Standard Horizon CMP31 Manuale del proprietario

CMP31
Standard Horizon
Marca
Standard Horizon
Modello
CMP31
Tipo
Manuale del proprietario
RAM3+
(
CMP31
)
Remote Station Microphone
The RAM3+
(
CMP31
)
allows you to remotely control all functions of Standard Hori-
zon xed mount VHF radios which include GX1600, GX1700, GX2000, GX2100,
GX2150, GX2200 and GX5500S. The full dot matrix display and programmable
keys make operation simple and fast. Additional features include turning the ra-
dio on/off and all DSC functions including Distress. The RAM3+
(
CMP31
)
can be
extended up to 70 feet using the optional CT-100 (23 Foot) extension cable. The
RAM3+
(
CMP31
)
is backed by an industry leading 3-year waterproof warranty.
WARNING: Do not connect or remove the CMP31 (RAM3+) microphone while
the radio is powered on. This may result in equipment failure.
1. Connect the Extension Cable to the 8-pin connector on the transceivers rear
panel, then tighten the Cable Nut (Figure 1).
2. Referring to Figure 2, attach the supplied ferrite core as close as possible to the
MIC plug of the Routing Cable and External Speaker Connections, then snap its
two halves together. And then, wind some plastic tape around the ferrite core, to
prevent vibration from causing the two halves to split apart and fall off the wires.
3. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall then insert the Exten-
sion Cable into this hole. Connect the Gasket and Mount Base to the Extension
Cable Connector using the Nut.
4. Drill the four Screw holes (approx. 2 mm) on the wall then install the Mounting
Bracket to the wall using four screws.
5. Put the Rubber Cap on to the Nut.
6. The installation is now complete. Connect the RAM3+
(
CMP31
)
to the Extension
Cable Connector and tighten the Cable Nut.
RAM3+
(
CMP31
)
InstallatIon
FIgure 1
FIgure 3
Included accessorIes and replacement part numbers
1. 23-Foot Routing Cable (S8101512)
2. Rubber Cap (RA052520A)
3. Mounting Bracket (RA0525100) & Screws (U24312020 x 4 pcs)
4. Microphone Hanger (RA0458800: Black or RA0436000: White) &
Screws (U40412220 x 2 pcs)
5. Ferrite Core (L9190198 or L9190192)
FIgure 2
Wall
Gasket
Mounting Bracket
Routing Cable
Cap
Nut
External Speaker Connections
Ferrite Core
As close as possible
Routing Cable or
CT-100 Extension Cable
Ferrite Core
Snap together
External Speaker
Connections
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Owner’s Manual
The details of the installation and operation of the RAM3+
(
CMP31
)
is included
in the owner’s manual of the compatible xed mount radio, or it can be down
-
loaded at www.standardhorizon.com. If you have any questions or comments,
please contact Standard Horizon Marine Product Support at 800/767-2450.
NOTE
Caution!: Before cutting the cable, it must be disconnected from the rear panel of
the transceiver.
The routing cable can be cut and spliced, however care needs to be taken
when reconnecting the wires to ensure water integrity.
After cutting you will notice there are the following wires:
Yellow, Green, Brown, Purple, Blue, Green, Red
, and Shield

The Red and Shield wires are wrapped in foil. Remove the foil, and sepa-
rate the Red and Shield wires.
1
2
3 4 5
optIonal accessorIes
ct-100 23Ft extensIon cable
mls-310 10 watt amplIFIed speaker
mls-300 external loud speaker
specIFIcatIons
Supply voltage: 13.8 VDC (Supplied from the transceiver)
Current consumption: 700 mA @VOL Max.
200 mA @AF Mute
Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C)
MIC. Sensitivity (Typical): 60 mVrms
@ 1 kHz Tone with 3 kHz Deviation
MIC. Impedance: 2 k
AF output: 800 mW @ 8
for 10 % THD
(Internal Speaker)
3 W @ 4
for 10 % THD
(External Speaker)
Display Size: 1.8” x 0.9” (45 x 23 mm)
Display Resolution: 132 x 64 dot
Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
Weight (Approx): 12.9 oz (365g)
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as
household waste.
Electronic and Electric Equipment should be recycled at a facility
capable of handling these items and their waste byproducts.
In EU countries, please contact your local equipment supplier
representative or service center for information about the waste
collection system in your country.
DISTRESS
BUSY
1602O-BO
RAM3+
(
CMP31
)
controls
À
[
H/L
]
Key
Press this key to toggle the transmit power between high and low. When the
[
H/L
]
key is pressed while the transceiver is on channel 13 or 67, the power will temporarily
switch from LOW to HI power until the PTT is released. The
[
H/L
]
key does not function
on transmit inhibited and low power only channels.
Á
PTT
(
Push-To-Talk
)
Key
Press this key to activate the transmission.
Â
POWER
(
)
Key
Press and hold down this key to turn to the transceiver and RAM3+
(
CMP31
)
“on” and
“off”.
Ã
Microphone
The internal microphone is located here.
When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from
the small mic hole. Speak slowly and clearly into the microphone.
Ä
DISPLAY
Channel display.
Å
SOFT KEY
For details, refer to owner’s manual of the transceiver.
Æ
KEY PAD
[
CALL/MENU
]
Key
Press this key to access the DSC OPERATION menu.
Press and hold this key to access the SETUP menu.
[
16/9
]
Key
First press: channel 16 is immediately selected.
Second press: recalls the last selected channel.
Press and hold: selects channel 9.
[
](
UP
)
/
[
](
DOWN
)
Key
These keys are used to select channels, adjust the volume and squelch level, and to
choose DSC calls, DSC setup and Radio setup function.
[
VOL/SQ
]
Key
(
Volume Control / Squelch Control
)
Press this key to toggle the function of the microphone’s
[
]
or
[
]
key between the
channel selections, volume level adjustment, and squelch level adjustment.
[
CLR/WX
]
Key
For details, refer to owner’s manual of the transceiver.
[
ENT
]
Key
This key functions as the enter key.
Ç
Speaker
The internal speaker is located here.
È
[
DISTRESS
]
KEY
This key is used to send a DSC Distress Call.
Lift the red spring loaded DISTRESS cover, then press and hold in the
[
DISTRESS
]
key.
⑤
①
②
③
④
⑥
⑦
⑧
DISTRESS
BUSY
⑨
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
Type of Equipment: Remote Station Microphone
Brand Name: STANDARD HORIZON
Model Number: CMP31
Manufacturer: YAESU MUSEN CO., LTD.
Address of Manufacturer: Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa,
Shinagawa-ku,Tokyo 140-0002 Japan
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions; (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The technical documentation as required by the Conformity Assessment procedures is kept at
the following address:
Company: Yaesu U.S.A.
Address: 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
Telephone: (714) 827-7600
Changes or modications to this device not expressly approved by YAESU MUSEN
could void the user’s authorization to operate this device.
  • Page 1 1
  • Page 2 2

Standard Horizon CMP31 Manuale del proprietario

CMP31
Standard Horizon
Marca
Standard Horizon
Modello
CMP31
Tipo
Manuale del proprietario
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti