Temporarily turn off wireless radio.

Disable Adapter: Temporarily disable the wireless adapter

General

The General section shows the connection status, speed, type,

encryption, SSID, signal strength, and link quality of the

AC1200 Dual Band USB Adapter.

Click on the Renew IP button to re-initiate the wireless connec-

tion with the AP.

WINDOWS PROFILE

2-5

Profile

The Profile section is used to create and modify profiles that the

AC1200 Dual Band USB Adapter uses to connect to access

points.

To create or modify an access point profile, use the following

buttons:

Add: Manually enter an access point’s configuration settings.

Edit: Modify an access point’s configuration settings.

Remove: Delete the configuration settings of an access point.

Duplicate: Clone an access point’s profile.

Set Default: Reset all saved settings.

Wireless Network Properties Dialog

Use the wireless network properties dialog to enter the connec-

tion properties for an access point.

Fill in the following wireless network properties to create an

access point profile:

Ad hoc Enables the adapter to operate in ad hoc or infrastruc-

ture mode.

Profile Name The name of the access point that is shown in

the profile list.

Network Name (SSID) The name of the access point as

shown on the network.

Channel The channel that the access point is broadcasting on.

WINDOWS ADDING A PROFILE

2-6

Network Authentication The protocol used for network

authentication.

Data Encryption The protocol used for data encryption.

ASCII Enables use of ASCII characters in the passphrase.

Passphrase Enables the use of hexadecimal characters pass-

phrase.

Key Index (advanced) User has to specify which of the four

keys will be active. Please make sure that both the AP/Router

you are connected to and the EUB1200AC use the same key.

Network Key The encryption key used to encrypt the data

packets during data transmission.

Adding a Profile

Note:

When using the ASCII or PASSPHRASE feature the

password must be obtained from the router.

To add a profile, follow these steps:

1. Click the Add button.

2. Select the checkbox to specify an ad hoc network.

Note:

If the ad hoc checkbox is selected, Profile Name is not

available.

WINDOWS ADDING A PROFILE

2-7

3. Enter the profile name in Profile Name.

4. Enter the SSID in the Network Name (SSID).

Note:

The list of channels is only available if the ad hoc check-

box is selected.

5. Select a channel from the Channel list. Available chan-

nels are from 1 to 161.

6. Select a network authentication protocol from the Net-

work Authentication protocol list. The following proto-

cols can be selected:

 Open System

 Shared Key

 WPA-PSK

 WPA2-PSK

 WPA 802.1X

 WPA2 802.1X

 WEP 802.1X

7. Select the ASCII checkbox to enter a password using

ASCII characters.

WINDOWS ADDING A PROFILE

2-8

8. Select the PASSPHRASE checkbox to enter a password

using hexadecimal characters. The passphrase key

length can be either 64 or 128 bits.

9. Select the key index from the Key index list.

10.Enter the network key value in Network key.

11.Enter the same network key value again in Confirm net-

work key.

12.Click the OK button to save the profile settings or the

Cancel button to discard settings.

Editing a Profile

Note:

When using the ASCII or PASSPHRASE feature the

password must be obtained from the router.

To edit a profile, follow these steps:

1. Click the Edit button.

2. Select the checkbox to specify an ad hoc network.

Note:

If the ad hoc checkbox is selected, Profile Name is not

available.

3. Enter the profile name in Profile Name.

WINDOWS ADDING A PROFILE

2-9

4. Enter the SSID in the Network Name (SSID).

Note:

The list of channels is only available if the ad hoc check-

box is selected.

5. Select a channel from the Channel list. Available chan-

nels are from 1 to 161.

6. Select a network authentication protocol from the Net-

work Authentication protocol list. The following proto-

cols can be selected:

 Open System

 Shared Key

 WPA-PSK

 WPA2-PSK

 WPA 802.1X

 WPA2 802.1X

 WEP 802.1X

7. Select the ASCII checkbox to enter a password using

ASCII characters.

WINDOWS AVAILABLE NETWORK

2-10

8. Select the PASSPHRASE checkbox to enter a password

using hexadecimal characters. The passphrase key

length can be either 64 or 128 bits.

9. Select the key index from the Key index list.

10.Enter the network key value in Network key.

11.Enter the same network key value again in Confirm net-

work key.

12.Click the OK button to save the profile settings or the

Cancel button to discard settings.

Available Network

You can find access points that are within the proximity of your

adapter by using the device to scan for them.

The information returned by the adapter is shown in a list and

includes the SSID, channel, encryption type, authentication

type and signal strength.

If you want to view available access points, click the Refresh

button.

If you want to add an access point to your list of profiles, click

on the Add to Profile button.

La pagina sta caricando ...

EnGenius A8J-EUB1200AC-1 Manuale utente

Questo manuale è adatto anche per

EnGenius A8J-EUB1200AC-1 Manuale utente

in altre lingue

Documenti correlati

Altri documenti