Pioneer X-HM26D Manuale utente

Для моделей

X-HM16/X-HM26

Дополнительная информация для клиентов в

Российской Федерации Информация о сертификации

X-HM16

X-HM26

X-HM26D

CD Receiver System

Micro chaîne CD

Sistema receptor de CD

Sistema CD con amplificatore

CD-Receiversystem

CD Receiver System

Система ресивера CD

Operating Instructions

Mode d’emploi

Manual de instrucciones

Istruzioni per l’uso

Bedienungsanleitung

Handleiding

Инструкции по эксплуатации

Register your product on/ Enregistrez votre produit sur / Registre su producto en

Registrare il proprio prodotto su / Registrieren Sie hier Ihr Produkt /

Registreer uw product op / Зарегистрируйте ваше изделие

http://www.pioneer.eu

(Europe / Europe / Europa / Europa / Europa / Europa / Европа)

SN29402699_X-HM16_26_26D_En_European.book 1 ページ２０１６年７月２２日　金曜日　午後７時２分

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight

(or strong artificial light)

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which

requires repair will be charged for even during the

warranty period.

K041_A1_En

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 25 cm at top, 10 cm at rear, and 5 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that

they are not likely to be stepped on. A damaged power

cord can cause a fire or give you an electrical shock.

Check the power cord once in a while. When you find

it damaged, ask your nearest our authorized service

center or your dealer for a replacement.

S002*_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from

the AC outlet to shut down all power. Therefore,

make sure the unit has been installed so that the

power cord can be easily unplugged from the AC

outlet in case of an accident. To avoid fire hazard,

the power cord should also be unplugged from the

AC outlet when left unused for a long period of time

(for example, when on vacation).

D3-4-2-2-2a*_A1_En

SN29402699_X-HM16_26_26D_En_European.book 2 ページ２０１６年７月２２日　金曜日　午後７時２分

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which

is a band used by other wireless systems (Microwave

ovens and Cordless phones, etc.). In this event noise

appears in your television image, there is the

possibility this unit (including products supported by

this unit) is causing signal interference with the

antenna input connector of your television, video,

satellite tuner, etc. In this event, increase the distance

between the antenna input connector and this unit

(including products supported by this unit).

• We are not responsible for any malfunction of the

compatible product due to communication

error/malfunctions associated with your network

connection and/or your connected equipment.

Please contact your Internet service provider or

network device manufacturer.

• A separate contract with/payment to an Internet

service provider is required to use the Internet.

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

SN29402699_X-HM16_26_26D_En_European.book 3 ページ２０１６年７月２２日　金曜日　午後７時２分

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you

have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Loading the batteries in the remote control . . . . . . . . . . . .5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . 5

02 Part names and functions

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

03 Connections

Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Using external antennas . . . . . . . . . . . . . . . . . . . . . . 10

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

04 Getting started

To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Input function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display brightness control . . . . . . . . . . . . . . . . . . . . . 12

Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

P.BASS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

BASS/TREBLE control. . . . . . . . . . . . . . . . . . . . . . . . 13

Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . .13

Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . 14

Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . 14

Using the wake-up timer . . . . . . . . . . . . . . . . . . . . . . 14

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

05 Disc playback

Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Load the disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Play tracks on a CD . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Play MP3 music files . . . . . . . . . . . . . . . . . . . . . . . . . 15

Advanced CD or MP3 disc playback . . . . . . . . . . . . . . . .16

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Programmed play (CD) . . . . . . . . . . . . . . . . . . . . . . . 17

About downloading MP3 . . . . . . . . . . . . . . . . . . . . . . 17

Switch the display contents . . . . . . . . . . . . . . . . . . . . 17

06 USB playback

Playing USB storage devices . . . . . . . . . . . . . . . . . . . . .18

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Switch the display contents . . . . . . . . . . . . . . . . . . . . 19

07 Using the tuner

Listening to FM (For European models)/Listening to FM or

AM (For North American models) . . . . . . . . . . . . . . . . . . 20

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the Radio Data System (RDS)

(for European models only) . . . . . . . . . . . . . . . . . . . . 21

Listening to the DAB+ (X-HM26D only) . . . . . . . . . . . . . 23

About DAB+ (Digital Audio Broadcasting) . . . . . . . . . 23

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Changing the information display . . . . . . . . . . . . . . . . 24

Memorising a station. . . . . . . . . . . . . . . . . . . . . . . . . . 24

DAB Frequency table (BAND III) . . . . . . . . . . . . . . . . 24

08 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . . . 25

Automatic switching to Audio In input (For North American

models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

09 Bluetooth

®

Audio playback

Music playback using Bluetooth wireless technology . . . 26

Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . 26

Pairing with the unit (Initial registration) . . . . . . . . . . . . . 26

Listen to music on the unit

from a Bluetooth capable device

. . . . . . . . . . . . . . . . . . . . 27

BT STANDBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Radio wave caution. . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Precautions regarding connections

to products supported by this unit

. . . . . . . . . . . . . . . . . 28

10 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Playable discs and formats . . . . . . . . . . . . . . . . . . . . . . . 31

Regarding copy protected CDs. . . . . . . . . . . . . . . . . . 32

Supported audio file formats. . . . . . . . . . . . . . . . . . . . 32

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

When moving this unit. . . . . . . . . . . . . . . . . . . . . . . . . 32

Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Do not place objects on this unit. . . . . . . . . . . . . . . . . 32

About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Storing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

About specially shaped discs . . . . . . . . . . . . . . . . . . . 33

Auto power off setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Restoring all the settings to the defaults . . . . . . . . . . . . . 33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

SN29402699_X-HM16_26_26D_En_European.book 4 ページ２０１６年７月２２日　金曜日　午後７時２分

Before you start 01

5

En

English

Français Español

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box

when you open it.

• Remote Control

• AAA batteries (R03) x 2

• Power cord

• AM antenna cable*1

• FM wire antenna*2

• DAB/FM wire antenna*3

• Warranty card*4

• Operating instructions (this document)

*1 North American models only

*2 X-HM16/X-HM26 only

*3 X-HM26D only

*4 European models only

Loading the batteries in the remote

control

1 Open the rear lid and load the batteries as

illustrated below.

2 Close the rear lid.

CAUTION

• Do not use any batteries other than the ones specified.

Also, do not use a new battery together with an old one.

• When inserting the batteries, make sure not to damage

the springs on the battery’s - terminals. This can

cause batteries to leak or over heat.

• When loading the batteries into the remote control, set

them in the proper direction, as indicated by the polarity

marks (+ and -).

• Do not heat batteries, disassemble them, or throw them

into flames or water.

• Batteries may have different voltages, even if they are

the same size and shape. Do not use different types of

batteries together.

• To prevent leakage of battery fluid, remove the

batteries if you do not plan to use the remote control for

a long period of time (1 month or more). If the fluid

should leak, wipe it carefully off the inside of the case,

then insert new batteries. If a battery should leak and

the fluid should get on your skin, flush it off with large

quantities of water.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

WARNING

• Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the life or

performance of batteries.

Using the remote control

The remote has a range of about 7 m at an angle of about

30º from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can interfere

with each other. Avoid using remotes for other

equipment located close to this unit.

• Replace the batteries when you notice a fall off in the

operating range of the remote.

I

NPU

T

30°

7 m

30°

SN29402699_X-HM16_26_26D_En_European.book 5 ページ２０１６年７月２２日　金曜日　午後７時２分

Part names and functions02

6

En

Chapter 2:

Part names and functions

Remote control

1 Í

Switches the receiver between standby and on (page 12).

2 Input function buttons

Use to select the input source to this receiver (page 12).

Use to set up or play the audio file using the Bluetooth

network (page 26).

3MENU

Use to access the menu.

4



/



/



/



, ENTER

Use to select/switch system settings and modes, and to

confirm actions.

5 PGM/MEMORY

• Use to memory or program the CD (page 17).

• Use to store FM/AM (page 20) or DAB (page 24)

stations in memory.

6 Playback control buttons

Use to control each function after you have selected it using

the input function buttons (page 16).

TUNE +/–

Use to find radio frequencies (page 20).

PRESET +/–

Use to select preset radio stations (page 20).

7 Sound control buttons

Adjust the sound quality (page 13).

8SLEEP

See Using the sleep timer on page 14.

9TIMER

Use for setting the clock, as well as for setting and checking

the timers (page 12).

10

Press to change the repeat play setting from a CD (page 16)

or USB (page 19).

11 RANDOM

Press to randomize order play setting from a CD (page 16)

or USB (page 19).

12 DISPLAY

Press to change the display for MP3 (page 17), RDS

(page 21) or DAB (page 24) information.

13

Press to return to the previous display.

14 Volume control buttons

Use to set the listening volume (page 12).

15

Mutes/unmutes the sound (page 12).

16 DIMMER

Dims or brightens the display. The brightness can be

controlled in four steps (page 12).

1

2

3

6

4

7

8

9

5

11

12

13

14

10

15

16

SN29402699_X-HM16_26_26D_En_European.book 6 ページ２０１６年７月２２日　金曜日　午後７時２分

Part names and functions 02

7

En

English

Français Español

Front panel

1

Í

STANDBY/ON

Switches the receiver between standby and on (page 12).

2 Remote sensor

Receives the signals from the remote control.

3 TIMER indicator

Lights when the receiver is power off with timer setting.

4 Main display

See Display on page 8.

5 Volume control

Use to set the listening volume (page 12).

6INPUT

Selects the input source.

7 Headphone socket

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers.

8USB terminal

Use to connect your USB mass storage device as an audio

source (page 18).

9 Disc tray

Place the disc, label side up (page 15).

10 Playback control buttons

Selects the desired track or file to be played back. Use to

stop the playback. Stops playback or resumes playback from

the pause point.

11 Disc tray open/close button

Use to open or close the disc tray (page 15).

TIMER

1 3 4 52

76 8 9 10 11

SN29402699_X-HM16_26_26D_En_European.book 7 ページ２０１６年７月２２日　金曜日　午後７時２分

Part names and functions02

8

En

Display

1

Lights when the sound is muted.

Note

• The mute icon will be displayed in red.

2

1

Start playback.

3

;

Pause playback.

4

Timer function is set.

5 Character display

Displays various system information.

Speaker system

1 Tweeter

2 Woofer

3 Bass Reflex Duct

Important

• Speaker grille cannot be removed.

• Both speakers can be used on either the right or the left

side.



11234

5

1

2

3

SN29402699_X-HM16_26_26D_En_European.book 8 ページ２０１６年７月２２日　金曜日　午後７時２分

Connections 03

9

En

English

Français Español

Chapter 3:

Connections

CAUTION

• Be sure to turn off the power and unplug the power cord

from the power outlet whenever making or changing

connections.

• Connect the power cord after all the connections

between devices have been completed.

Speaker connection

• Push open the tabs and insert exposed wire.

• Connect the black wire to (s) terminal, and the red wire

to the (r) terminal.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Do not connect any speakers other than those

supplied to this system.

• Do not connect the supplied speakers to any amplifier

other than the one supplied with this system.

Connection to any other amplifier may result in

malfunction or fire.

• Do not attach these speakers to the wall or ceiling.

They may fall off and cause injury.

• These speakers are magnetically shielded. However,

depending on the installation location, color distortion

may occur if the speaker system is installed extremely

close to the screen of a television set. If this happens,

turn off the television set, and then turn it on after 15 to

30 minutes. If the problem persists, move the speaker

system away from the television set.

• Make sure that the speaker cable cores do not become

exposed and make contact with other cable cores. This

may cause malfunction of the product.

• Do not allow the speaker cable core to come into

contact with the receiver body.

• If the speaker cable core comes into contact with any

metal portion of the receiver’s body, it may damage the

speakers and cause smoke and fire.

Insert speaker cables securely into the terminals and

check that the cable does not come out of easily.

Note

• There is no difference between L and R speakers.

Left

speaker

Right

speaker

This unit’s rear panel

SN29402699_X-HM16_26_26D_En_European.book 9 ページ２０１６年７月２２日　金曜日　午後７時２分

Connections03

10

En

Connecting antennas

• Connect the AM loop antenna and the FM (DAB/FM)

wire antenna as shown below.

• To improve reception and sound quality, connect

external antennas (see Using external antennas).

For North American models only

For European models

1 Connect the AM antenna wires.

Holding the connector to connect.

2 Fix the AM loop antenna to the attached

stand.

Set up as illustrated above.

3 Place the AM antenna on a flat surface and

in a direction giving the best reception.

• Place the antenna near a window, etc. for the best

reception.

• Do not place the antenna near a computer or TV. It may

result in noise.

4 Connect the FM (DAB/FM) wire antenna into

the FM antenna socket.

For best results, extend the FM (DAB/FM) antenna fully and

fix to a wall or door frame. Don’t drape loosely or leave coiled

up.

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an external

FM (DAB/FM) antenna.

2

1

3

4

1

2

3

X-HM16/X-HM26

X-HM26D

4

X-HM16/

X-HM26

X-HM26D

One-touch PAL

connector

75 coaxial

cable

SN29402699_X-HM16_26_26D_En_European.book 10 ページ２０１６年７月２２日　金曜日　午後７時２分

Connections 03

11

En

English

Français Español

Plugging in

Before making or changing the connections, switch off the

power and disconnect the power cord from the AC outlet.

After you’ve finished making all connections, plug the unit

into an AC outlet.

CAUTION

• Do not use any power cord other than the one supplied

with this unit.

• Do not use the supplied power cord for any purpose

other than that described above.

To AC outlet

This unit’s rear panel

Power cord

SN29402699_X-HM16_26_26D_En_European.book 11 ページ２０１６年７月２２日　金曜日　午後７時２分

Getting started04

12

En

Chapter 4:

Getting started

To turn the power on

Press the Í to turn the power on.

After use:

Press the Í to enter the power stand-by mode.

Setting the clock

1 Press

Í

to turn the power on.

2 Press TIMER on the remote control.

“CLOCK” is shown on the main display.

3 Press ENTER.

4 Press



/



to set the day, then press

ENTER.

5 Press



/



to set the hour, then press

ENTER.

6 Press



/



to set the minute, then press

ENTER to confirm.

7 Press ENTER.

To confirm the time display:

Press the TIMER. The time display will appear for about 10

seconds.

To readjust the clock:

Perform “Setting the clock” from step 1.

Note

• When power supply is restored after unit is plugged in

again or after a power failure, reset the clock.

General control

Input function

When the INPUT on main unit is pressed, the current

function will change to different mode. Press the INPUT

repeatedly to select desired function.

*1 X-HM26D only

*2 North American models only

Display brightness control

Press DIMMER to dims the display brightness. The

brightness can be controlled in four steps.

Volume auto set-in

If you turn off and on the main unit with the volume set to 31

or higher, the volume starts at 30 and sets in to the last set

level.

Volume control

Turn the volume knob towards VOLUME (on main unit) or

press VOL +/– (on remote control) to increase or decrease

the volume.

CAUTION

• The sound level at a given volume setting depends on

speaker efficiency, location, and various other factors.

It is advisable to avoid exposure to high volume levels.

Do not turn the volume on to full at switch on. Listen to

music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

Muting

The volume is muted temporarily when pressing the on

the remote control. Press again to restore the volume.

CD

Bluetooth DAB

1

*

2

*

AM

A

udio In FMUSB

SN29402699_X-HM16_26_26D_En_European.book 12 ページ２０１６年７月２２日　金曜日　午後７時２分

Getting started 04

13

En

English

Français Español

Sound controls

Equalizer

When the EQ is pressed, the current mode setting will be

displayed. To change to a different mode, press the EQ

repeatedly until the desired sound mode appears.

P.BASS control

When the power is first turned on, the unit will enter the

P.bass mode which emphasises the bass frequencies. To

cancel the P.bass mode, press the P.BASS on the remote

control.

BASS/TREBLE control

Press the SOUND to select “BASS” or “TREBLE”, then

press



/



to adjust the bass or treble.

Note

• The EQ and P.BASS cannot operate simultaneously.

The most recently selected of these two functions will

be the one used.

• SOUND can operate alongside either the EQ or

P.BASS.

When one of the above two functions is selected,

the function that is not selected will be displayed

as follows.

1 When P.BASS setting (ON/OFF) is changed

• EQ : FLAT

2 When EQ setting is changed

• P.BASS : OFF

Setting the wake-up timer

Used to change the existing timer setting, or to set a new

timer.

1 Press

Í

to turn the power on.

2 Press and hold TIMER on the remote

control.

3 Press



/



to select “ONCE” or “DAILY”,

then press ENTER.

ONCE – Once timer play works for one time only at a

preset time.

DAILY – Daily timer play works at the same preset time

and days of week.

4 Press



/



to select “TIMER SET”, then

press ENTER.

5 Press



/



to select the timer playback

source, then press ENTER.

CD, DAB (X-HM26D only), FM, AM (North American models

only) and USB can be selected as the playback source.

6 Press



/



to select the timer day, then

press ENTER.

7 Press



/



to set the hour, then press

ENTER.

8 Press



/



to set the minute, then press

ENTER.

Set the time to finish as in steps 7 and 8 above.

9 Adjust the volume press VOL +/– , then

press ENTER.

“ ” appears on the display.

10 Press

Í

to enter the power standby mode.

The TIMER indicator lights up.

NIGHT

FLAT A flat and basic sound

ACTIVE

DIALOGUE

A sound that can be enjoyed

at night even with lower volume

A powerful sound that

emphasizes low and high tones

A sound that allows the radio or

vocals to be heard more easily

SN29402699_X-HM16_26_26D_En_European.book 13 ページ２０１６年７月２２日　金曜日　午後７時２分

Getting started04

14

En

Calling the wake-up timer

It can be used to re-use an existing timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press



/



to select “TIMER ON”, then

press ENTER.

Cancelling the wake-up timer

It can be used to turn off the timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press



/



to select “TIMER OFF”, then

press ENTER.

Using the wake-up timer

1 Press

Í

to turn the power off.

2 At the wake-up time, this unit will turn on

automatically and play the selected input

function.

Note

• If at the wake-up time the USB storage device is not

connected to this unit or a disc is not inserted, this unit

will be turned to on and not play back the track.

• Some discs may not be played automatically at the

wake-up time.

• If you set the timer, take one minute or more between

the start and end time.

Using the sleep timer

The sleep timer switches off the unit after a specified time so

you can fall asleep without worrying about it.

1 Press SLEEP repeatedly to select a switch

off time.

Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120

min, 150 min, 180 min or OFF. The newly set value displays

for 3 seconds, and then the setting is completed.

Note

• The sleep timer can be set by pressing SLEEP while

the remaining time is displayed.

Using Headphones

Connect to the jack plug of the headphones.

When the headphones are connected, there is no sound

output from the speakers.

• Do not turn the volume on to full at switch on and listen

to music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

• Before plugging in or unplugging the headphone,

reduce the volume.

• Be sure your headphone has a 3.5 mm diameter plug

and impedance between 16

 and 50 . The

recommended impedance is 32

.

TIMER

SN29402699_X-HM16_26_26D_En_European.book 14 ページ２０１６年７月２２日　金曜日　午後７時２分

Disc playback 05

15

En

English

Français Español

Chapter 5:

Disc playback

This system can play back a standard CD, CD-R/RW in the

CD format and CD-R/RW with MP3 files, but cannot record

on them. Some audio CD-R and CD-RW discs may not be

playable due to the state of the disc or the device that was

used for recording.

• For details about MP3, see page 31.

Playing discs or files

Load the disc

1 Press

Í

to turn the power on.

2 Press CD on the remote control or INPUT

repeatedly on the main unit to select CD input.

3 Press

<

on the main unit to open the disc tray.

4 Place the disc on the disc tray, label side up.

5 Press

<

on the main unit to close the disc

tray.

Play tracks on a CD

1 When the recognition is completed, press

1;

.

After the last track is played, the unit will stop automatically.

Play MP3 music files

MP3 track data is called “music file” and the location they are

stored is called a “folder” in this document.

1 When the recognition is completed, press



/



to select the folder where the music file is

stored ([ ]), then press



or ENTER.

• Repeat this step if there are other folders inside the

selected folder.

• To return to the previous folder, press



or .

2 Press



/



to select the music file ([ ]), and

then press

1;

or ENTER.

• Once play starts, only music files inside the same folder

can be played continuously.

CAUTION

• Do not place two discs in one disc tray.

• Do not play discs of special shapes (heart, octagon,

etc). It may cause malfunctions.

• Do not push the disc tray whilst it is moving.

• If the power fails whilst the tray is open, wait until the

power is restored.

• Be sure to place 8 cm disc in the middle of the disc tray.

Note

• Due to the structure of the disc information, it takes

longer to read an MP3 disc than a normal CD

(approximately 20 to 90 seconds).

• When the beginning of the first track is reached during

fast reverse, the unit will enter the playback mode (only

for CD).

• If TV or radio interference occurs during CD operation,

move the unit away from the TV or radio.

Tip

• When no operation has done in CD mode and the audio

file is not played for more than 20 minutes, the power

will automatically turn off. In this case it is required that

the Auto power off is switched to ON.

• Auto power off can be switched to ON/OFF (page 33).

e.g.,

SN29402699_X-HM16_26_26D_En_European.book 15 ページ２０１６年７月２２日　金曜日　午後７時２分

Disc playback05

16

En

Basic operations

Advanced CD or MP3 disc playback

Repeat play

Repeat play can play one track, all tracks or a programmed

sequence continuously.

To repeat one track:

Press repeatedly until “REPEAT ONE” appears. Press

ENTER.

To repeat all tracks:

Press repeatedly until “REPEAT ALL” appears. Press

ENTER.

To repeat desired tracks:

Perform steps 1 - 5 in “Programmed play (CD)” section

(page 17) and then press repeatedly until “REPEAT

ALL” appears. Press ENTER.

To cancel repeat play:

Press repeatedly until “REPEAT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press ∫.

Otherwise, the disc will play continuously.

• During repeat play, random play is not possible.

Random play

The tracks on the disc can be played in random order

automatically.

To random play all tracks:

Press RANDOM repeatedly until “RANDOM ON” appears.

Press ENTER.

To cancel random play:

Press RANDOM repeatedly until “RANDOM OFF” appears.

Press ENTER.

Note

• If you press the 9 during random play, you can move

to the track selected next by the random operation.

• In random play, the unit will select and play tracks

automatically. (You cannot select the order of the

tracks.)

• During random play, repeat play is not possible.

Function Main unit Remote

control

Operation

Play

Press in the stop mode.

Stop

Press in the playback

mode.

(when playing a CD)

“RESUME” is

displayed and the

place where you

stopped play is

memorized. Press

again and the

memorized position

is cleared.

Pause

Press in the playback

mode. Press

1;

to

resume playback from

the paused point.

Track up/

down

Press in the playback

or stop mode.

If you press the button

in the stop mode, press

1;

to start the desired

track.

(when playing MP3)

You can only skip

forward or back to

music files inside the

same folder.

Fast

forward/

reverse

Press and hold down in

the playback mode.

Release the button to

resume playback.

SN29402699_X-HM16_26_26D_En_European.book 16 ページ２０１６年７月２２日　金曜日　午後７時２分

Disc playback 05

17

En

English

Français Español

Programmed play (CD)

You can choose up to 24 selections for playback in the order

you like.

1 Whilst in the stop mode, press PGM/

MEMORY on the remote control to enter the

programming save mode.

2 Press

:

9

to select the desired tracks.

3 Press ENTER to save track number.

4 Repeat steps 2 - 3 for other tracks. Up to 24

tracks can be programmed.

• If you want to check the programmed tracks, press

PGM/MEMORY.

• If you make a mistake, the last programmed tracks will

be canceled by pressing .

5 Press

1;

to start playback.

To cancel the programmed play mode:

To cancel the programmed play, press twice ∫ on the

remote control. The display will show “PRG CLEAR” and all

the programmed contents will be cleared.

Adding tracks to the program:

Press the PGM/MEMORY. Then follow steps 2 - 3 to add

tracks.

Note

• When a disc is ejected, the program is automatically

cancelled.

• If you press the Í to enter the standby mode or change

the function from CD to another, the programmed

selections will be cleared.

• During the program operation, random play is not

possible.

About downloading MP3

There are many music sites on the internet that you can

download MP3 music files. Follow the instructions from the

website on how to download the music files. You can then

play back these downloaded music files by burning them to

a CD-R/RW disc.

• Your downloaded song/files are for personal use only.

Any other usage of the song without owner’s

permission, is against the law.

Switch the display contents

1 Press DISPLAY during playback.

If the title, artist and album name has been written to the file,

that information will be displayed. (You can view this unit is

only alphanumeric characters. Non- alphanumeric character

are displayed in the “∫”.)

Note

• “Not supported playback file” can not be playback. In

this case, will be skipped automatically.

• There may be cases where no information can be

displayed.

• Displaying title, artist, and albums is only supported with

ID3 Version 1 (1.0 or 1.1).

Title display

Number of the track, title

display

Artist display

Album display

Number of the track in

a folder, playback time

display

Number of the track in a

folder, remaining time

display

SN29402699_X-HM16_26_26D_En_European.book 17 ページ２０１６年７月２２日　金曜日　午後７時２分

USB playback06

18

En

Chapter 6:

USB playback

Playing USB storage devices

It is possible to listen to two-channel audio using the USB

interface with MP3 files on the front of this receiver.

• Pioneer does not guarantee that any file recorded on a

USB storage device will play or that power will be supplied

to a USB storage device. Also note that Pioneer will accept

no responsibility whatsoever for loss of files on USB

storage devices caused by connection to this unit.

• For details about MP3, see page 31.

1 Press USB as the input source.

“USB” is shown on the main display.

2 Connect the USB storage device.

• This receiver does not support a USB hub.

3 When the recognition is completed, press



/



to select the folder where the music file is

stored ([ ]), then press



or ENTER.

• MP3 track data is called “music file” and the location

they are stored is called a “folder” in this document.

• Repeat this step if there are other folders inside the

selected folder.

• To return to the previous folder, press



or .

4 Press



/



to select the music file ([ ]), and

then press

1;

or ENTER.

• Once play starts, only music files inside the same folder

can be played continuously.

• For details about the basic operations, see page 16.

• When changing to a different input source, stop the

USB memory playback first, before changing.

• Turn the power off before removing the USB storage device.

Note

• This unit may not recognize a USB storage device, play files

or supply power to a USB storage device. For details, see

When a USB storage device is connected

on page 30.

• When a USB storage device is not playing and the unit has

not been operated for 20 minutes or more, the power will

automatically turn off. In this case it is required that the

Auto power off is switched to

ON

(page 33).

TIMER

USB storage device

(commercially available)

SN29402699_X-HM16_26_26D_En_European.book 18 ページ２０１６年７月２２日　金曜日　午後７時２分

USB playback 06

19

En

English

Français Español

Repeat play

Repeat play can play one track, all tracks or a programmed

sequence continuously.

To repeat one track:

Press repeatedly until “REPEAT ONE” appears. Press

ENTER.

To repeat all tracks:

Press repeatedly until “REPEAT ALL” appears. Press

ENTER.

To cancel repeat play:

Press repeatedly until “REPEAT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press

∫

. Otherwise,

the file of USB storage device will play continuously.

• During repeat play, random play is not possible.

Random play

The file of USB storage device can be played in random

order automatically.

To random play all tracks:

Press RANDOM repeatedly until “RANDOM ON” appears.

Press ENTER.

To cancel random play:

Press RANDOM repeatedly until “RANDOM OFF” appears.

Press ENTER.

Note

• If you press the 9 during random play, you can move

to the track selected next by the random operation.

• In random play, the unit will select and play tracks

automatically. (You cannot select the order of the tracks.)

• During random play, repeat play is not possible.

Switch the display contents

This unit can switch the information recorded in the USB

storage device. For details, see Switch the display contents

on page 17.

SN29402699_X-HM16_26_26D_En_European.book 19 ページ２０１６年７月２２日　金曜日　午後７時２分

Using the tuner07

20

En

Chapter 7:

Using the tuner

Listening to FM (For European

models)/Listening to FM or AM (For

North American models)

The following steps show you how to tune in to FM and AM

radio broadcasts using the automatic (search) and manual

(step) tuning functions. Once you are tuned to a station you

can memorize the frequency for recall later. See Saving

station presets below for more on how to do this.

Tuning

1 Press the

Í

to turn the power on.

2 Press TUNER repeatedly to select desired

frequency band (FM or AM).

• (X-HM26D) You can select “FM” and “DAB”.

For details about “DAB”, see page 23.

3 Press TUNE +/– on the remote control to

tune in to the desired station.

Automatic tuning:

Press and hold TUNE +/–, scanning will start automatically

and the tuner will stop at the first receivable broadcast

station.

Manual tuning:

Press the TUNE +/– repeatedly to tune in to the desired

station.

Note

• When radio interference occurs, automatic tuning may

stop automatically at that point.

• Automatic tuning will skip weak signal stations.

• To stop the automatic tuning, press ∫.

• When an RDS (Radio Data System) station is tuned in,

the frequency will be displayed first. Finally, the station

name will appear.

• Full auto tuning can be achieved for RDS stations using Auto

Station Program Memory (ASPM) mode, see page 22.

To receive an FM stereo transmission:

1 Press TUNER until “FM” appears on the display.

2 Press MENU and then press / until “FM STEREO/

MONO” appears on the display.

3 Press ENTER and then press / until “AUTO”

appears on the display.

Improving poor FM reception:

After performing the above steps 1 - 2, press ENTER and

then press / until “MONO” appears on the display.

This will change the tuner from stereo to mono and usually

improve the reception.

Saving station presets

If you often listen to a particular radio station, it’s convenient

to have the receiver store the frequency for easy recall

whenever you want to listen to that station (Preset tuning).

This saves the effort of manually tuning in each time. This

unit can memorize up to 45 stations.

(FM 30 stations/AM 15 stations)

1 Tune to a station you want to memorize.

See Tuning above for more on this.

2 Press PGM/MEMORY.

The preset number will flash.

3 Press PRESET +/– to select the preset

channel number.

4 Press PGM/MEMORY to store that station

in memory.

If the preset number has changed from flashing to lighting,

before the station is memorised, repeat the operation from

step 2.

• Repeat steps 1 - 4 to set other stations, or to change a

preset station. When a new station is stored in the

memory, the station previously memorised for that

preset channel number will be erased.

SN29402699_X-HM16_26_26D_En_European.book 20 ページ２０１６年７月２２日　金曜日　午後７時２分

La pagina sta caricando ...

Pioneer X-HM26D Manuale utente

Questo manuale è adatto anche per

Pioneer X-HM26D Manuale utente

in altre lingue

Documenti correlati

Altri documenti