Viglen D945GNT Manuale utente

Intel® Desktop Board

D945GNT/D945GTP

Product Guide

Order Number: D10471-002

Revision History

Revision Revision History Date

-001

First release of the Intel

®

Desktop Board D945GNT/D945GTP Product Guide

March 2005

-002

Second release of the Intel

®

Desktop Board D945GNT/D945GTP Product Guide

April 2006

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to

operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the

Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils

numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des

Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel

®

products. No license, express or implied, by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions

of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating

to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,

or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical,

life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time,

without notice.

Desktop Board D945GNT/D945GTP may contain design defects or errors known as errata which may cause the product to

deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product

order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be

obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling

1-800-548-4725.

Intel, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other

countries.

* Other names and brands may be claimed as the property of others.

iii

Preface

This Product Guide gives information about board layout, component installation, BIOS update,

and regulatory requirements for Intel

®

Desktop Board D945GNT/D945GTP.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for general

audiences.

Intended Uses

All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in

personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar

locations. The suitability of this product for other PC or embedded non-PC applications or other

environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported

without further evaluation by Intel.

Information Layout

The chapters in this Product Guide are arranged as follows:

1 Desktop Board Features: a summary of product features

2 Installing and Replacing Desktop Board Components: instructions on how to install the desktop

board and other hardware components

3 Updating the BIOS: instructions on how to update the BIOS

4 Configuring for RAID (Intel

®

Matrix Storage Technology) Requires Microsoft Windows* XP

or 2000 and SATA Hard Drive(s): information about configuring your system for RAID

A Error Messages and Indicators: information about BIOS error messages and beep codes

B Regulatory Compliance: safety and EMC regulations, product certification

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Intel Desktop Board D945GNT/D945GTP Product Guide

iv

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)

GHz Gigahertz (one billion hertz)

KB Kilobyte (1024 bytes)

MB Megabyte (1,048,576 bytes)

Mbit Megabit (1,048,576 bits)

MHz Megahertz (one million hertz)

Box Contents

• Intel Desktop Board

• I/O shield

• One ATA-66/100 cable

• Two locking Serial ATA cables

• One diskette drive cable

• One VGA port cover

• Quick Reference poster

• Configuration and battery caution statement label

• Intel

®

Express Installer driver CD-ROM

• Intel Express Installer software CD-ROM or DVD-ROM

• Trusted Platform Module Quick Reference (optional)

• Trusted Platform Warning Label (optional)

v

Contents

1 Desktop Board Features.................................................................................9

Manufacturing Options ........................................................................................................11

Supported Operating Systems ............................................................................................11

Desktop Board Components ...............................................................................................12

Processor............................................................................................................................16

Main Memory ......................................................................................................................17

Intel

®

945G Express Chipset...............................................................................................18

Graphics Subsystem ...........................................................................................................18

Audio Subsystem ................................................................................................................18

Input/Output (I/O) Controller ................................................................................................19

LAN Subsystem ..................................................................................................................19

LAN Subsystem Software...........................................................................................19

RJ-45 LAN Connector LEDs.......................................................................................20

Hi-Speed USB 2.0 Support..................................................................................................21

Enhanced IDE Interface ......................................................................................................21

Serial ATA...........................................................................................................................21

Expandability.......................................................................................................................21

BIOS ...................................................................................................................................22

Serial ATA and IDE Auto Configuration ......................................................................22

PCI and PCI Express Auto Configuration ...................................................................22

Security Passwords....................................................................................................22

Chassis Intrusion.................................................................................................................23

Power Management Features .............................................................................................23

ACPI...........................................................................................................................23

Power Connectors......................................................................................................23

Fan Connectors..........................................................................................................23

Fan Speed Control (Intel

®

Precision Cooling Technology)..........................................23

Suspend to RAM (Instantly Available PC Technology) ...............................................24

Wake from USB..........................................................................................................24

Wake from PS/2 Keyboard/Mouse..............................................................................25

PME# Wakeup Support ..............................................................................................25

Speaker...............................................................................................................................25

Battery.................................................................................................................................25

Real-Time Clock..................................................................................................................25

2 Installing and Replacing Desktop Board Components

Before You Begin................................................................................................................27

Installation Precautions .......................................................................................................28

Installation Instructions........................................................................................................28

Ensure Electromagnetic Compatibility (EMC) Compliance..........................................28

Chassis and Component Certifications.......................................................................29

Prevent Power Supply Overload.................................................................................29

Place Battery Marking ................................................................................................29

Installing the I/O Shield .......................................................................................................30

Intel Desktop Board D945GNT/D945GTP Product Guide

vi

Installing and Removing the Desktop Board........................................................................31

Installing and Removing a Processor ..................................................................................32

Installing a Processor .................................................................................................32

Installing the Processor Fan Heat Sink.......................................................................35

Connecting the Processor Fan Heat Sink Cable.........................................................35

Removing the Processor ............................................................................................35

Installing and Removing Memory ........................................................................................36

Installing DIMMs.........................................................................................................38

Removing DIMMs.......................................................................................................39

Installing and Removing a PCI Express* x16 Card..............................................................40

Installing a PCI Express x16 Card ..............................................................................40

Removing the PCI Express x16 Card .........................................................................40

Connecting the IDE Cable...................................................................................................41

Connecting the Serial ATA (SATA) Cable ...........................................................................42

Connecting Internal Headers...............................................................................................43

Installing a Front Panel Audio Solution for Intel

®

High Definition Audio.......................44

Connecting Hi-Speed USB 2.0 Headers.....................................................................45

Connecting IEEE 1394a Headers (Optional)...............................................................45

Connecting the Front Panel Header ...........................................................................46

Setting Up the Flexible 6-Channel Audio with Jack Re-tasking (Optional) ..........................47

Connecting Fan and Power Cables .....................................................................................48

Connecting Fan Cables ..............................................................................................48

Connecting Power Cables ..........................................................................................49

Other Connectors................................................................................................................50

Setting the BIOS Configuration Jumper...............................................................................51

Clearing Passwords ............................................................................................................52

3 Updating the BIOS

Updating the BIOS with the Intel

®

Express BIOS Update Utility...........................................59

Updating the BIOS with the Iflash Memory Update Utility ....................................................60

Obtaining the BIOS Update File..................................................................................60

Updating the BIOS......................................................................................................60

Recovering the BIOS..................................................................................................61

4 Configuring for RAID (Intel

®

Matrix Storage Technology) - Optional

Requires Microsoft Windows* XP or 2000 and SATA Hard Drive(s)

Configuring the BIOS for Intel Matrix Storage Technology..........................................63

Creating Your RAID Set .............................................................................................63

Loading the Intel Matrix Storage Technology RAID Drivers and Software ..................64

Setting Up a “RAID Ready” System............................................................................64

A Error Messages and Indicators

BIOS Beep Codes...............................................................................................................65

BIOS Error Messages .........................................................................................................65

Contents

vii

B Regulatory Compliance

Safety Regulations ..............................................................................................................67

European Union Declaration of Conformity Statement ........................................................67

Product Ecology Statements ...............................................................................................69

Lead-Free Desktop Board ..........................................................................................71

EMC Regulations ................................................................................................................72

Product Certification Markings (Board Level) ......................................................................74

Figures

1. Desktop Board D945GNT Components ........................................................................12

2. Intel Desktop Board D945GTP Components.................................................................14

3. LAN Port LED Locations...............................................................................................20

4. Location of Standby Power Indicator.............................................................................24

5. Installing the I/O Shield.................................................................................................30

6. Desktop Board D945GNT/D945GTP Mounting Screw Hole Locations..........................31

7. Lift Socket Lever...........................................................................................................32

8. Lift the Load Plate and Don’t Touch the Socket Contacts .............................................32

9. Remove the Protective Socket Cover ...........................................................................33

10. Remove the Processor from the Protective Processor Cover/Do Not Touch.................33

11. Install Processor ...........................................................................................................34

12. Close the Load Plate ....................................................................................................34

13. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector ........35

14. Dual Configuration Example 1 ......................................................................................36

15. Dual Configuration Example 2 ......................................................................................36

16. Dual Configuration Example 3 ......................................................................................37

17. Installing a DIMM..........................................................................................................38

18. Inserting a PCI Express x16 Card and Covering the Back Panel VGA Port ..................40

19. Connecting the IDE Cable ............................................................................................41

20. Connecting the Serial ATA Cable .................................................................................42

21. Internal Headers ...........................................................................................................43

22. Back Panel Audio Connectors for Flexible 6-Channel Audio System ............................47

23. Location of Fan Headers...............................................................................................48

24. Connecting 2x12 Power Supply Cables ........................................................................49

25. Location of Other Connectors on Desktop Board D945GNT/D945GTP ........................50

26. Location of the BIOS Configuration Jumper..................................................................51

27. Removing the Battery ...................................................................................................57

28. F2 Key ..........................................................................................................................59

Intel Desktop Board D945GNT/D945GTP Product Guide

viii

Tables

1. Feature Summary...........................................................................................................9

2. Manufacturing Options..................................................................................................11

3. Desktop Boards D945GNT Components ......................................................................13

4. Desktop Boards D945GTP Components.......................................................................15

5. Power Supply Requirements.........................................................................................16

6. Desktop Board D945GNT/D945GTP Memory Configurations.......................................17

7. RJ-45 10/100 Ethernet LAN Connector LEDs ...............................................................20

8. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs ..........................................20

9. Front Panel Audio Header Signal Names for Intel High Definition Audio.......................44

10. AC ’97 Audio Header Signal Names .............................................................................44

11. Hi-Speed USB 2.0 Header Signal Names.....................................................................45

12. IEEE 1394a Header Signal Names...............................................................................45

13. Front Panel Header Signal Names................................................................................46

14. Jumper Settings for the BIOS Setup Program Modes ...................................................51

15. Beep Codes..................................................................................................................65

16. BIOS Error Messages...................................................................................................65

17. Safety Regulations........................................................................................................67

18. Lead-Free Board Markings ...........................................................................................71

19. EMC Regulations..........................................................................................................72

20. Product Certification Markings ......................................................................................74

9

1 Desktop Board Features

This chapter briefly describes the main features of Intel

®

Desktop Board D945GNT/D945GTP.

Table 1 summarizes the major features of the desktop board.

Table 1. Feature Summary

Form Factors

• ATX (12.00” x 9.60”) desktop board D945GNT

• MicroATX (9.60” x 9.60”) desktop board D945GTP

Processor

Support for an Intel

®

processor in the LGA775 package

Main Memory

• Four 240-pin, 1.8 V SDRAM Dual Inline Memory Module (DIMM) sockets

• 667/533/400 MHz single or dual channel DDR2 SDRAM interface

• Designed to support up to 4 GB of system memory

NOTE: System resources (such as PCI and PCI Express*) require physical memory

address locations that reduce available memory addresses above 3 GB. This may

result in less than 4 GB of memory being available to the operating system and

applications. For the latest list of tested memory, refer to the Intel World Wide Web

site at:

http://support.intel.com/support/motherboards/desktop/

Chipset

Intel

®

945G Express Chipset consisting of:

• Intel

®

82945G Graphics and Memory Controller Hub (GMCH) with Direct Media

Interface

• Intel

®

82801GB I/O Controller Hub (ICH7) or 82801GR I/O Controller Hub (ICH7R)

supporting Intel

®

Matrix Storage Technology

• Firmware Hub (FWH)

Graphics

Intel 945G Express Chipset with Intel

®

Graphics Media Accelerator 950

Audio

• Intel 945G Express Chipset

• Intel

®

High Definition Audio interface

• SigmaTel* codec

Expansion

Capabilities

Desktop board D945GNT:

• Four PCI bus add-in card connectors (SMBus routed to PCI bus 2)

• One PCI Express x16 connector

• Two PCI Express x1 connectors

Desktop board D945GTP:

• Two PCI bus add-in card connectors (SMBus routed to PCI bus 2)

• One PCI Express x16 connector

• One PCI Express x1 connector

continued

Intel Desktop Board D945GNT/D945GTP Product Guide

10

Table 1. Feature Summary (continued)

Peripheral Interfaces

• Up to eight USB 2.0 ports

⎯ Four ports routed to the back panel

⎯ Four ports routed to two USB headers

• Four Serial ATA (SATA) channels (3.0 Gb/s), via the ICH7 or ICH7R, one

device per channel

• One IDE interface with ATA-66/100 support (two devices)

• One VGA connector

• One diskette drive interface

• One parallel port

• One serial port

• PS/2* keyboard and mouse ports

BIOS

• Intel

®

Platform Innovation Framework for extensible firmware interface

• 4 Mbit symmetrical flash memory

• Support for SMBIOS

• Intel

®

Rapid BIOS Boot

• Intel

®

Express BIOS Update

Power Management

• Support for Advanced Configuration and Power Interface (ACPI)

• Suspend to RAM (STR)

• Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel

Hardware Management Hardware monitor with:

• Three fan sensing inputs used to monitor fan activity

• Remote diode temperature sensing

• Intel

®

Precision Cooling Technology fan speed control

• Voltage sensing to detect out of range values

Related Links:

For more information about desktop board D945GNT/D945GTP, including the Technical Product

Specification (TPS), BIOS updates, and device drivers, go to:

http://support.intel.com/support/motherboards/desktop/

Desktop Board Features

11

Manufacturing Options

Table 2 shows the manufacturing options for desktop board D945GNT/D945GTP.

Table 2. Manufacturing Options

Option Description

Up to three IEEE 1394a ports

• One port routed to the back panel

• Two ports routed to two IEEE 1394a headers

Peripheral interface

• Intel

®

82562GZ 10/100 Mbit/sec Platform LAN Connect (PLC) device with

RJ-45 connector

• Intel

®

82573E or 82573V Gigabit Ethernet Controller with RJ-45 connector

Hardware management

• Trusted Platform Module

• Intel

®

Active Management Technology

Supported Operating Systems

The desktop board supports the following operating systems:

• Microsoft Windows* 2000

• Microsoft Windows XP Professional

• Microsoft Windows XP Home

• Microsoft Windows XP Media Center Edition 2005

Intel Desktop Board D945GNT/D945GTP Product Guide

12

Desktop Board Components

Figure 1 shows the approximate location of the major components on desktop board D945GNT.

E

F

G

H

R

Intel

82945G

(GMCH)

Intel

82801

(ICH7)

R

Channel B DIMM 1

Channel A DIMM 0

Channel A DIMM 1

Channel B DIMM 0

A

BC

T

D

I

J

K

L

M

N

O

P

Q

R

S

Optical Line Out

(Toslink)

1394a

IEEE

Line In

OM17611

(Optional)

Figure 1. Desktop Board D945GNT Components

Desktop Board Features

13

Table 3. Desktop Boards D945GNT Components

Label Description

A Rear fan header (4-pin, fan speed control)

B PCI Express x1 connectors

C Front panel audio header

D PCI Express x16 connector

E 12 V processor core voltage connector (2x2)

F Rear chassis fan header 1 (3-pin, fan speed control)

G Processor socket

H Processor fan header (4-pin, fan speed control)

I Main power connector (2x12)

J Diskette drive connector

K IDE connector

L Front chassis fan header (3-pin, fan speed control)

M BIOS configuration jumper

N Chassis intrusion header

O Serial ATA connectors

P Front panel header

Q Alternate power LED header

R Hi-speed USB 2.0 headers

S IEEE 1394a headers (optional)

T PCI bus add-in card connectors

Intel Desktop Board D945GNT/D945GTP Product Guide

14

Figure 2 shows the approximate location of the major components on desktop board D945GTP.

R

Intel

82945G

(GMCH)

Intel

82801

(ICH7)

R

Channel B DIMM 1

Channel A DIMM 0

Channel A DIMM 1

Channel B DIMM 0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

OM17612

Optical Line Out

(Toslink)

1394a

IEEE

Line In

(Optional)

Figure 2. Intel Desktop Board D945GTP Components

Desktop Board Features

15

Table 4. Desktop Boards D945GTP Components

Label Description

A Front panel audio header

B PCI bus add-in card connectors

C PCI Express x16 connector

D 12 V processor core voltage connector (2x2)

E Rear fan (3-pin, fan speed control)

F Processor socket

G Processor fan header (4-pin, fan speed control)

H Main power connector (2x12)

I Diskette drive connector

J IDE connector

K Front chassis fan header (fan speed control)

L BIOS configuration jumper

M Chassis intrusion header

N Serial ATA connectors

O Front panel header

P Alternate power LED header

Q Hi-speed USB 2.0 headers

R IEEE 1394 headers (optional)

S PCI Express x1 connector

Related Links:

Go to the following links for more information about:

• Desktop board D945GNT/D945GTP

http://www.intel.com/design/motherbd

http://support.intel.com/support/motherboards/desktop

• Supported processors

http://support.intel.com/support/motherboards/desktop

• Audio software and utilities

http://www.intel.com/design/motherbd

• LAN software and drivers

http://www.intel.com/design/motherbd

Intel Desktop Board D945GNT/D945GTP Product Guide

16

Processor

CAUTION

Failure to use the appropriate power supply (below) and/or not connecting the 12 V (2x2) power

connector to the desktop board may result in damage to the board, or the system may not function

properly.

Table 5. Power Supply Requirements

Platform Compatibility Guide Power Supply Requirements

05B 12V2 rating of 16 A continuous and 19 A peak current for 10mS

05A 12V2 rating of 13 A continuous and 16.5 A peak current for 10mS

04B or 04A ATX12V (version 2.0 or greater) compliant power supply

Desktop board D945GNT/D945GTP supports an Intel processor in the LGA775 package.

Processors are not included with the desktop board and must be purchased separately. The

processor connects to the desktop board through the LGA775 socket.

The supported processors list for desktop board D945GNT/D945GTP is located on the web at:

http://support.intel.com/support/motherboards/desktop/

Related Links:

Go to the following links or pages for more information about:

• Instructions on installing or upgrading the processor, page

32 in Chapter 2

• The location of the two power connectors, page

48 in Chapter 2

Desktop Board Features

17

Main Memory

NOTE

To be fully compliant with all applicable Intel

®

SDRAM memory specifications, the board should

be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your

memory modules do not support SPD, you will see a notification to this effect on the screen at

power up. The BIOS will attempt to configure the memory controller for normal operation.

The desktop board supports dual or single channel memory configurations defined in Table 6.

Table 6. Desktop Board D945GNT/D945GTP Memory Configurations

Memory Speed FSB frequency (MHz) Memory Speed (MHz)

1066 667

800 667

DDR2-667

533 533

1066 533

800 533

DDR2-533

533 533

800 400 DDR2-400

533 400

• Four 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline Memory Module (DIMMs)

connectors with gold-plated contacts

• Unbuffered, non-registered single or double-sided DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC RAM

• 1.8 V memory

• Memory configuration listed below:

⎯ Up to 2.0 GB utilizing 256 Mb technology

⎯ Up to 4.0 GB utilizing 512 Mb or 1 Gb technology

NOTE

System resources (such as PCI and PCI Express) require physical memory address locations that

reduce available memory addresses above 3 GB. This may result in less than 4 GB of memory

being available to the operating system and applications.

Related Links:

Go to the following links or pages for more information about:

• The latest list of tested memory,

http://support.intel.com/support/motherboards/desktop/

• SDRAM specifications, http://www.intel.com/technology/memory/

• Installing memory, page

36 in Chapter 2

Intel Desktop Board D945GNT/D945GTP Product Guide

18

Intel

®

945G Express Chipset

The Intel 945G Express Chipset consists of the following devices:

• Intel 82945G Graphics and Memory Controller Hub (GMCH) with Digital Media Interface

• Intel 82801GB I/O Controller Hub (ICH7) or Intel 82801GR I/O Controller Hub (ICH7R)

supporting Intel Matrix Storage Technology

• Firmware Hub (FWH)

Related Links:

Go to the following link or pages for more information about:

• Audio drivers and utilities

http://support.intel.com/support/motherboards/desktop/

• Installing the front panel audio solution, page

44 in Chapter 2

• The location of audio connectors,

Figure 22 on page 47

Input/Output (I/O) Controller

The super I/O controller features the following:

• One serial port

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style mouse and keyboard interfaces

• Interface for one 1.2 MB or 1.44 MB diskette drive

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

LAN Subsystem

The LAN, with the Intel 82801GB (ICH7) or Intel 82801GR (ICH7R), provides the following

functions:

• Basic 10/100 Ethernet LAN (Intel 82562GZ) or 10/100/1000 Gigabit Ethernet LAN

(Intel

®

82573E or Intel

®

82573V)

• Support for RJ-45 connector with status indicator LEDs

• Programmable transit threshold

• Configurable EEPROM that contains the MAC address

LAN Subsystem Software

For LAN software and drivers, refer to the D945GNT/D945GTP link on Intel’s World Wide Web

site at:

http://support.intel.com/support/motherboards/desktop

Intel Desktop Board D945GNT/D945GTP Product Guide

20

RJ-45 LAN Connector LEDs

Two LEDs are built into the RJ-45 LAN port located on the back panel (see Figure 3).

OM17386

Figure 3. LAN Port LED Locations

Two LEDs are built into the RJ-45 LAN connector.

Table 7 describes the LED states when the

board is powered up and the 10/100 Ethernet LAN subsystem is operating.

Table 7. RJ-45 10/100 Ethernet LAN Connector LEDs

LED Color LED State Indicates

Off LAN link is not established Green

On LAN link is established

Blinking LAN activity is occurring

Off 10 Mbits/sec data rate is selected Yellow

On (steady state) 100 Mbits/sec data rate is selected

Table 8 describes the LED states when the board is powered up and the 10/100/1000 Gigabit

Ethernet LAN subsystem is operating.

Table 8. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs

LED LED Color LED State Indicates

Left Off LAN link is not established

Green

On LAN link is established

Blinking LAN activity is occurring

N/A Off 10 Mb/s data rate

Green On 100 Mb/s data rate

Right

Yellow On 1000 Mb/s data rate

La pagina sta caricando ...

Viglen D945GNT Manuale utente

Questo manuale è adatto anche per

Viglen D945GNT Manuale utente

in altre lingue

Altri documenti