Pioneer Music Mixer SVM-1000 Manuale utente

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’uso

Handleiding

Manual de instrucciones

SOUND & VISION MIXER

TABLE DE MIXAGE SON ET VIDÉO

SOUND & VISION-MISCHPULT

MIXER AUDIO E VIDEO

MENGPANEEL VOOR GELUID & BEELD

CONSOLA DE MEZCLA DE SONIDO Y VISIÓN

АУДИО И ВИДЕО МИКШЕР

SVM-1000

01_SVM-1000_B_En.book 1 ページ２００７年１１月２６日　月曜日　午後１時４４分

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

D3-4-2-1-2-2_B_En

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should the

fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows ;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

Operating Environment

Operating environment temperature and humidity:

+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment.

D3-4-2-1-7a_A_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058_A_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-1a_A_En

CAUTION

The POWER switch on this unit will not completely

shut off all power from the AC outlet. Since the

power cord serves as the main disconnect device for

the unit, you will need to unplug it from the AC outlet

to shut down all power. Therefore, make sure the

unit has been installed so that the power cord can

be easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a_A_En

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filled

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture.

D3-4-2-1-3_B_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 5 cm at rear, and 3 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

This product complies with the Low Voltage Directive

2006/95/EC and EMC Directive 2004/108/EC.

D3-4-2-1-9a_A_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished

reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the

explanatory drawings. However the method of connecting and operating the unit is the same.

01_SVM-1000_B_En.book 2 ページ２００７年１１月２６日　月曜日　午後１時４４分

3

En

English

Installing the SVM-1000 in an EIA rack

The screw holes located on the left and right ends of the front

panel (within the side cover) match the 19-inch EIA rack.

• Remove the 10 screws (five screws each located on the left and

right sides of the unit) before installing the unit to the rack.

• Holes for rack installation can be located when the side covers

are removed.

• Attach the unit to the rack using screws of the appropriate size

(screws not provided with the unit).

• When installing the unit in a rack, take care to avoid pinching

your fingers.

Note

• Never place this unit directly above a power amplifier, as the

heat given off by the amplifier might result in damage to the unit.

Placing the unit directly above a power amplifier might also

result in ham radio signals being picked up or in other types of

interference.

• Allow at least 1U (43.7 mm) space between this component and

the one mounted above it, so as to assure that the cords

connected to this unit's input/output connectors and terminals

do not touch the component above.

• Always be sure to remove the unit from its rack before shipping.

• When moving the unit while still installed in its rack, exercise

caution to avoid subjecting the unit to shocks or vibration.

Contents

CONFIRM ACCESSORIES..............................................4

CAUTIONS REGARDING HANDLING............................4

Location.......................................................................................... 4

Cleaning the Unit........................................................................... 4

Disclaimer ...................................................................................... 4

About Copyright............................................................................. 4

FEATURES ....................................................................4

NAMES AND FUNCTIONS OF PARTS ...........................6

CONNECTION PANEL ................................................................... 6

OPERATION PANEL ...................................................................... 7

CONNECTIONS...........................................................10

CONNECTING INPUTS................................................................ 10

CONNECTING OUTPUTS ............................................................ 11

CONNECTING MICROPHONE AND HEADPHONES ............... 12

CONNECTING THE POWER CORD............................................ 12

BASIC OPERATIONS...................................................13

FADER CURVE SELECTION ....................................................... 14

USING THE VIDEO CONTROL FUNCTIONS .................15

OPERATING THE VIDEO CROSS FADER .................................. 15

OPERATING THE VIDEO CHANNEL SWITCH ........................... 15

OPERATING IN THE VIDEO SOLO MODE ................................. 16

VIDEO MIX EFFECTS CHART...................................................... 16

USING THE EFFECT FUNCTION...................................17

USING BEAT EFFECTS ................................................................ 17

USING TOUCH EFFECTS............................................................. 19

USING TEXT EFFECTS ................................................................. 20

EDITING TEXT............................................................................... 22

DISPLAYING/HIDING THE MASTER MONITOR ........................ 22

EFFECT LIST.................................................................................. 23

USING THE JPEG VIEWER.......................................... 31

BEFORE USING THE JPEG VIEWER...........................................31

JPEG VIEWER SETUP ..................................................................31

THE VIDEO EQUALIZER FUNCTION............................34

SET UP THE VIDEO EQ................................................................34

TURNING THE EQUALIZER ON/OFF ..........................................34

FADER START FUNCTION .......................................... 35

CROSS FADER START PLAY AND BACK CUE PLAY................35

PERFORM UTILITY SETUP .......................................... 36

MIDI SETTINGS ............................................................................36

SYNCHRONIZING AUDIO SIGNALS TO EXTERNAL

SEQUENCER, OR USING SVM-1000 INFORMATION TO

OPERATE AN EXTERNAL SEQUENCER ....................................36

MIDI CODE LIST ...........................................................................37

PERFORM VIDEO MONITOR SETUP .........................................41

KEYBOARD LANGUAGE SETUP.................................................41

HARDWARE SETUP....................................................42

MIC SETTING ................................................................................42

SYSTEM SETTINGS.......................................................................42

MASTER OUT SETTINGS .............................................................43

LCD SETTINGS..............................................................................43

MONITOR OUT SETTINGS...........................................................43

TOUCH PANEL SETTINGS...........................................................44

RETURNING TO DEFAULT SETTINGS ........................................44

ENDING HARDWARE SET UP....................................................44

TROUBLESHOOTING .................................................. 45

ABOUT THE LCD SCREEN ..........................................................46

ABOUT MINIATURE FLUORESCENT TUBE TECHNOLOGY .....46

SPECIFICATIONS........................................................ 47

Screws

Side cover

01_SVM-1000_B_En.book 3 ページ２００７年１１月２６日　月曜日　午後１時４４分

CONFIRM ACCESSORIES / CAUTIONS REGARDING HANDLING / FEATURES

4

En

CONFIRM

ACCESSORIES

Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CAUTIONS REGARDING

HANDLING

Location

Install the unit in a well-ventilated location where it will

not be exposed to high temperatures or humidity.

• Do not install the unit in a location which is exposed to direct

rays of the sun, or near stoves or radiators. Excessive heat

can adversely affect the cabinet and internal components.

Installation of the unit in a damp or dusty environment may

also result in a malfunction or accident. (Avoid installation

near cookers etc., where the unit may be exposed to oily

smoke, steam or heat.)

• When the unit is used inside a carrying case or DJ booth,

separate it from the walls or other equipment to improve heat

radiation.

Cleaning the Unit

• Use a polishing cloth to wipe off dust and dirt.

• When the surfaces are very dirty, wipe with a soft cloth

dipped in some neutral cleanser diluted five or six times with

water and wrung out well, then wipe again with a dry cloth.

Do not use furniture wax or cleaners.

• Never use thinners, benzene, insecticide sprays or other

chemicals on or near this unit, since these will corrode the

surfaces.

Disclaimer

• Microsoft and Windows are registered trademarks of

Microsoft Corporation, registered in the U.S. and other

countries.

Apple and Mac OS are trademarks of Apple Inc., registered

in the U.S. and other countries.

• The typefaces included herein are partially developed by

DynaComware Taiwan Inc.

About Copyright

This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by

Macrovision Corporation, and is intended for home and other

limited consumer uses only unless otherwise authorized by

Macrovision. Reverse engineering or disassembly is prohibited.

In the event that the above noted copy protection function operates

in any channel, some effects (DELAY, ECHO, ROLL, REVERSE

ROLL) will not function.

FEATURES

4-Channnel Music and Video Synchromix

Most conventional image mixing devices are limited to the simple

mixing of two video images, but Pioneer’s own uniquely developed

video blending technology makes it possible to simultaneously mix

up to four channels of music and video. Since the synchro control

allows the use of fader and equalizers with each channel, a new,

wider range of performances is possible with the sensation of

using conventional DJ mixers.

“AV Effects” support a wide variety of new

performance styles by synchronizing music and

video.

Equipped with AV Effects that synchronize music effects and video

effects on the large 11-inch LCD touch panel display, allowing up

to 30 types of effects to be applied to your music and images.

1 Beat effect: Automatically detects the tempo of the currently

playing track, and applies effects to music and image in synch

with the beat.

2 Touch effect: By directly touching the image displayed on the

large LCD touch panel, effects can be applied to music and

video more intuitively.

3 Text effect: Text messages created in synchronization with the

automatically detected track tempo can be displayed with

effects. Text messages can be entered either by the built-in

keyboard or a common USB keyboard.

“JPEG VIEWER” allows use of images stored in

external memory for live performances

Up to eight JPEG files saved on SD memory cards or USB memory

devices can be downloaded and used as a still image sampler. By

applying effects or mixing with other videos and images such as

the name of the DJ or event, or graphic logos, you can broaden the

potential of your performance. Additionally, JPEG files can be

loaded and displayed as an automatic slide show.

Digital sound/video system for high quality sound

and image

1 96 kHz/24-bit sampling digital system for high sound quality

Analog signals input from a DJ player are passed through the

shortest possible signal path and digitized using a high-fidelity A/D

converter with 96 kHz/24-bit sampling, producing optimum quality

for digital mixing. Mixing is performed by a 32-bit DSP to eliminate

any degradation in sound quality, while simultaneously using ideal

filtering to produce optimum sound for DJ play.

In order to realize the greatest possible response, the unit also

features a high-rigidity chassis and double-shield construction to

suppress unwanted vibrations that might adversely effect sound

quality, together with a powerful power section and other high-

fidelity technology, thus producing clear, powerful club sounds.

2 High-performance video IC digital system for high image

quality

Video signals input through the high-performance ADC are

processed through a high-performance video DSP rated at 600

MHz/32-bit/4800 MIPS (Million Instructions Per Second), thus

preserving the original image’s dynamic range while also

suppressing unwanted noise and producing images with high

fidelity and quality. The same high quality has also been realized

for video effects that normally tend to be a source of image

degradation.

01_SVM-1000_B_En.book 4 ページ２００７年１１月２６日　月曜日　午後１時４４分

FEATURES

5

En

English

Improved design and operability for new club

culture

Based on the concept of creating “a design that fascinates,” the

boxy-shape of previous DJ mixers has been restyled toward an

edgier and more solid design. Great attention has been given to

details of materials and design, such as employing an

“illumination display” on the rear panel visible from the dance

floor.

Operating panel design emphasizes convenience for

simultaneous performances of music and video, with a “channel

symmetry layout” centered around the 11-inch LCD touch panel.

By arranging each channel section symmetrically, further

improvements in operability have been made to assist easy mixing

between music and video, so that effects can be enabled

dynamically from the LCD touch panel.

Other DJ/VJ performance functions made possible

through digital technology

1 “VIDEO TRIM” allows adjustment of the luminance of images

input to each channel.

2 “VIDEO EQUALIZER” assigns parameters such as [RGB],

[CONTRAST], [HUE], and [SATURATION] to the equalizer,

allowing synchronization of audio equalizing and video

controls.

3 “AV SYNC” allows the user to select whether audio and video

controls are linked or adjusted separately.

4 “VIDEO MONITOR SELECTOR” allows the user to choose

whether the monitor video output shows master only, all

channels, master and each channel, master mixing inversion,

etc.

5 “FULLY ASSIGNABLE MIDI” allows control of DJ effecter, DJ/

VJ application programs, and other external components.

01_SVM-1000_B_En.book 5 ページ２００７年１１月２６日　月曜日　午後１時４４分

NAMES AND FUNCTIONS OF PARTS

6

En

NAMES AND FUNCTIONS OF PARTS

CONNECTION PANEL

1 POWER switch

2 PHONO input connectors

RCA type phono level (MM cartridge) input connectors.

Do not use for inputting line level signals.

3 DVD/LINE input connectors

RCA type line level audio input connectors.

Use to connect a DJ/VJ DVD player or DJ CD player or other line

level output component.

4 Signal ground terminal (SIGNAL GND)

Connect the ground wire from an analog turntable.

This is not a safety ground terminal.

5 CONTROL connector

Connect the Ø 3.5 mm mini phone plug of the control cable from

a DJ/VJ DVD player or DJ CD player.

When this is done, this mixer’s fader controls can be used to

perform start and back-cue functions on the connected DJ/VJ DVD

player or DJ CD player.

6 LINE input connectors

RCA type line level audio input connectors.

Use to connect a cassette deck or other line level output

component.

7 DVD input connectors

RCA type line level audio input connectors.

Use to connect a DJ/VJ DVD player or DJ CD player or other line

level output component.

8 Audio master output 1 connectors (MASTER OUT 1)

XLR type (male) balanced output.

• When using a cord with RCA-type plug, users are recommended

to connect the plug directly to the MASTER OUT 2 connectors

without using an XLR/RCA converter plug.

When a conversion plug is used, the signal GND may become

unstable, in rare cases resulting in the production of noise.

9 Audio master output attenuator selector (MASTER ATT.)

Attenuates the output level of the audio master 1 and audio master

2.

Attenuation level can be selected as 0 dB, –3 dB, or –6 dB.

10 Audio master output 2 connectors (

MASTER OUT 2

)

RCA-type unbalanced output.

11 Recording output connectors (REC OUT)

RCA type output connectors for recording.

12 BOOTH MONITOR output jacks (TRS)

Ø 6.3 mm phone-type booth monitor output jacks.

The sound level output at these connectors can be controlled by

the BOOTH MONITOR level dial, regardless of the setting of the

MASTER LEVEL dial. (Since the output is TRS, both balanced and

unbalanced outputs are supported.)

13 Microphone 2 input jack (MIC 2)

Connect microphones equipped with phone-type plug.

14 Sync signal output connector (SYNC OUT)

Outputs video sync signal.

When connecting a Pioneer DJ/VJ DVD player (sold separately),

the sync signal helps suppress any lag between video and audio

signals.

15 Digital input connector (DIGITAL IN)

RCA-type digital coaxial input connector. Connect to the digital

coaxial output connector from a DJ/VJ DVD player or DJ CD player.

• If the sampling frequency of the output signal changes, the

sound may be interrupted briefly.

16 Sampling frequency selector switch (fs 48 k/96 k)

Use to set the sampling frequency of the digital output to 96 kHz/

24-bit format or 48 kHz/24-bit format.

Turn power off before changing this switch position.

17 Digital output connector (DIGITAL OUT)

RCA type digital coaxial output connector.

Master audio digital output.

18 Power inlet (AC IN)

Use the furnished power cable to connect to a household AC

outlet.

19 Video input connectors (DVD, VIDEO, S-VIDEO)

Composite and S-VIDEO type video input connectors.

20 Video master output connectors

(MASTER: COMPONENT, COMPOSITE, S-VIDEO)

Component, composite, and S-VIDEO type video output

connectors.

21 Video monitor output connectors (MONITOR, S-VIDEO)

Composite and S-VIDEO type monitor video output connectors.

POWER

AC IN

ON

OFF

PHONO

SIGNAL GND

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

L

R

DVD/LINE LINE

MASTER OUT 1

1 GND 2 HOT

MASTER

ATT .

MASTER

COMPONENT COMPOSITE

YC

B CR

-3 dB

-6 dB 0 dB

3 COLD

DIGITAL

IN

DIGITAL OUT

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

S-VIDEO S-VIDEO

MONITOR

L

R

DVD

MASTER

OUT 2

BOOTH

MONITOR

(TRS)

L

R

LR

REC

OUT

R

4 3

LINE

SIGNAL GND

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

L

R

DVD PHONO

DIGITAL

IN

CONTROL

SYNC

OUT

DVD

USB

OUT

VIDEO

S-VIDEO

L

R

DVD/LINE

21

AUDIO OUT

VIDEO OUT

L

fs (Hz)

48 k 96 k

MIC2

MIDI

1

2 3 4 95 6 7 10 11

8 12

2 3 4 555 6 7 13

14 15 16 17 15 14

18 19 19 19 1921 232220

01_SVM-1000_B_En.book 6 ページ２００７年１１月２６日　月曜日　午後１時４４分

NAMES AND FUNCTIONS OF PARTS

7

En

English

22 MIDI OUT connector

DIN type output connector.

Use to connect to other MIDI component.

23 MIDI USB output connector

USB-B type output connector. Use to connect to a computer.

OPERATION PANEL

1 USB connector

Use to connect a USB memory or keyboard.

2 CH1/CH4 video input connectors (VIDEO EX)

Use to input video from an external source.

3 Microphone 1 input jack (MIC 1)

Connect microphone with XLR-type or phone-type plug.

4 Microphone 1 level control dial (MIC 1 LEVEL)

Use to adjust the volume of microphone 1. (Adjustable range –∞ to

0dB)

5 Microphone 2 level control dial (MIC 2 LEVEL)

Use to adjust the volume of microphone 2. (Adjustable range –∞ to

0dB)

6 Microphone equalizer high-range adjust dial (HI)

Use to adjust the treble (high-range) frequencies of microphones 1

and 2. (Adjustable range –12 dB to +12 dB)

7 Microphone equalizer low-range adjust dial (LOW)

Use to adjust the bass (low-range) frequencies of microphones 1

and 2. (Adjustable range –12 dB to +12 dB)

8 Microphone function selector switch (MIC)

OFF:

No microphone sound is output.

ON:

Microphone sounds are output, and the microphone function

indicator lights.

TALK OVER:

Microphone sounds are output, and the microphone function

indicator flashes.

When an audio signal of –15 dB or more (default setting) is input

to the microphone input, the talkover function operates to reduce

all output other than the mike audio by 20 dB (default setting).

Values can be changed in the hardware setup (P. 42)

• When not using the TALK OVER function, it is recommended to

set the switch to the [OFF] or [ON] position.

9 FADER START button/indicator (CH-1 to CH-4)

Enables the fader start/back cue function for the channel to which

a DJ/VJ DVD player or DJ CD player is connected. The button lights

when set to ON. When enabled, the operation differs depending on

the setting of the CROSS FADER ASSIGN switch.

•When the CROSS FADER ASSIGN switch is set to the [A] or [B]

position, FADER START button operation is linked to the

operation of the cross fader (and unlinked to channel fader).

•When the CROSS FADER ASSIGN switch is set to the [THRU]

position, FADER START button operation is linked to the

operation of the channel fader (and unlinked to cross fader).

MIC

FADER START

HEAD PHONES

VIDEO INPUT

USB

DVD

CH 1

VIDEO

EX

CH 4

MIC OFF ON

TALK

OVER

MIN

DVD/LINE PHONO

MAX

VIDEO

S-VIDEO

EX

VIDEO TRIM

MIC 1

MIC1

LEVEL

MIC2

LEVEL

HI

LOW

CH1

AUDIO INPUT

AUDIO TRIM

dB

OVER

10

7

4

2

1

0

–1

–2

–3

–5

–7

–10

–15

–24

+9

MID

+6-26

HI

+6-26

LOW

CUE

CROSS FADER

ASSIGN

PROFESSIONAL SOUND

&

VISION MIXER

AB

SVM-1000

+6-26

10

9

8

7

6

5

4

3

2

1

0

A THRU B

1

VIDEO INPUT

DVD

MIN

DVD LINE DIGITAL

MAX

VIDEO

S-VIDEO

VIDEO TRIM

AUDIO INPUT

AUDIO TRIM

dB

OVER

10

7

4

2

1

0

–1

–2

–3

–5

–7

–10

–15

–24

+9

MID

+6-26

HI

+6-26

LOW

CUE

CROSS FADER

ASSIGN

+6-26

10

9

8

7

6

5

4

3

2

1

0

A THRU B

2

VIDEO INPUT

DVD

MIN

DVD LINE DIGITAL

MAX

VIDEO

S-VIDEO

VIDEO TRIM

AUDIO INPUT

CH SELECT

AUDIO TRIM

dB

OVER

10

7

4

2

1

0

–1

–2

–3

–5

–7

–10

–15

–24

+9

MID

+6-26

HI

+6-26

LOW

CUE

CROSS FADER

ASSIGN

+6-26

10

9

8

7

6

5

4

3

2

1

0

CROSS FADER CURVE SD CARD

A THRU B

3

dB

OVER

10

7

4

2

1

0

–1

–2

–3

–5

–7

–10

–15

–24

VIDEO INPUT

DVD

MIN

LINE PHONO

MAX

VIDEO

S-VIDEO

VIDEO TRIM

AUDIO INPUT

AUDIO TRIM

dBLR

OVER

10

7

4

2

1

0

–1

–2

–3

–5

–7

–10

–15

–24

+9

BOOTH MONITOR

0

MID

+6-26

HI

+6-26

LOW

CUE

CROSS FADER

ASSIGN

+6-26

BALANCE

MASTER

RL

CUE

10

9

8

7

6

5

4

3

2

1

0

CH FADER CURVE

VIDEO

MASTER LEVEL

WHITEBLACK

MONO STEREO

A THRU B

4

EX

0

+12

-12

+12

-12

CH2

CH3

CH4

MONO SPLIT STEREO

MIXING

PHONES

MASTER

CUE

LEVEL

AUDIO MASTER LEVEL

0

TIME/

PARAMETER

LEVEL/

DEPTH

EFFECT

CUE

VIDEO FX

PATTERN/

TEXT BANK

MAXMIN

FADER

AV SYNC

VIDEO

SOLO MODE

JPEG

VIEWER

ON/OFF

SET UP

VIDEO EQ

MASTER

MONITOR

SET UP

UTILITY

EFFECT

ON/OFF

1

2

3

45

46

47

49

50

28

48

4

5

6

7

9

10

11

12

13

8

14 16 17 32

33

34

35

36

37

38

39

18

19 22

23 23

24 24

25 25

26

28

29

30

29

30

31

28

2727

26

23

24

25

27

28

26

23

24

25

28

26

18 18

20

18

21

15

40

41

42

43

44

29

30

29

30

51

01_SVM-1000_B_En.book 7 ページ２００７年１１月２６日　月曜日　午後１時４４分

NAMES AND FUNCTIONS OF PARTS

8

En

10 HEADPHONES output switch (MONO SPLIT/STEREO)

MONO SPLIT:

The source sound selected with the headphone CUE button is

output to the L channel, while the master sound is output to the R

channel (only when [MASTER] is selected with the headphone

CUE button).

STEREO:

The audio source selected with the headphone CUE button is

output in stereo.

11 HEADPHONES MIXING dial

When rotated clockwise (toward [MASTER]), the master output

audio is produced at the headphones (only when [MASTER] has

been selected with the headphone CUE button); when rotated

counterclockwise (toward [CUE]), the headphones output

becomes the mixture of the effect monitor and the channel

selected with the headphone CUE button.

12 HEADPHONES LEVEL adjust dial

Adjusts the output level of the headphones jack. (Adjustable

range: –∞ to 0 dB)

13 Headphones jack (PHONES)

14 Channel 1 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the

type of input connected.

15 Channel 2 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input

connected.

16 Channel 3 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input

connected.

17 Channel 4 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the

type of input connected.

18 VIDEO TRIM dial

Use to adjust the level of the video input signal for each channel.

• When rotated counterclockwise, the luminance level is reduced,

eventually producing a black screen.

• When rotated clockwise, the luminance level is raised,

eventually producing a white screen.

• At the center position, the luminance level is neutral (same level

as input).

19 Channel 1 AUDIO INPUT selector switch

DVD/LINE:

Use to select DVD/LINE input connectors (line level analog input).

PHONO:

Use to select

PHONO input connectors (PHONO level analog

input).

20 Channel 2 AUDIO INPUT selector switch

DVD:

Use to select DVD input connectors.

LINE:

Use to select LINE input connectors (line level analog input).

DIGITAL:

Use to select DIGITAL input connector.

21 Channel 3 AUDIO INPUT selector switch

DVD:

Use to select DVD input connectors.

LINE:

Use to select LINE input connectors (line level analog input).

DIGITAL:

Use to select DIGITAL input connector.

22 Channel 4 AUDIO INPUT selector switch

DVD/LINE:

Use to select DVD/LINE input connectors (line level analog input).

PHONO:

Use to select

PHONO input connectors (PHONO level analog

input).

23 AUDIO TRIM dial

Use to adjust the level of the audio input signal for each channel.

(Adjustable range: –∞ to +9 dB, mid-position is about 0 dB)

24 Channel equalizer high-range adjust dial (HI)

Use to adjust the treble (high-range) frequency sound for each

channel. Video parameters can also be assigned. See P. 34

regarding video parameters. (Adjustable range: –26 dB to +6 dB)

25 Channel equalizer mid-range adjust dial (MID)

Use to adjust the mid-range frequency sound for each channel.

Video parameters can also be assigned. See P. 34 regarding video

parameters. (Adjustable range: –26 dB to +6 dB)

26 Channel equalizer low-range adjust dial (LOW)

Use to adjust the bass (low-range) frequency sound for each

channel. Video parameters can also be assigned. See P. 34

regarding video parameters. (Adjustable range: –26 dB to +6 dB)

27 Channel level indicator

Displays the current level for each channel, with two-second peak

hold.

28 Headphone

CUE

buttons/indicators

These buttons are used to select from 1 to 4, MASTER, or

EFFECT CUE, to allow you to monitor the desired source through

headphones. If multiple buttons are pressed simultaneously, the

selected audio sources are mixed. Press the button once more to

cancel the selected source. Unselected buttons glow darkly, while

selected source buttons light brightly.

29 Channel fader lever

Use to adjust sound volumes and video level for each channel.

(Volume adjust range: –∞ to 0 dB) (Video adjust range: 0 % to

100 %)

Output is in accordance with the channel fader curve selected with

the CH FADER CURVE switch.

When FADER AV SYNC function is OFF, only sound volume can be

adjusted.

30 CROSS FADER ASSIGN switch

This switch assigns each channel’s output to either right or left

side of the cross fader (if multiple channels are assigned to the

same side, the result will be the combined sum of the channels).

A:

The selected channel is assigned to the cross fader’s [A] (left) side.

THRU:

The channel fader’s output is sent as is to the master output,

without being passed through the cross fader.

B:

The selected channel is assigned to the cross fader’s [B] (right)

side.

31 CROSS FADER CURVE switch

This switch allows the user to select from three types of cross fader

curve response.

Sound volume changes as follows:

• At the left setting, the curve produces a rapid signal rise. (As

soon as the cross fader lever leaves the [A] side, the [B] channel

sound is produced.)

• At the right setting, the curve operates to produce an even,

neutral rise throughout the cross fader’s movement.

• At the middle setting, an intermediate curve is produced,

midway between the two curves noted above.

The video level is as noted above only when the video cross fader’s

video mix effect is set to [FADE].

32 Video master output level dial (VIDEO MASTER LEVEL)

Adjusts the video master output luminance level.

33 Master output MONO/STEREO selector switch

When set to the [MONO] position, audio master output is

produced in L+R monaural.

34 Audio master output level dial (AUDIO MASTER LEVEL)

Use to adjust the master output level. (Adjustable range: –∞ to

0dB)

The master output is the sum combination of the sound from

channels set to [THRU] with the CROSS FADER ASSIGN switch;

01_SVM-1000_B_En.book 8 ページ２００７年１１月２６日　月曜日　午後１時４４分

NAMES AND FUNCTIONS OF PARTS

9

En

English

the signal passed through the cross fader; and the signals from

microphone 1 and microphone 2.

35 Master level indicator (MASTER L, R)

These segment indicators display the audio output level from L and

R channels. The indicators have a two-second peak hold.

36 Master balance dial (BALANCE)

Use to adjust the L/R channel balance for audio master output,

booth monitor output, recording output, and digital output.

37 BOOTH MONITOR level control dial

This dial is used to adjust the booth monitor output volume.

The volume can be adjusted independently of the master output

level. (Adjustable range: –∞ to 0 dB)

38 Channel fader curve switch (CH FADER CURVE)

This switch allows the user to select from three types of channel

fader curve response.

The sound volume and video level changes as follows:

This setting is applied equally to channels 1 to 4.

• At the left setting, the curve operates to produce a rapid rise as

the channel fader approaches its distant position.

• At the right setting, the curve operates to produce an even,

neutral rise throughout the channel fader’s movement.

• At the middle setting, an intermediate curve is produced,

midway between the two curves noted above.

39 SD CARD slot

Insert an SD card.

40 UTILITY button (MASTER MONITOR, SET UP)

Switches between display / no display of the master monitor on the

LCD. When the master monitor is set to display, the indicator

lights. When the button is held depressed, the indicator changes

to flashing, and the LCD screen changes to show the utility setup

menu.

41 VIDEO EQ button (ON/OFF, SET UP)

Switches the video equalizer ON/OFF. The indicator lights when

the video equalizer is ON. When the button is held depressed, the

indicator flashes, and the LCD display changes to show the

equalizer setup menu.

42 JPEG VIEWER button

Use to set the JPEG viewer mode. The indicator lights when in the

JPEG viewer mode.

43 VIDEO SOLO MODE button

Use to switch the video solo mode ON/OFF. When the video solo

mode is ON, the indicator will flash.

44 Fader AV synchro button (FADER AV SYNC)

This button determines whether sound and video are controlled

together, or independently. When set to ON, the indicator lights,

and the channel fader and cross fader operations change both

sound and video simultaneously. When set to OFF, the channel

fader and cross fader levers control sound only, while video is

controlled by the touch panel.

45 Effect channel selector dial (CH SELECT)

Use to select the channel to which effects are applied. When [MIC]

is selected, effects are applied to both microphone 1 and

microphone 2.

46 VIDEO FX PATTERN/TEXT BANK dial

Use to select video effects, video effect patterns and text banks.

47 Effect parameter 1 dial (TIME/PARAMETER)

Adjusts parameter for selected effect.

• If this dial is rotated while depressing the TAP button, direct

BPM can be set manually.

48 Effect parameter 2 dial (LEVEL/DEPTH)

Adjusts quantitative parameters for selected effect.

49

TAP

button

The BPM is calculated from the intervals at which the TAP button

is struck.

50 Effect button/indicator (EFFECT ON/OFF)

Turns selected effect ON/OFF.

When power is turned ON, the button lights (defaults to effect

OFF). When effects are enabled (ON), the button flashes.

51 Cross fader lever (A/B)

This adjusts sound and video levels assigned to sides [A] and [B]

in accordance with the CROSS FADER ASSIGN switches. When

FADER AV SYNC is OFF, the control adjusts the sound only.

01_SVM-1000_B_En.book 9 ページ２００７年１１月２６日　月曜日　午後１時４４分

CONNECTIONS

10

En

CONNECTIONS

Always turn off the power switch and disconnect the power plug from its outlet when making or changing connections.

CONNECTING INPUTS

Pioneer DJ/VJ DVD players or DJ CD players

Audio cable connection

A DJ/VJ DVD or DJ CD player’s audio output connectors can be

connected to this unit’s DVD, DVD/LINE or LINE connectors.

When using the player’s digital output, connect to this unit’s

channel 2 or channel 3 DIGITAL IN connector. Use the AUDIO

INPUT selector switch (on top panel of this unit) to select the

proper connector.

Likewise, the control cord should be connected to the CONTROL

connector of the selected channel.

Video cable connection

A DJ/VJ DVD player’s video output connectors can be connected

to this unit’s DVD, VIDEO, or S-VIDEO connectors. When this is

done, use the VIDEO INPUT selector switch (on top panel of this

unit) to select the proper connector.

Likewise, connect a commercially available sync signal cable to

the SYNC OUT connector of the selected channel.

Connecting an analog turntable

Connect the audio output cables from an analog turntable to this

unit’s Channel 1 or 4 PHONO input connectors, then set the

connected channel’s AUDIO INPUT switch (on the upper panel of

this unit) to [PHONO]. This unit’s PHONO input supports MM

cartridges.

Connect the ground wire from an analog turntable to the SIGNAL

GND terminal of the SVM-1000.

•Note that no PHONO input connector is provided for channel 2

and 3.

Connecting other line level output devices

To use a cassette deck or ordinary CD player, connect its audio

output connectors to one of the SVM-1000's LINE input connectors

(channel 1 to 4).

POWER

AC IN

ON

OFF

DVD

VIDEO

S-VIDEO

MASTER OUT 1

1 GND 2 HOT

MASTER

ATT.

MASTER

COMPONENT COMPOSITE

YC

B CR

-3 dB

-6 dB 0 dB

3 COLD

DIGITAL OUT

DVD

VIDEO

S-VIDEO

S-VIDEO S-VIDEO

MONITOR

L

MASTER

OUT 2

BOOTH

MONITOR

(TRS)

L

R

LR

REC

OUT

R

DVD

VIDEO

S-VIDEO

DVD

USB

OUT

VIDEO

S-VIDEO

AUDIO OUT

VIDEO OUT

L

fs (Hz)

48 k 96 k

MIC2

MIDI

PHONO

SIGNAL GND

L

R

DVD/LINE

4 3

CONTROL

SYNC

OUT

LINE

DIGITAL

IN

CONTROL

SYNC

OUT

R

DVD LINE

SIGNAL GND

CONTROL

SYNC

OUT

L

R

DVD PHONO

DIGITAL

IN

CONTROL

SYNC

OUT

L

R

DVD/LINE

21

L R L R L RL R L R LR

Analog turntable Analog turntableDJ/VJ DVD player or

DJ CD player

DJ/VJ DVD player or

DJ CD player

Cassette deck, etc.

CD player, etc.

01_SVM-1000_B_En.book 10 ページ２００７年１１月２６日　月曜日　午後１時４４分

CONNECTIONS

11

En

English

CONNECTING OUTPUTS

Audio master output

This unit is furnished with balanced output MASTER OUT 1

(supporting XLR plugs), and unbalanced output MASTER OUT 2

(supporting RCA plugs).

Using the MASTER ATT. switch, adjust the output level to match

the input sensitivity of the power amplifier used.

If the operating panel’s MONO/STEREO switch is set to [MONO],

the master output will be a monaural combination of L+R

channels.

Booth monitor output

TRS output for ø 6.3 mm phone plug. The sound volume for this

output is controlled by the BOOTH MONITOR level dial,

independently of the master output level setting.

Recording output

These are output connectors for recording, supporting RCA plugs.

Digital output

This is a coaxial digital output connector, supporting RCA plugs.

The sampling frequency can be set to 96 kHz/24-bit format or

48 kHz/24-bit format to match the connected device.

Turn power off before changing this switch position.

Video master output

Supports component, composite (RCA, BNC connector) and S-

VIDEO outputs.

Monitor output

Supports composite and S-VIDEO outputs.

POWER

AC IN

ON

OFF

PHONO

SIGNAL GND

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

L

R

DVD/LINE LINE

DIGITAL

IN

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

L

R

DVD

4 3

LINE

SIGNAL GND

CONTROL

SYNC

OUT

DVD

VIDEO

S-VIDEO

L

R

DVD PHONO

DIGITAL

IN

CONTROL

SYNC

OUT

DVD

USB

OUT

VIDEO

S-VIDEO

L

R

DVD/LINE

21

MIC2

MIDI

MASTER OUT 1

1 GND 2 HOT

MASTER

ATT.

MASTER

COMPONENT COMPOSITE

YC

B CR

-3 dB

-6 dB 0 dB

3 COLD

DIGITAL OUT

S-VIDEO S-VIDEO

MONITOR

MASTER

OUT 2

BOOTH

MONITOR

(TRS)

L

R

LR

REC

OUT

R

AUDIO OUT

VIDEO OUT

L

fs (Hz)

48 k 96 k

L R

LR

Power amplifier

(RCA plug input

connectors)

Cassette deck

(analog input

recording device)

Sampling

frequency

selector switch

Digital input AV amplifier

(digital input

recording device)

Power amplifier

(XLR plug input connectors)

MASTER ATT. switch

Power amplifier

(for booth monitor)

Plasma display Display

(for monitor)

01_SVM-1000_B_En.book 11 ページ２００７年１１月２６日　月曜日　午後１時４４分

CONNECTIONS

12

En

CONNECTING MICROPHONE AND HEADPHONES

Microphone

A microphone with XLR-type or Ø 6.3 mm phone-type plug can be

connected to the MIC 1 connector on the operation panel (upper) .

The MIC 2 jack on the connection panel (rear) can be used to

connect a microphone with Ø 6.3 mm phone-type plug.

• When using a microphone, set the operating panel’s MIC switch

to [ON] or [TALK OVER], and adjust the LEVEL dial as

necessary.

When not using a microphone, it is recommended to set the

MIC switch to [OFF] and rotate the LEVEL dial fully

counterclockwise to the [–∞] side.

Headphones

The PHONES jack on the operating panel (upper) can be used to

connect headphones with a Ø 6.3 mm stereo phone plug.

External video connector

A camera, DVD player or other video output device can be

connected to the CH 1/CH 4 video input connectors on the

operating panel (top).

CONNECTING THE POWER CORD

Connect the power cord last.

When all connections are completed, connect one end of the

furnished power cord to the AC inlet on the rear panel, and the

plug on the other end to a household AC outlet, or the auxiliary

power outlet on an amplifier. Use only the furnished power cord for

this connection.

USB

OUT

MIC2

MIDI

MIC

USB

CH 1

VIDEO

EX

CH 4

MIC 1

Microphone 1

Microphone 2

HEAD PHONES

CROSS FADER

ASSIGN

PROFESSIONAL S

O

SVM

-

9

8

7

6

5

4

3

2

1

0

A THRU B

0

MONO SPLIT STEREO

MIXING

PHONES

MASTER

CUE

LEVEL

Headphones

MIC

USB

CH 1

VIDEO

EX

CH 4

MIC 1

Video cameras and

devices

01_SVM-1000_B_En.book 12 ページ２００７年１１月２６日　月曜日　午後１時４４分

BASIC OPERATIONS

13

En

English

BASIC OPERATIONS

1 Set rear panel POWER switch to [ON].

2 Set the AUDIO INPUT switch for the desired channel to match

the type of connected component.

• When using the DVD input, set to [DVD].

• When using LINE input, set to [LINE].

• When using DVD/LINE input, set to [DVD/LINE].

• When using DIGITAL input, set to [DIGITAL].

• When using PHONO input, set to [PHONO].

3 Use the VIDEO INPUT switch for the selected channel to

choose the video input.

4 Use the AUDIO TRIM dial to adjust the input level for each

channel.

5 Use the VIDEO TRIM dial to adjust the input level for each

channel.

6 Use the channel equalizer dials (HI, MID, LOW) to adjust the

tone.

7 Use the channel fader lever to adjust the sound volume of

the selected channel.

8 To use the cross fader on the selected channel, set the CROSS

FADER ASSIGN switch to either cross fader channel A or

channel B, and operate the cross fader lever (A/B).

• When not using the cross fader, set the

CROSS FADER

ASSIGN

switch to [THRU].

9 Use the AUDIO MASTER LEVEL dial to adjust the overall

sound volume.

10 Use the VIDEO MASTER LEVEL dial to adjust the overall

luminance level.

11 Use the BALANCE dial to adjust the sound balance between

right and left.

HI

10

9

8

7

6

5

4

3

2

1

0

10

9

8

7

6

5

4

3

2

1

0

POWER

AUDIO TRIM

VIDEO TRIM

VIDEO MASTER LEVEL

AUDIO MASTER LEVEL

BALANCE

HI, MID,

LOW

HI, MID,

LOW

CROSS FADER

ASSIGN

AUDIO

INPUT

VIDEO

INPUT

Channel fader

lever

Cross fader lever

(A/B)

01_SVM-1000_B_En.book 13 ページ２００７年１１月２６日　月曜日　午後１時４４分

BASIC OPERATIONS

14

En

Selecting Stereo or Monaural

When the MONO/STEREO switch is set to [MONO], the audio

master output becomes a monaural combination of L+R

channels.

Microphone Input

1 To use a microphone, set the MIC switch to [ON] or [TALK

OVER].

When set to [

TALK OVER

], any time a sound of –15 dB (default

setting) or more is input, all sound sources other than the

microphone are attenuated by 20 dB (default setting). These

default values can be changed in the hardware setup (P. 42).

2 Use the MIC 1 LEVEL dial to adjust the sound volume of

MIC 1, and use the MIC 2 LEVEL dial to adjust the sound

volume of MIC 2.

3 Use the microphone equalizer dials (HI, LOW) to adjust the

tone of the microphone sound.

• The microphone equalizer function operates simultaneously

on microphone 1 and 2.

Booth Monitor Output

1 Use the BOOTH MONITOR level dial to adjust the sound

volume.

•The

BOOTH MONITOR

level dial can be used to adjust the

sound volume independently of the AUDIO MASTER LEVEL

dial.

• Use the hardware setup (P. 42) to set whether or not the

microphone sound is to be output to the booth monitor.

Headphones Output

1 Use the headphone CUE buttons (channels 1 to 4, MASTER,

EFFECT CUE) to select the source.

•The selected

CUE

button lights brightly.

2 Set the HEADPHONES (MONO SPLIT/STEREO) switch.

• When set to the [MONO SPLIT] position, the sound selected

with the headphone

CUE

button is output to the left channel,

and the master sound is output to the right channel (only

when MASTER CUE button is set to ON).

• When set to the [STEREO] position, the sound selected with

the headphone

CUE

button is output in stereo.

3 When [MONO SPLIT] is selected, use the HEADPHONES

MIXING dial to adjust the balance of sound between the left

channel (sound selected with the headphone CUE button),

and the right channel (master sound).

• When the

HEADPHONES MIXING

dial is rotated clockwise

(toward [MASTER]), the master output (only when the

MASTER CUE button is ON) increases; when rotated

counterclockwise (toward [

CUE

]), the sound selected with

the headphone

CUE

button increases.

4 Use the HEADPHONES LEVEL dial to adjust the headphones’

sound volume.

• Rotate the HEADPHONES LEVEL dial to adjust the sound

level.

• When the Effect mode select button (P. 17) is set to [V]

mode, effect sounds will not be output even if the

EFFECT CUE button is pressed.

FADER CURVE SELECTION

The response of sound volume change to the fader control can be

set in three types.

Use the CH FADER CURVE switch to select the desired channel

fader response curve.

The sound volume and video level changes as follows:

• At the left setting, the curve operates to produce a rapid rise as

the channel fader approaches its distant position.

• At the right setting, the curve operates to produce an even,

neutral rise throughout the channel fader’s movement.

• At the middle setting, an intermediate curve is produced,

midway between the two curves noted above.

• This setting applies equally to channels 1 to 4.

Use the CROSS FADER CURVE switch to select the cross fader

curve response.

Sound volume changes as follows:

• At the left setting, the curve produces a rapid signal rise. (As

soon as the cross fader lever leaves the [A] side, the [B] channel

sound is produced.)

• At the right setting, the curve operates to produce an even,

neutral rise throughout the cross fader’s movement.

• At the middle setting, an intermediate curve is produced,

midway between the two curves noted above.

• This setting produces equal curve effects for both sides A and B.

The video level is as noted above only when the video cross fader’s

video mix effect is set to [FADE].

HI

10

9

8

7

6

5

4

3

2

1

0

10

9

8

7

6

5

4

3

2

1

0

MONO/STEREO

CUE

LEVEL

BOOTH MONITOR

CH FADER CURVE

CROSS FADER CURVE

MIC

HI, LOW

MIC1 LEVEL

MIC2 LEVEL

MIXING

MONO SPLIT/STEREO

01_SVM-1000_B_En.book 14 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE VIDEO CONTROL FUNCTIONS

15

En

English

USING THE VIDEO CONTROL FUNCTIONS

Touch the LCD screen to control video functions. Supports video cross fader functions and video channel switch functions.

OPERATING THE VIDEO CROSS FADER

The video cross fader is used to manipulate video images.

1 Using the CROSS FADER ASSIGN switch, choose either

Channel A or Channel B of the cross fader

• When assigned to Channel [A], the border of the channel

preview monitor appears blue; when assigned to Channel

[B], the border of the channel preview monitor appears red.

When assigned to [THRU], the border appears gray.

• When JPEG is assigned, the [JPEG] indicator will appear at

the upper left of the channel monitor.

2 Touch a video mix effect button to choose a video mix effect.

• The selected button will appear white, and the icon will move

as an animation.

• For each effect refer to P. 16.

3 Operate the video cross fader.

• The video will change as video mix effects are being applied.

• When FADER AV SYNC is set to ON, the video cross fader

section’s [AV SYNC] indicator will appear, and the video

cross fader will operate in synchronization with the cross

fader. Touching the video cross fader allows you to

manipulate the video while you are touching it. Release to

return to the same position as the cross fader.

• When FADER AV SYNC is set to OFF, the video cross fader

section’s [AV SYNC] indicator goes out, and the sound and

video are controlled independently. The sound is controlled

by the cross fader, and the video by the video cross fader.

•When the [TRANS] button is touched, the video

corresponding to the touched side will be output regardless

of the position of the video cross fader.

• When all cross fader assigns are set to [THRU], the video

cross fader and [TRANS] button will appear gray, and if

assigned, the buttons will function as video cross fader,

[TRANS] buttons, with [A] side appearing blue and [B] side

appearing red.

OPERATING THE VIDEO CHANNEL SWITCH

The channel monitor functions as a switch to turn that channel’s

video ON/OFF.

1 Touch the channel monitor.

• The touched video output will alternate ON/OFF.

• When FADER AV SYNC is set to ON, the video level will be

displayed in red. If the video level is not dispayed (channel

fader is [0]), touch the channel to output that channel’s

video. Or alternately, when the video level is displayed,

touching the channel monitor will cause that channel’s

video to turn off during the duration the screen is touched.

• When FADER AV SYNC is set to OFF, the video level is

displayed in green. The channel monitor can be touched to

alternate that video output ON/OFF.

1 Channel

monitor

Monitors videos from each input channel

(1 through 4).

Touch the channel monitor to output the

video of each channel.

2 Video level

Indicates video output level.

Appears red when FADER AV SYNC is

ON, and appears green when FADER AV

SYNC is OFF.

3 Video mix effect

button

Use to select type of video change when

video cross fader is operated.

4 Video cross

fader

Video cross fader.

5 Transfomer

button [TRANS]

Outputs video of touched side, regardless

of position of video cross fader.

HI

10

9

8

7

6

5

4

3

2

1

0

10

9

8

7

6

5

4

3

2

1

0

VIDEO SOLO MODE

CROSS FADER

ASSIGN

Cross fader lever (A/B)

FADER AV

SYNC

3

5 54

1

2

01_SVM-1000_B_En.book 15 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE VIDEO CONTROL FUNCTIONS

16

En

OPERATING IN THE VIDEO SOLO MODE

Setting video solo mode to ON allows instantaneous switching to

the desired channel’s video.

By combining with the FADER AV SYNC button ON/OFF, a variety

of operations is possible.

Whenever the power is first turned ON, the video solo mode is set

to OFF by default.

When the video solo mode is ON, the VIDEO SOLO MODE button

will flash.

When FADER AV SYNC is ON

• When the channel monitor is touched, output instantaneously

switches to the video of the touched channel.

• When the channel fader begins rising from the [0] position,

output instantaneously switches to that channel’s video.

When

FADER

AV SYNC is OFF

• When the channel monitor is touched, output instantaneously

switches to the video of the touched channel.

Upon changing the FADER AV SYNC from ON to OFF, the original

channel fader position will be maintained until the channel

monitor is touched again.

Operation of the video cross fader and [TRANS] button are not

supported in the video solo mode.

VIDEO MIX EFFECTS CHART

Video mix effects

Video cross fader

No Name Description of the effect

1 FADE Switches video while mixing.

2 WIPE Switches video while wiping away.

3 SWITCH Switches instantaneously (without mixing).

4 CHROMA-B Switches from the blue component of video on cross fader side [A] to the

video on side [B].

5 CHROMA-G Switches from the green component of video on cross fader side [A] to the

video on side [B].

6 LUMINANCE Switches from the dark portion of video on cross fader side [A] to the video

on side [B].

01_SVM-1000_B_En.book 16 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE EFFECT FUNCTION

17

En

English

USING THE EFFECT FUNCTION

This function applies effects to the selected channel’s sound and video. Effects include BEAT effects, which are applied in linkage to the

track’s BPM; TOUCH effects, which control effects by directly touching the screen; and TEXT effects, which display onscreen characters

with effects added in rhythm to the track. The UTILITY (MASTER MONITOR) button can be pressed to display the master monitor’s image

on the LCD screen.

USING BEAT EFFECTS

BEAT effects can be instantaneously set in-sync with the BPM

(Beat Per Minute) of the track, enabling you to apply various effects

to the rhythm even during live performances.

When master monitor is off

When master monitor is on

HI

10

9

8

7

6

5

4

3

2

1

0

10

9

8

7

6

5

4

3

2

1

0

USB

UTILITY

(MASTER MONITOR) CH SELECT

EFFECT

ON/OFF

TAP

VIDEO FX

PATTERN

1

5

6 7

11

8

10

9

4

2

1 Effect category

buttons

Selects the category of effects you wish to

apply. Select from [BEAT] (red), [TOUCH]

(blue), and [TEXT] (green).

2 Effect select

buttons

Select and touch the desired effect button

from the 12 BEAT effects.

3 MASTER

monitor

When master monitor is on, displays

master output.

4 Channel select

display

Rotate the CH SELECT dial to select the

channel to which you wish to apply the

effect.

5 Effect mode

select buttons

A: Touch to apply the effect to audio only.

AV: Touch to apply the effect to both

audio and video.

V: Touch to apply the effect to video only.

6 Video EFFECT

monitor

Monitors effect results.

7 Video effect

pattern display

Rotate the VIDEO FX PATTERN/TEXT

BANK dial to select the video effect

pattern. When BEAT effect is enabled, you

can choose from

[ORIGINAL]/[INVERSE]/[EDGE]/[HUE].

8[BPM

AUTO/TAP]

button

Touch to switch the measurement

method of the BPM between AUTO and

TAP.

9 BPM/parameter

display

Displays the measured BPM and effect

parameters.

10 Beat button

Touch to select the multiplication factor

of the beat calculated from the BPM for

synchronization of effects.

11 [VISUALIZER]

button

Allows use of images produced internally

by the unit.

1

3

5

6

4

7

2

11

8

9

10

01_SVM-1000_B_En.book 17 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE EFFECT FUNCTION

18

En

1 Touch the [BPM AUTO/TAP] button to select the BPM (=Beat

Per Minute) measurement mode.

AUTO: The BPM is automatically measured from the input

music signal.

TAP: Tap the TAP button with your finger to manually input the

BPM.

• Whenever power is first turned ON, [AUTO] is selected by

default.

•The selected mode ([AUTO]/[TAP]) will appear in the

display.

• When a BPM cannot be measured automatically, the BPM

display in the display will flash.

• The measurement range of AUTO mode is BPM=70 to 180.

Depending on the track, the BPM may not be accurately

measured. In these cases, use TAP mode to manually enter

the BPM.

[Manually entering the BPM using the TAP button]

When the TAP button is tapped to the beat (a quarter note) more

than twice, the average length will be set as the BPM.

•Pressing the TAP button during [AUTO] mode will switch the

BPM measurement mode to [TAP], and the length between the

taps will be measured.

• When a BPM is set using the TAP button, the multiplication

factor will become [1/1] or [4/1] (depending on the effect), and

the effect time will be set to either the length of 1 beat (a quarter

note) or 4 beats.

• Rotate the TIME/PARAMETER dial while pressing the TAP

button to set the BPM directly.

•Touch the [BPM AUTO/TAP] button to return to [AUTO] mode.

2 Touch the effect category button [BEAT].

•The [BEAT] button will light brightly, and the icon will move

as an animation.

• The BEAT effect screen will be displayed.

• Whenever power is first turned ON, the [BEAT] effect is

selected by default.

3 Use the effect select buttons to select an effect type.

• The selected button will appear white, and the icon will move

as an animation.

• For a description of each effect, refer to P. 23.

4 Use the CH SELECT dial to select the channel to which you

wish to apply the effect.

• The selected effect channel display will appear white.

•If [MIC] is selected, the audio effect will be applied to both

MIC 1 and MIC 2. There will be no effect on the video.

• When turning the power ON, [MASTER] will be selected.

5 Touch the effect mode select button to select the effect

mode.

• The selected button will appear white, and the icon will move

as an animation.

A: The effect will be applied to the audio only.

AV: The effect will be applied to both the audio and video.

V: The effect will be applied to the video only.

• When turning the power ON, [AV] will be selected.

6 Touch the beat button to choose the multiplication factor of

the beat for synchronization of the effect.

• Select the beat number calculated from the BPM.

• The selected beat button will be highlighted.

• An effect time that corresponds to the multiplication factor

of the beat will be automatically set.

[Example] When BPM=120

1/1 = 500 ms

1/2 = 250 ms

2/1 = 1000 ms

7 Set the EFFECT ON/OFF button to ON to apply the effect.

• Each time the button is pressed it will switch between ON

and OFF (whenever power is first turned ON, the setting

defaults to OFF).

• When effect is ON, the button flashes.

Video effect pattern

Rotate the VIDEO FX PATTERN/TEXT BANK dial to select a video

effect pattern for the selected video effect.

For descriptions on the video effect pattern change caused by

rotating the VIDEO FX PATTERN/TEXT BANK dial, refer to P. 24.

Parameter 1

Rotate the TIME/PARAMETER dial to adjust temporal parameters

of the selected effect.

For descriptions on the changes in parameter 1 caused by turning

the TIME/PARAMETER dial, refer to P. 23.

Parameter 2

Rotate the LEVEL/DEPTH dial to adjust quantitative parameters of

the selected effect.

For descriptions on the changes in parameter 2 caused by rotating

the LEVEL/DEPTH dial, refer to P. 23.

Using the visualizer

This function allows the use of images produced internally by the

unit.

1 Set [VISUALIZER] button to [ON].

The video effect monitor displays the image.

2 Use the effect select buttons to choose a desired image.

3 Use the CH SELECT dial to select the desired channel.

• The image will move automatically in rhythm to the music’s

beat.

• In the event no input image is present, the visualizer’s image

can be used.

01_SVM-1000_B_En.book 18 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE EFFECT FUNCTION

19

En

English

USING TOUCH EFFECTS

With TOUCH effects, many effects can be created by touching the

video EFFECT performance monitor.

When master monitor is off

When master monitor is on

1 Touch the effect category button [TOUCH].

•The [TOUCH] button will light brightly, and the icon will

move as an animation.

• The TOUCH effect screen will be displayed.

2 Select an effect from the effect select buttons.

• The selected button will appear white, and the icon will move

as an animation.

• For a description of each effect, refer to P. 25.

3 Use the CH SELECT dial to select the channel to which you

wish to apply the effect.

• The selected effect channel display will appear white.

•If [MIC] is selected, the audio effect will be applied to both

MIC 1 and MIC 2. There will be no effect on the video.

4 Touch the effect mode select button to select the effect

mode.

• The selected button will appear white, and the icon will move

as an animation.

A: The effect will be applied to the audio only.

AV: The effect will be applied to both the audio and video.

V: The effect will be applied to the video only.

• When turning the power ON, [AV] will be selected.

5 Set the EFFECT ON/OFF button to ON to apply the effect.

• Each time the button is pressed it will switch between ON

and OFF (whenever power is first turned ON, the setting

defaults to OFF).

• When effect is ON, the button flashes.

6 Touch the video effect performance monitor to change the

effects.

•When [HOLD] button is set to [ON], effects are recorded

from the time the screen is touched until the finger is

removed (max. 8 sec.), then output repeatedly.

•Each time the [HOLD] button is touched it will switch

between [ON] and [OFF].

• Whenever power is first turned ON, the setting defaults to

[OFF].

Pattern

Rotate the VIDEO FX PATTERN/TEXT BANK dial to select a video

effect pattern of the selected video effect.

For descriptions of the video pattern changes caused by rotating

the VIDEO FX PATTERN/TEXT BANK dial, refer to P. 25.

Parameter 1

Rotate the TIME/PARAMETER dial to adjust the parameters for

the selected effect.

For descriptions on the changes in parameter 1 caused by rotating

the TIME/PARAMETER dial, refer to P. 25.

Parameter 2

Rotate the LEVEL/DEPTH dial to adjust the quantitative

parameters for the selected effect.

For descriptions on the changes in parameter 2 caused by rotating

the LEVEL/DEPTH dial, refer to P. 25.

Using the Visualizer

This function allows the use of images produced internally by the

unit.

1 Set [VISUALIZER] button to [ON].

The video effect performance monitor displays the image.

1 Effect select

buttons

Select and touch the desired effect button

from the 12 TOUCH effects.

2 Effect mode

select buttons

A: Touch to apply the effect to audio only.

AV: Touch to apply the effect to both

audio and video.

V: Touch to apply the effect to video only.

3 Video EFFECT

performance

monitor

Touch here to apply effects to the video

image.

4 Video effect

pattern display

Rotate the VIDEO FX PATTERN/TEXT

BANK dial to select the video effect

pattern. The pattern will differ depending

on the effect type.

5 Parameter

display

Displays the TOUCH effect parameter.

The parameter will differ depending on

the effect type

2

7

4

5

6

3

1

4

5

7

1

6

2 23

6 [HOLD] button

When [HOLD] button is set to [ON],

effects are recorded from the time the

screen is touched until the finger is

removed.

7 [VISUALIZER]

button

Internally creates a video image to which

TOUCH effects can be applied.

01_SVM-1000_B_En.book 19 ページ２００７年１１月２６日　月曜日　午後１時４４分

USING THE EFFECT FUNCTION

20

En

2 Use the effect select buttons to choose a desired image.

3 Touch the image to apply changes.

4 Use the CH SELECT dial to select the desired channel.

• In the event no input image is present, the visualizer’s image

can be used.

USING TEXT EFFECTS

TEXT effects can be instantaneously set in-sync with the BPM

(Beat Per Minute) of the track, enabling you to apply various TEXT

effects to the rhythm.

When master monitor is off

When master monitor is on

1 Touch the [BPM AUTO/TAP] button to select the BPM (=Beat

Per Minute) measurement mode.

AUTO: The BPM is automatically measured from the input

music signal.

TAP: Tap the TAP button with your finger to manually input the

BPM.

• Whenever power is first turned ON, [AUTO] is selected by

default.

•The selected mode ([AUTO]/[TAP]) will appear in the

display.

• When a BPM cannot be measured automatically, the BPM

display in the display will flash.

• The measurement range of AUTO mode is BPM=70 to 180.

Depending on the track, the BPM may not be accurately

measured. In these cases, use TAP mode to manually input

the BPM.

2 Touch the effect category button [TEXT].

•The [TEXT] button will light brightly, and the icon will move

as an animation.

• The TEXT effect screen will be displayed.

3 Select a text effect using the effect select buttons.

• The selected button will appear white, and the icon will move

as an animation.

• For a description of each effect, refer to P. 30.

4 Choose a text from TEXT BANK.

• Rotate the VIDEO FX PATTERN/TEXT BANK dial to select

TEXT BANK and touch the [TEXT BANK] button to select the

text.

• The selected button will appear white.

5 Use the CH SELECT dial to select the channel to which you

wish to apply the effect.

• The selected effect channel display will be highlighted.

• TEXT effects are not supported when [MIC] is selected.

Effects are applied to audio only.

6 Touch the effect mode select buttons to choose the effect

mode.

• The selected button will be highlighted and an animation

will appear.

A: An effect will be applied to the audio only.

AV: An effect will be applied to both the audio and video.

V: An effect will be applied to the video only.

• When turning the power ON, [AV] will be selected.

1 Effect select

buttons

Select and touch the desired effect button

from the 6 TEXT effects.

2 [TEXT BANK]

buttons

Touch the text button of your choice from

the 6 texts.

3 TEXT BANK

display

Rotate the VIDEO FX PATTERN/TEXT

BANK dial to select a TEXT BANK from

the 10 available.

4 Effect mode

select button

A: Touch to apply the effect to audio only.

AV: Touch to apply the effect to both

audio and video.

V: Touch to apply the effect to video only.

1

2

5

6

3

7

8

9

4

3

1

2

4

7

5

8

9

6

3

5 Video EFFECT

monitor

Monitors the TEXT effects.

6 [TEXT EDIT]

button

Touch to edit the text of the selected

[TEXT BANK] button.

7[BPM

AUTO/TAP]

button

Touch to switch the measurement

method of the BPM between AUTO and

TAP. Pressing the TAP button will also

switch this to TAP.

8 Parameter

display

Displays the measured BPM and effect

parameters.

9Beat

button/beat

display

Touch to select the multiplication factor

of the beat calculated from the BPM for

synchronization of effects.

01_SVM-1000_B_En.book 20 ページ２００７年１１月２６日　月曜日　午後１時４４分

La pagina sta caricando ...

Pioneer Music Mixer SVM-1000 Manuale utente

Questo manuale è adatto anche per

Pioneer Music Mixer SVM-1000 Manuale utente

in altre lingue

Documenti correlati

Altri documenti