Ninebot Air T15 Manuale utente

Producent zastrzega sobie prawo do wprowadzania zmian w produkcie, aktualizacji

oprogramowania i aktualizacji tej instrukcji obsługi w dowolnym momencie. Odwiedź stronę

www.segway.com lub sprawdź aplikację, aby pobrać najnowsze materiały użytkownika. Musisz

zainstalować aplikację, aktywować swojego KickScootera i uzyskać najnowsze aktualizacje i

zasady bezpieczeństwa.

www.segway.com K023P0283-A0

Ninebot KickScooter

User Manual

Air T15

Thanks for choosing the Ninebot KickScooter!

Thanks for choosing the Ninebot KickScooter (hereinafter referred to as KickScooter)!

Your KickScooter is a recreational transportation device with mobile connectivity, allowing you to connect

with other riders. Enjoy your ride and connect with riders worldwide!

2 Packing List

3 Diagram

Contents

01

03

04

06

07

08

09

11

15

18

19

22

23

Original Instructions * The picture is for reference only. Please refer to the actual product for more details.

4 Folding and Unfolding

6 Learning to Ride

7 Charging

8 Warnings

1 Riding Safety

5 Activate the KickScooter

9 Maintenance

10 Speciﬁcations

11 Certiﬁcations

12 Trademark and Legal Statement

13 Contact

1. The KickScooter is a recreational product. Before mastering riding skills, you need to practice. Neither Ninebot Inc.

(means Ninebot (Beijing) Tech Co., Ltd. and its subsidiaries and affiliates) nor Segway Inc. is responsible for any

injuries or damage caused by a rider's inexperience or failure to follow the instructions in this document.

2. Please understand that you can reduce the risk by following all the instructions and warnings in this manual, but you

cannot eliminate all the risks. Remember that whenever you ride the KickScooter you risk injury from loss of control,

collisions, and falls. When entering into public spaces always comply with the local laws and regulations. As with

other vehicles, faster speeds require longer braking distance. Sudden braking on low traction surfaces could lead to

wheel slip, or falls. Be cautious and always keep a safe distance between you and other people or vehicles when

riding. Be alert and slow down when entering unfamiliar areas.

3. Always wear a helmet when riding. Use an approved bicycle or skateboard helmet that fits properly with the chin

strap in place, and provides protection for the back of your head.

4. Do not attempt your first ride in any area where you might encounter children, pedestrians, pets, vehicles, bicycles,

or other obstacles and potential hazards.

5. Respect pedestrians by always yielding the right of way. Pass on the left whenever possible. When approaching a

pedestrian from the front, stay to the right and slow down. Avoid startling pedestrians. When approaching from

behind, announce yourself and slow down to walking speed when passing. Please obey local traffic laws and

regulations if situation is different.

6. In places without laws comply with the safety guidelines outlined in this manual. Neither Ninebot Inc. nor Segway Inc.

is responsible for any property damage, personal injury/death, accidents, or legal disputes caused by violations of

the safety instructions.

7. Do not allow anyone to ride your KickScooter on his/her own unless they have carefully read this manual and

followed the New Rider Tutorial in the App. The safety of new riders is your responsibility. Assist new riders until they

are comfortable with the basic operation of the KickScooter. Make sure each new rider wears a helmet and other

protective gear.

8. Before each ride check for loose fasteners and damaged components. If the KickScooter makes abnormal sounds or

signals an alarm, immediately stop riding. Diagnose your KickScooter via the Segway-Ninebot App and call your

dealer/distributor for service.

9. Be alert! Scan both far ahead and in front of your KickScooter — your eyes are your best tool for safely avoiding

obstacles and low traction surfaces (including, but not limited to, wet ground, loose sand, loose gravel, and ice).

10. To reduce risk of injury, you must read and follow all “CAUTION” , “WARNING” and "" notices in this document.

Do not ride at an unsafe speed. Under no circumstance should you ride on roads with motor vehicles. The

manufacturer recommends riders be 14+ years old. Always follow these safety instructions:

1 Riding Safety A. People who should not ride the KickScooter include:

i. Anyone under the influence of alcohol or drugs.

ii. Anyone who suffers from disease that puts them at risk if they engage in strenuous physical activity.

iii. Anyone who has problems with balance or with motor skills that would interfere with their ability to maintain

balance.

iv. Anyone whose weight is outside the stated limits (see Specifications).

v. Pregnant women.

B. Riders under the age of 14 years old should ride under adult supervision.

C. Comply with local laws and regulations when riding this product. Do not ride where prohibited by local laws.

D. To ride safely, you must be able to clearly see what is in front of you and you must be clearly visible to others.

E. Do not ride in the snow, in the rain, or on roads which are wet, muddy, icy, or that are slippery for any reason. Do

not ride over obstacles (sand, loose gravel, or sticks). Doing so could result in a loss of balance or traction and

could cause a fall.

11. Do not attempt to charge your KickScooter if, the charger or the power outlet, is wet.

12. As with any electronic device, use a surge protector when charging to help protect your KickScooter from damage

due to power surges and voltage spikes. Only use the Segway supplied charger. Do not use a charger from any other

product models.

13. Use only Ninebot or Segway approved parts and accessories. Do not modify your KickScooter. Modifications to your

KickScooter could interfere with the operation of the KickScooter, could result in serious injury and/or damage, and

could void the Limited Warranty.

14. Children should not play with the KickScooter or parts of it nor should cleaning or maintenance be done by children.

The use of the machine results in the transmission of vibrations throughout the driver's body.

15. Always place the KickScooter on its kickstand on a flat and stable surface. The KickScooter must be placed with the

kickstand against the slope to prevent it from tipping over. Never place the KickScooter with the front facing down

the slope, which may cause your vehicle to tip over. Once the KickScooter is stably parked, check its stability to

avoid any risk of falling (by slip, wind or slight jolt). Do not park the KickScooter in a busy area, but rather along a

wall.

16. For a better riding experience, it is recommended to conduct a regular maintenance of the product.

17. Please read the user manual before charging the battery.

18. Do not touch the brake system, it could cause injuries.

19. The A-weighted emission sound pressure level is less than 70 dB(A). The mechanical vibrations transmitted by the

KickScooter are less than 2 5 m/s2.

01 02

2 Packing List

When unpacking your KickScooter, please verify that the above items are included in the package. If you are missing any

components, please contact your dealer/distributor or nearest service center (see Contact in the user manual). After

verifying that all components are present and in good condition, you can assemble your new KickScooter.

Please retain the box and packaging materials in case you need to ship your KickScooter in the future.

Remember to power o your KickScooter and unplug the charge cable before assembling, mounting accessories, or

cleaning the mainframe.

User Manual ×1

USER MANUAL QUICK START

KickScooter KickScooter Case

Accessories

3 Diagram

Power Switch / Fender Brake:

● Step on the Power Switch / Fender Brake to power on.

● When power-on and speed is less than 1.9 mph (3 km/h), step on to turn on/off the headlight.

● When power-on and speed is less than 1.9 mph (3 km/h), step on twice to switch speed modes.

● Step on the Power Switch / Fender Brake 3 secs to power off.

The rear fender can be used as a brake. It is recommended to use together with the electric brake.

Ambient Light:

It will flash when the KickScooter is still and will always be on when riding.

Electric Honk:

Press the electronic throttle and electric brake together to honk.

Quick Start ×1

Limited

Warranty

Limited Warranty ×1 Battery Charger ×1

* It can be used for placing the KickScooter.

Please do not discard it.

Electronic Throttle

Electric Brake

Dashboard Foldable Handle

Pylon

Folding Switch

Headlight

Baseboard

Kickstand

Charge Port

Battery Compartment

Hub motor

* The color of ambient light can be customized via Segway-Ninebot App.

Ambient Light

Rear Light

Power Switch / Fender Brake

(multi-functional)

03 04

4 Folding and Unfolding

Dashboard

Unfolding

Folding

Speedometer: Display the current speed of the KickScooter, as well as error codes.

Error Display: The lit wrench icon indicates the scooter error.

Cruise Control: Enabled when riding at a constant speed for 5 secs. You can exit the mode by braking.

Bluetooth: A blinking Bluetooth icon indicates that the vehicle is ready to connect. A solid Bluetooth icon

indicates that the vehicle is connected to a mobile device.

Overheat Warning: The thermometer icon always on indicates that the battery temperature has reached 122°F (50°C).

* At this point, the vehicle cannot accelerate normally and may not be charged. Do not use it until the temperature is

lowered to normal range.

Battery Level: The total battery level equals to 4 bars. Each bar equates to approximately 25% battery level.

* The battery power is very low when the first battery bar is red. Please charge your KickScooter immediately.

1. Press the folding switch and lift

up the pylon until you hear a

click.

2. Unfold the kickstand to support

the scooter. 3. Rotate both sides to align the

foldable handle.

* The KickScooter will power off once folded.

* Please press the upper folding switch.

1. Press the folding switch 2. Put down the pylon to the baseboard with the

sound of "click".

Pedestrian Mode

Modes: Step on the Power Switch / Fender Brake twice to switch between the four modes.

: Energy saving mode [Max. speed is 6.2 mph (10 km/h) with smooth acceleration, suitable for beginners];

: Standard mode [Max. speed is 9.3 mph (15 km/h)];

: Sport mode [Max. speed is 12.4 mph (20 km/h), powerful, only recommended for skilled riders].

Pedestrian mode: Max. speed is 3.7 mph (6 km/h) with flashing rear light.

Speedometer

Energy saving Mode

Standard Mode

Sport Mode

Cruise Control

Bluetooth

Headlight

Overheat Warning

Error Display

Battery Level

05 06

6 Learning to Ride

Wear an approved helmet and other protective

gear to minimize any possible injury.

Note: Please check the power level. Charge the

scooter if the battery level is low.

2. Stand stably on the baseboard with both

feet. Press the throttle to speed up when

you are balanced.

Note, For your safety, the motor will not

engage until the scooter reaches 1.86 mph

(3 km/h).

1. Stand on the baseboard with one foot

and push off with the other to start

gliding.

5 Activate the KickScooter

There are safety risks when learning to ride the KickScooter. You must read the

Riding Safety via the App before your first ride.

For your safety, your new KickScooter is not activated and will beep constantly after

Power ON.

Until activated, the Kickscooter is limited to 9.3 mph (15 km/h) and cannot be ridden

with full function. Install the App on your mobile device (with Bluetooth 4.1 or above),

connect to the KickScooter with Bluetooth, and follow the App instructions to activate

your KickScooter and enjoy the full performance.

Scan the QR code to download the App (iOS 9.0 or above, Android™ 4.3 or above).

21 Install the App and register/login. Power on the KickScooter. A blinking

Bluetooth icon indicates the KickScooter is

waiting for a connection.

Segway-Ninebot App

3

4

Click “Vehicle”→“Search vehicle” to connect to

your KickScooter.

The KickScooter will beep when the connection

is successful. The Bluetooth icon will stop

blinking and remain illuminated.

Follow the App instructions to active the KickScooter and learn how to ride safely.

You can also check the vehicle's status in App, and interact with other users. Have fun!

Vehicle Fans Moments MeDiscover

07 08

09 10

3. Slow down by releasing the throttle.

To stop, press the electric brake and

step on the fender brake at the same

time to trigger mechanical braking.

4. To turn, shift your body weight and

turn the handle slightly.

WARNING

When braking rapidly, you risk serious injury due to loss of traction and falls. Maintain a moderate

speed and look out for potential hazards.

7 Charging

Unfold the kickstand. Insert the charge plug, and

unplug your battery charger

when finished.

Kickstand

Your KickScooter is fully charged when the LED on the charger changes from red (charging) to green (trickle

charge).

WARNING

Do not charge if the charge port or charge cable is wet.

Do not charge or use your battery if it is damaged or see trace of water. Close the charge port cover when

not charging.

Do not charge outdoors.

Battery Charger

8 Warnings

DO NOT ride on public roads,

motorways, or highways.

Always wear a helmet when riding. DO NOT park in open air or outdoors.

DO NOT use mobile phone or wear

earphones when operating the KickScooter.

The KickScooter is for one rider only. DO

NOT carry any passengers. DO NOT carry

a child. DO NOT ride when pregnant.

DO NOT ride the scooter with only one foot

or one hand. DO NOT take your hands off

the foldable handle while riding.

Keep your speed between 3.1–6.2 mph

(5–10 km/h) when you ride through

speed bumps, elevator door stills, bumpy

roads or other uneven surfaces. Slightly

bend your knee to better adjust to

mentioned surfaces.

DO NOT press the Folding switch

when pushing or lifting KickScooter.

11 12

DO NOT wear high heels. Watch your head when passing

through doorways.

DO NOT ride the scooter in the rain.

Watch your speed when traveling downhill.

Use both brakes together when traveling

at high speed.

DO NOT press the throttle when

walking with the KickScooter.

DO NOT carry heavy objects on the

foldable handles.

DO NOT rotate the handle violently

while driving at high speed.

Avoid contacting obstacles with the

tire/wheel.

13 14

DO NOT ride up and down stairs or

jump over obstacles.

DO NOT ride through puddles or any

other (water) obstacles. In such a

case, please lower your speed and

bypass the obstacle.

DO NOT overtake.

DO NOT touch the hub motor after

riding because it can get hot.

9 Maintenance

Cleaning and Storage

Use a soft, wet cloth to wipe the mainframe clean. Dirt is hard to remove that is can be scrubbed with a toothbrush and

toothpaste, then cleaned with a soft, wet cloth.

NOTE

Do not wash your KickScooter with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances

may damage the appearance and internal structure of your KickScooter. Do not wash your KickScooter with a power

washer or hose.

WARNING

Make sure the KickScooter is powered OFF, the charge cable is unplugged, and the rubber cap on the charge port is

tightly sealed before cleaning; otherwise you may damage the electronic components.

Store your KickScooter in a cool, dry place. Do not store it outdoors for extended periods of time. Exposure to sunlight

and temperature extremes (both hot and cold) will accelerate the aging process of the plastic components and may

reduce battery life.

Replace the Tires

Tires supplied with the product are to be mounted on the wheel by a professional repairer. Removing the wheels is

complicated and incorrect assembly can lead to instability and malfunctions:

– Please contact an authorized repairer if the product is still under manufacturer warranty. You can ask for the list of the

authorized repairers to the customer service available at www.segway.com.

– If the product is no longer under warranty you can contact any specialized repairer of your choice.

– Should you have questions, you can contact customer service available at www.segway.com.

Maintenance and Removal of the Battery

Do not remove the battery. Removing the battery is complicated and can alter its operation: You can contact an

authorized repairer if the product is still under warranty. If it is not, you can contact any specialized repairer of your

choice. You can ask for the list of the authorized repairers to the customer service available. For any further question,

you can contact the customer service.

Do not store or charge the battery at temperatures outside the stated limits (see Specifications). Do not puncture the

battery. Refer to your local laws and regulations regarding battery recycling and/or disposal.

A well maintained battery can perform well even after many miles of riding. Charge the battery after each ride and avoid

draining the battery completely. When used at room temperature (70°F [22°C]) the battery range and performance is at

its best; whereas using it at temperatures below 32°F (0°C) can decrease range and performance. Typically, at -4°F

(-20°C) range can be half that of the same battery at 70°F (22°C). Battery range will recover when temperature rises.

More details are available in the App.

NOTE

Typically, a fully charged battery should retain power for 120-180 days. A low-power battery should retain power for

30–60 days. Remember to charge the battery after each use. Completely draining the battery may cause permanent

damage to the battery. Electronics inside the battery record the charge-discharge condition of the battery; damage

caused by over-charging or under-charging will not be covered by the Limited Warranty.

WARNING

Do not attempt to disassemble the battery. Do not touch battery contacts. Do not dismantle or puncture the casing.

Keep the battery contacts away from metal objects to prevent short circuit. Risk of fire. No user serviceable parts. Do

not charge or use your battery if it is damaged or see trace of water.

WARNING

Do not ride when the ambient temperature is outside the machine operation temperature (see Specifications) because

low/high temperature will limit the maximum power/torque. Doing so could cause personal injury or property damage

due to slips or falls.

Others

The external flexible cable of this transformer cannot be replaced; if the cord is damaged, the transformer must be

discarded and replaced by a new one. Should you have questions, you can contact customer service available at

www.segway.com.

In case of an accident or breakdown, please contact an authorized repairer if the product is still under warranty. If not,

you can contact any specialized repairer of your choice. You can ask for the list of the authorized repairers from the

customer service available at www.segway.com.

Efforts have been made to simplify wording in the user manual. When an action appears too complicated, you are

advised to contact an authorized or a specialized repairer or customer service.

15 16

Cleaning and Storage

Use a soft, wet cloth to wipe the mainframe clean. Dirt is hard to remove that is can be scrubbed with a toothbrush and

toothpaste, then cleaned with a soft, wet cloth.

NOTE

Do not wash your KickScooter with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances

may damage the appearance and internal structure of your KickScooter. Do not wash your KickScooter with a power

washer or hose.

WARNING

Make sure the KickScooter is powered OFF, the charge cable is unplugged, and the rubber cap on the charge port is

tightly sealed before cleaning; otherwise you may damage the electronic components.

Store your KickScooter in a cool, dry place. Do not store it outdoors for extended periods of time. Exposure to sunlight

and temperature extremes (both hot and cold) will accelerate the aging process of the plastic components and may

reduce battery life.

Replace the Tires

Tires supplied with the product are to be mounted on the wheel by a professional repairer. Removing the wheels is

complicated and incorrect assembly can lead to instability and malfunctions:

– Please contact an authorized repairer if the product is still under manufacturer warranty. You can ask for the list of the

authorized repairers to the customer service available at www.segway.com.

– If the product is no longer under warranty you can contact any specialized repairer of your choice.

– Should you have questions, you can contact customer service available at www.segway.com.

Maintenance and Removal of the Battery

Do not remove the battery. Removing the battery is complicated and can alter its operation: You can contact an

authorized repairer if the product is still under warranty. If it is not, you can contact any specialized repairer of your

choice. You can ask for the list of the authorized repairers to the customer service available. For any further question,

you can contact the customer service.

Do not store or charge the battery at temperatures outside the stated limits (see Specifications). Do not puncture the

battery. Refer to your local laws and regulations regarding battery recycling and/or disposal.

A well maintained battery can perform well even after many miles of riding. Charge the battery after each ride and avoid

draining the battery completely. When used at room temperature (70°F [22°C]) the battery range and performance is at

its best; whereas using it at temperatures below 32°F (0°C) can decrease range and performance. Typically, at -4°F

(-20°C) range can be half that of the same battery at 70°F (22°C). Battery range will recover when temperature rises.

More details are available in the App.

NOTE

Typically, a fully charged battery should retain power for 120-180 days. A low-power battery should retain power for

30–60 days. Remember to charge the battery after each use. Completely draining the battery may cause permanent

damage to the battery. Electronics inside the battery record the charge-discharge condition of the battery; damage

caused by over-charging or under-charging will not be covered by the Limited Warranty.

WARNING

Do not attempt to disassemble the battery. Do not touch battery contacts. Do not dismantle or puncture the casing.

Keep the battery contacts away from metal objects to prevent short circuit. Risk of fire. No user serviceable parts. Do

not charge or use your battery if it is damaged or see trace of water.

WARNING

Do not ride when the ambient temperature is outside the machine operation temperature (see Specifications) because

low/high temperature will limit the maximum power/torque. Doing so could cause personal injury or property damage

due to slips or falls.

Others

The external flexible cable of this transformer cannot be replaced; if the cord is damaged, the transformer must be

discarded and replaced by a new one. Should you have questions, you can contact customer service available at

www.segway.com.

In case of an accident or breakdown, please contact an authorized repairer if the product is still under warranty. If not,

you can contact any specialized repairer of your choice. You can ask for the list of the authorized repairers from the

customer service available at www.segway.com.

Efforts have been made to simplify wording in the user manual. When an action appears too complicated, you are

advised to contact an authorized or a specialized repairer or customer service.

10 Speciﬁcations

Dimensions

Machine

Battery

Motor

Charger

Features

Tire

Brake Light

Length x Width x Height

Payload

Rider Recommended Age

Required Height

Max. Speed

Typical Range [1]

Max. Slope

Operating Temperature

Storage Temperature

IP Rating

Duration of Charging

Traversable Terrain

Max. Charging Voltage

Nominal Capacity 4000 mAh

Nominal Energy

Battery Management System

Input Voltage

Output Voltage

Output Current

Nominal Voltage

Nominal Power

Output Power

Approx. 36.9 × 15.7 × 40.0 in (936 × 398 × 1015 mm)

66.1–220.5 lbs (30.0–100.0 kg)

Approx. 7.5 miles (12 km)

Approx. 15%

36 V

14–104°F (-10–40°C)

-4–122°F (-20–50°C)

42 V

144 Wh

0.25 kW, 250 W

Over-heating, short circuit, over-current, over-discharge, and

over-charge protection

100–240 V

42 V

1.7 A

0.071 kW, 71 W

14–60 years

4’3”–6’6” (130–200 cm)

IPX4

Approx. 4 h

asphalt/flat pavement; obstacles < 0.4 in (1 cm);

gaps < 1.2 in (3 cm)

Approx. 12.4 mph (20 km/h)

LED rear light

Riding Modes

Tires

Pedestrian mode, Energy saving mode, Standard mode and

Sport mode

Tire diameter: Ø246±3 mm Cross section width: 58±2 mm

Tread pattern: Twill Inflation-free/filled with foaming PU

Folded: Length x Width x Height Approx. 40.3 × 8.0 × 8.8 in (1024 × 202 × 223 mm)

[1]

Typical Range: tested while riding under full power, 165.3 lbs (75.0 kg) load, 77°F (25°C), 7.5 mph (12 km/h) on average on pavement.

Product Model

Net Weight

Name Ninebot KickScooter

Air T15

Approx. 23.2 lbs (10.5 kg)

Item Parameter

17 18

11 Certiﬁcations

This product is certified to ANSI/CAN/UL-2272 by TUV Rheinland.

The battery complies with UN/DOT 38.3.

The battery complies with ANSI/UL 2271.

Federal Communications Commission (FCC) Compliance Statement for USA

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Industry Canada (IC) Compliance Statement for Canada

This device complies with Industry Canada license-exempt RSS standard (s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

CAN ICES-3 (B)/NMB-3(B)

“Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement."

Neither Segway Inc. nor Ninebot is responsible for any changes or modifications not expressly approved by Segway Inc.

or Ninebot. Such modifications could void the user's authority to operate the equipment.

FCC ID: 2ALS8-KS0002

IC: 22636-KS0002

19 20

Important WEEE information

WEEE Disposal and Recycling Information Correct Disposal of this product. This marking indicates that this product

should not be disposal with other household wastes throughout the EU.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsible

to promote the sustainable reuse of materials resources. To return your used device, please use the return and

collection systems or contact the retailer where the product was purchased. They can take this product for environmen-

tal safe recycling.

Battery recycling information for the European Union

Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC and amendment

2013/56/EU concerning batteries and accumulators and waste batteries and accumulators. The Directive determines

the framework for the return and recycling of used batteries and accumulators as applicable throughout the European

Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather

reclaimed upon end of life per this Directive.

In accordance with the European Directive 2006/66/EC and amendment 2013/56/EU, batteries and accumulators are

labeled to indicate that they are to be collected separately and recycled at end of life. The label on the battery may also

include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium).

Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste, but

use the collection framework available to customers for the return, recycling, and treatment of batteries and

accumulators. Customer participation is important to minimize any potential effects of batteries and accumulators on

the environment and human health due to the potential presence of hazardous substances.

Before placing electrical and electronic equipment (EEE) in the waste collection stream or in waste collection facilities,

the end user of equipment containing batteries and/or accumulators must remove those batteries and accumulators

for separate collection.

12 Trademark and Legal Statement

Ninebot is the registered trademark of Ninebot (Tianjin) Tech Co., Ltd; Segway and the Rider Design are the registered

trademarks of Segway Inc.; Android, Google Play are trademarks of Google Inc., App Store is a service mark of Apple

Inc., The respective owners reserve the rights of their trademarks referred to in this manual.

The KickScooter is covered by relevant patents. For patent information go to http://www.segway.com.

We have attempted to include descriptions and instructions for all the functions of the KickScooter at the time of

printing. However, due to constant improvement of product features and changes of design, your KickScooter may

differ slightly from the one shown in this document. Visit the Apple App Store (iOS) or the Google Play Store (Android)

to download and install the App.

Please note that there are multiple Segway and Ninebot models with different functions, and some of the functions

mentioned herein may not be applicable to your unit. The manufacturer reserves the right to change the design and

functionality of the KickScooter product and documentation without prior notice.

21 22

Restriction of Hazardous Substances (RoHS) Directive

This Ninebot (Changzhou) Tech Co., Ltd. product, with included parts (cables, cords, and so on) meets the require-

ments of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic

equipment (“RoHS recast” or “RoHS 2”).

Radio Equipment Directive

Segway Europe BV, Hogehilweg 8, 1101 CC Amsterdam, The Netherlands.

Hereby, [Ninebot (Changzhou) Tech Co., Ltd,] declares that the radio equipment type [Air T15] is in compliance with

Directive 2014/53/EU.

Bluetooth Max. RF Power

Frequency Band(s)

100mW

2.4000–2.4835GHz

13 Contact

Contact us if you experience issues relating to riding, maintenance and safety, or errors/faults with your KickScooter.

Americas:

Segway Inc.

14 Technology Drive, Bedford, NH 03110, USA

Toll Free: 1-866-473-4929

Fax: 1-603-222-6001

Technical Support Email: [email protected]

Website: www.segway.com

Europe, Middle East and Africa:

Segway Europe B.V.Hogehilweg 8, 1101CC Amsterdam, The Netherlands

Website: www.segway.com

Have your KickScooter serial number on hand when contacting Segway.You can find your serial number on the

underside of your KickScooter or in the App under More Settings –> Basic Information.

23 24

The manufacturer reserves the right to make changes to the product, release firmware updates, and update this

manual at any time. Visit www.segway.com or check the App to download the latest user materials. You must install

the App, activate your KickScooter, and obtain the latest updates and safety instructions.

www.segway.com

Air T15

Ninebot KickScooter

Manuel utilisateur

2 Liste d'emballage

3 Diagramme

01

03

04

06

07

08

09

11

15

18

19

22

23

* La photo est pour référence seulement. Veuillez vous référer au produit réel pour plus de détails.

4 Pliage et dépliage

6 Apprendre à conduire

7 Chargement

8 Avertissements

1 Sécurité

5 Activez le KickScooter

9 Entretien

10 Spéciﬁcations

11 Certiﬁcations

12 Marque commerciale et déclaration juridique

13 Contact

Traduction des instructions originales

Nous vous remercions d'avoir choisi le Ninebot KickScooter Max (ci-après dénommé KickScooter)!

Votre KickScooter est un dispositif de transport élégant avec une application mobile vous permettant

de vous connecter à d'autres conducteurs.

Savourez le trajet et connectez-vous à des conducteurs à travers le monde!

Nous vous remercions d'avoir choisi le Ninebot KickScooter Max!

Sommaire

1 Sécurité

1. Le KickScooter est un dispositif de transport conçu pour la récréation. En maîtriser la conduite demande de

l'entraînement. Ninebot Inc. et Segway Inc. déclinent toute responsabilité en cas de blessure ou dommage causé

par le manque d'expérience d'un conducteur ou par le non-respect des instructions contenues dans ce document.

2. Veuillez noter qu'il est possible de réduire les risques en suivant l'ensemble des instructions et avertissements

contenus dans ce manuel, mais qu'il n'est pas possible d'éliminer tous les risques. Rappelez-vous que lorsque vous

utilisez le KickScooter, vous vous exposez à un risque de blessure en cas de perte de contrôle, collision ou chute.

Lorsque vous pénétrez des espaces publics, conformez-vous toujours aux lois et règlements applicables. Comme

pour les autres véhicules, la distance nécessaire au freinage augmente avec la vitesse. Un freinage brusque sur des

surfaces à faible adhérence peut entraîner un patinage des roues ou une chute. Soyez prudents et conservez

toujours une distance suffisante entre vous et les autres personnes ou véhicules lorsque vous conduisez. Soyez

attentifs et ralentissez lorsque vous pénétrez des lieux qui ne vous sont pas familiers.

3. Portez toujours un casque lorsque vous conduisez. Utilisez un casque homologué pour vélo ou skateboard, de taille

adaptée, avec la mentonnière en place, protégeant l'arrière de votre tête.

4. Ne réalisez pas votre premier essai dans un lieu où vous pourriez rencontrer des enfants, des piétons, des animaux

de compagnie, des véhicules, des cyclistes ou d'autres obstacles et dangers potentiels.

5. Respectez les piétons en leur laissant toujours la priorité. Doublez à gauche si possible. Lorsque vous approchez un

piéton de l'avant, restez à droite et ralentissez. Évitez de surprendre les piétons. Lorsque vous approchez par

derrière, annoncez-vous et ralentissez de sorte à atteindre une vitesse de marche pour doubler. Dans les autres

situations, veuillez respecter les lois et règlements concernant la circulation routière.

6. Dans les lieux où les lois ne s'appliquent pas, respectez les consignes de sécurité présentées dans ce manuel.

Ninebot Inc. et Segway Inc. déclinent toute responsabilité en cas de dommages matériels, dommages corporels/

décès, accidents ou litiges juridiques résultant de violations des consignes de sécurité.

7. Ne permettez à personne d'utiliser votre KickScooter seul à moins qu'il ou elle n'est lu attentivement ce manuel et

suivi le tutoriel Nouveau conducteur dans l'application. La sécurité des nouveaux utilisateurs relève de votre

responsabilité. Aidez les nouveaux utilisateurs jusqu'à ce qu'ils soient à l'aise avec le maniement de base du

KickScooter. Assurez-vous que chaque nouvel utilisateur porte un casque et d'autres équipements de protection.

8. Avant chaque utilisation, assurez-vous qu'il n'y ait pas fixations desserrées et de composants endommagés. Si le

KickScooter produit des bruits anormaux ou émet une alarme, cessez immédiatement l'utilisation. Effectuez un

diagnostic de votre KickScooter via l'application Segway-Ninebot et appelez votre revendeur-/-distributeur pour la

réparation.

9. Soyez attentifs! Regardez au loin et devant votre KickScooter: vos yeux sont votre meilleur outil sécurité pour éviter

les obstacles et les surfaces à faible traction (y compris, mais sans s'y limiter, les sols mouillés, le sable, le gravier et

le verglas).

10. Pour réduire le risque de blessure, vous devez lire et suivre tous les avis «ATTENTION» et «AVERTISSEMENT» dans

ce document. Ne conduisez pas à une vitesse dangereuse. Vous ne devez conduire en aucune circonstance sur la

route avec des véhicules motorisés. L’âge recommandé par le fabricant est de 14+ ans. Suivez toujours les

consignes de sécurité:

A. Les personnes devant s'abstenir de conduire le KickScooter incluent:

i. Toute personne se trouvant sous l'emprise de l'alcool ou de drogues.

ii. Toute personne souffrant d'une maladie qui la met en danger lorsqu'elle pratique une activité physique

intense.

iii. Toute personne ayant des problèmes d'équilibre ou d'habileté motrice pouvant lui faire perdre l'équilibre.

iv. Toute personne dont le poids est en dehors des limites indiquées (voir Spécifications).

v. Les femmes enceintes.

B. Les conducteurs de moins de 14 ans doivent être supervisés par un adulte.

C. Conformez-vous aux lois et règlements applicables lorsque vous utilisez ce produit. Ne conduisez pas sur des

sites interdits par les lois applicables.

D. Pour conduire de manière sûre, vous devez être en mesure de voir clairement ce qui se trouve devant vous et

vous devez être clairement visible pour les autres.

E. Ne conduisez pas dans la neige ou sous la pluie ou sur des chaussées mouillées, boueuses, glacées ou glissantes,

pour quelque raison que ce soit. Ne conduisez pas sur des obstacles (sable, gravier ou bouts de bois). Cela pourrait

causer une perte d'équilibre ou de traction pouvant entraîner une chute.

11. N'essayez pas de charger votre KickScooter si ce dernier, le chargeur ou la prise de courant est mouillé(e).

12. Comme pour tout appareil électronique, utilisez un dispositif antisurtension lors de la charge pour protéger votre

KickScooter de tout dommage dû aux pics d'intensité et pointes de tension. Utilisez uniquement le chargeur fourni

par Segway. N'utilisez pas de chargeur conçu pour un modèle différent.

13. Utilisez uniquement des pièces et accessoires homologué(e)s par Ninebot ou Segway. Ne modifiez pas votre

KickScooter. Le fait d'apporter des modifications à votre KickScooter peut nuire au bon fonctionnement du

KickScooter, peut entraîner des blessures et/ou dommages graves et peut entraîner la révocation de la Garantie

limitée.

14. Les enfants ne peuvent jouer avec la trottinette ou des parties de celle-ci. Le nettoyage ou l'entretien ne peut être

effectué par des enfants. L'utilisation de la machine entraîne la transmission de vibrations dans l'ensemble du

corps du conducteur.

15. Placez toujours la trottinette sur sa béquille sur une surface plane et stable. La trottinette doit être placée avec la

béquille à contre-pente afin d’éviter tout basculement. Ne placez jamais la trottinette avec l'avant face à la pente,

la béquille pourrait se refermer et faire basculer la machine. Une fois la trottinette sur sa béquille, vérifiez sa

stabilité afin d’éviter tout risque de chute (par glissement, vent ou léger à-coup). Ne stationnez pas la trottinette

dans un endroit passant mais privilégiez plutôt le long d’un mur. Dans la mesure du possible, choisissez toujours

de stationner sa trottinette sur un sol plat.

16. Pour une meilleure expérience de conduite, il est conseillé d'effectuer l'entretien régulier du produit.

17. Veuillez lire le manuel d'utilisation avant de charger la batterie.

18. Ne touchez pas au système de freinage, cela peut entraîner des blessures.

19. Le niveau de pression acoustique d'émission pondéré A est inférieur à 70 dB (A). Les vibrations mécaniques

transmises par le KickScooter sont inférieures à 2,5 m/s2.

01 02

Lorsque vous déballez votre KickScooter pour la première fois, veuillez vériﬁer que les articles ci-dessus sont inclus dans

l'emballage. S'il vous manque des composants, veuillez contacter votre revendeur/distributeur ou le centre de service le

plus proche (voir la section Contacts du manuel utilisateur). Après avoir vériﬁé que tous les composants sont présents et

en bon état, vous pouvez assembler votre nouveau KickScooter.

Veuillez conserver la boîte et l'emballage au cas où vous auriez besoin de faire expédier votre KickScooter à l'avenir.

Rappelez-vous d'éteindre votre KickScooter et de débrancher le cordon d'alimentation avant l'assemblage, le montage des

accessoires ou le nettoyage de la pièce centrale.

Manuel Utilisateur ×1

MANUEL UTILISATEUR

DÉMARRAGE RAPIDE

Accessoires

Interrupteur d'alimentation/Frein d'aile :

● Appuyez sur l'interrupteur/le frein d'aile pour mettre en marche.

● Lorsque le moteur est allumé et que la vitesse est inférieure à 3 km/h, appuyez sur le bouton pour allumer ou

éteindre le phare.

● Lorsque le moteur est allumé et que la vitesse est inférieure à 3 km/h (1,9 mph), appuyez deux fois sur le bouton

pour changer de mode de vitesse.

● Appuyez sur l'interrupteur d'alimentation/ le frein d'aile pendant 3 secondes pour couper l'alimentation.

L’aile arrière peut être utilisée comme frein. Il est recommandé de l’utiliser ensemble avec le frein électronique.

Lumière ambiante :

Il clignotera lorsque le KickScooter est immobile et restera allumé lors de la conduite.

Klaxon électrique :

Appuyez ensemble sur l'accélérateur électronique et le frein électronique pour klaxonner.

Accélérateur électronique

Interrupteur d'alimentation/Frein d'aile

(multifonctions)

Marche Frein électronique

Tableau de bord Poignée pliable

Pylône

Levier de pliage

Phare avant

Lumière ambiante

Plinthe

Béquille

Port de charge Feu arrière

Réceptacle de la batterie

Moteur du

moyeu

Démarrage Rapide ×1

2 Liste d'emballage 3 Diagramme

Chargeur de batterie ×1

KickScooter assemblé Boîte de stockage

KickScooter

*Il peut être utilisé pour placer le

KickScooter. Veuillez ne pas le jeter.

Limited Warranty ×1

GARANTIE LIMITÉE

* La couleur de la lumière ambiante peut être personnalisée via l’application Segway-Ninebot.

03 04

Tableau de bord

Compteur de vitesse : Indique la vitesse actuelle. Affiche également les codes d'erreur lorsque des

problèmes sont détectés.

Erreur : L'icône de la clé indique que le scooter a détecté une erreur.

Bluetooth : Une icône Bluetooth clignotante indique que le véhicule est prêt à être connecté. Une icône

Bluetooth fixe indique que le véhicule est connecté à un appareil mobile.

Avertissement de surchaue : l'icône du thermomètre toujours allumée indique que la température de la batterie a

atteint 50°C.

* À ce stade, le véhicule ne peut pas accélérer normalement et ne peut pas être chargé. Ne l'utilisez pas tant que la température

n'est pas revenue à la normale.

Régulateur de vitesse : Activé lorsque vous roulez à vitesse constante pendant 5 secondes. Vous pouvez

quitter le mode en freinant.

Niveau de puissance : Le niveau total de la batterie équivaut à 4 barres. Chaque barre équivaut à environ 25 % de

niveau de puissance.

* La puissance de la batterie est très faible lorsque la première barre de batterie est rouge. Veuillez recharger votre

KickScooter immédiatement.

Mode piéton

Modes : Appuyez deux fois sur l'interrupteur d'alimentation / le frein d'aile pour passer d'un mode à l'autre.

: Mode d’économie d’énergie [La vitesse maximale est de 6.2 mph (10 km/h) avec une accélération en douceur, adaptée

aux débutants];

: Mode standard [La vitesse maximale est de 9.3 mph (15 km/h)];

: Mode sport [La vitesse maximale est de 12.4 mph (20 km/h), puissant, recommandé uniquement pour les conducteurs

expérimentés].

Compteur de vitesse

Mode d’ économie d’ énergie

Mode standard

Mode sport

Bluetooth

Régulateur de vitesse

Phare avant

Avertissement de surchauffe

Erreur

4 Pliage et dépliage

Niveau de puissance

Dépliage

Repliement

1. Appuyez sur le levier de pliage et

soulevez le pylône jusqu’à ce

que vous entendiez un clic.

2. Déplier la béquille pour soutenir

le scooter. 3. Faire pivoter les deux côtés

pour aligner la poignée pliable.

1. Appuyez sur le levier de pliage. 2. Posez le pylône à la plinthe avec le son du « clic ».

Mode piéton: La vitesse maximale est de 3.7 mph (6 km/h) avec un feu arrière clignotant.

* Veuillezappuyer sur le levier de pliage

supérieur.

* Le KickScooter s’éteint une fois plié.

05 06

5 Activez le KickScooter

21 Installez l'application et inscrivez-vous ou

identifiez-vous.

Allumez le KickScooter. Une icône

Bluetooth clignotante indique que le

KickScooter est en attente de connexion.

3

4

Cliquez sur «Rechercher un véhicule» pour vous

connecter à votre KickScooter. Le KickScooter

émet un son lorsque la connexion est réussie.

L'icône Bluetooth arrête de clignoter et reste

illuminée.

Suivez les instructions de l'application pour activer le KickScooter et apprenez comment le manier avec

prudence.

Vous pouvez maintenant commencer à utiliser votre KickScooter, vérifiez le statut dans l'application et

interagissez avec les autres utilisateurs. Amusez-vous bien!

Vehicle Fans Moments MeDiscover

6 Apprendre à conduire

Le fait d'apprendre à utiliser le KickScooter pose des risques de sécurité.

Lisez les Sécurité dans la conduite dans l'application avant votre première utilisation.

Pour votre sécurité, votre KickScooter n'est pas activé et il émettra occasionnellement un

son après l'avoir mis sur ON.

Tant qu'il n'est pas activé, le KickScooter conserve une vitesse de marche très faible et ses

pleines fonctionnalités ne peuvent pas être utilisées.

Installez l'application sur votre appareil mobile (avec Bluetooth 4.0 ou ultérieur),

connectez-le au KickScooter par Bluetooth, et suivez les instructions de l'application pour

activer votre KickScooter pour bénéficier de la pleine performance.

Scannez le code QR pour télécharger l'application.

Segway-Ninebot App

Remarque: Veuillez vérifier le niveau de batterie sur

l'écran. Chargez le scooter si le niveau

de la batterie est faible.

Portez un casque homologué et d’autres

équipements de protection afin de minimiser

toute blessure éventuelle.

1. Tenez-vous sur l'appui-pieds avec un

pied et poussez avec votre autre pied

pour commencer à glisser.

2. Placez votre autre pied sur l'appui-pieds pour

assurer la stabilité des deux pieds. Appuyez sur

l'accélérateur de la main droite pour accélérer

lorsque vous avez trouvé votre équilibre.

Remarque: pour assurer votre sécurité, le

moteur ne s'embrayera pas jusqu'à ce que le

KickScooter atteigne la vitesse 1.86 mph

(3 km/h).

07 08

La pagina si sta caricando...

Ninebot Air T15 Manuale utente

Ninebot Air T15 Manuale utente

in altre lingue

Documenti correlati

Altri documenti