Yamaha DPX-1300 Manuale del proprietario

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan WF80500

DPX-1300

G

BEDIENUNGSANLEITUNG

DIGITAL CINEMA PROJECTOR

PROJECTEUR CINEMA NUMERIQUE

DPX-1300

10_DPX-1300-Cover1-4_G.p65 9/22/05, 4:34 PM1

Caution: Read this before operating this unit.

•To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

Installation

• Install this unit in a well-ventilated, cool, dry, clean place with

at least 30 cm (1 feet) clearance on the top, right and left, and

at the back of this unit — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

• Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or

electrical shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

• Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

• On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

• Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to restrict heat dissipation. If the temperature

inside this unit rises too much, it may cause fire, damage to this

unit, and/or personal injury.

•When installing this unit on the ceiling, make sure the ceiling

has sufficient strength to support this unit and the ceiling

mounts for an extended period of time. Installation must be

performed only by qualified service personnel.

• Install this unit near the AC outlet and where the AC power

plug can be reached easily.

Operation

• Remove the lens cover before starting any operation of this unit

to prevent the heat from staying around the lens. Operation

with the cap on may cause damage to this unit.

• Do not plug in this unit to a wall outlet until all connections are

complete.

• Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than that

specified.

• Do not use force on switches, knobs and/or cords.

•Take care of this unit so that no foreign objects and/or liquid

drop inside this unit.

•To prevent damage by lightning, keep the power cord out and

outdoor antennas disconnected from a wall outlet or te unit

during the lightning storm.

• Do not look into the lens while this unit is turned on. It may

cause serious damage to your eyesight.

• Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

• Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

• When not planning to use this unit for a long period of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

•When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cable.

• Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

Others

• Clean the lens carefully so as not to create any scratches by

using a blower or lens paper.

•Replace the lamp when the LAMP warning indicator blinks in

red after the lamp usage has exceeded 2000 hours. Follow the

lamp replacement procedure described in this manual.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below.

Note

•The plug severed from the mains lead must be destroyed, as a plug with

bared flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked by the letter

E or by the safety earth symbol or coloured GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

i

10_DPX_1300_cau_G 9/20/05, 5:07 PM1

1

Table of contents

1 Getting started 2

Inappropriate places for installation ....... 2

Accessory check .................................... 2

2 Features 3

3 Controls and functions 4

4 Remote control 6

5 Preparation 10

6 Installation 12

Setting up the DPX-1300 ..................... 12

Projection distance ............................... 13

Projection image position ..................... 14

7 Connection 15

Connecting to AV components ............. 15

Connecting to computer devices ......... 16

8 Projection 17

Checking installation and connections...

17

Turning the projector power on ............ 18

Selecting an input signal ...................... 20

Adjusting the image ............................. 25

9 Menu 27

Menu configurations ............................ 27

Menu items .......................................... 28

Menu operations .................................. 38

10

Memory function

(Saving, Recall, Lock, Copy, Reset) 48

11

Reference 55

Glossary ............................................... 55

Compatible signal types ....................... 56

Maintenance ......................................... 58

Troubleshooting.................................... 60

Message display .................................. 62

LED Indicator meanings ....................... 63

Specifications ....................................... 64

Dimensional drawing ............................ 65

Getting started

Features

Controls and functions

Remote control

Preparation

Projection

Menu

Memory function

Reference

11

10

9

8

7

6

5

4

3

2

1

Connection

Installation

English

11_DPX-1300_E.p65 9/20/05, 5:07 PM1

2

◆Inappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place

to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely

low.

• This unit must be used within a temperature range of 5 to 35°C.

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

•Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

•The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Warning

•To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

◆Accessory check

Please check that all accessories listed here are included in your package.

• Remote control • Batteries (AA, UM-3 or R6) • Power cable

• Pin/BNC adapters • Lens cap

1 Getting started

45

RESET

6

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

B

D4

DVI

S VIDEO

A

INPUT

MEMORY

HDMI

INPUT

MENU

ASPECT

ESCAPE

11_DPX-1300_E.p65 9/20/05, 5:07 PM2

3

Features

2

English

Adjust 7 colors independently (including white), or use the

automatic color balance function

The DPX-1300 allows you to adjust the 7-axis WRGBYCM color coordinate and gain

parameters directly. For better consistency, you can also control color temperature and RGB

balance together, allowing you to check that the changes you make are always consistent with

your preferences.

The digital interface provides sharp, detailed images

The DPX-1300 is equipped with an HDMI terminal, which is set to become the standard for the

coming generation of products. Connect to a DVD player or set-top box with a HDMI terminal

to receive digital image data directly, and enjoy completely digitally processed images.

Compatible with the content protection function of HDCP.

Intelligent memory functions

The DPX-1300 can store six image memory settings, called memory numbers, for each input

jack. For each memory number, you can set parameters for different input resolutions, and the

unit will switch to the appropriate parameters when it begins displaying an image of an

appropriate resolution. For example, the unit automatically changes display settings without

changing memory numbers when you change from watching a DVD to watching a HDTV

image for which you have set different image menu item parameters.

In-line menus for image adjustment

You can access image adjustment menu items at the touch of a button, and adjust images while

viewing them without opening the menu screen.

Highly configurable electronic adjustment gives you the

freedom to place the projector wherever you want

A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the

projector in a wide range of environments. You can also use the remote control to access many

lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing

position.

Uses the DMD

TM

device 720p DarkChip3

TM

The projector uses the high contrast “720p DarkChip3

TM

”, to reduce black levels even further

and reproduce contrasts close to that of a film.

2 Features

11_DPX-1300_E.p65 9/20/05, 5:07 PM3

4

◆Main unit <Front panel and controls>

STANDBY

/

ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

MENU

INPUT

DIGITAL CINEMA PROJECTOR DPX-1300

ASPECT

1

2

3

4

5

1

6

7

8

9

0

STANDBY

/

ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

MENU

INPUT

ASPECT

A

E

B

CD

2 STANDBY/ON button

Switches the unit between Standby and On (operational)

modes.

3 ESCAPE button

Exits from submenus.

4 PATTERN button

Switches the built-in test pattern on and off.

5 ASPECT button

Turns the display aspect menu for the project image on and off.

6 (Enter) button

Sets values when the DPX-1300 is displaying the menu. When

the menu is not displayed, the DPX-1300 displays the in-line

image quality adjustment menu. (☞ page 47)

1 LED Indicators

The main unit is equipped with 5 indicators to display various states of operation. See page 63 for explanations of the LED indicator

meanings.

7 MENU button

Switches the settings and adjustments menu display on and off.

8 SETTING button

Selects lens adjustment modes.

9 INPUT button

Switches the input signal selection menu display on and off.

0 Cursor buttons

Use the h, g, +, - buttons for system operations, menu item

selection, and changing system values.

A STANDBY/ON indicator

(There is also an LED on the front panel of the main unit.)

B LAMP warning indicator

C COVER warning indicator

D TEMP warning indicator

E FAN warning indicator

Lamp cover

Ventilation inlet

Adjustable feet

Makes small adjustments to

the projection angle

Lens

Exhaust vent

Front remote control sensor

STANDBY/ON indicator

3 Controls and functions

Lens cap

11_DPX-1300_E.p65 9/20/05, 5:07 PM4

5

Controls and functions

3

English

HDMIDVI

G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC

VD

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

BPR/YCBCR

RS-232C

D4 VIDEO

wq

8

765432190

ert

◆Main unit <Rear panel / Connections>

1 INPUT B (D-sub 15 pin)

Receives component video and RGB (RGB/YPBPR/YCBCR)

signals. Use a D-sub monitor cable to connect components to

this jack.

2 D4 VIDEO (D jack)

Receives signals output from the D jacks of other AV

components. It is compatible with D1 - D4 formats.

3 - 7 INPUT A (BNC jacks)

Receive component video and RGB signals. Connect

component signal connectors from AV components to input

jacks 3 - 5, and RGB signal connectors from computers to

input jacks 3 - 7. Use BNC cables for these connections.

3 G/Y (G, or luminance signal)

4 B/P

B/CB (B, or color difference signal)

5 R/P

R/CR (R, or color difference signal)

6 HD/SYNC (Horizontal sync signal, composite sync signal)

7 VD (Vertical sync signal)

8 S VIDEO (Mini DIN jack)

Receives signals from S-VIDEO output jacks of other AV

components. Use an S-VIDEO cable for these connections.

9 AC inlet

Insert the supplied AC power cable here.

0 VIDEO (Pin Jack)

Receives composite video signals from the VIDEO output

jacks of other AV components. Use a video pin cable for these

connections.

q DVI (DVI jack)

Receives RGB signals from computers or AV components. Use

a DVI cable for this connection.

w HDMI

TM

(HDMI

TM

jack)

Receives HDMI

TM

signals from computers or AV components.

e REMOTE IN / OUT jack

Connect the remote control to the REMOTE IN jack if you

want to use it through a cable. The REMOTE OUT jack

outputs the signal received through the REMOTE IN jack

without any change.

r RS-232C (D-sub 9 pin)

For use in servicing this unit.

t TRIGGER OUT

Outputs control signals to external components. This output

provides a potential of 12 V/ maximum 200 mA when this unit

is projecting. Use the supplied trigger-out DC plug (for US

model only) to control external components.

Rear remote control sensor

11_DPX-1300_E.p65 9/20/05, 5:07 PM5

6

◆ Remote control functions

Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control,

point it at the remote control sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.

1 Transmit indicator

Lights up when the remote control sends infrared signals to the

main unit.

2 AUTO button

Automatically sets the DPX-1300 to the best settings for the

type of signal it is currently receiving.

3 V.POS button

Switches on or off the vertical adjustment mode for the entire

image.

4 ZOOM button

Switches on or off the size adjustment mode for the image the

DPX-1300 is projecting.

5 IRIS button

Switches on or off the lens iris change mode.

6 ESCAPE button

Exits from submenus.

7 Cursor buttons

Use the h ,g, +, - buttons to move the cursor within the on-

screen display.

8 ASPECT button

Turns the display aspect menu for the project image on and off.

9 RESET button

Resets all adjustable parameters to their default settings.

0 STILL button

Stops a moving image, displaying a still of the image the DPX-

1300 is projecting. Press STILL again to cancel this effect.

q INPUT area

Selects the INPUT jacks directly.

w MEMORY area

Calls stored memory (all parameter settings) directly.

e button

Switches the unit between Standby and On (operational)

modes.

r FOCUS button

Switches on or off the focus adjustment mode for the image the

DPX-1300 is projecting.

t PATT (PATTERN) button

Switches on and off the built-in test pattern.

y MENU button

Switches on and off the settings and adjustments menu display.

u (Enter) button

Sets values when the DPX-1300 is displaying the menu. When

the menu is not displayed, the DPX-1300 displays the in-line

image quality adjustment menu. (☞ page 47)

4 Remote control

45

RESET

6

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

B

D4

DVI

S VIDEO

A

INPUT

MEMORY

HDMI

INPUT

MENU

ASPECT

ESCAPE

o

i

u

y

t

p

r

e

1

2

3

4

5

6

7

8

9

0

q

w

11_DPX-1300_E.p65 9/20/05, 5:07 PM6

7

Remote control

4

English

i INPUT button

Switches on and off the input signal selection menu display.

o LIGHT switch

Moving this switch lights the high-use AUTO (2), ESCAPE

(6), ASPECT(8) , (e), MENU (y), and INPUT (i)

buttons. The light disappears if you do not perform any

operation within 10 seconds.

p HIDE button

Temporarily halts projection of the image the DPX-1300 is

currently displaying. Press again to cancel this effect.

a Remote control code switch

Selects ID-1 or ID-2 when operating two main units with one

remote control. You can set the ID for the main unit in the

menu (The default setting is ID-1).

s Remote control cable jack

Connect this jack and REMOTE IN jack on the main unit using

a cable (commercially available) to use the remote control with

a wired connection. (☞ page 8)

INPUT

I

RIS

V

.POS

AU

T

O

PATT

FO

C

US

ZO

O

M

S

E

T

I

N

G

I

D-2

ID

-

1

RESET

H

ID

E

ST

I

L

S VIDEO

VIDEO

B

D4

A

DVI

4

5

6

1

2

3

HDMI

MEMORY

LIGHT

INPUT

MENU

E

SCAPE

ASPECT

a

s

11_DPX-1300_E.p65 9/20/05, 5:07 PM7

8

◆Loading the batteries into the remote control

1. Remove the battery compartment cover.

2. Insert two batteries (AA, UM3, or R6 type), matching the polarity

markings on the batteries with those in the battery

compartment.

3. After loading the batteries, close the cover until it snaps into

place.

Warning

• If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the

batteries for new ones.

• Do not mix old and new, or different types of batteries.

• Remove the batteries if you do not plan to use the unit for a long time.

• If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact

with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly

before installing new batteries.

◆Using the remote control with a wired connection

Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the

REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1300 without having to be within range

of the remote sensor.

1

3

2

I

R

I

S

V.P O

S

A

U

T

O

PATT

FOCUS

ZOO

M

SE

T

I

N

G

ID-2

I

D

-

1

R

ESET

H

IDE

STIL

L

4

5

6

1

2

3

LIGH

T

I

N

PUT

M

E

N

U

ESCAPE

AS

PE

CT

INPUT

INPU

T

S

V

IDE

O

VID

E

O

B

D4

A

D

V

I

HD

MI

HDMIDVI

G/Y B/P

B/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YPBPR/YCBCR

RS-232C

D4 VIDEO

11_DPX-1300_E.p65 9/20/05, 5:07 PM8

9

Remote control

4

English

Distance to sensor Angle to sensor

7 m 30˚ vertically and horizontally

(approximate value) (approximate value)

◆ Limits for using the remote control

Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits

described here.

Warning

• Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.

• Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit

functioning.

Use within a left/right arc of 30 degrees Use within a vertical arc of 30 degrees

HDMI

G/Y B/P

B

/C

B

R/P

R

/C

R

INPUT A

HD/SYNC

VD

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

B

P

R

/YC

B

C

R

RS-232C

D4 VIDEO

45

RESET

6

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

BDVI

S VIDEO

A

D4

INPUT

MEMORY

HDMI

INPUT

MENU

ASPECT

ESCAPE

45

RESET

6

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

BDVI

S VIDEO

A

D4

INPUT

MEMORY

HDMI

INPUT

MENU

ASPECT

ESCAPE

11_DPX-1300_E.p65 9/20/05, 5:07 PM9

10

Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.

You can begin projection as soon as installation is complete.

Refer to the sections below for information on how to install the main unit to suit your viewing environment.

◆If you have not installed the main unit or screen

• Immediately after purchase, when you have not installed either the main unit or a screen.

• When moving the main unit and screen to a new location.

◆If you have installed the main unit and screen, and connected a

source component

• You have installed the main unit and screen, and connected source components.

• You are using the main unit in a previously installed location with previously connected source components.

◆If you have installed the main unit and screen, but not connected

any image playback components

• You have installed the main unit and screen, but not connected any source components.

• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.

You do not need to carry out step 3 or step 4 if you

do not want to adjust the projection image. If the

unit does not project the image correctly, it may not

be connected correctly. In this case, carry out this

procedure starting from step 2.

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

Projection

preparations

complete

STEP2

Connect AV

components or a

computer to the

main unit.

☞ page 15 - 16

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

Projection

preparations

complete

STEP 1

Install the main unit

and screen.

☞ page 12

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP2

Connect AV

components or a

computer to the

main unit.

☞ page 15 - 16

Projection

preparations

complete

5

Preparation

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

11_DPX-1300_E.p65 9/20/05, 5:07 PM10

11

Prepararion

5

English

Step2

Connect an AV component or computer

• Connect AV components

• Connect a computer ☞ page 15 - 16

Step3

Turn the power on and selecting an

image for projection

•Turn on the projector power

•Begin playback of the input image

• Select an input signal

• Select a projection image aspect

• Adjust the image

Focus/Vertical and Horizontal position/Size/Iris

☞ page 17 - 26

Step1

Set up the projector and screen

• Install the projector

• Install the screen ☞ page 12 - 14

Only adjust these

parameters when

necessary. It is not

necessary to adjust these

settings once you have set

them initially.

Step4

Use the menu to adjust the image quality and

other parameters

• Image quality: Set image quality details

• Signal setting: Set input signal details

• Default settings: Set the default settings for everyday use

• Installation settings: Set to suit your viewing environment ☞ page 27 - 47

11_DPX-1300_E.p65 9/20/05, 5:07 PM11

12

Setting up the DPX-1300

◆ Mounting the projector on a table

A: From in front of a screen

Place the unit on a table to project and view the image from in front of the screen. Usually,

place the unit on a reasonably high table. The height from the bottom of the unit to the center

of the lens is 12.4 cm (4”-7/8).

B: From behind a screen (using a semi-translucent screen)

Place the unit on a table to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “A: From in

front of the screen”.

• Set the [Location] menu item in the [Setup] menu group to [Rear/Table]. (☞ page 27 - 47)

◆ Mounting the projector on the ceiling

There are two kinds of brackets (sold separately: PMT-L31 and PMT-H35), which you can use to mount the projector on the ceiling. Please

consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor.

C: From in front of a screen

Mount the unit on the ceiling to project and view the image from in front of the screen. The

distance between the projector and the screen should be the same as “A: From in front of the

screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Front/Ceiling]. (☞ page

27 - 47

)

D: From behind a semi-translucent screen

Mount the unit on the ceiling to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “B: From

behind a screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Rear/Ceiling]. (☞ page

27 - 47

)

There are four ways of mounting the projector.

6

Installation

Mounting method

Placed on a table

Mounted on the

ceiling

Projection method

A: From in front of a screen

C: From in front of a screen

B: From behind a semi-translucent screen

D: From behind a semi-translucent screen

11_DPX-1300_E.p65 9/20/05, 5:07 PM12

13

Installation

6

English

The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal

length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter

the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine

the best location to place the projector in to suit your screen size.

Projection distance

Since the DPX-1300 has a 16:9 panel, the ideal installation location for use with a 4:3 screen depends on the size of the image you wish to

view.

60'' 80'' 100'' 150'' 200''

*These are theoretical values.

During actual use there may be a deviance of a few percent.

(*1) Projects a 16:9 image that completely fills the screen (leaves a black line at the top and bottom of the screen).

(*2) Projects a 4:3 image that completely fills the screen.

(*3) When projecting both 16:9 and 4:3 images.

You can use the zoom function to make efficient use of the screen for both *1 and *2 above. The projection distance in this case is

between Wide in *2 and Tele in *1. Use the zoom to adjust the size of the projection images so that they fill the screen completely. Note

that adjustments to V.POS may cause the position of the image to change.

Projection distance [a]

Lens

centerline

Screen size

60

70

80

90

100

110

120

150

200

Screen size

(inch)

1.78 – 2.88

2.08 – 3.37

2.39 – 3.86

2.70 – 4.35

3.00 – 4.84

3.31 – 5.33

3.62 – 5.82

4.54 – 7.29

6.07 – 9.74

Projection distance [a]

Wide (m) – Tele (m)

Screen size

(inch)

16:9 image (*1)

Wide (m) – Tele (m)

4:3 image (*2)

Wide (m) – Tele (m)

Projection distance[a]

60

80

100

120

200

1.63 – 2.64

2.19 – 3.54

2.76 – 4.44

3.32 – 5.34

5.58 – 8.94

2.17 – 3.52

2.93 – 4.72

3.68 – 5.92

4.43 – 7.12

7.43 – 11.92

(*3)

11_DPX-1300_E.p65 9/20/05, 5:07 PM13

14

Follow the instructions to adjust the position of the projected image on screen.

This illustration shows the limits within which the

zoom function can alter projection distance [a] in

relation to screen size. You can adjust the image

within these limits so that it fills the screen

completely. ( ☞ page 26)

You can adjust the vertical position of the

projection image up or down by half of the height

of the screen. For example, shifting V.POS fully up

brings the lower limit of the image above the

centerline of the lens. (☞ page 25)

If you mount this unit on a tabletop, you can use the adjusters on its underside to change the

position of the projection image. Rotate the movable part of the two screw-type adjusters at

the front bottom of the case to adjust the height. The movement range of the adjusters is 3

cm (1-1/4 inch). Adjust with care as loosening them further than 3 cm may cause them to

separate from the unit.

Projection image position

◆ Keystone adjustment

If you mount the unit at an angle to the screen, it projects trapezoidally distorted images. You can use the [V keystone Correction] or [H

keystone Correction] item in the [Setup] menu group to rectify this. (☞ page 36)

Memo

• If the keystone is adjusted aspect ratio may not be correctly maintained. To correctly maintain the aspect ratio, try to use the DPX-

1300 with the lens shift in the center position.

• The video may be disturbed by keystone correction. Wherever possible, we recommend setting up so the screen and projector

form a right angle.

Wide Tele

Lens centerline

(When shifted

fully up)

Lens centerline

(When shifted

fully down)

11_DPX-1300_E.p65 9/20/05, 5:07 PM14

15

Connection

7

English

Connecting to AV components

This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking

care to use cables and adapters that match the input jacks.

Warning

• Be sure to turn off the power of this unit and the source component before attempting connection.

• Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s

manual for the component.

• Insert all plugs firmly to avoid noise or other problems.

Memo

• Be sure to connect Y/PB/PR and Y/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to

the owner’s manual of the source component for more information. You may need to make connections to HD/SYNC and VD for

RGB video signals.

D connector

cable

D-sub

monitor

cable

BNC cable for

component connection

Pin/BNC

adapters

Pin cable

Video pin cable

S-Video cable

D1—4

output

connectors

Pin jacksD-sub

Component/RGB video output connectors

Image output from AV components

BNC jacks S-Video output

jack

Video output

jack

HDMI cable (digital)

HDMI

output

connector

7 Connection

DVI cable (digital)

DVI output

connector

Input

VIDEO

S VIDEO

INPUT A

INPUT B

D4 VIDEO

HDMI

DVI

Signal type

Composite video

S-Video

Component video/RGB video

Component video

Component video/RGB video (digital)

RGB video (digital)

Connector type

Pin jack

Mini DIN connector

BNC connector x 3-5

D-sub 15 pin

D connector

HDMI connector

DVI connector

HDMI

G/Y B/P

B

/C

B

R/P

R

/C

R

INPUT A

HD/SYNC

VD

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

B

P

R

/YC

B

C

R

RS-232C

D4 VIDEO

DVI

G

/

YR

/

P

R

/

C

R

B

/

P

B

/

C

B

11_DPX-1300_E.p65 9/20/05, 5:07 PM15

16

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and

jacks you wish to use. The HDMI terminal does not support PC signals.

Connecting to computer devices

HDMIDVI

G/Y B/P

B

/C

B

R/P

R

/C

R

INPUT A

HD/SYNC

VD

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

B

P

R

/YC

B

C

R

RS-232C

D4 VIDEO

D-Sub monitor

cable

BNC monitor cable

Monitor output terminal

Computer devices

Input

INPUT A

INPUT B

DVI

Signal type

RGB (Analog)

RGB (Digital)

Connector type

BNC jack x 5

D-sub 15 pin

DVI connector

DVI cable

11_DPX-1300_E.p65 9/20/05, 5:07 PM16

17

Projection

8

English

Checking installation and connections

◆ Pre-operation check

Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.

However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time

you used this unit. Check settings and connections only when the unit does not appear to project images correctly.

PHONO

DVR

STANDBY

/ON

PURE DIRECT

2CH/MULTI CH

SPEAKERS

VIDEO AUX

REC OUT/ZONE 2

INPUT MODE

SOURCE/REMOTE

DVDDTV/LD

MD/TAPE

CD-R

TUNER

CD

VIDEO AUX

VCR 2

VCR 1

SAT

CABLE

A B

STRAIGHT

EFFECT

MULTI CH

INPUT

DSP

PROGRAM

BALANCE

TONE

CONTROL

VOLUME

INPUT SELECTOR

MULTI JOG

SILENT OPTIMIZER

MIC

PHONES

OPTICAL

R

AUDIO

L

VIDEO

S VIDEO

Is the main unit power

turned on?

Main unit

Are the components connected correctly?

“Connecting to AV components”

☞ page 15 - 16

Image source component

Is the source component power

turned on?

For an explanation of detailed settings, see “Menu”. ☞ page 27 - 47

Check installation and connections

Select an image for projection and image adjustment

Projection preparations complete

Turn on the projector power.

Begin playback of the source image for adjustment.

Select a projection image.

(Select an input signal and projection image aspect.)

Adjust focus and vertical/ horizontal positioning.

8 Projection

Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.

To project images, carry out the following procedure.

Is the screen installed correctly?

“Setting up the DPX-1300”

☞ page 12

12_DPX-1300_E.p65 9/20/05, 5:07 PM17

18

◆ Turning the power on

Always remove the lens cap before operating the main unit.

1. Insert the supplied power cable

firmly into the AC inlet at the rear

of the main unit, then insert the

plug into an AC outlet.

The STANDBY/ON indicator lights red.

2. Press the STANDBY/ON button

(the

button on the remote

control).

The indicator blinks green and the lamp

lights up in preparation for projection. After

approximately 35 seconds, the indicator

changes from blinking to steady green,

indicating that the unit is ready to project.

Warning

• Do not remove the power cable while the STANDBY/ON indicator is blinking green or

lit steady green. This could damage the lamp or reduce lamp life.

HDMIDVI

G/Y B/P

B

/C

B

R/P

R

/C

R

INPUT A

HD/SYNC

VD

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

B

P

R

/YC

B

C

R

RS-232C

D4 VIDEO

STANDBY

/

ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

MENU

INPUT

ASPECT

STANDBY/ON

indicator

AC inlet

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY

/

ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

MENU

INPUT

ASPECT

Remote Control Main unit

button STANDBY/ON button

Turning the projector power on

12_DPX-1300_E.p65 9/20/05, 5:07 PM18

La pagina sta caricando ...

Yamaha DPX-1300 Manuale del proprietario

Yamaha DPX-1300 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti