Ruckus Wireless ZoneFlex 2741 Manuale utente

Ruckus Wireless

®

ZoneFlex

®

2741 802.11g

Outdoor Access Point

Getting Started Guide

www.ruckuswireless.com

1

1 About This Getting Started Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Using ZoneDirector or FlexMaster to Manage the Access Point . . . . . . . . . . . . . . . . . . 1

2 Unpacking the ZoneFlex Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Bottom Cover and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Prepare the Required Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Get to Know the Access Point Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LED Colors and What They Mean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Perform a Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Determine the Optimal Mounting Location and Orientation . . . . . . . . . . . . . . . . . . . . . 9

Become Familiar with the Installation Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Configuring the Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Configuring for Management by ZoneDirector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Configuring for Standalone Operation or for Management by FlexMaster . . . . . . . . 14

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 1: Prepare the Administrative Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 2: Connect the Access Point to the Administrative Computer . . . . . . . . . . . . . 16

Step 3: Log Into the Access Point’s Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Step 4: Configure the Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 5: Disconnect the Access Point from the Administrative Computer . . . . . . . . . 23

Step 6: Restore the Administrative Computer’s Network Settings . . . . . . . . . . . . . . 23

5 Attaching the Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Contents

2

Step 1: Attach the Static Bracket to the Mounting Surface . . . . . . . . . . . . . . . . . . . . . 26

Attaching the Bracket to a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Attaching the Bracket to a Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Step 2: Attach the Dynamic Bracket to the Access Point . . . . . . . . . . . . . . . . . . . . . . . 31

Mounting on a Flat Surface or Vertical Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Mounting on a Horizontal Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6 Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7 Verifying the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Associate a Wireless Client with the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Check the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Check the TR069 Status (FlexMaster Management Only) . . . . . . . . . . . . . . . . . . . . . . . 41

8 Joining the Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Mounting on a Flat Surface or Vertical Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Mounting on a Horizontal Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

9 (Optional) Mounting and Connecting the External Antenna . . . . . . . . . . . . . . . . . . . . . . 46

10 What to Do Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Change the Administrative Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Configure the Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Read Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

11 Professional Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Personal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

External Entenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

1

1 About This Getting Started Guide

This Getting Started Guide provides information on how to set up the Ruckus Wireless

ZoneFlex 2741 802.11g Outdoor Access Point on your network. Topics covered in this

guide include installation, basic configuration, and device mounting.

This guide is intended for use by those responsible for installing and setting up network

equipment. Consequently, it assumes a basic working knowledge of local area networking,

wireless networking, and wireless devices.

Related Documentation

In addition to this guide, each Ruckus Wireless ZoneFlex 2741 802.11g Outdoor Access

Point documentation set includes the following:

■ User Guide: Provides detailed information on how to configure the Access Point. The

User Guide is available for download on the Ruckus Wireless Support Web site at:

http://support.ruckuswireless.com/documents

■ Release Notes: Provides late-breaking information about the current software release,

including new features, enhancements, and known issues. If the information in the

Release Notes differs from the information in this guide, follow the instructions in the

Release Notes.

■ Online Help: Accessible from the ZoneFlex Web interface, the Online Help provides

information that helps you configure the Access Point using the Web interface.

Using ZoneDirector or FlexMaster to Manage the

Access Point

If you are planning to use either Ruckus Wireless FlexMaster or Ruckus Wireless ZoneDi-

rector to manage the Access Point, this guide describes the required steps that will enable

the Access Point to report to and communicate with FlexMaster or ZoneDirector success-

fully.

■ To set up the Access Point for management by FlexMaster, refer to “(Optional) Set the

FlexMaster Server Address” on page 22.

■ To set up the Access Point for management by ZoneDirector, refer to “Configuring for

Management by ZoneDirector” on page 12

2

Unpacking the ZoneFlex Access Point

Package Contents

2 Unpacking the ZoneFlex Access Point

1. Open the Access Point package, and then carefully remove the contents.

2. Return all packing materials to the shipping box, and put the box away in a dry location.

3. Verify that all items listed in Package Contents

below are included in the package.

Check each item for damage. If any item is damaged or missing, notify your authorized

Ruckus Wireless sales representative.

Package Contents

A complete Access Point package contains all of the items listed below:

■ ZoneFlex 2741 Outdoor Access Point

■ Box containing the PoE injector (not included in some SKUs)

■ Box containing the power adapter (not included in some SKUs)

■ Two-prong plug adapter (for three-prong wall outlet)

■ Mounting kit (see “Mounting Kit Contents” for details)

■ Bag containing bottom Access Point cover and related accessories (see “Bottom Cover

and Accessories” for details)

■ Service Level Agreement / Limited Warranty Statement

■ Regulatory Statement

■ This Getting Started Guide

WARNING: The Ruckus Wireless PoE injector and power adapter (if supplied with your

Access Point) is for indoor use only. Never mount the PoE injector and power adapter

outdoor with the Access Point.

Mounting Kit Contents

■ Dynamic bracket

■ Static bracket

■ Metal plates (2 pieces)

■ Steel clamp

■ Wall anchors (2 pieces)

■ Hex bolts (4 pieces)

■ Machine screws (8 pieces)

■ Split lock washers (4 pieces)

■ Fender washers (4 pieces)

3

Before You Begin

Prepare the Required Hardware and Tools

Bottom Cover and Accessories

■ Bottom cover of the Access Point

■ DC terminal block

■ Black solid rubber stoppers (2 pieces)

■ Black rubber O-ring

■ Green rubber O-ring

■ White P-clip cable clamp (2 pieces)

■ Machine screws (2 pieces)

■ Machine screws with washers (3 pieces)

3 Before You Begin

Before installing and setting up the Access Point, Ruckus Wireless recommends that you

first complete the following pre-installation tasks.

Prepare the Required Hardware and Tools

You must supply the following tools and equipment:

■ A notebook computer running on Windows XP/2000 and installed with one wireless

802.11b/g network card and one Ethernet card

■ 6mm flathead screwdriver

■ 6mm Phillips screwdriver

■ 10mm ratchet wrench

■ 3mm Phillips screwdriver (if you will be using DC power)

■ Electric drill with 8mm drill bit (if mounting on a flat surface)

NOTE: At the beginning of each procedure, this guide lists the specific tools, accessories,

and equipment that you will need to complete the procedure.

4

Before You Begin

Get to Know the Access Point Features

Figure 1 and Figure 2 identify the Access Point features that are relevant to the installation

and mounting instructions that this guide provides. Before you begin the installation

process, Ruckus Wireless recommends that you become familiar with these features.

Figure 1. Access Point LEDs and bottom connectors

Table 1. LEDs and bottom panel connectors

No Label Description

1 LEDs See “LED Colors and What They Mean” below for more

information.

2 RJ45 LAN port that supports Power over Ethernet (PoE) and 10/

100Mbps network connections

1

2

3

4

5

Before You Begin

Get to Know the Access Point Features

LED Colors and What They Mean

Refer to Tab le 2 below for all possible LED states and what they indicate.

3 Reset Using a pointed object (for example, a pen), press this

button to restart the Access Point or to restore it to factory

default settings:

• To restart the Access Point, press the Reset button once.

• To restore the Access Point to factory default, press the

Reset button for six (6) seconds.

WARNING: Restoring the Access Point to factory default

settings removes all configuration changes that you have

made. These include the IP address, password, access

control list, and wireless settings. Returning the

configuration of these features to their factory default

settings may result in network connectivity issues.

4 12V DC In addition to PoE, you can also use direct current or DC

(from a battery, for example) to supply power to the Access

Point.

Table 2. LED states and behaviors

LED Meaning

OPT Not used in this model

DIR • Off: The Access Point is not being managed by

ZoneDirector (standalone mode).

• Green: The Access Point is being managed by

ZoneDirector.

• Flashing green: The Access Point is being managed

by ZoneDirector, but is currently unable to

communicate with ZoneDirector.

Table 1. LEDs and bottom panel connectors

No Label Description

6

Before You Begin

Get to Know the Access Point Features

AIR • Green: The Access Point is functioning as a mesh

AP (MAP) and the wireless signal to its uplink MAP

is good (> 24dbm).

• Fast flashing green (two flashes every second): The

Access Point is functioning as a mesh AP (MAP) and

the wireless signal to its uplink MAP is poor (<

24dbm).

• Slow flashing green (one flash every two seconds):

Mesh networking is enabled, but the Access Point

cannot find a mesh uplink.

• Off: The Access Point is operating in standalone

mode or, if mesh networking is enabled, the Access

Point is functioning as a root AP (RAP).

WLAN • Green: The wireless LAN (WLAN) service is up and

at least one wireless client is associated with it. If

mesh networking is enabled, there are no downlink

MAPs connected to this Access Point.

• Fast flashing green (two flashes every second): The

WLAN service is up and at least one wireless client

is associated with it. Mesh networking is enabled

and at least one downlink MAP is connected to this

Access Point.

• Slow flashing green (one flash every two seconds):

The WLAN service is up, but no wireless clients are

currently associated with it. Mesh networking is

enabled and at least one downlink MAP is

connected to this Access Point.

• Off: Either the WLAN is down, or it is up but no

wireless clients are currently associated with it. If

mesh networking is enabled, there are no downlink

MAPs connected to this Access Point.

LAN • Green: The LAN port is connected to a 10/100Mbps

device.

• Flashing green: Traffic is passing through the LAN

port.

• Off: The LAN port is not connected to any network

device.

Table 2. LED states and behaviors

LED Meaning

7

Before You Begin

Get to Know the Access Point Features

If you want to extend the range of your wireless network, you can connect an external high

gain antenna to the standard N-type radio frequency (RF) antenna connector on the top

panel of the Access Point. The antenna must have a gain of less than 9dBi to comply with

FCC and CE regulations. If you are connecting an external antenna to the Access Point,

refer to “(Optional) Mounting and Connecting the External Antenna”

on page 46 for more

information.

Figure 2. The antenna connector is protected by a black waterproof antenna

connector cover

PWR • Green: The Access Point is connected to a power

source.

• Off: No power is available, or the Access Point is not

connected to a power source.

Table 2. LED states and behaviors

LED Meaning

8

Before You Begin

Perform a Site Survey

Before installing the Access Point, perform a site survey to determine the optimal Access

Point placement or maximum range, coverage, and network performance. When

performing a site survey, consider the following factors:

■ Data rates: Range is generally inversely proportional to data rates. The maximum radio

range is achieved at the lowest workable data rate. Higher data rates will generally be

achieved at closer distances.

■ Antenna type and placement: Proper antenna configuration is a critical factor in

maximizing radio range. As a general rule, radio range is increased by mounting the

radio higher off of the ground with the Access Point oriented so that the dome is facing

down (for recommended orientation examples, refer to Figure 3

on page 9). If you are

connecting an external antenna to the Access Point, mount the Access Point so that

the external antenna is pointing down.

■ Physical environment: Clear or open areas provide better radio range than closed or

filled areas. The less cluttered the operating environment, the greater the wireless

range.

■ Obstructions, building materials, and sources of interference: Physical obstructions,

such as concrete pillars, steel beams, filing cabinets, buildings, or trees, can block or

hinder wireless communication. Avoid installing the Access Point in a location where

there is an obstruction between sending and receiving devices. A number of machines

and electronic devices that emit radio waves – cranes, wireless phones, microwave

ovens, satellite dishes – interfere with and block wireless signals. Building materials

used in construction also influence radio signal penetration. For example, drywall

construction permits greater range than concrete blocks.

For more Access Point placement guidelines, refer to “Determine the Optimal

Mounting Location and Orientation”.

9

Before You Begin

Determine the Optimal Mounting Location and Orientation

Determine the Optimal Mounting Location and

Orientation

The location and orientation that you choose for the Access Point play a critical role in the

performance of your wireless network. In general, Ruckus Wireless recommends installing

the Access Point away from obstructions and sources of interference and ensuring that the

Access Point’s dome is pointing to the general direction of its wireless clients.

Figure 3

illustrates mounting locations and access point orientations Ruckus Wireless

recommends.

Figure 3. Recommended mounting locations and orientations

10

Before You Begin

Determine the Optimal Mounting Location and Orientation

Figure 4 illustrates mounting locations and access point orientations that should be

avoided.

Figure 4. Not recommended mounting locations and orientations

11

Before You Begin

Become Familiar with the Installation Components

The Access Point can be installed in an indoor or outdoor environment, such as an interior

wall or ceiling or the exterior roof overhang of a building or a streetlight pole. Refer to

Figure 5

for the installation components involved in a typical installation.

Take note of the components that must be installed indoor and outdoor. The PoE injector

and power adapter that are shipped with the Access Point are for indoor use only. Ruckus

Wireless also strongly recommends that you form a drip loop on any cable that is

connected to devices that are installed outdoor (for example, the Access Point and the

Ethernet surge protector).

Figure 5. Typical installation components using PoE as the only power source

WARNING: Only trained and qualified personnel should be allowed to install, replace,

or service this equipment.

OUTDOOR

INDOOR

Access Point

Ethernet Surge

Protector

PoE Injector

Router or Switch

Power Adapter

Drip Loop

12

Configuring the Access Point

Configuring for Management by ZoneDirector

WARNING: Installation of the equipment must comply with local and national electrical

codes.

CAUTION: Make sure that you form a 3”-5” drip loop in any cable that is attached to the

Access Point and Ethernet surge protector. This will prevent water from running along the

cables and entering the Access Point, Ethernet surge protector, or the building where the

cables terminate.

CAUTION: Be sure that grounding is available and that it meets local and national

electrical codes. For additional lightning protection, use lightning rods, lightning arrestors,

or surge suppressors.

.

WARNING: The Ruckus Wireless PoE injector (if supplied with your Access Point) is for

indoor use only. Never mount the PoE injector outdoor with the Access Point.

NOTE: If the power outlet in your installation environment is three-pronged, use the two-

prong plug adapter that is shipped with the Access Point.

4 Configuring the Access Point

The procedure for completing the Access Point’s essential configuration depends on

whether you want it to be managed by either ZoneDirector or FlexMaster or to operate

as a standalone access point. Refer to the section that is relevant to your deployment:

■ Configuring for Management by ZoneDirector

■ Configuring for Standalone Operation or for Management by FlexMaster

Configuring for Management by ZoneDirector

If ZoneDirector is installed on the network, you can configure the Access Point for

management by ZoneDirector. Simply connect the Access Point to same Layer 2 subnet

as ZoneDirector. When the Access Point starts up, it will discover and register with

ZoneDirector automatically.

13

Configuring the Access Point

Configuring for Management by ZoneDirector

NOTE: In addition to using Layer 2 auto discovery to enable the Access Point to register

with ZoneDirector, you can also use DHCP Option 43 or DNS. For more information, refer

to the ZoneDirector User Guide.

CAUTION: If you use this method, make sure that you do not change the IP address of

ZoneDirector after the AP discovers and registers with it. If you change the ZoneDirector

IP address, the AP will no longer be able to communicate with it and will be unable to

rediscover it.

Before starting this procedure, check the back panel of the Access Point (above the recess

where the bottom connectors are located), and then write down the MAC address of the

Access Point. You will need the MAC address to identify the Access Point on the ZoneDi-

rector Web interface.

1. Connect the Access Point to the same Layer 2 subnet as ZoneDirector. The same Layer

2 subnet means that there should not be any router between the Access Point and

ZoneDirector.

2. Power on the Access Point.

3. Log into ZoneDirector, and then go to the Monitor > Access Points page.

4. Look for the MAC address of the Access Point, and then check its Status column.

• If automatic approval is enabled, the Status column should show Connected.

• If automatic approval is disabled, click the Allow link that is on the same row as the

Access Point’s MAC address. This allows the Access Point to register with ZoneDi-

rector.

When the Status column shows Connected, this indicates that the Access Point has

successfully registered with ZoneDirector and that it can now be moved to its destina-

tion Layer 2 or Layer 3 network.

5. Continue to “Attaching the Mounting Brackets” on page 25.

14

Configuring the Access Point

Configuring for Standalone Operation or for Management by FlexMaster

Configuring for Standalone Operation or for

Management by FlexMaster

What You Will Need

Before starting with the configuration task, make sure that you have the following require-

ments ready:

■ An administrative computer (notebook computer) running on Microsoft Windows

Vista/XP/2000

■ Mozilla Firefox 2.0 (or later) or Microsoft Internet Explorer 6.0 (or later) installed on the

administrative computer

■ One Cat5e UTP (outdoor-rated) solid cable

■ One Ethernet cable

■ PoE injector (if not supplied with the Access Point, you can purchase a third party

802.3af-compliant PoE injector or switch)

■ 6mm Phillips screwdriver

If you are planning to power the Access Point using a 12v DC connection, you will also

need the following:

■ UL1185 (80°, 300V) single shielded DC cable

■ 12v DC, 1A DC power source (for example, a battery)

■ 3mm Phillips screwdriver

Step 1: Prepare the Administrative Computer

NOTE: The following procedure is applicable if the administrative computer is running

on Windows XP or Windows 2000. If you are using a different operating system, refer to

the documentation that was shipped with your operating system for information on how

to modify the computer’s IP address settings.

1. On your Windows XP or Windows 2000 computer, open the Network Connections (or

Network and Dial-up Connections) control panel according to how the Start menu is

set up:

• On Windows XP, click Start > Control Panel > Network Connections.

• On Windows 2000, click Start > Settings > Network Connections.

2. When the Network Connections window appears, right-click the icon for Local Area

Connection, and then click Properties.

15

Configuring the Access Point

Configuring for Standalone Operation or for Management by FlexMaster

NOTE: Make sure that you configure the Local Area Connection properties, not the

Wireless Network Connection properties.

3. When the Local Area Connection Properties dialog box appears, select Internet

Protocol (TCP/IP) from the scrolling list, and then click Properties. The Internet

Protocol (TCP/IP) Properties dialog box appears.

4. Write down all of the currently active network settings. You will need this information

later when you restore your computer to its current network configuration.

5. Click Use the following IP address, and then configure the IP address settings with

the values listed in Tabl e 3

. For a sample configuration, refer to Figure 6.

You can leave the Alternate DNS server box blank.

6. Click OK to save your changes and close the TCP/IP Properties dialog box.

7. Click OK again to close the Local Area Connection Properties dialog box.

Windows saves the IP address settings that you have configured.

Table 3. Configure your computer’s IP address settings

IP address 192.168.0.22 (or any address in the 192.168.0.x

network—with the exception of 192.168.0.1, which

is already used by the Access Point)

Subnet mask 255.255.255.0

Default gateway 192.168.0.1

Preferred DNS server 192.168.0.1

16

Configuring the Access Point

Configuring for Standalone Operation or for Management by FlexMaster

Figure 6. Sample configuration in the Internet Protocol (TCP/IP) Properties dialog box

Step 2: Connect the Access Point to the Administrative

Computer

The procedure for connecting the Access Point to the administrative computer depends

on the power source that you will be using. You can do one of the following:

■ Use Power Over Ethernet

■ Use DC Power

NOTE: You only need to connect one type of power source at this point, even if you are

planning to use both PoE and DC power in your final deployment.

Use Power Over Ethernet

1. Take out the PoE injector and the power adapter from the Access Point package.

2. Connect one end of an Ethernet cable to the 10/100 DATA IN port on the PoE injector,

and then connect the other end to the administrative computer’s Ethernet port.

3. Connect one end of the other Ethernet cable to the PoE Out port on the PoE injector,

and then connect the other end to the RJ45 port on the Access Point.

La pagina sta caricando ...

Ruckus Wireless ZoneFlex 2741 Manuale utente

Questo manuale è adatto anche per

Ruckus Wireless ZoneFlex 2741 Manuale utente

in altre lingue

Documenti correlati

Altri documenti