Yamaha DVD-S2300 Manuale del proprietario

Marca: Yamaha

Modello: DVD-S2300

Categoria: Lettori DVD

Tipo: Manuale del proprietario

DVD-S2300

DVD AUDIO/VIDEO SACD PLAYER

LECTEUR DE DVD AUDIO/VIDEO SACD

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

DIGITAL VIDEO

DVD-S2300_G.book Page 1 Friday, October 18, 2002 2:42 PM

CAUTION

To assure the ﬁnest performance, please read this manual

carefully. Keep it in a safe place for future reference.

Install this sound system in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources, vibration,

dust, moisture, or cold. In a cabinet, allow about 2.5cm (1

inch) of free space all around this unit for adequate ventila-

tion.

Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

Do not expose this unit to sudden temperature changes from

cold to hot, nor locate this unit in an environment with high

humidity (i.e., a room with a humidiﬁer) to prevent conden-

sation inside this unit, which may cause an electrical shock,

ﬁre, damage to this unit, and/or personal injury.

Avoid installing this unit in a location where foreign objects

may fall onto this unit or where this unit may be exposed to

liquid dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or dis-

coloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause ﬁre,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall, spilling

the liquid and causing an electrical shock to the user and/

or damage to this unit.

Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause ﬁre, damage to this unit,

and/or personal injury.

Do not plug in this unit to a wall outlet until all connections

are complete.

Do not operate this unit upside-down. It may overheat, possi-

bly causing damage.

Do not use excessive force on switches, knobs and/or cords.

When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

Do not clean this unit with chemical solvents; this might

damage the ﬁnish. Use a clean, dry cloth.

Use only the voltage speciﬁed on this unit. Using this unit

with a higher voltage than speciﬁed is dangerous and may

cause ﬁre, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than as

speciﬁed.

To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

Do not attempt to modify or ﬁx this unit. Contact qualiﬁed

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reason.

When not planning to use this unit for long periods of time

(i.e., vacation), disconnect the AC power plug from the wall

outlet.

Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

Before moving this unit, press STANBY/ON to set the unit in

standby mode, then disconnect the AC power plug from the

wall outlet.

■

For U.K. customers

If the socket outlets in the home are not suitable for the plug sup-

plied with this appliance, the plug should be cut off and an appro-

priate 3 pin plug ﬁtted. For details, refer to the instructions

described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared ﬂexible cord is hazardous if engaged in a live

socket outlet.

■

Special Instructions for U.K.

Model

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam.

When this unit is plugged into a wall outlet, do not place your

eyes close to the opening of the disc tray and other openings or

look inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be con-

nected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth termi-

nal of the three pin plug.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

DVD-S2300_G.book Page 2 Friday, October 18, 2002 2:42 PM

English

INTRODUCTION

FEATURES ............................................................................................2

Playable disc formats...........................................................................2

CHECKING THE ACCESSORIES.....................................................3

INSTALLING BATTERIES IN THE REMOTE CONTROL...........3

CONTROLS AND FUNCTIONS .........................................................4

Front panel / Remote control...............................................................4

Front panel display ..............................................................................6

PREPARATION

CONNECTIONS....................................................................................7

Types of connectors.............................................................................7

Video connections................................................................................8

Audio connections...............................................................................9

Remote control in/out jack ..................................................................9

PLAYING A DISC

PLAYING A DISC...............................................................................10

Before starting playback....................................................................10

Basic operation..................................................................................10

Super Audio CDs...............................................................................12

MP3 playback....................................................................................12

MISCELLANEOUS FUNCTIONS....................................................13

Using disc menus...............................................................................13

Enhancing video quality - Progressive output (U.S.A. model only) .13

DVD-Audio features .........................................................................14

Switching audio tracks, subtitles and angles ..................................15

Program play ....................................................................................16

Random play .....................................................................................17

All group play ...................................................................................17

Bookmarks ........................................................................................18

Repeat play .......................................................................................18

Repeat A-B .......................................................................................19

ON-SCREEN MENU (DVD MODE ONLY).....................................20

Operating the menu bar .....................................................................20

Disc Info bar......................................................................................21

Player Info bar...................................................................................22

Shuttle bar..........................................................................................23

DETAILED SETTINGS

CHANGING THE DVD MODE SETTINGS....................................24

Using the Setup menu........................................................................24

Settings Summary..............................................................................25

Ratings ..............................................................................................28

PCM down conversion ......................................................................28

Speaker settings ................................................................................29

CHANGING THE SACD MODE SETTINGS..................................31

Speaker settings.................................................................................31

Adjusting the brightness of the display .............................................32

Changing the time indicator ..............................................................32

APPENDIX

TROUBLESHOOTING ......................................................................33

GLOSSARY..........................................................................................35

NOTES ON HANDLING DISCS.......................................................36

SPECIFICATIONS..............................................................................37

CONTENTS

■ About this manual

• Illustrations in this manual are based on the

U.S.A. model unless otherwise indicated.

•Paragraphs marked with an y indicator are

tips on operating the unit.

• The user can perform certain operations using

either the remote control or the buttons on the

main unit. This manual frequently explains

how to execute such operations only on the

remote control.

• This manual is printed prior to production.

Design and speciﬁcations of the unit are sub-

ject to change for reasons that include

improved function and operation.

• Illustrations in this manual may differ slightly

from the product or from illustrations used in

the packaging.

• The names of package content items used in

this manual may differ slightly from names

that appear on the product or elsewhere in the

packaging.

DVD-S2300_G.book Page 1 Friday, October 18, 2002 2:42 PM

INTRODUCTION

◆

Built-in high-performance video D/A converter

◆

Output connectors support numerous audio and

home theater component combinations.

Video out:

Component output jacks (two channels)

(U.S.A. and Australian models)

S Video jacks (two channels)

RGB SCART jacks (U.K. and European

models)

Video (Composite) connector (two channels)

Audio out:

Digital: Coaxial jack (one channel)

Optical jack (one channel)

Analog: (L/R) jacks

6ch discrete jacks

SUB OUT/BASS MGMT (man-

agement) jack to boost the low

range

◆

High-end D/A converter for SACD on all eight

channels

◆

D/A converter support for 192kHz 24-bit DVD-

Audio/Video discs

◆

Optimal picture and sound quality, courtesy of

independent circuits for SACD and DVD, and

individual tuning

◆

Dolby Digital and DTS decoders

◆

DCDi Progressive output (U.S.A. model)

◆

MP3 multi-session support

Manufactured under license from

Dolby Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Surround”

are registered trademarks of Digital

Theater Systems, Inc.

“DCDi” is a trademark of Faroudja, a

division of Genesis Microchip, Inc.

This product incorporates copyright protection technology

that is protected by method claims of certain U.S. patents

and other intellectual property rights owned by Macrovi-

sion Corporation and other rights owners. Use of this

Macrovision Corporation, and is intended for home and

other limited viewing uses only unless otherwise autho-

rized by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

This unit can play the disc types associated with the logos

shown below. (Do not attempt to load any other type of

disc into the unit, or the unit may be damaged.)

•DVD mode • SACD mode

This manual refers to disc types using the following indi-

cators:

Notes

• The unit does not support playback of the following discs:

Photo CD, CD-ROM, DVD-ROM, DVD-RAM, SVCD, CDV

• Some discs may fail to play due to recording conditions or disc

characteristics. (If you record discs on a recorder for playback

on this unit, use discs from reliable manufacturers.)

•DVD-RW discs will play only if they are recorded in video for-

mat.

• CD-R/RW, DVD-R/RW, and DVD+R discs will play only if

they are ﬁnalized.

• Do not use non-standard shaped discs (heart-shaped, etc.).

• Some DVD and VCD features described in this manual may

vary in function due to differences in software design from var-

ious manufacturers. Check the instructions for each disc.

• This unit cannot play PAL video discs. (U.S.A. model)

■

Region management information

The unit is designed to support the Region Management

System. Check the regional code number on the disc pack-

age. If the number does not match the unit’s region num-

ber (see table below, or see back of unit), the unit may be

unable to play the disc.

FEATURES

Playable disc formats

DVD-Video DVD-Audio Video CD Audio CD

Super Audio CD

Model

Region number

of this unit

Discs can be played

U.S.A. and Cana-

dian models

ALL

or a mark that includes

the region number

U.K. and Euro-

pean models

ALL

or a mark that includes

the region number

Australian model

ALL

or a mark that includes

the region number

DIGITAL VIDEO

DVD-V DVD-A VCD CD

SACD

DVD-S2300_G.book Page 2 Friday, October 18, 2002 2:42 PM

English

INTRODUCTION

Check your package to make sure it contains the following items:

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

Slide off the battery compartment cover.

Insert two batteries (AA, R06, UM-3 type) ori-

ented properly (+ and –).

Slide the cover back into place.

Replace worn batteries

Worn batteries limit the operating range of the remote con-

trol. Replace both batteries at the same time.

Note

• Replace both batteries if you notice a decrease in the operating

range of the remote control.

• Do not use old batteries with new ones.

• Do not use different types of batteries (such as alkaline and

manganese) together. Read the battery packaging carefully.

Different types of batteries may be the same shape or color.

• If the batteries leak, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact

with clothing, etc. Clean the battery compartment thoroughly

before installing new batteries.

■

Using the remote control

Handling the remote control

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– high humidity or temperature, such as near a heater, stove

or bath;

– dusty places; or

– places subject to extremely low temperatures.

CHECKING THE ACCESSORIES

INSTALLING BATTERIES IN THE REMOTE CONTROL

Remote control Batteries (x2) (AA, R6, UM-3) Audio/Video cable Power cable

30°

Point the remote control at the

sensor, within approximately

6 m (20 feet) of the unit.

Remote control

sensor

DVD-S2300_G.book Page 3 Friday, October 18, 2002 2:42 PM

POWER

Turns the power to the unit on and off.

Disc tray

Load a disc in this tray.

(Front panel),

OPEN/CLOSE (Remote control)

Press to open or close the disc tray.

Press to start playback.

Press to pause.

Press to stop playback.

Press to access the next or previous track or chapter.

Press and hold down to fast forward or fast reverse.

SACD/DVD

Press to switch between DVD mode and SACD mode.

SACD mode indicator

Lights up in SACD mode.

Front panel display

Shows information about the operational status or

default settings of the unit.

PROGRESSIVE indicator (U.S.A. model only)

Lights up during progressive output.

VIDEO OFF indicator

Lights up when the VIDEO OFF function is working.

DVD mode indicator

Lights up in DVD mode.

PHONES LEVEL control

Adjusts the headphone level.

PHONES

Connect headphones here.

CONTROLS AND FUNCTIONS

Front panel / Remote control

12 4

356

wertq

DVD-S2300_G.book Page 4 Friday, October 18, 2002 2:42 PM

English

INTRODUCTION

CONTROLS AND FUNCTIONS

From left:

PLAY MODE

Press to switch between random play, program play,

and normal playback.

REPEAT

Press to repeat playback.

A-B

Press to repeat a section speciﬁed by two points.

MARKER

Press to mark and store location points for future ref-

erence.

From left:

SUBTITLE

Press to select a subtitle language.

AUDIO

Press to select a DVD-Audio language.

ANGLE

Press to change the camera angle on discs recorded

with multiple camera angles.

From top left:

TOP MENU

Press to display the top-level disc menu screen.

Press to display a menu screen.

/ENTER

Press to select and execute a menu item.

ON SCREEN

Press to turn the on-screen icons on or off on the video

monitor.

RETURN

Press to display the previous screen when navigating

the menus.

From left:

(skip)

Press repeatedly to locate the top of the previous or

subsequent tracks.

(slow/search)

Press to fast reverse or fast forward.

Numeric buttons

Press to enter numbers.

CANCEL

Press to cancel a mode or setting.

From left:

GROUP

Press to select a DVD-Audio group.

PAGE

Press to select a DVD-Audio still picture.

PROGRESSIVE button (U.S.A. model only)

Press to toggle between progressive video output and

interlaced video output in DVD mode.

VIDEO OFF

Press to switch video output on and off during DVD-

Audio playback.

From left:

TIME

Press to select the time display in SACD mode.

DIMMER

Press to adjust the brightness of the front panel display

in SACD mode.

MULTI/2CH

Press to toggle between stereo playback and multi-

channel playback in SACD mode during playback of a

super-audio CD that contains both stereo (two chan-

nels) and multi-audio channel data.

SETUP

Press to display the setup menu screen.

DVD-S2300_G.book Page 5 Friday, October 18, 2002 2:42 PM

CONTROLS AND FUNCTIONS

Disc type indicators

The indicator for the type of disc currently being

played lights up.

SACD:

Super audio CD

CD:

Audio CD

DVD AUDIO:

DVD-Audio

DVD VIDEO:

DVD-Video

VCD:

Video CD

MP3:

MP3-format CD-R or CD-RW

Playback indicator

Lights up during playback. Blinks while the resume

function is operating (see “Resume function” on

page 10).

Play mode indicators

The indicator for the current playback mode lights up.

PROG:

Program play

RNDM:

Random play

REP:

Repeat play

REP A-B:

Repeat A-B

REP ALL:

Repeat All

Audio format indicators

The indicator for the disc audio format lights up. If

multiple audio formats are recorded on a disc, the indi-

cator for the format selected by the disc menu or unit

operation lights up.

(Dolby Digital)

PCM (Linear PCM)

P.PCM (Packed PCM)

MULTI (Multi-channel)

2 CH (2-channel)

D.MIX (Down Mix):

This indicator lights up during playback of a DVD-

Audio track that has multiple audio channel signals

(that can be mixed down to two channels).

VSS:

Lights up in virtual surround mode.

Multi-information display

Displays various information, including the disc title,

chapter number, track number, elapsed playing time,

etc.

ANGLE indicator

Lights up during playback of those scenes for which

the DVD features multiple camera angles.

Multi-information display mode indicators

GROUP:

The display indicates a group number.

TITLE:

The display indicates a title number.

TRACK:

The display indicates a track number.

CHAP:

The display indicates a chapter number.

Pause indicator

Lights up when the picture freezes or disc playback

pauses.

Speaker channel indicators

The indicators for the current audio channel light up.

left main;

center;

right main;

RL:

left rear;

SW:

subwoofer;

RR:

right rear

Front panel display

12 3 4

8 7 6

DVD-S2300_G.book Page 6 Friday, October 18, 2002 2:42 PM

English

PREPARATION

Before you make connections, unplug the power cable for the unit and all other components. Do not plug in the power

cables until all connections are complete.

Use the following commercially-available cables to make connections:

CONNECTIONS

Types of connectors

Connect these

audio output jacks

to the audio input

of an AV ampliﬁer.

Connect these video

output jacks to the

video input of an AV

ampliﬁer or the input of

a video monitor.

This jack is reserved for fac-

tory use. Do not connect any

equipment to this jack.

Remote control in/out

jacks

After all connections

are complete, plug the

included power cable

into an AC outlet.

TO AC

OUTLET

Audio cables

Audio pin cable

Coaxial cable

Optical cable

Video pin cable

S Video cable

Component video cable

(for U.S.A. and Australian models)

Video cables

A/V cable

Audio/Video cable

(One cable included in the package)

SCART cable

(for U.K. and European models)

DVD-S2300_G.book Page 7 Friday, October 18, 2002 2:42 PM

CONNECTIONS

You can connect the unit’s video output to a video monitor, or the video input on an AV ampliﬁer (which in turn is con-

nected to a video monitor). Connecting to an AV ampliﬁer enables you to control audio and video using the AV ampliﬁer.

You can set up the AV ampliﬁer using this unit’s OSD (on-screen display).

This unit features several types of video output jacks.

Determine the one compatible with the inputs on your

video monitor. Use the appropriate cable to connect the

unit to an AV ampliﬁer, and the AV ampliﬁer to the moni-

tor.

S VIDEO outputs (1, 2)

The S VIDEO jacks output discrete C and Y signals to

reproduce higher-quality images than normal compos-

ite video. Connect one end of an S Video cable (not

included) to either S VIDEO jack. Connect the other

end to an S Video input on an AV ampliﬁer or video

monitor.

VIDEO outputs (1, 2)

The VIDEO jacks output normal composite video sig-

nals. Use the yellow plugs on an audio/video cable to

connect either VIDEO jack to a video input on an AV

ampliﬁer or video monitor.

The same signal is output from VIDEO 1 and VIDEO

2, enabling connection to two devices (e.g., a monitor

and an AV ampliﬁer) simultaneously.

COMPONENT outputs

(U.S.A. and Australian models only)

These jacks output three discrete CCY signals (“com-

ponent video”) to reproduce a higher-quality image

than S Video.

(U.S.A. model only)

This unit features a DCDi circuit (with the latest con-

tour correction technology) and progressive output,

which produces very smooth and natural high-quality

pictures even on a big screen. Use a component video

cable (not included) to connect the COMPONENT

output jacks to the component video input connectors

on an AV ampliﬁer or video monitor.

AV connector

(U.K. and Europe models only)

If your monitor has only one jack for video input, you

can use the SCART output jack on this unit to connect

the unit directly to the monitor. This connection pro-

vides the best picture quality.

Note

• Do not connect this unit to a video monitor through a

video cassette recorder. If you do so, the picture may not

play back properly due to the copyright protection tech-

nology incorporated in this unit.

Video connections

Monitor

AV ampliﬁer

To S VIDEO

To VIDEO

To COMPONENT

VIDEO

MONITOR OUT

DVD-S2300_G.book Page 8 Friday, October 18, 2002 2:42 PM

English

CONNECTIONS

PREPARATION

Select connectors that are compatible with your ampliﬁer and appropriate for your requirements.

DIGITAL OUT jacks

• Connect the OPTICAL jack to the ampliﬁer’s optical

digital input using ﬁber optic cable (not included)

-or-

• Connect the COAXIAL jack to the ampliﬁer’s coaxial

digital input using coaxial digital cable (not included).

Note

• No audio signal is output from DIGITAL OUT during

SACD playback. Use connection

below.

MIXED 2CH jacks

Use the included audio/video pin cable to connect

these jacks to analog stereo input jacks on the ampli-

ﬁer. Connect the white plug to the L jack. Connect the

red plug to the R jack. (The yellow plug is used for the

video signal.)

6CH DISCRETE jacks

Use an audio pin cable

(not included)

to connect these

jacks to the corresponding channel inputs (such as

MAIN L/R, CENTER) on the ampliﬁer (often labelled

“6CH INPUT”).

Connect the SUBWOOFER jack to the subwoofer

input on the ampliﬁer. This jack outputs a more natu-

ral, high-ﬁdelity low range relative to the SUB OUT/

BASS MGMT jack explained below. However, during

playback of a two-channel (stereo) source, the sub-

woofer does not output any sound due to lack of LFE

(low-frequency effects assigned to a subwoofer).

★

SUB OUT/BASS MGMT jack

SUB OUT/BASS MGMT aggregates and outputs the

low ranges of all channels. An alternative to 6CH DIS-

CRETE SUBWOOFER output, this jack outputs a

powerful and supple sound even when the main speaker

is small (with a woofer diameter of 16cm or less).

Use an audio pin cable (not included) to connect the

SUB OUT/BASS MGMT jack to the subwoofer input

on the ampliﬁer.

These jacks are used in custom installations to transmit

remote control signals via cable.

• Connect REMOTE CONTROL IN to an output on your

remote control system.

• Connect REMOTE CONTROL OUT to a remote con-

trol input on another component to enable system con-

trol.

Audio connections

Using AV ampliﬁer’s 6.1 channel decoding

(DVD-Video) and surround effects:

Playing SACD or DVD multi-channel audio:

Remote control in/out jack

12 3

★

Speakers

AV ampliﬁer

DIGITAL INPUT

Either one

To OPTICAL

To AUDIO

(analog ste-

reo input)

To 6CH INPUT

To COAXIAL

DVD-S2300_G.book Page 9 Friday, October 18, 2002 2:42 PM

PLAYING A DISC

Before playing a disc, you must connect the unit’s audio

and video output jacks to an AV ampliﬁer or other system

component (refer to pages 8 and 9).

Note

• If you digitally connect the unit to an ampliﬁer that does not

feature a DTS decoder, set DTS DIGITAL SURROUND to

PCM (factory default) in the Setup/Audio menu. Otherwise,

unprocessed digital signal noise will be output that may dam-

age your hearing or speakers.

Press POWER to turn on the power.

Press OPEN/CLOSE to open the disc tray.

Load a disc into the disc tray.

If necessary, press SACD/DVD to change the

mode.

For more information, refer to “Switching disc play

mode” on page 10 (below).

Press

The disc tray closes and playback starts.

• If one of the following indicators is displayed

refer to “Using disc menus” on

page 13.

• When the unit ﬁnishes playing a DVD, it stops playback or dis-

plays a menu screen.

Note

• The unit cannot play CD-R or CD-RW discs that have not been

ﬁnalized. Be sure to ﬁnalize discs on a CD recorder before

playing them in this unit. (The term “ﬁnalize” refers to an

audio process for CD-Rs or CD-RWs that prepares them for

play on supporting players.)

■

Switching disc play mode

While the unit is stopped or the disc tray is

open, press SACD/DVD.

The unit includes independent playback circuits for

SACDs and DVDs to optimize use of each disc type.

•To play an SACD, switch to SACD mode.

•To play other types of discs, switch to DVD mode.

Use SACD mode to play .

The SACD mode indicator lights up.

Use DVD mode to play , , , and

The DVD mode indicator lights up.

• If you are playing a hybrid disc that contains both SACD for-

mat data and conventional CD format data, select SACD mode

to play the SACD format data, or DVD mode to play the CD

format data.

■

To stop playback

Press

■

Resume function

The unit retains memory of the point at which you pressed

the

button as long as the power to the unit is turned on.

During this time, the

indicator will ﬂash on the display.

Press

to resume playback from the stop point.

PLAYING A DISC

Before starting playback

Basic operation

POWER

SACD/DVD

OPEN/CLOSE

DVD/SACD mode

indicator

DVD-A DVD-V

VCD

SACD

DVD-A DVD-V

VCD

DVD-S2300_G.book Page 10 Friday, October 18, 2002 2:42 PM

English

PLAYING A DISC

To clear the memory, press

again. The

indicator dis-

appears. (When a DVD-Video disc is played, a

chapter

review screen will appear.)

Note

• Opening the disc tray cancels the resume function.

■

Chapter review function

This function plays the ﬁrst few seconds of each chapter

(from the beginning of the title up to the memorized point)

so you can review previous chapters.

Press

while the chapter review message is displayed on

screen. (If you do not press

, after a while the message

disappears and playback resumes.)

Notes

• This function may not work on some DVDs.

• Canceling the resume function also clears the chapter review

function.

■

After operating the unit

Press

to open the disc tray. Remove the disc, then press

POWER to turn off the unit.

■

Skip

On the remote control, press

(or

) to skip forward

(or backward).

On the front panel, press

(or

) to skip for-

ward (or backward).

Press

on the remote control or

on the front

panel to locate the top of the current chapter or track.

Note

• VCDs that use playback control (page 13) may not allow the

skip operation to function as described above.

■

Selecting a track

Key in the desired track number using the numeric but-

tons.

Example (to select track 27):

Press

≥

10.

Press 2.

Press 7.

Press

≥

10 twice.

Press 7.

■

On the remote control, press

(or

) to search for-

ward (or backward).

-or-

On the front panel, press and hold

(or

) to

search forward (or backward).

•To increase search speed, repeatedly press (or press and hold)

r or e on the remote control, or press and hold r/y or

t/e on the front panel.

■ Pause

Press d during playback.

To resume playback, press w.

■ Frame advance/reverse

To advance or reverse frames: While the pic-

ture is still or in pause mode, press the cur-

sor buttons (ll

, hh

•To return to normal playback, press w.

• Press the cursor buttons (l, h) repeatedly, or

press and hold them, to advance or reverse frames

at increasing rates of speed.

• Pressing d also advances a few frames.

• On certain DVD-Audio discs, frames may advance

or reverse only during the video portions of the

disc.

Note

• The Video CD format does not permit reverse navigation.

DVD-V

≥10

VCD CDSACD

VCD CD

SACD

VCDDVD-A DVD-V

DVD-S2300_G.book Page 11 Friday, October 18, 2002 2:42 PM

PLAYING A DISC

■

Slow

To play a disc slowly, while the picture is still

or paused:

Press

on the remote control.

-or-

Press and hold

(or

) on the

front panel.

•To return to normal playback, press

•To increase the speed, repeatedly press (or press

and hold)

on the remote control; or press

and hold

on the front panel.

Note

• The Video CD format does not permit reverse navigation.

There are three types of Super Audio CDs:

•a

2-channel disc

that contains stereo audio

•a

multi-channel disc

that includes up to six (6) channels

of data

•a

combination disc

that includes a 2-channel data area

and a multi-channel data area.

■

Switching between different chan-

nel areas

Select your desired area for playback on a combination

disc.

While the unit is stopped, press MULTI/2CH.

When the multi-channel area is selected, the MULTI indi-

cator lights up on the display. When the 2-channel area is

selected, the 2CH indicator lights up on the display.

The unit can play MP3 format audio that was recorded by

a computer onto CD-R or CD-RW.

• If an MP3 ﬁle is of poor quality, playback may not be possible.

Disc Structure Example

MP3 discs are different than standard audio CDs.

The MP3 format is so compact and efﬁcient that the equiv-

alent of several albums or standard audio CDs may be

stored on a single MP3 disc.

The unit creates a folder for the “Title” and a ﬁle for each

“Chapter.”

Starting playback from a selected chapter

Select a chapter using the numeric buttons (see “Selecting

a track” on page 11), then press ENTER to play the chap-

ter.

Repeat play

To repeat playback, use chapter repeat or title repeat (see

page 18 for details).

Notes

• This unit can play MP3 discs recorded at bit rates of 32kbps to

320kbps and sampling frequencies of 44.1kHa and 48kHz. (A

sampling frequency of 32kHz is not supported.)

• Program play and random play are unavailable on MP3 discs.

• Chapters may not play in the order selected at the time of

recording.

Disc info icons (on-screen) during playback

Super Audio CDs

VCDDVD-A DVD-V

2-channel area

Multi-channel area

MULTI/2CH

MP3 playback

Root directory

: Title (Folder)

: Chapter (File)

1/ 59

0 : 01

Total chapter number

Current chapter Elapsed play time (for display

only)

DVD-S2300_G.book Page 12 Friday, October 18, 2002 2:42 PM

English

PLAYING A DISC

Many discs include menu screens that enable you to con-

trol special features, such as skipping to a favorite title or

chapter, or selecting an audio language or subtitle lan-

guage for a movie. This section provides general instruc-

tions on operating these screens.

Press TOP MENU or MENU during playback.

The video monitor displays a menu.

• On certain discs, the menu appears automatically

when you start playback.

Press the cursor buttons (

) to

select the desired item, then press ENTER.

(If another menu screen appears, repeat this step.)

■

Video CD playback control (PBC

menu play)

Video CDs that feature “playback control” allow you to

navigate certain scenes or information by menu.

This manual refers to the use of menus to control Video

CD playback as “menu play.”

Numeric buttons:

Press to select the desired item.

RETURN:

Press to display the initial menu screen.

(PLAY):

Press to play the selected item.

Press to display the next screen.

Press to display the previous screen.

(STOP):

Press while a menu is displayed to

cancel playback control.

Notes

• Playback control is automatically canceled during program

play or random play.

• Certain discs may not respond as described above.

The unit’s COMPONENT video jack can output progres-

sive signals to a progressive signal compatible monitor for

an extra high-quality picture.

Press PROGRESSIVE.

The PROGRESSIVE indicator lights up.

To cancel this feature, press PROGRESSIVE again.

Notes

• If the screen shifts off center during progressive output, refer to

“Adjusting the screen position,” described below.

• When playing 4:3 aspect video on a 16:9 aspect wide-screen

monitor using progressive output, the picture may stretch hori-

zontally to ﬁll the screen. In this case, change the aspect ratio

to suit the monitor. If this is not possible, turn the progressive

feature off. (The progressive output will switch to interlace

output.)

• When the progressive function is working, video signals are

output from only the COMPONENT output jacks.

MISCELLANEOUS FUNCTIONS

Using disc menus

TOP MENU

RETURN

, , ,

/ ENTER

Numeric

buttons

DVD-V

DVD-A

VCD

Enhancing video quality - Progres-

sive output (U.S.A. model only)

PROGRESSIVE

PROGRESSIVE indicator

DVD-S2300_G.book Page 13 Friday, October 18, 2002 2:42 PM

MISCELLANEOUS FUNCTIONS

■

Adjusting the screen position

(when using progressive output)

Progressive signals output from the unit may shift off cen-

ter on certain monitors. To adjust the screen position, use

the remote control as follows:

Press

to pause playback.

Follow step 1 under “Operating the menu

bar” on page 20 to display the Picture set-

ting.

Press the cursor buttons (

) to select the

right-most icon ( ).

Adjust the screen position.

To move the image to the left, press numeric button 1.

To move the image to the right, press numeric button

• Pressing numeric button 2 after pressing 1 or 3

sets the screen back to the original position.

•To check whether the picture is centered, switch to

normal output (press PROGRESSIVE to turn the

indicator off).

Save the adjusted position.

First press

, then press SETUP to display the setup

menu. Press SETUP again (or RETURN) to save the

position. (Even if you skip this step, the position will

be saved until you turn the power off.)

■

Playing a track in a speciﬁc group

Press GROUP.

The video monitor displays group and track icons.

Press the cursor buttons (

) to select a

group number, then press ENTER.

Press the cursor buttons (

) to select a

track number, then press ENTER.

The selected track starts to play.

•You can also use the numeric buttons to select a group and a track.

■

Playing bonus groups

Some discs contain bonus groups that require a four-digit

password to gain access. In this case, consult the disc

jacket and other packaging for information.

While playback is stopped, press GROUP.

The video monitor displays group and track icons.

Press the cursor buttons (

k, n) to select a

bonus group, then press ENTER or the cur-

sor button (h).

3 Enter a four-digit password using the

numeric buttons, then press ENTER.

4 Press the cursor buttons (k, n) to select a

track, then press ENTER.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEF-

INITION TELEVISION SETS ARE FULLY COMPATIBLE

WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO

BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PRO-

GRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOM-

MENDED THAT YOU SWITCH THE CONNECTION TO

THE “STANDARD DEFINITION” OUTPUT. IF THERE ARE

QUESTIONS REGARDING YOUR VIDEO MONITOR COM-

PATIBILITY WITH THIS UNIT, PLEASE CONTACT OUR

CUSTOMER SERVICE CENTER.

This unit is compatible with the complete line of

YAMAHA projectors, including the DPX-1, LPX-500, PDM-1

and DPX-1000.

Example:

Press 3 to move to the right.

DVD-Audio features

DVD-A

, , ,

/ ENTER

PAGE

GROUP

DVD-S2300_G.book Page 14 Friday, October 18, 2002 2:42 PM

English

PLAYING A DISC

MISCELLANEOUS FUNCTIONS

■

Changing pages

DVD-Audio discs can contain information pages that can

include photo galleries, artist biographies, lyrics, etc.

Press PAGE to turn the page. (The page number will

update on the display when you change pages.)

Some discs are encoded with several audio tracks, multi-

lingual subtitles or multiple camera angles. Refer to the

disc jacket to learn which features are supported.

■

Changing audio tracks

You can select different audio track languages and/or for-

mats, if they are available on a disc.

Press AUDIO during playback.

• Press AUDIO repeatedly to step through all audio

tracks on a disc. The cursor buttons (

) and the

numeric buttons also change tracks.

• If you change audio tracks while playing a non-video portion

of a DVD-Audio disc, playback begins at the beginning of the

track.

• On a DVD-Audio disc, track 2 appears on the front display

even if the disc contains only one audio track.

•You can also use the button to turn the vocals on or off on

karaoke discs. See the disc instructions for details.

■

Selecting a subtitle language

Press SUBTITLE during playback.

• Press SUBTITLE repeatedly to step through all

subtitles on the disc. The cursor buttons (

) and

the numeric buttons also change subtitles.

• “- -” is displayed if a disc does not include a subtitle.

Note

• Subtitles may not be displayed immediately.

Turning subtitles on or off

Press SUBTITLE.

Press the cursor button (

(, ONLY)

Press the cursor buttons (

) to select ON

or OFF.

■

Changing angles

Press ANGLE.

• Press ANGLE repeatedly to step through all

angles recorded on the disc. The cursor buttons (

) and the numeric buttons also change angles.

■

Turning the icons off

Press RETURN.

Note

• Certain discs require that you use a disc menu to change audio

tracks, subtitles or angles.

Switching audio tracks, subtitles

and angles

DVD-V VCDDVD-A

RETURN

AUDIO

ANGLE

SUBTITLE

, , ,

Numeric

buttons

96k24b

LPCM

This icon appears on the video

monitor.

ENG

This icon appears on the video monitor.

DVD-A

DVD-V

This icon appears on the video monitor.

DVD-S2300_G.book Page 15 Friday, October 18, 2002 2:42 PM

MISCELLANEOUS FUNCTIONS

Enjoy listening to your favorite tracks in any order. This

unit enables you to program sequence for up to 32 tracks

from disc.

Press

to stop playback.

Press PLAY MODE repeatedly to select the

program screen.

Each time you press PLAY MODE, the screen

changes as follows:

Press the button repeatedly to light up the indicators in the

following order:

Example: (Program play)

Note

• On combination discs (which include 2-channel and multi-

channel areas), you can program tracks only in the currently-

selected area.

Press numeric buttons to select the track.

Press

to start playback.

•You can also use numeric buttons to select a group or track.

• The “All group play” screen (playback of all groups in order) is

added to step 2.

• In step 4, press the cursor buttons (

) to select a group, then

press ENTER. Press the cursor buttons (

) again to select a

track, then press ENTER.

■

Changing or adding to the pro-

gram during program play

Press

repeatedly to stop program play.

Press the cursor buttons (

) to select the

desired track order position.

Press the numeric buttons to enter a track

number.

■

Canceling programmed tracks

Press

repeatedly to stop program play.

Press the cursor buttons (

) to select a

track to cancel.

Press CANCEL.

Note

• If you program a Video CD track (ver. 2.0), playback con-

trol is canceled during program play.

■ Navigating up and down pages on

the program screen

Press e to move up the page, or press r to move down

the page.

