Sanyo MPR-1411 Manuale utente

- 38 -- 38 -

MPR-1411

MPR-1411R

Pharmaceutical Refrigerator

INSTRUCTION MANUAL

MPR-1411R

- 39 -- 39 -

1

CONTENTS

INTRODUCTION P. 2

PRECAUTIONS FOR SAFE OPERATION P. 3

ENVIRONMENTAL CONDITIONS P. 7

REFRIGERATOR COMPONENTS P. 8

Control panel P. 10

Inside of front cover P. 11

INSTALLATION SITE P. 12

INSTALLATION P. 13

START-UP OF UNIT P. 14

STOCK OF CONTAINERS P. 15

CHAMBER TEMPERATURE SETTING P. 16

ALARM TEMPERATURE SETTING P. 17

SETTING OF DELAY OF DOOR ALARM P. 18

SETTING OF ALARM RESUME TIME P. 19

KEY LOCK FUNCTION P. 20

DEFROST CYCLES P. 21

REMOTE ALARM TERMINAL P. 21

ALARMS & SAFETY FUNCTIONS P. 22

ROUTINE MAINTENANCE

Cleaning of cabinet P. 23

Cleaning of evaporating tray P. 23

Replacement of fluorescent lamp P. 24

Replacement of glow starter P. 25

Cleaning of condenser filter P. 25

TROUBLESHOOTING P. 26

DISPOSAL OF UNIT P. 27

OPTIONAL COMPONENTS

Automatic temperature recorder P. 32

Attachment of recorder MTR-0621LH P. 32

Attachment of recorder MTR-G04A P. 33

Attachment of battery kit MPR-48B P. 35

Setting for battery before starting P. 37

SPECIFICATIONS P. 38

PERFORMANCE P. 38

SAFETY CHECK SHEET P. 39

- 40 -- 40 -

2

INTRODUCTION

Ŷ Read this manual carefully before using the appliance and follow the instructions for safety operation.

Ŷ Sanyo never guarantee any safety if the appliance is used for any objects other than intended use or

used by any procedures other than those mentioned in this manual.

Ŷ Keep this manual in an adequate place to refer to it as necessary.

Ŷ The contents of the manual will be subjected to change without notice due to the improvement of

performance or functions.

Ŷ Contact Sanyo sales representative or agent if any page of the manual is lost or page order is incorrect.

Ŷ Contact Sanyo sales representative or agent if any point in this manual is unclear or if there are any

inaccuracies.

Ŷ No part of this manual may be reproduced in any form without the expressed written permission of

Sanyo.

CAUTION

SANYO guarantees the product under certain warranty conditions. SANYO in no way shall be

responsible for any loss of content or damage of content.

- 41 -- 41 -

3

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with this manual as it contains

important safety advice.

Items and procedures are described so that you can use this unit correctly and safely.

If the precautions advised are followed, this will prevent possible injury to the user and

any other person.

Precautions are illustrated in the following way:

WARNING

Failure to observe WARNING signs could result in a hazard to personnel

possibly resulting in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbol shows;



this symbol means caution.



this symbol means an action is prohibited.



this symbol means an instruction must be followed.

Be sure to keep this manual in a place accessible to users of this unit.

< Label on the unit >

This mark is labeled on the cover in which the electrical components of high voltage

are enclosed to prevent the electric shock.

The cover should be removed by a qualified engineer or a service personnel only.

- 42 -- 42 -

4

PRECAUTIONS FOR SAFE OPERATION

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Only qualified engineers or service personnel should install the unit. The installation by

unqualified personnel may cause electric shock or fire.

Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from

turning over. If the floor is not strong enough or the installation site is not adequate, this may result

in injury from the unit falling or tipping over.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Never install the unit in a flammable or volatile location. This may cause explosion or fire.

Never install the unit where acid or corrosive gases are present as current leakage or electric

shock may result due to corrosion.

Always ground (earth) the unit to prevent electric shock. If the power supply outlet is not

grounded, it will be necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use

of any other voltage or frequency other than that on the rating label may cause fire or electric shock.

Never store volatile or flammable substances in this unit if the container cannot be sealed. These

may cause explosion or fire.

Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet on the unit.

This may cause electric shock or injury by accidental contact with moving parts.

Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use

may cause bad effect on your health or environment.

Turn off the power switch (if provided) and disconnect the power supply to the unit prior to any

repair or maintenance of the unit in order to prevent electric shock or injury.

Do not touch any electrical parts (such as power supply plug) or operate switches with a wet

hand. This may cause electric shock.

WARNING

- 43 -- 43 -

5

PRECAUTIONS FOR SAFE OPERATION

Ensure you do not inhale or consume medication or aerosols from around the unit at the time of

maintenance. These may be harmful to your health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never put containers with liquid on the unit as this may cause electric shock or short circuit when

the liquid is spilled.

Never bind, process, or step on the power supply cord, or never damage or break the power

supply plug. A broken supply cord or plug may cause fire or electric shock.

Do not use the supply cord if its plug is loose. Such supply cord may cause fire or electric shock.

Never disassemble, repair, or modify the unit yourself. Any such work carried out by an

unauthorized person may result in fire, or electric shock or injury due to a malfunction.

Disconnect the power supply plug if there is something wrong with the unit. Continued

abnormal operation may cause electric shock or fire.

When removing the plug from the power supply outlet, grip the power supply plug, not the cord.

Pulling the cord may result in electric shock or fire by short circuit.

Disconnect the power supply plug before moving the unit. Take care not to damage the power

cord. A damaged cord may cause electric shock or fire.

Disconnect the power plug when the unit is not used for long periods. Keeping the connection

may cause electric shock, current leakage, or fire due to the deterioration of insulation.

If the unit is to be stored unused in an unsupervised area for an extended period, ensure that

children do not have access and that doors cannot be closed completely.

The disposal of the unit should be accomplished by appropriate personnel. Remove doors to

prevent accidents such as suffocation.

Do not put the packing plastic bag within reach of children as suffocation may result.

WARNING

- 44 -- 44 -

6

PRECAUTIONS FOR SAFE OPERATION

Use a dedicated power source (a dedicated circuit with a breaker) as indicated on the rating label

attached to the unit. A branched circuit may cause fire resulting from abnormal heating.

Connect the power supply plug to the power source firmly after removing the dust on the plug.

A dusty plug or improper insertion may cause a heat or ignition.

Never store corrosive substances such as acid or alkali in this unit if the container cannot be

sealed. These may cause corrosion of inner components or electric parts.

Check the setting when starting up of operation after power failure or turning off of power

switch. The stored items may be damaged due to the change of setting.

Be careful not to tip over the unit during movement to prevent damage or injury.

Prepare a safety check sheet when you request any repair or maintenance for the safety of service

personnel.

CAUTION

- 45 -- 45 -

7

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions (based on the IEC 61010-1):

1. Indoor use;

2. Altitude up to 2000 m;

3. Ambient temperature 5

o

C to 40

o

C

4. Maximum relative humidity 80% for temperature up to 31

o

C decreasing linearly to 50% relative

humidity at 40

o

C;

5. Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage;

6. Other supply voltage fluctuations as stated by the manufacture;

7. Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains

supply the minimum and normal category is II;

8. Pollution degree 2 in accordance with IEC 60664.

- 46 -

8

REFRIGERATOR COMPONENTS

13

4

1

5

7

8

3

9

2

12

11 10

MPR-1411R

MPR-1411

14

15

6

Rear side

17

18

12

16

- 47 -

9

REFRIGERATOR COMPONENTS

1. Front cover: A front cover opens when a bottom part is pulled to the front. Open this cover when you

use cleaning of the condenser filter, a remote alarm terminal. Refer to page 11.

2. Control panel: Panel opens when the right top of the lower part cover is pushed. Refer to page 10.

3. Light switch: This switch is used for turning the fluorescent lamp off and on.

4. Space for temperature recorder: An temperature recorder (optional accessory) can be mounted here.

See page 32.

5. Fluorescent lamp: 40 W white lamp. See page 24 for replacement.

6. Lock: Turn the key clockwise through 180

o

to securely lock the door.

7. Glass window: The window may have condensation in high humidity environment. Wipe off the

condensation with a soft dry cloth.

8. Handle: Always hold the handle when opening/closing the door.

9. Dew receiver: The condensation on the outer door is accumulated on this dew receiver. Wipe off the

water on the dew receiver with a cloth.

10. Leveling foot: Adjust the height of the leveling feet by turning the screw bolts until the unit is level.

11. Caster: When installing the unit, the castors can be raised from the floor by using the leveling feet

above.

12. Drawer (MPR-1411R only): Items to be stored in the chamber must be placed on the drawers.

The maximum storage weight for each drawer is 40 kg.

Shelf (MPR-1411 only): Items to be stored in the chamber must be placed on the shelves. The

maximum storage weight for each shelf is 50 kg. Do not put stored items directly onto the interior floor of

the chamber. See page 15.

13. Access port: This port allows temperature measurement cables to enter the chamber from outside.

A total of three (3) ports are provided; left side, right side and top.

14. Exhaust air vent: Do not block this vent. If this vent is blocked, temperature regulation will become

unstable. Do not place stored items in the path of the cold air.

15. Intake air vent: Do not block this vent. If this vent is blocked, temperature regulation will become

unstable. Do not insert a finger or any foreign object into this vent as there is danger from the internal fan.

16. Door switch: When a door opens, a fan for the cold circulation is stopped, and the leakage of the

cold is prevented. And, the check lamp of the door is turned on.

17. Fixture: 2 fixtures are attached on the rear side of the unit. These keep adequate space between

the unit and wall and also can be used for fixing the unit. See page 13.

18. Evaporating tray: Defrost water from the evaporator accumulates on the tray and evaporates into

the atmosphere. See page 23 for cleaning.

- 48 -

10

REFRIGERATOR COMPONENTS

Control panel

1. Door check indicator (DOOR): The red LED lamp is lit when the outer door is opened.

2. Alarm lamp (ALARM): This lamp is flashed when the audible alarm is activated.

3. Digital temperature indicator: This indicator shows the present chamber temperature or set

temperature.

4. Numerical value shift key ( ): Pressing this key in the setting mode causes the numerical value to

shift. ON-OFF of key lock can be selected by pressing this key in the key lock mode.

5. Digit shift key ( ): Pressing this key in the setting mode causes the changeable digit to shift. Key

lock is available by pressing this key for more than 5 seconds in the temperature display mode. Refer to

page 20 for the key lock.

6. Set key (SET): Temperature setting mode is led by pressing this key. Once the key is pressed, the

changeable digit is flashed. Pressing this key again after setting desired temperature, the setting is

stored into computer memory. If there is no key operation for 90 seconds during the temperature setting

mode, the temperature setting mode is invalid automatically. See page 16 for the details.

7. Buzzer stop key (BUZZER): To silence the audible alarm, press this key. The remote alarm is also

silenced by pressing this key. (The buzzer cannot be stopped during remote alarm testing.)

7 6 5 4

321

- 49 -

11

REFRIGERATOR COMPONENTS

Inside of front cover

1. Condenser filter: This filter is for prevention of condenser clogged up. Clean the filter every 3

month.

2. Remote alarm terminal: This is used to connect the unit to an exterior alarm to notify users of any

malfunction. Refer to page 21.

3. Glow starter: This is for the fluorescent lamp. It is recommended that the glow starter is also

replaced when the fluorescent lamp is replaced. Refer to page 25.

4. Circuit breaker: Make sure to switch ON this breaker before starting up of the unit. This

disconnects the power when any abnormality is occurred and over current is rushed. Contact with

dealer or service station after disconnect the power supply plug. Rated AC 250 V, 10 A.

5. Fixture (rear side): 2 fixtures are attached on the rear side of the unit. These keep adequate space

between the unit and wall and also can be used for fixing the unit. See page 13.

.

1

2 5

6

3 4

- 50 -

12

INSTALLATION SITE

To operate this unit properly and to obtain maximum performance, install the unit in a location with

the following conditions:

Ŷ A location not compliance with the following conditions may cause poor performance, failure or

accident.

Ŷ A location not subjected to direct sunlight

Do not install the unit under direct sunlight. Installation in a location subjected to direct sunlight may

degrade the performance.

Ŷ A location with adequate ventilation

Leave at least 10 cm around the unit for ventilation. Poor ventilation will result in a reduction of the

performance and consequently the failure.

Ŷ A location away from heat generating sources

Avoid installing the unit near heat-emitting appliances such as a heater or a boiler etc. Heat can

decrease the intended performance of the unit.

Ŷ A location with little temperature change

Install the unit under stable ambient temperature. Installing the unit under unstable ambient temperature

may result in unstable performance.

Ŷ A location with a sturdy and level floor

Always install the unit on a sturdy and level floor withstanding the total weight of the unit. The uneven

floor or tilted installation may cause failure or injury. Unstable condition may cause vibration or noise.

Ŷ A location not prone to high humidity

Install the unit in the ambient of 80% R.H. or less humidity. Installation under high humidity may cause

current leakage or electric shock.

CAUTION

The unit may collect excessive frost on the evaporator if it is installed in high temperature and high

humidity location. This will cause frequent defrosting.

Ŷ A location without flammable or corrosive gas

Never install the unit in a flammable or volatile location. This may cause explosion or fire or may result

in the current leakage or electric shock by the corrosion of the electrical components.

CAUTION

Never install the unit in a location where the corrosive material such as sulfur compound is likely

to be generated (near a drainage facilities, etc). Corrosion of the copper pipe may result in

deterioration of cooling unit and consequently the failure.

Ŷ A location without the possibility of anything fall

Avoid installing the unit in the location where anything can fall down onto the unit. This may cause the

breakdown or failure of the unit.

- 51 -

13

INSTALLATION

1. Removing the packaging materials and tapes

Remove all transportation packaging materials and

tapes. Open the doors and ventilate the unit. If the

outside panels are dirty, clean them with a diluted

neutral dishwashing detergent. (Undiluted detergent

can damage the plastic components. For the dilution,

refer to the instruction of the detergent.) After the

cleaning with the diluted detergent, always wipe it off

with a wet cloth. Then wipe off the panels with a dry

cloth.

2. Adjusting the leveling foot

Extend the leveling feet by rotating them

counterclockwise until they make contact with the floor.

(Fig. 1) Ensure the unit is level.

3. Fixing the unit

Two fixtures are attached to the rear of the frame.

Fix the frame to the wall by attaching a rope or chain

between the wall and the fixtures.(Fig. 2)

4. Ground (earth)

The ground (earth) is for preventing the electric shock

in the case of the electrical insulation is somehow

degraded. Always ground the unit at the time of

installation.

WARNING

Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is

not grounded, it is necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Leveling foot

Fig.

Fixture

- 52 -

14

START-UP OF UNIT

Follow the procedures for the initial and consequent operations of the unit.



1. Connect the power cord to the dedicated outlet with appropriate rating.

CAUTION

If the unit is unplugged or the power to the unit is interrupted, do not restart the unit for at least 5 minutes.

This protects the compressor.

2. On start-up, the alarm buzzer sometimes operates. In this case, stop the buzzer by pressing the

alarm buzzer stop key (BUZZER).

3. Set the chamber temperature to 5

o

C.

4. Allow the chamber temperature to fall to 5

o

C. Check the chamber temperature on the temperature

indicator.

5. Turn on the fluorescent light switch to check the light. After checking, turn off the switch if the light is

not necessary.

6. Set the desired temperature. When the chamber temperature gets to the set temperature, begin

slowly placing items into the chamber to minimize the temperature rise.

CAUTION

The chamber is refrigerated by the forced circulation of cooled air inside the chamber. Ensure that the

intake and exhaust air vents are not blocked. Adequate space should be provided between the items

inside the unit to allow air circulation.

The outer door has a condensation on the glass during refrigerator operation. Wipe off the condensation

with a dry soft cloth. Also, wipe off the water on the dew receiver regularly.

- 53 -

15

STOCK OF CONTAINERS

Always distribute items so as not to disturb the air circulation in the chamber. Disruption of the

air flow can cause items to freeze or reduce the uniformity of the chamber temperature.

Never put any articles on the top of the unit.

Intake air vent

Do not block this vent with containers. If this vent

becomes blocked, temperature regulation

becomes unstable. Do not place paper or vinyl

near the vent as they may be sucked into the fan.

Exhaust air vent

Do not block this vent with containers as this can

impede air circulation. Items stored near the

exhaust air vent can freeze when the refrigerator is

operating at temperature settings lower than 5

o

C.

Load line

In this refrigerator, storage space is limited to allow

the passage of cool air around the chamber. The

label “load line” is fixed to both sides of the

chamber. Always stock items within this line.

CAUTION

Never store corrosive substances in this unit. This may lead to damage to the inner components or

electric parts.

Load line

Stock space

Side view

Cooling air

Fan

Exhaust air vent

Intake air vent

Container

- 54 -

16

CHAMBER TEMPERATURE SETTING

Table 1 shows the basic procedure for setting the chamber temperature. Perform key operations in the

sequence indicated in the table. The example in the table is based on the assumption that the desired

temperature is 10

o

C.

Note: The unit is set at the factory with a chamber temperature of 5

o

C.

Table 1 Basic operation sequence (Example: Chamber set temperature 10

o

C)

Description of operation Key operated Indication after operation

1 Connect the power supply plug. ----

The current chamber temperature is

displayed.

2 Press set key. SET

The second digit is flashed.

By pressing key, the settable digits

moves.

3

Set to 010 with the numerical value

shift key and digit shift key.

When pressed, the figure of settable

digit increases.

4 Press set key. SET

Set temperature is memorized and the

current chamber temperature is

displayed.

Note:

• The temperature set mode returns to the temperature display mode automatically when 90 seconds has

passed without any key operation. In this case, the chamber temperature setting is not accepted.

• The available set range of chamber temperature is between 2 and 23

o

C. The partial freezing may

occurred if the set temperature is lower than 3

o

C.

- 55 -

17

ALARM TEMPERATURE SETTING

This unit is provided with both high and low temperature alarms. The temperature at which the alarm is

activated may be changed.

The available set range for high temperature alarm is between +2

o

C and +14

o

C and -2

o

C and -14

o

C for

low temperature alarm against the chamber temperature.

Note: The temperature alarm is set at r5

o

C of the set temperature at the factory.

Display Mode Function

F01 High temperature alarm set See Table 2 on page 17

F02 Low temperature alarm set See Table 3 on page 17

As an example, Table 2 shows the procedure to set the high temperature alarm so that the alarm can

activate when the chamber temperature is 3

o

C higher than the set temperature.

Table 3 shows the procedure to set the low temperature alarm so that the alarm can activate when the

chamber temperature is 3

o

C lower than the set temperature.

Table 2 Procedure for setting high temperature alarm

Description of operation Key operated Indication after operation

1

---- The current chamber temperature is

displayed.

2

Press numerical value shift key for

5 seconds.

The first digit is flashed.

3

Press numerical value shift key and

scroll the figure to 6.

When pressed, the figure of settable

digit increases.

4 Press set key. SET The first digit is flashed.

Pressing the key shifts the digit which

can be set.

5

Set the temperature to 03 with the

digit shift key and numerical value

shift key.

When pressed, the figure of settable

digit increases.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

Table 3 Procedure for setting low temperature alarm

Description of operation Key operated Indication after operation

1

---- The current chamber temperature is

displayed.

2

Press numerical value shift key for

5 seconds.

The first digit is flashed.

3

Press numerical value shift key and

scroll the figure to 7.

When pressed, the figure of settable

digit increases.

4 Press set key. SET The first digit is flashed.

Pressing the key shifts the digit which

can be set.

5

Set the temperature to -03 with the

digit shift key and numerical value

shift key.

When pressed, the figure of settable

digit increases.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

- 56 -

18

SETTING OF DELAY OF DOOR ALARM

The door check indicator is light when the door is opened, and the alarm buzzer sounds with some delay

to notice the door opening.

The delay time (between lighting of the door check indicator and activation of the alarm buzzer) can be

changed. Set an appropriate delay time according to the condition of use to prevent the rise of chamber

temperature resulting from inadequate door close.

(The available set range of delay time is between 1 and 15 minutes. Initial setting (factory setting) is 2

minutes.)

Table 4 Procedure for setting of delay of door alarm (Change the delay time to 3 min. from 2

min.)

Description of operation Key operated Indication after operation

1-----

The current chamber temperature is

displayed.

2

Press numerical value shift key for

5 seconds.

F00 is displayed and the first digit

blinks.

3 Press up arrow key 4 times.

The display is changed to F04 from

F00.

4 Press set key. SET

The current setting (002) is displayed

and the first digit blinks.

5

Press numerical value shift key and

scroll the figure to 003.

The display is changed to 003 from

002.

6 Press set key. SET

Delay time is memorized and the

current chamber temperature is

displayed.

Note:

• The set mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

- 57 -

19

SETTING OF ALARM RESUME TIME

The alarm buzzer and remote alarm are silenced by pressing he alarm buzzer stop key (BUZZER) on the

control panel during alarm condition. The buzzer and remote alarm will be activated again after certain

suspension if the alarm condition is continued. The suspension time can be set by following the

procedure shown in the Table 5 below.

The example in the table is based on the assumption that the desired duration is 20 minutes.

Note: The duration is set in 30 minutes at the factory.

Table 5 Procedure for setting of alarm resume time (Example: change from 30 minutes to 20

minutes)

Operation Key operated Indication after operation

1-----

The current chamber temperature

is displayed.

2

Press and hold the numerical value

shift key for about 5 seconds.

The first digit of the temperature

display blinks.

Pressing the key leads the change of flashed

digit.

3

Set to F25 by using digit shift key

and numerical value shift key.

Pressing the key shifts up the figure

of the current digit.

4 Press the set key. SET

The current set value is displayed and

the second digit of the temperature

display flashes.

5

Set to 020 by using numerical value

shift key.

Pressing the key shifts up the figure in

the second digit.

6 Press the set key. SET

The value is stored in memory and

the current chamber temperature is

displayed.

Note:

• The settable alarm resume times are 10, 20, 30, 40, 50, or 60 minutes (The set values are 010, 020,

030, 040, 050, and 060). The buzzer would not reset if the resume time is set in 000.

• The set mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

La pagina sta caricando ...

Sanyo MPR-1411 Manuale utente

Questo manuale è adatto anche per

Sanyo MPR-1411 Manuale utente

in altre lingue

Documenti correlati

Altri documenti