Tracplus RockAIR Reliable and Affordable Aircraft Tracking Device Manuale del proprietario
- Tipo
- Manuale del proprietario
RockAIR
Owner’s Manualv3.0a
3
Overview
Thank you for your purchase of a RockAIR. We are confident that you will find the RockAIR
to be an invaluable addition to your operations to improve safety, communication and
operational eectiveness.
With correct use, your RockAIR should provide years of reliable service. This manual sets
out important information crucial to the correct installation and operation of your RockAIR so
that you get the very best results from your investment. Failure to observe and adhere to the
instructions contained in this document will compromise the ability of the RockAIR to perform
as designed.
Description
The RockAIR is a portable, carry-on carry-o global communications device that allows you
to transmit tracking, events, forms and send/receive messages from anywhere in the world
using the Iridium satellite network and terrestrial cellular networks.
The RockAIR consists of a GPS receiver, Iridium SBD satellite transceiver, GPRS cellular
modem, internal satellite/cellular/GPS antennas, Bluetooth™ module, micro-controller and
backup Li-Ion Polymer battery.
TracPlus cannot be held responsible for any failure of the RockAIR or
supporting services arising in whole or in part from any failure to adhere to
the instructions and guidelines contained herein.
A. Power/Suspend button
B. Monitor button
C. Mark button
D. Distress/Distress Cancel button
E. Power/Suspend LED indicator
F. Monitor LED indicator
G. External Power LED indicator
H. Bluetooth LED indicator
I. Mark LED indicator
J. Distress/Distress Cancel LED indicator
K. Iridium external SMA connector (optional)
L. GPS external SMA connector (optional)
M. Cellular external SMA connector (optional)
N. Sensor cable connector
O. Power cable connector
P. MicroUSB port
Q. SD card slot (front sleeve removed)
R. GPRS SIM card slot (front sleeve removed)
AB C D
E F G H I
R
Q
P
ON
MLK
J
4
Specifications
Dimensions 100 mm (W) x 119 mm (L) x 25 mm (H) (3.9” x 4.7” x 1.0”)
Weight 210 g (8 oz)
Connectors USB
4-way Molex Micro-Fit (power)
6-way Molex Micro-Fit (input sensors)
Optional SMA for external antennas
Inputs Four membrane push buttons
USB serial
Bluetooth
Five configurable digital inputs
Sensors GPS
Accelerometer
Thermometer
Power loss
Impact
Screen Type None. Pair with iOS device for features requiring screen
LED Indicators 6 NVG compatible LEDs with additional ND filters
Internal Antennas GPS, Iridium, Cellular
Casing/Housing ABS/PC (Bayblend FR3010 BLK)
Elastosil LR 3003/70 A&B
Input Voltage USB (5v DC; not for use in operation) or
Aircraft Power (9-30 V DC)
Power Consumption 500 mA max, plus very low current sleep mode (<30 mA)
Power Sources External DC supply with internal Li-Ion polymer battery backup
Satellite Network Iridium via 9603 Short Burst Data (SBD) transceiver
Cellular Network GPRS (Cellular IP)
Operating Environment < 75% Relative Humidity
Operating Temperature -40°C - +85°C
Other Certifications FCC & CE
DO160 Testing DO160G
Section 15 Magnetic Eect
Section 21.4 Conducted Emission of Radio Frequency Energy
Section 21.5 Radiated Emission of Radio Frequency
Energy DO160G
Section 4 Temperature and Altitude
Section 7.2.1 Operational Shock
Section 7.3.1 Impulse Shock
Section 7.3.3 Sustained Shock
Section 8.8.1 Vibration
Section 17 Voltage Spike
Section 26 Flammability
5
Capabilities
Tracking
● Transmit regular position reports via Iridium satellite network
● Transmit regular position reports via terrestrial cellular networks
● Automatically switch between satellite and cellular networks based on coverage
● Manually suspend tracking and automatically resume
Automated Monitoring
● Automatic monitoring with Of Concern and Overdue alerts via SMS
Marking
● Manually mark up to four dierent types of points of interest
Alerting
● Manually activate distress mode to transmit distress messages at a faster rate
● Distress notification via SMS and voice
● Manually cancel distress mode to resume normal operation
● Automatically detect and transmit impact alerts
● Automatically detect and transmit start up and shutdown messages
● Automatically detect and transmit events from external switch-type sensors
⊲ Engine start
⊲ Engine stop
⊲ Take o
⊲ Landing
⊲ Rotor start
⊲ Rotor stop
⊲ AoA limit exceedence
⊲ A range of other user-definable events
Backup Battery
● Automatically transmit queued reports and messages after shutdown
Global Messaging (connected device required)
● Send/Receive text messages to/from mapping software
● Send/Receive text messages to/from cell phones
● Send/Receive text messages to/from email addresses
Forms (connected device required)
● Complete and send custom forms to mapping software
Logging
● Position and diagnostic information recorded each second to removable
MicroSD card (included)
6
RockAIR installation
Aviation use
TracPlus does not hold any STCs or TSOs for the RockAIR. The RockAIR should be installed in
accordance with the requirements of the operator and the intended use.
Installation of the RockAIR is at the discretion of a duly licensed Aircraft Maintenance
Engineer or Aircraft Maintenance Technician (AME/AMT). The following recommendations are
appropriate for New Zealand or the United States, and may apply in other countries.
AC43-14 Appendix 9
Under New Zealand Civil Aviation Authority (CAA) Advisory Circular AC43-14 Appendix 9,
eligible aircraft can have the RockAIR installed as non-aeronautical equipment.
FAA 337
The power cable for the unit may be hardwired into the aircraft power system, and the
sensor cable may be connected to independent non-critical sensors. This is a modification
performed in the field by any approved AME/AMT by submitting an FAA 337 form or
equivalent. Whether the installation qualifies as a major modification will be at the discretion
of the FAA Flight Standards District Oce.
To support the installation process, TracPlus provides RockAIR owners with DO160G test
documentation. This is available on request from TracPlus.
For further information, please email [email protected] or call as follows:
North America (678) 782 8090
New Zealand 0800 872 275
Australia 1800 330 740
Rest of World +64 3 477 8656
7
Finding the best place
The RockAIR needs to have an uninterrupted view of the sky to operate correctly. As such,
the correct placement of the RockAIR during installation is crucial. The RockAIR should be
installed so that it is level and upright; clear of obstructions and has the greatest possible
hemispherical view of the sky.
Metal, carbon-fiber or concrete objects between the RockAIR and the sky will prevent the
RockAIR from correctly operating. The RockAIR cannot reliably gain a GPS fix or transmit and
receive data when placed inside a vehicle trunk, luggage compartment, building, or under
water.
The typical mounting position for the RockAIR is on the glare-shield of your aircraft or
dashboard of your vehicle, in such a way as to maximize the view through the canopy or
windscreen.1
If you are unable to position the RockAIR anywhere with such a view, you should consider
installing an external antenna or antennae. This is typically a dual mode GPS/Iridium antenna
and a separate cellular antenna. This requires notification at time of purchase, or a return to
your distributor for an approved modification.
Installing the mounting clip
The recommended means of installing the RockAIR is to permanently fit the provided
mounting clip to the glare-shield or dashboard, using installation-appropriate fasteners (not
included) so that the clip will not detach during an impact event.
1 The RockAIR may not operate correctly on the glare-shield of an aircraft fitted with electrically heated windows as the fine wire mesh
prevents the transmission of radio signals.
8
Adding and removing the RockAIR from the clip
To attach the RockAIR into the mounting clip, align and insert the left side of the RockAIR into
the mounting clip as shown and rotate downwards until the RockAIR clicks
into place.
To remove the RockAIR from the mounting clip, move the top of the right side of the clip away
from the RockAIR and lift the RockAIR clear.
Connecting to aircraft power (9-30 V DC)
The RockAIR must be connected to the avionics DC bus or vehicle power supply via the
4-way Molex connector on the rear of the device. An external 1 A fuse must be used when
connecting the RockAIR in this way. The RockAIR will operate correctly with a voltage of
between 9-30 V DC, and has passed DO160G testing for over-voltage and reversed polarity.
When connected to aircraft power in this way, the RockAIR will automatically turn on and o
with external power.2
Pin 1 +Ve (9-30 V DC)
Pin 2 -Ve (Ground)
Pin 3 RS232 Tx (Output)
Pin 4 RS232 Rx (Input)
As looking at the back of the RockAIR
2 This is the default behaviour of the RockAIR. Changing the configuration may change this behaviour.
9
Battery Operation
For non-aviation purposes, the RockAIR can be powered using the built-in Li-Ion Polymer
battery, and will operate for up to 8 hours on a single full charge.
Before operational use, the RockAIR should be fully charged using the USB connector and an
adapter capable of providing at least 1.3 A at 5 V DC.
When used in this way, the RockAIR must be manually turned on and o using the green
Power/Suspend button. Please contact TracPlus for recommended firmware settings when
powering the unit using the battery.
Connecting to external sensors for event tracking
The RockAIR can be connected to up to five external switch-type sensors to detect external
events, such as take-o and landing via a helicopter collective switch, or engine-start
and engine-stop via an oil pressure switch. The value and eectiveness of tracking data
is increased when the RockAIR is connected to external sensors, for example, allowing
automated and highly accurate flight and engine time reporting.
All five sensor inputs are electrically isolated digital or “switch type” inputs. There are no
analog inputs on the RockAIR.
Pin 1 - Airborne
Pin 2 - Engine 1
Pin 3 - Engine 2
Pin 4 - Brake
Pin 5 - Drop Valve
Pin 6 - Signal Ground
Open Closed
Airborne
Stopped
Stopped
Not Set
Open
Landed
Running
Running
Set
Closed
As looking at the
back of the RockAIR
Sensor inputs are activated by closing or opening the input to the common signal ground on
the connector, not to aircraft or vehicle ground. Do not connect the common signal ground to
the aircraft or vehicle ground. Closing or opening any sensor input to or from signal ground
will cause an event report to be transmitted. The default set of sensor event mappings are
shown above. Please contact TracPlus if you need to use settings other than the defaults.
By default, the RockAIR is configured to turn on and o with external
power. If you intend to use the RockAIR as a purely portable device, use
TP Connect to load the Portable profile to prevent transmission of position
reports while charging.
10
Adjusting LED brightness
The brightness of the LED indicators can be adjusted using the front keypad.
● Press and hold the two middle (yellow and blue) buttons until all LEDs illuminate
● Press the yellow Monitor button repeatedly to cycle through the five dierent
brightness levels
● Press any of the other three keypad buttons to choose the selected brightness. This
will become the default setting
Using Neutral Density filters
All LEDs on the RockAIR are NVG compatible with wavelengths less than 590 nanometers. In
some situations, the lowest level of brightness may still cause halo eects in NVG equipment.
Should this occur, pre-cut Neutral Density (ND) filters (included in the RockAIR kit) can be
applied by carefully removing them from the backing film and applying them over the LEDs.
ND filters can be removed and replaced at any time.
The RockAIR cannot and should not be connected to any critical-to-flight
navigation or control systems. Any independent sensors or switches
installed to support event tracking by the RockAIR must be installed in
accordance with all relevant guidelines and regulations. Specifically,
they must not present any hazard to safety of flight or compromise the
airworthiness of the aircraft.
TracPlus accepts no responsibility or liability for any damage or loss caused
by incorrect or inappropriate installation of external sensors.
11
Activating the unit
As a satellite and cellular networked device, your RockAIR needs to be activated on
these networks before it can be used; each RockAIR is shipped deactivated to prevent
unintentional reporting during delivery to the customer.
To activate your RockAIR, contact [email protected]
International roaming
The RockAIR and monthly plan includes a country-specific GPRS sim card with an appropriate
data plan suitable for most tracking and text messaging applications.
Cellular use of the RockAIR outside of your region will incur data roaming
charges that are likely to be more expensive than satellite airtime charges.
If you intend to use your RockAIR internationally, you should either turn o
cellular tracking or contact TracPlus before travel.
TracPlus is not responsible for data roaming charges incurred when using
your RockAIR while traveling internationally.
12
Basic operation
Turning RockAIR on/o
When connected to an external power source the RockAIR will turn on when power is
applied. The Power/Suspend LED indicator will turn solid to indicate that the RockAIR is
active. When external power is removed, the Power/Suspend LED indicator will turn o after a
few seconds, indicating that the RockAIR is inactive.3
When using the internal battery, turn on the RockAIR by pressing and holding the green
Power/Suspend button for two seconds. The Power/Suspend LED indicator will turn solid and
an ascending tone will sound to indicate that the unit is active. To turn o the RockAIR, press
and hold the Power/Suspend button for two seconds. The Power/Suspend LED indicator will
turn o and a descending tone will sound, indicating that the RockAIR is inactive.
When the RockAIR is turned o, it will silently attempt to transmit any queued position
reports, messages or marked points of interest for up to 15 minutes. Any unsent messages
after that time will be transmitted when the device is next turned on.
Suspending and resume tracking (Geofencing)
When working in a geographically confined area, such as an aerodrome circuit or on
agricultural operations, tracking can be suspended by pressing the green Power/Suspend
button. The Power/Suspend LED will flash to indicate that tracking is suspended.
Tracking can be resumed by pressing the Power/Suspend button or by moving beyond the
suspend auto-resume radius (which can be customized using TP Connect app). The Power/
Suspend LED will turn solid to indicate that tracking has resumed.
When suspended, no regular position reports will be transmitted regardless of cellular or
satellite coverage. Events, marked points of interest, alerts, messages, and forms will still be
transmitted using whatever coverage is available.
Automated Monitoring Service
Your RockAIR is supported by TracPlus’ Automated Monitoring Service (AMS).
When active, AMS automatically monitors the RockAIR for regular position reports and sends
notifications, via SMS should reporting stop unexpectedly.
If AMS is active, and no position reports are received within five minutes, an
Of Concern notification will be sent via SMS to your nominated In Case of Emergency
(ICE) contacts.
If no position reports are received within a further five minutes, an Overdue alert will be
treated in the same way as a Distress alert, based on your preferred Distress Notification
option (see page 21).
3 The RockAIR does not completely power down when inactive. It changes to a very low power consumption “sleep” mode using the
internal battery.
13
To request automated monitoring at the start of your flight or trip, press the yellow Monitor
button. The Monitor LED will flash quickly to indicate that monitoring has been requested.
Once monitoring has been confirmed as active, the Monitor LED will turn solid. With a good
sky view, this process should happen within a minute.
To cancel automated monitoring at the end of your flight or trip, press and hold the yellow
Monitor button for two seconds. The Monitor LED will flash slowly to indicate that monitoring
is no longer needed. Once confirmation has been received that monitoring is no longer
active, the Monitor LED will turn o. With a good sky view, this process should happen within
a minute.
If automated monitoring has been requested for a flight or trip, it is essential to cancel
monitoring at the successful conclusion of that flight or trip. If you turn o the RockAIR
without cancelling monitoring, an Of Concern and subsequent Overdue notifications will be
sent to your ICE contacts.
Of Concern and Overdue notifications will not be sent if tracking is temporarily suspended
using the Power/Suspend button. Regardless of whether tracking is suspended or not,
monitoring must still be cancelled before shutting down the RockAIR.
Marking points of interest
In addition to regular tracking, you can mark, classify and transmit a specific point of interest
using your RockAIR.
When at or overhead any point of interest, press the blue Mark button. All four button LEDs
will flash. Press any button will transmit a point of interest event that corresponds to the
button that was pressed. Dierent buttons can be mapped on request to any other event
type, such as an Ops Normal, Bucket fill, Bucket drop, and so on.
Distress alerts
Your RockAIR supports the TracPlus distress monitoring and notification service.
TracPlus provides several options for how distress alerts are notified. For details, please see
Distress Notification Options (page 21).
In an emergency (MAYDAY) or urgency (PAN-PAN) situation, pressing the red Distress/
Distress Cancel button will cause repeated distress messages to be sent to mapping
software, ICE contacts and the distress monitoring and notification service.
To enter distress mode, press the red Distress/Distress Cancel button once. The LED indicator
will flash to indicate that the RockAIR is in distress mode. While distress mode is active, the
RockAIR will transmit distress messages at a higher frequency.
To cancel distress mode, press and hold the Distress/Distress Cancel button for four seconds
until the LED indicator turns o. A Distress Cancel message will be transmitted, and normal
tracking will resume.
Monitoring should only be requested or cancelled when the RockAIR has a
good view of the sky. Do not request or cancel monitoring while the aircraft
is hangared.
14
Emergency portable use
If your RockAIR is typically connected to external power and is not modified to use external
antennas, you can use the RockAIR away from the aircraft or vehicle as required, e.g. in an
emergency.
Remove any connected cables, and remove the RockAIR from the mounting clip. The RockAIR
will shut down as the external power is removed. Press the Power/Suspend button to restart
the RockAIR using the internal battery. To activate distress mode
(if necessary), press Distress/Distress Cancel once.
Fully charged and with a good view of the sky, the RockAIR can transmit a satellite message
each minute for up to 8 hours.4 This will be aected by satellite coverage, cellular coverage,
reporting rate, connected devices, temperature, weather and other
external factors.
4 The degree of battery drain will vary depending on the transmission frequency settings of the unit. These settings can be accessed via
the TP Connect app.
If your RockAIR has been modified to use external antennas, be aware that
this will prevent emergency portable operation.
A RockAIR modified in this way will not be able to transmit or receive
messages when disconnected from those antennas, regardless of whether
powered externally or by battery.
TracPlus is not responsible for any failure of a RockAIR to operate correctly
when disconnected from external antennas.
15
Notify ICE contacts via SMS and call immediately Optional escalation to authorities‡
Distress notification options
... until acknowledged by reply SMS.
No calls are made to ICE contacts.
Reply SMS stops alerts and suspends
monitoring for 60 minutes or until
resumed earlier by reply SMS.
It is the ICE contact’s responsibility to escalate to the relevant authorities or arrange for the distress to be cancelled.
†A monthly fee per monitored device applies for Notify then Call and Notify and Call services. SMS message fees are billed separately.
‡TracPlus will only contact local authorities if a prior arrangement has been made with the customer to do so.
The customer is responsible for adding local authority escalation numbers to their ICE contacts list.
If not acknowledged by reply SMS
within five minutes ICE contacts are
called in order until answered.
If no ICE contact can be contacted,
TracPlus will escalate to authorities
as appropriate*.
If no ICE contact can be contacted,
TracPlus will escalate to authorities
as appropriate*.
Notify ICE contacts via SMS
Notify ICE contacts via SMS
A distress notification is sent via
SMS to all ICE contacts every two
minutes...
A distress notification is sent via SMS
to all ICE contacts.
A distress notification is sent via SMS to all ICE contacts.
Simultaneously, ICE contacts are called in order until answered.
Do Not Call
Call after five minutes if no reply
Do Not Escalate
Optional escalation to authorities‡
Notify Only (included with all plans)
Notify Then Call (optional service†)
Notify And Call (optional service†)
16
Advanced operation
Impact alerts
The RockAIR will transmit an impact alert if it detects a sudden impact.
The default threshold for detection and transmission of an impact alert is 16G or more for a
period of greater than 10 milliseconds. This threshold can be adjusted as necessary using the
TP Connect app.
GPS logging
The RockAIR will by default log GPS position information every second to a .gpx file on the
removable SD card. These files can be accessed by either:
Connect the RockAIR to a laptop or computer
● When the RockAIR is turned o, press and hold the yellow Monitor and blue Mark
buttons. All LEDs will light
● Press the blue Mark button once. All LEDs will flash in sequence
● Connect to your PC using the USB cable. The SD card will appear as a mounted drive
● Browse to the .gpx file of interest
● Use an online tool such as GPX Visualiser (www.gpsvisualizer.com) to connect GPX
files to Google Earth and other formats
● To disconnect, eject the mounted drive and disconnect the USB cable
Remove the MicroSD card from the RockAIR
● Remove the front silicone sleeve
● Press and remove the MicroSD card
● Insert the MicroSD card into a MicroSD card reader (not included)
● Connect the MicroSD card reader to a laptop or computer
● Browse to the .gpx file of interest
● Use an online tool such as GPX Visualiser (www.gpsvisualizer.com) to connect GPX
files to Google Earth and other formats
● To disconnect, eject the mounted drive and remove the MicroSD reader
● Remove the MicroSD card and reinsert carefully into the RockAIR
Do not remove or modify any other files on the RockAIR or MicroSD card.
17
LED light indication guide
Tracking O
Tracking Suspended
Tracking On
1. Power/Suspend
O
Flashing
On
LED Legend
Monitor O
Requesting monitoring on/o
Monitor On
2. Monitor
Device O
Battery Power
External Power
3. External Power
No device connected
n/a
Bluetooth device connected
4. Bluetooth
n/a
Waiting for confirmation
n/a
5. Mark
Normal mode
Distress mode
n/a
6. Distress/Distress Cancel
Device reset (all LEDs flash three times with chirp)
Device updating firmware (alternating flashes)
Entering MSD mode (connect to PC, press Mark)
MSD mode (press Mark then disconnect)
Combination
1 2 3 4 5 6
18
Using the RockAIR with an iOS device
Some advanced features of the RockAIR require a Bluetooth® connected iOS5 mobile
device such as an Apple® iPad®, iPad Mini® or iPhone®. These features include messaging,
configuration and forms, and require the use of TP Connect.
Downloading TP Connect
To use TP Connect, download and install it from the App Store on the device that you wish to
use with your RockAIR.
Connecting an iOS Device
To connect an iOS device with your RockAIR:
1. Enable Bluetooth on your iOS device
2. Ensure the RockAIR is turned on and within Bluetooth range (up to approximately
10 metres / 30 feet)
3. Start TP Connect
4. Tap Connect to Device
5. If presented with a list of RockAIRs, choose the RockAIR that you wish to connect to
6. If asked for a PIN number, enter 1234 and tap Unlock device
Sending and receiving messages
TP Connect can send and receive short text messages via the RockAIR via satellite and
cellular networks.
Sending messages to TracPlus
To send a text message to TracPlus users, ensure your iOS device is connected to your
RockAIR, tap on the Messages icon in TP Connect, and tap ‘TracPlus’.
Enter your message and tap Send. Your message will be transmitted and visible to any
TracPlus user that you have granted permission to see text messages from
your RockAIR.
You can receive messages sent by these users using any of the TracPlus
mapping applications.
5 TP Connect is not currently available for Android devices.
All messages sent to and from your RockAIR contribute towards your
monthly airtime usage, and may cause you to exceed your included airtime
allocation. All messages sent from your RockAIR should be as concise as
reasonably practical.
TracPlus is not responsible for airtime charges incurred in sending or
receiving messages regardless of whether they are requested, received or
wanted by the recipient.
19
Sending messages to an email address
To send a text message to an email address, ensure TP Connect is connected to your
RockAIR. Tap the Messages icon, and then tap the + icon. Choose the contact and email
address that you want to send your message to.
Enter your message and tap Send. Your message will be transmitted and delivered to that
email address. Replies from these email addresses will only be delivered if they are listed on
your TracPlus contacts address book at my.tracplus.com
Replies sent via email must be in plain text and be less than 160 characters including spaces.
Any replies larger than 160 characters, sent in HTML format, containing images or with
attachments will not be delivered.
Sending messages to a cell phone
To send a text message to a cell phone, ensure TP Connect is connected to your RockAIR.
Tap the Messages icon, and then tap the + icon. Choose the contact and cellphone that you
want to send your message to.6
Enter your message and tap Send. Your message will be transmitted and delivered to that
cellphone address.
Replies sent via SMS should be in plain text and be less than 160 characters including spaces.
Any replies larger than 160 characters, sent in MMS format, or containing images will not be
delivered.
Virtual cell numbers
Virtual cell numbers are country-specific cellular telephone numbers that are permanently
assigned to your RockAIR. This allows SMS text conversations to be originated from a cell
phone, as well as providing a reply mechanism that is more reliable and more secure than
using short codes.
Virtual cell numbers are available as an optional subscription from TracPlus, and are not
available in all countries. Please contact TracPlus for availability and pricing.
Composing and sending forms
Using TP Connect, you can compose and send forms through the RockAIR via satellite and
cellular networks.
TP Connect includes a set of basic forms appropriate to aviation use. Additional forms
including customized forms are available by contacting TracPlus.
6 Phone numbers must include a country code prefix, e.g. +64 +61 +1 etc.
Sending a message using the RockAIR and TP Connect requires a GPS fix,
and as such, you cannot send text messages from within a building, or any
other location where GPS reception is poor.
20
To complete and send a form, ensure TP Connect is connected to your RockAIR. Tap the
Forms icon, then choose the form to be sent. Complete the details in the form and press
Send. The form will be transmitted via satellite or cellular network as appropriate.
Transmitted forms are visible to TracPlus users who have permission to see forms sent from
your RockAIR.
Configuring the RockAIR
Using TP Connect, you can change the settings to control specific behavior of the RockAIR.
To configure your RockAIR, ensure your iOS device is connected to your RockAIR and press
the Configure icon in TP Connect. From the preset profiles, select Aviation, Maritime or Land.
A tick will appear to indicate the selected profile. For advanced options, contact TracPlus
Support.
If you have questions regarding any specific configuration settings, contact
Forms transmitted via satellite networks will incur additional airtime costs
depending on the size and details contained in the form, and frequency
of transmission. TracPlus is not responsible for airtime costs incurred by
transmitting forms.
Changing settings on your RockAIR can prevent the RockAIR from operating
as intended. You should only change the settings when instructed to do so
by TracPlus. TracPlus is not responsible for failures caused or airtime costs
incurred by changing the RockAIR settings away from the default settings.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Tracplus RockAIR Reliable and Affordable Aircraft Tracking Device Manuale del proprietario
- Tipo
- Manuale del proprietario
in altre lingue
Altri documenti
-
Cobra MR HH150 FLT Manuale del proprietario
-
Furuno FM4800 Manuale utente
-
ICOM IC-M127EURO Manuale del proprietario
-
-
-
Regal 29 OBX Manuale del proprietario
-
-
Raymarine Ray 201 Manuale utente
-
Risco Agility Manuale utente