■ Exiting programming mode

1 Press aa

repeatedly to stop program play.

2 Press PLAY MODE twice.

•Turning off the power or opening the disc tray will

cancel all programs.

Program play

CDDVD-A VCDSACD

CANCEL

PLAY MODE

, , ,

/ ENTER

Numeric

buttons

CDDVD-A VCD

PLAY MODE

Choose a track, then press ENTER.

No Track

Press PLAY to start

Play

0:00

Time

Clear

Clear all

Total time

ENTER

SELECT

RETURN

Video monitor display (example)

Program screen (Program play mode)

Playing in desired order

Random screen (Random play mode)

Playing in random sequence

Return to normal playback

SACD

PROG (Program play)

RNDM (Random play)normal playback

DVD-A

DVD-S2300_G.book Page 16 Friday, October 18, 2002 2:42 PM

English

PLAYING A DISC

MISCELLANEOUS FUNCTIONS

In random play mode, the unit plays all tracks on the disc

in random order.

Press

to stop playback.

Press PLAY MODE repeatedly.

The “RNDM” indicator lights up on the front panel

display.

Press

to start random play.

■

Canceling random mode

Press

repeatedly to stop playback during

random play.

Press PLAY MODE.

The “RNDM” indicator disappears.

• Opening the disc tray also cancels this mode.

Notes

• When the unit is in random mode, Video CD playback

control is canceled.

• Up to 100 tracks can be programmed for SACD random

play.

In step 2 of “Random play,” press the cursor buttons

(

) to select a group, then press ENTER.

Example: DVD-Audio (a disc with up to two groups)

•You can select multiple groups.

• Use the numeric buttons to select a group.

To cancel a selection, press the cursor buttons (

) to

select the group(s), then press CANCEL or ENTER.

•You can also cancel a group by entering its group number

using the numeric buttons.

Press

to stop playback.

Press PLAY MODE.

Press

Random play

CDDVD-A VCDSACD

PLAY MODE

CANCEL

ENTER

All group play

DVD-A

All 1 2

Choose a group or groups.

Random Playback

Press PLAY to start

ENTER

SELECT

RETURN

DVD-A

PLAY MODE

DVD-S2300_G.book Page 17 Friday, October 18, 2002 2:42 PM

MISCELLANEOUS FUNCTIONS

The Bookmark feature allows you to mark up to ﬁve

points (locations), enabling you to return quickly to those

points.

Press MARKER.

Press the cursor buttons (

) to select

one of ﬁve asterisks.

The selected asterisk is highlighted.

Press ENTER.

The selected asterisk changes to the bookmark num-

ber.

■

Playing from a marked point

Press the cursor buttons (

) to select a bookmark

number, then press ENTER.

■

Clearing a bookmark

Press the cursor buttons (

) to select a bookmark

number, then press CANCEL.

Note

• When you open the disc tray or turn the unit off, all bookmarks

are cleared.

To select Repeat mode, during playback

press REPEAT.

Each time you press the REPEAT button, the repeat

mode changes as follows.

During repeat play, the following indicators light up:

The selected repeat mode name scrolls across the multi-

information display.

Notes

• Repeat play may not work properly on all DVD-Video discs.

• Repeat play may not work during menu play of VCDs that fea-

ture playback control.

•For Super Audio CDs, only the indicators on the unit’s display

will light up.

• If you select “All” repeat for a disc that has a 2-channel area

and a multi-channel area, only tracks in the currently-selected

area will repeat.

Bookmarks

VCDDVD-A CDDVD-V

MARKER

CANCEL

/ ENTER

This icon appears on the video monitor.

Highlighted

Bookmark number

Repeat play

Indicators on

the monitor

Indicators on the unit

display

CHAPTER C REP

TITLE T REP

TRACK T REP

ALL A REP, ALL

GROUP G REP

VCDDVD-A CDDVD-VSACD

REPEAT

VCD

DVD-A

DVD-V

SACD

CHAPTER

TITLE

NORMAL PLAYBACK

TRACK

GROUP

NORMAL PLAYBACK

TRACK

ALL (Entire disc)

NORMAL PLAYBACK

This icon appears on the video monitor.

DVD-S2300_G.book Page 18 Friday, October 18, 2002 2:42 PM

La pagina sta caricando ...

Yamaha DVD-S2300 Manuale del proprietario

Marca: Yamaha

Modello: DVD-S2300

Categoria: Lettori DVD

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Yamaha DVD-S2300 Owner's manual
français: Yamaha DVD-S2300 Le manuel du propriétaire
Deutsch: Yamaha DVD-S2300 Bedienungsanleitung
Nederlands: Yamaha DVD-S2300 de handleiding
dansk: Yamaha DVD-S2300 Brugervejledning
svenska: Yamaha DVD-S2300 Bruksanvisning
Türkçe: Yamaha DVD-S2300 El kitabı
română: Yamaha DVD-S2300 Manualul proprietarului

Yamaha DVD-S2300 Manuale del proprietario

Yamaha DVD-S2300 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti