CET s.r.l.
Vers. 1.1
GFM 41
Pag. 1
CET
VISUALIZED DIGITAL
PERIOD COUNTER
WITH ONE SET POINT
Type:
GFM41
PROGRAMMABLE DIGITAL VISUALIZATOR OF
ROTATIONS WITH 4 DIGITS, ONE SET POINT AND
THE INPUT SUITABLE FOR MONO DIRCTIONAL
COUNTING.
The period counter model GFM41 is used to display and
control, through a relay threshold, rotational or linear
speeds or counting referred to a pre selected time base.
All the common types of controls are available using five
different programmable operations.
It reads signals coming form electromechanical and
logical contacts, proximity switches and encoder.
It finds application like RPM meter, tachometer, speed
meter, productions meter etc.
MAIN FEATURES
PROGRAMMABLE PARAMETERS
• Frontal keyboard in polycarbonate (antiscratch, antioil,
antacid).
• IP65 protection degree
• Accessible parameters with key software
• Removable terminals connection.
• Execution DIN 48 x 48.
• Recessed assembly.
• Special retaining brackets.
• One Set Point
• One Hysteresis
• Multiplier Factor
• Divisor Factor
• Time Base
• Operation Mode
• Inhibit Time
• Display Reset Time
• Display Adjournment Time
• Input for Electromechanical or Logic Contacts
• Programmable Reset Key
• Programmable Decimal Point
TECHNICAL FEATURES
• POWER SUPPLY IN ALTERNATE CURRENT
• POWER SUPPLY IN DIRECT CURRENT
• POWER SUPPLY TOLERANCE
• ABSORPTION
• OPERATING TEMPERATURE
• CLIMATIC CONDITIONS
• COUNTER AND TOTALIZER VISUALIZATION
• MULTIPLICATION FACTOR OF THE INPULSES IN INPUT
• DIVISOR FACTOR OF THE INPULSES IN INPUT
• TIME BASE
• INPUT TYPE
• MAXIMUM COUNT FREQUENCY
• MINIMUM TIME FOR INPULSES COUNT
• CUT OFF FREQUENCY FOR ELECTROMECHANICAL
INPUTS
• COMMAND INPUTS
• OUTPUTS
• RESET RELAY
• AUXILIARY INPUT SUPPLY
• PROGRAMMED DATA MEMORY
: 230 Vac (50 / 60 Hz).
: 24 Vdc
: +10% - 15%.
: 2 W - 3 VA.
: -5 °C + 55 °C.
: U.R. 95 % a 40 °C (without condensate).
: 4 digits, display high 11mm.
: programmable from 1 to 10000.
: programmable from 1 to 10000.
: Programmable between 1 / 60 / 3600.
: suitable for electromechanical contacts, amplified proximity
and encoder, NPN and PNP
: up to 25 KHz with Duty Cycle=50%.
: 0,25 mSec.
: about 30 Hz.
: 1 RESET, 1 INHIBIT
: 1 RELAY with operational contacts; 2A - 250VAC / 30VDC
: manual or automatic
: 24 Vdc - 80 mA available on terminals.
: Static (no battery)
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 2
DESCRIPTION OF THE FRONTAL KEYBOARD
ø
WHITE
In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is on the right side first one on
the. At the end it resumes from the first one to right.
ù
WHITE
The key 'UP ARROW' in normal operating phase visualizes the totalizer of impulses.
In programming phase it increases the value of the blinking figure.
ú
WHITE
The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display C.0000.
In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The instrument exits automatically
from the programming phase, 60 sec. after the pressure of the last key.
û
RED
The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it attributed in the programming phase.
In programming phase it confirms and memorizes the visualized data and passes to the successive function. If it has arrived to list end
it resumes from the beginning.
INPUTS / OUTPUTS DESCRIPTION - E SERIES
AC POWER SUPPLY
(inputs 1-2)
AC Power Supply Input of the instrument; it can be to 24 - 110 - 230 VAC in according to demand.
DC POWER SUPPLY
(inputs 3-4)
DC Power Supply Input of the instrument; input 3 (-), input 4 (+).
24 VDC - 80mA
(inputs 12-13)
24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and proximity amplified.
PRI
(input 10)
Input used for the polarization of the count and command inputs : connecting the PRI output to input 13 it configures the instrument in
Negative logic (NPN), connecting the PRI output to input 12 it configures the instrument in Positive logic (PNP).
INPUT
(input 11)
Input of count adapted for electromechanical and logical contacts, encoder and 3 wires proximity amplified, configurable in Positive
(PNP) and Negative (NPN) logic through PRI input (10).
RESET
(input 7)
Input of RESET that executes the reset of the visualized count showed on display at the moment of its activation.
INHIBIT
(input 8)
Input of count inhibition: when activated it blocks the relay operation like programmed under the code 020.
RL1
(inputs 5 - 6 - 9)
Output of Relay 1, connected to the operation of the Set Point S1. The Common, Normally Open and Normally Close contacts are
available.
INPUTS / OUTPUTS DESCRIPTION - Z SERIES
AC/DC POWER
SUPPLY
(inputs 2 - 10)
AC or DC Power Supply Input of the instrument; it can be to 24 - 110 - 230 VAC or 12 - 24 VDC in according to demand.
24 VDC - 80mA
(inputs 7 - 8)
24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and proximity amplified.
PRI
(input 9)
Input used for the polarization of the count and command inputs : connecting the PRI output to input 8 it configures the instrument in
Negative logic (NPN), connecting the PRI output to input 7 it configures the instrument in Positive logic (PNP).
INPUT
(input 5)
Input of count adapted for electromechanical and logical contacts, encoder and 3 wires proximity amplified, configurable in Positive
(PNP) and Negative (NPN) logic through PRI input (9).
RESET
(input 6)
Input of RESET that executes the reset of the visualized count showed on display at the moment of its activation.
RL1
(inputs 1 - 3 - 4)
Output of Relay 1, connected to the operation of the Set Point S1. The Common, Normally Open and Normally Close contacts are
available.
DESCRIPTION OF THE LED’S OPERATION
LED 1
It comes activated to the reaching of the Set Points S1.
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 3
SET POINT AND HYSTERESIS PROGRAMMATION
For SET POINT and HYSTERESIS programming access, proceed as follow:
- Press key ‘PRG’ in impulsive mode; on display appears:
5¿1<
1000
SG.1 = SET POINT 1, main Set Point, programmable between 0 and 9999.
HSÌ<
100
HSt. = Hysteresis, programmable between 0 and 9999. It is active in Mode 2 and 3 only.
Key ENT confirms the data. In order to exit the programming, press key PRG.
PROGRAMMING OF THE OPERATION PARAMETERS
The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key PRG for about 2 sec. On the display appears:
Cod
000
GROUP 1
:
in order to approach the parameters of group 1, insert code
101
and press
ENT
¾Æ
0001
F.M. = 4 digits multiplier , programmable from 1 to 10000. This parameter allows to multiply
the number of the input impulses, showing them on the display in an other format. If it
programmed = 0 it means programmed 10000.
Attention: the variation of the value of the multiplying modifies automatically the value of the
count and the totalizer.
¾¼
0001
F.d. = 4 digits divisor , programmable from 1 to 10000. This parameter allows to divide the
number of the input impulses, showing them on the display in an other format. If it programmed
= 0 it means programmed 10000.
Attention: the variation of the value of the multiplying modifies automatically the value of the
count and the totalizer.
ºÌ
60
b.t. = Time Base.
This programming allows to select in which time base shows on the display the measure in
input. There are three scales:
1 = Time Base: seconds, measure visualization in seconds (ex. Meters/seconds)
60 = Time Base: minutes, measure visualization in minutes (ex. Liters/minutes)
3600 = Time Base: hours, measure visualization in hours (ex. Bottles/hour)
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 4
PROGRAMMING OF THE OPERATION PARAMETERS
The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key
PRG
for about 2 sec. On the display appears:
Cod
000
GROUP 2
:
in order to approach the parameters of GROUP 2, insert code
020
and press
ENT
½òÇ1
E.i = Delay Time for the excitation of the Relay output.
This parameter allows to program the delay time of the activation of the Relay output RL1. It’s
programmable between 0 (no delay) and 9,9 sec.
¼òÇ1
d.i = Delay Time for the unexcitation of the Relay output.
This parameter allows to program the delay time of the unactivation of the Relay output RL1.
It’s programmable between 0 (no delay) and 9,9 sec.
Ìê10
t.r. = Reset time of the display.
This parameter allows to program the maximum time from the last impulse after that the
instrument reset the display, showing the four horizontal bars. If programmed = 0, with no
impulses in input the instrument shows the last calculated value. If the programmed time is
lower than the time between the impulses, the instrument shows the four horizontal bars.
This parameter is useful to indicate when a plant is in stop or when there are no
impulses in input or when the impulses source is damaged. It’s programmable
between 1 (instantaneous) and 99 seconds.
̼ Ç1
t.d. = Updating time of the display.
This parameter allows to program the delay time of the data adjournment on the
display. It’s programmable between 0 (instantaneous) and 9,9 sec
1æ F
1æ 5
Input Fast - Slow.
This programming allows to set the count input to read signals coming from electromechanical
contacts (relays, switches etc.) or from logical signals like proximity switches transistor and
encoder.
In = F. sets the input to read digital signals up to 28 KHz.
In = S. sets the input to read electromechanical signals up to 25 Hz.
rËoí
Operation of the RESET Key; this programming enable and disable the RESET working of
the frontal RES key during the operation, as in the following modes:
RS.ou. = executes the RESET of the visualized parameter + the Relay Output
RS.on. = executes the RESET of the visualized parameter
RS.oF. = RESET working of the RES key excluded.
RS.F.t. = executes, at the same time, the RESET of the frequencymeter, of the totalizer and
of the Relay Output
¼È O
¼È 4
d.P. = Programming of the Decimal Point
This programming allows to add a decimal point to the visualization on the 4 digits, in order to
obtain counts with various resolutions.
d.p. = 0 Decimal Point excluded; visualization 9999
d.p. = 1 Decimal Point on the second display from right; visualization 999,9
d.p. = 2 Decimal Point on the third party display from right; visualization 99,99
d.p. = 3 Decimal Point on the fourth display from right; visualization 9,999
d.p. = 4 Floating Point.
Á 001
I = Initial Time of inhibition of the activation of the Relay output.
This parameter allows to inhibit the activation of the relay output for the time sets. During this
time the relay output is excluded. It’s operation follows the programming in Ut. under the code
121. It’s programmable between 0 (excluded) and 999 sec.
¹È È
¹È ê
A.P. = Activation mode of the programmed parameters.
With this programming is possible to activate the executed programmings directly to the exit of
the programming or, when exited of the programming, after a RESET (with frontal key or from
rear input).
A.P. = P. Activation of the parameters to the exit of the programming.
A.P. = r. Activation of the parameters to the exit of the programming after a RESET.
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 5
----
When the device is switched on and when there are no impulses in its input, the device visualize 4
horizontal bars.
Pressing the key ù the totalizer of impulses will be visualized for 5 sec.
Toì
9999
The totalizer visualizes all the impulses that the instrument counts from its input IN1.
It can be resetted through frontal key RES only or from RESET input when it is visualized on the display.
PROGRAMMING OF THE OPERATION PARAMETERS
The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key
PRG
for about 2 sec. On the display appears:
Cod
000
GROUP 3
:
in order to approach the parameters of GROUP 3, insert code
121
and press
ENT
N¼ 0
Md. = Programming of the operation Mode
This programming allows to program the operation mode of the set point, of the Hysteresis and
of the Relay Output.
Md. = 0 Lower Set Point (excited relay under the Set Point value)
Md. = 1 Upper Set Point (excited relay over the Set Point value)
Md. = 2 Upper Set Point + Hysteresis (excited relay over the Set Point value and unexcitated
under the Hysteresis value)
Md. = 3 Lower Set Point + Hysteresis (excited relay under the Set Point and unexcitedted over
the Set Point + Hysteresis value)
Md. = 4 Lower Set Point + maintained relay (the relay rests always excited when is over the
Set Point value too. It can be reset with a RESET command or switching off and on
the device).
Md. = 5 Upper Set Point + maintained relay (the relay rests always excited when is over the
Set Point value too. It can be reset with a RESET command or switching off and on
the device).
.
UÌ 0
Ut. = Programming of the RESET Input and of the operation of the INHIBIT time.
This programming allows to select the operation of the RESET input and the operation mode
of the Inhibit time.
Ut. = 0 Reset of the visualized value + relay (with inhibit time at the starting)
Ut. = 1 Frequency Reset only + relay (with inhibit time at the starting)
Ut. = 2 Frequency Reset + totalizer (at the same time) + relay (with inhibit time at
the starting)
Ut. = 3 Reset of the visualized value + relay (with inhibit time with the first impulse)
Ut. = 4 Frequency Reset only + relay (with inhibit time with the first impulse).
Ut. = 5 Frequency Reset + totalizer (at the same time) + relay (with inhibit time with the first
impulse).
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 6
DECLARATION OF ‘CE’ CONFORMITY
CE NORMATIVE CONFORMITY
Borgolavezzaro, October, 03rd 2005
The building firm:
CET s.r.l.
Head office:
Strada Statale 211, Km 53,3
28071 Borgolavezzaro (No) ITALIA
Tel. 0039 - 321 - 885301 Fax. 0039 - 321 - 885560
declare that the products:
type :
Visualized Digital Period Counter
model:
GFM41
use class:
Industrial
are in conformity with the following normatives:
EN55011
ENV50141
ENV50204
EN61000-4-2
EN61000-4-4
The constructor :
CET s.r.l.
________________________________
Signature
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 7
Z SERIES - CONNECTIONS
Z SERIES - INPUT SIGNALS
NPN
-
+ - + - + + -
INPUT FOR INPUT FOR INPUT FOR INPUT FOR
NPN NPN PROXIMITY AND NPN
CONTACT LOGIC ENCODER RESET
AMPLIFIED
24 VDC
PNP
-
- + - + - + +
INPUT FOR INPUT FOR INPUT FOR INPUT FOR
PNP PNP PROXIMITY AND PNP
CONTACT LOGIC ENCODER RESET
AMPLIFIED
24 VDC
Z SERIES - CONNECTIONS
E SERIES - INPUT SIGNALS
NPN
-
+ - + - + + - -
INPUT FOR INPUT FOR INPUT FOR RESET INHIBIT
NPN NPN PROXIMITY AND NPN
CONTACT LOGIC ENCODER
AMPLIFIED
24 VDC
PNP
-
- + - + - + + +
INPUT FOR INPUT FOR INPUT FOR RESET INHIBIT
PNP PNP PROXIMITY AND PNP
CONTACT LOGIC ENCODER
AMPLIFIED
24 VDC
7
5
8
9
5
7
8
9
8
9
PROX
ENC
7
8
5
7
6
8
5
7
9
5
8
7
9
7
9
PROX
ENC
7
8
5
8
6
12
11
13
10
11
12
13
10
13
10
PROX
ENC
12
13
11
13
11
12
10
11
13
12
10
12
10
PROX
ENC
12
13
11
12
7
12
8
13
7
13
8
PRI
1
GND
11
2
3
4
5
6
7
8
9
10
+ 24 VDC
Reset
CNT
RL1
24 VDC
-
+
DC POWER
SUPPLY
PRI
1
GND
11
2
3
4
5
6
7
8
9
10
+ 24VDC
Reset
CNT
RL1
AC POWER
SUPPLY
-
+
24 VDC
INPUT
INHIBIT
7
8
9
10
11
12
13
1
2
3
4
5
6
PRI
RESET
AC POWER
SUPPLY
RL1
24 VDC
-
+
CET s.r.l.
Vers. 1.1
GFM 41
Pag. 8
OVERALL DIMENSIONS (mm)
FRONT DRILL TEMPLATE
E SERIES SIDE Z SERIES SIDE
E SERIES REAR
Z SERIES REAR
CET
CETCET
CET
CET
CETCET
CET
s.r.l.
Strada Statale 211 Km 53,550
28071 Borgolavezzaro - NO - ITALY
Tel : ++39 0321-885180/885301/885807
Fax : ++39 0321-885560
http://www.cet-italy.com
e-mail: info@cet-italy.com
Agent:
45
45
48
48
ENT
PRG
electronic counter GFM
L1 L2
RES
CET
CETCET
CET
5952
116
93
4
19
44x44
REMOVABLE
TERMINALS
RETAINING
BRACKETS
10
116
93
4
12
44x44
UNDECAL
SOCCAL
RETAINING
BRACKETS
10
44
44
7 8 9 10 11 12 13
1 2 3 4 5 6
44
44
1 11
2
3
4
5
6
7
8
9
10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
in altre lingue
- English: CET GFM41 Owner's manual
Documenti correlati
-
CET LFM52 Manuale del proprietario
-
CET NFM42 Manuale del proprietario
-
CET LFM50 Manuale del proprietario
-
CET LCM81 Manuale del proprietario
-
CET NCM52 Manuale del proprietario
-
CET GCM50 Manuale del proprietario
-
CET LCM60 Manuale del proprietario
-
CET LBM62/ID Manuale del proprietario
-
CET LBP82 Manuale del proprietario
-
CET NCM50 Manuale del proprietario
